Add regulator header file missing kernel-doc:
Warning(include/linux/regulator/driver.h:117): No description found for parameter 'set_mode'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
cc: Liam Girdwood <lrg@slimlogic.co.uk>
cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
At present it is not possible for machine constraints to disable
regulators which have been left on when the system starts, for example
as a result of fixed default configurations in hardware. This means that
power may be wasted by these regulators if they are not in use.
Provide intial support for this with a late_initcall which will disable
any unused regulators if the machine has enabled this feature by calling
regulator_has_full_constraints(). If this has not been called then print
a warning to encourage users to fully specify their constraints so that
we can change this to be the default behaviour in future.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Rather than incrementing the reference count for boot_on regulators
(which prevents them being disabled later on) simply force the
regulator to be enabled when applying the constraints. Previously
boot_on was essentially equivalent to always_on.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add kerneldoc for the new get_status() message. Fix the existing
kerneldoc for that struct in two ways:
(a) Syntax, making sure parameter descriptions immediately
follow the one-line struct description and that the first
blank lines is before any more expansive description;
(b) Presentation for a few points, to highlight the fact that
the previous "get" methods exist only to report the current
configuration, not to display actual status.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add a basic mechanism for regulators to report the discrete
voltages they support: list_voltage() enumerates them using
selectors numbered from 0 to an upper bound.
Use those methods to force machine-level constraints into bounds.
(Example: regulator supports 1.8V, 2.4V, 2.6V, 3.3V, and board
constraints for that rail are 2.0V to 3.6V ... so the range of
voltages is then 2.4V to 3.3V on this board.)
Export those voltages to the regulator consumer interface, so for
example regulator hooked up to an MMC/SD/SDIO slot can report the
actual voltage options available to cards connected there.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This is useful when wishing to run in a fixed operating mode that isn't
the default.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Remove deceased email address and update to new address. Also update
website details in MAINTAINERS with correct page.
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Fix regulator/driver.h missing kernel-doc:
Warning(linux-next-20090120//include/linux/regulator/driver.h:108): No description found for parameter 'get_status'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
cc: Liam Girdwood <lrg@slimlogic.co.uk>
cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Commit 872ed3fe176833f7d43748eb88010da4bbd2f983 caused regulator drivers
to take the struct regulator_dev lock themselves which requires that the
struct be visible to them. Band aid this by making the struct visible.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Previously it was not possible to do so, making it impossible for
machines to configure the driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Rather than having the regulator init data read from the platform_data
member of the struct device that is registered for the regulator make
the init data an explict argument passed in when registering. This
allows drivers to use the platform data for their own purposes if they
wish.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Regulator: Push lock out of _notifier_call_chain and into caller functions
(side effect of fixing deadlock in regulator_force_disable)
+ Add a voltage changed event.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Based on previous LKML discussions:
* Update docs for regulator sysfs class attributes to highlight
the fact that all current attributes are intended to be control
inputs, including notably "state" and "opmode" which previously
implied otherwise.
* Define a new regulator driver get_status() method, which is the
first method reporting regulator outputs instead of inputs.
It can report on/off and error status; or instead of simply
"on", report the actual operating mode.
For the moment, this is a sysfs-only interface, not accessible to
regulator clients. Such clients can use the current notification
interfaces to detect errors, if the regulator reports them.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Fix kernel-doc warnings in regulator/driver.h:
Warning(linux-next-20090108//include/linux/regulator/driver.h:95): Excess struct/union/enum/typedef member 'set_current' description in 'regulator_ops'
Warning(linux-next-20090108//include/linux/regulator/driver.h:95): Excess struct/union/enum/typedef member 'get_current' description in 'regulator_ops'
Warning(linux-next-20090108//include/linux/regulator/driver.h:124): No description found for parameter 'irq'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
cc: Liam Girdwood <lrg@slimlogic.co.uk>
cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This is only the documentation that the kerneldoc system warns about.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Remove kerneldoc warnings that don't relate to missing documentation,
mostly by renaming parameters in the documentation to match their
actual names.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This improves the machine level API in order to configure
regulator constraints and consumers as platform data and removes the
old string based API that required several calls to set up each regulator.
The intention is to create a struct regulator_init_data, populate
it's fields with constraints, consumers devices, etc and then register
the regulator device from board.c in the standard Linux way.
e.g. regulator LDO2 (supplying codec and sim) platform data.
/* regulator LDO2 consumer devices */
static struct regulator_consumer_supply ldo2_consumers[] = {
{
.dev = &platform_audio_device.dev,
.supply = "codec_avdd",
},
{
.dev = &platform_sim_device.dev,
.supply = "sim_vcc",
}
};
/* regulator LDO2 constraints */
static struct regulator_init_data ldo2_data = {
.constraints = {
.min_uV = 3300000,
.max_uV = 3300000,
.valid_modes_mask = REGULATOR_MODE_NORMAL,
.apply_uV = 1,
},
.num_consumer_supplies = ARRAY_SIZE(ldo2_consumers),
.consumer_supplies = ldo2_consumers,
};
/* machine regulator devices with thier consumers and constraints */
static struct platform_device wm8350_regulator_devices[] = {
{
.name = "wm8350-regulator",
.id = WM8350_LDO_2,
.dev = {
.platform_data = &ldo2_data,
},
},
};
Changes in detail:-
o Removed all const char* regulator config functions in machine API.
o Created new struct regulator_init_data to contain regulator
machine configuration constraints and consmuers.
o Changed set_supply(), set_machine_constraints(),
set_consumer_device_supply() to remove their string identifier
parameters. Also made them static and moved functions nearer top of
core.c.
o Removed no longer used inline func to_rdev()
o Added regulator_get_init_drvdata() to retrieve init data.
o Added struct device* as parameter to regulator_register().
o Changed my email address.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This adds a regulator driver for the TI bq24022 Single-Chip
Li-Ion Charger with its nCE and ISET2 pins connected to GPIOs.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
This patch adds support for fixed regulators. This class of regulator is
not software controllable but can coexist on machines with software
controlable regulators.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
This interface is for machine specific code and allows the creation of
voltage/current domains (with constraints) for each regulator. It can
provide regulator constraints that will prevent device damage through
overvoltage or over current caused by buggy client drivers. It also
allows the creation of a regulator tree whereby some regulators are
supplied by others (similar to a clock tree).
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This allows regulator drivers to register their regulators and provide
operations to the core. It also has a notifier call chain for propagating
regulator events to clients.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support to allow consumer device drivers to control their regulator
power supply.
This uses a similar API to the kernel clock interface in that consumer
drivers can get and put a regulator (like they can with clocks atm) and
get/set voltage, current limit, mode, enable and disable. This should
allow consumers complete control over their supply voltage and current
limit. This also compiles out if not in use so drivers can be reused in
systems with no regulator based power control.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Randy Dunlap