We were checking whether the supplied edid matched the connector it was
read from. We do this in case a DDC read returns an EDID for another
device on a multifunction or otherwise interesting card. However, we
failed to include LVDS as a digital device and so rejecting an otherwise
valid EDID.
Fixes the detection of the secondary SDVO LVDS panel on the Libretto
W105.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=39216
Signed-off-by: Keith Packard <keithp@keithp.com>
v2: add a CPT-specific macro, make code cleaner
v3: fix commit message
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41272
Cc: stable@kernel.org
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Well almost anyway. IVB has 3 planes, pipes, transcoders, and FDI
interfaces, but only 2 pipe PLLs. So two of the pipes must use the same
pipe timings (e.g. 2 DP plus one other, or two HDMI with the same mode
and one other, etc.).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
This is general TMDS detect, not HDMI specifically.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
I can't think of any sensible reason to limit this to a mask of 0x0f,
ie, SDVO_OUTPUT_{TMDS,RGB,CVBS,SVID}0.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
I have no evidence for this byte being used this way, and lots of
counterexamples. Restore the struct to its empirical definition and
patch up gmbus setup to match.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
I was seeing a nasty 5 frame glitch every 10 seconds, caused by the
poll for connection on DVI attached by SDVO.
As my SDVO DVI supports hotplug detect interrupts, the fix is to
enable them, and hook them in to the various bits of driver
infrastructure so that they work reliably.
Note that this is only tested on single-function DVI-D SDVOs, on two
platforms (965GME and 945GSE), and has not been checked against a
specification document.
With lots of help from Adam Jackson <ajax@redhat.com> on IRC.
Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Various issues involved with the space character were generating
warnings in the checkpatch.pl file. This patch removes most of those
warnings.
Signed-off-by: Akshay Joshi <me@akshayjoshi.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Make the audio property creation routine common and share the single
property between the connectors.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
The ddc proxy depends upon the underlying i2c bus being selected. Under
certain configurations, the i2c-adapter functionality is queried during
initialisation and so may trigger an OOPS during boot. Hence, we need to
reorder the initialisation of the ddc proxy until after we hook up the i2c
adapter for the SDVO device.
The condition under which it fails is when the i2c_add_adapter calls
into i2c_detect which will attempt to probe all valid addresses on the
adapter iff there is a pre-existing i2c_driver with the same class as
the freshly added i2c_adapter.
So it appears to depend upon having compiled in (or loaded such a
module before i915.ko) an i2c-driver that likes to futz over the
i2c_adapters claiming DDC support.
Reported-by: Mihai Moldovan <ionic@ionic.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
* 'intel/drm-intel-next' of ../drm-next: (755 commits)
drm/i915: Only wait on a pending flip if we intend to write to the buffer
drm/i915/dp: Sanity check eDP existence
drm/i915: Rebind the buffer if its alignment constraints changes with tiling
drm/i915: Disable GPU semaphores by default
drm/i915: Do not overflow the MMADDR write FIFO
Revert "drm/i915: fix corruptions on i8xx due to relaxed fencing"
drm/i915: Don't save/restore hardware status page address register
drm/i915: don't store the reg value for HWS_PGA
drm/i915: fix memory corruption with GM965 and >4GB RAM
Linux 2.6.38-rc7
Revert "TPM: Long default timeout fix"
drm/i915: Re-enable GPU semaphores for SandyBridge mobile
drm/i915: Replace vblank PM QoS with "Interrupt-Based AGPBUSY#"
Revert "drm/i915: Use PM QoS to prevent C-State starvation of gen3 GPU"
drm/i915: Allow relocation deltas outside of target bo
drm/i915: Silence an innocuous compiler warning for an unused variable
fs/block_dev.c: fix new kernel-doc warning
ACPI: Fix build for CONFIG_NET unset
mm: <asm-generic/pgtable.h> must include <linux/mm_types.h>
x86: Use u32 instead of long to set reset vector back to 0
...
Conflicts:
drivers/gpu/drm/i915/i915_gem.c
... and fixup some methods to accept the constant argument.
Now that constant module arrays are loaded into read-only memory, using
const appropriately has some benefits beyond warning the programmer
about likely mistakes.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In order to prevent "crushed blacks" on TVs, the range of the RGB output
may be limited to 16-235. This used to be available through Xorg under
the "Broadcast RGB" option, so reintroduce support for KMS.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34543
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Grab the latest stabilisation bits from -fixes and some suspend and
resume fixes from linus.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/i915_irq.c
If the user changes the force-audio property and it no longer reflects
the current configuration, then we need to trigger a mode set in order
to update the registers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If we have an EDID for a digital panel, but we are probing a non-TMDS
connector then we know that this is a false detection, and vice versa.
This should reduce the number of bogus outputs on multi-function
adapters that report the same output on multiple connectors.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34101
Reported-by: Sebastien Caty <sebastien.caty@mrnf.gouv.qc.ca>
Tested-by: Sebastien Caty <sebastien.caty@mrnf.gouv.qc.ca>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
We were not pausing after detecting the response was pending and so did
not allow the hardware sufficient time to complete before aborting. This
lead to transient failures whilst probing SDVO devices.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30235
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Alex Fiestas reported an issue with his HDMI connector being misdetected
as DVI unless he had something connected upon boot. By moving the
decision as to whether to use HDMI or DVI encoding for the HDMI capable
output until we probe the monitor means that we should avoid sending a
HDMI signal to a DVI monitor and also correctly detect hardware like
Alex's.
However, to really determine what connector is soldered onto the wire we
need to inspect the VBT sdvo child devices - but can we trust it?
Reported-by: Alex Fiestas <alex@eyeos.org>
Tested-by: Alex Fiestas <alex@eyeos.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=32828
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
BIOSes. Can't live without them (apparently), definitely can't live with
them.
Reported-by: Ben Gamari <bgamari@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=24312
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Commit d09c23de intended to add a 30ms delay to give the ADD time to
detect any TVs connected. However, it used the sdvo->is_tv flag to do so
which is dependent upon the previous detection result and not whether the
output supports TVs.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
On a few devices, like the Mac Mini, the CRT DDC pins are shared between
the analog connector and the digital connector. In this scenario, rely
on the EDID to determine if a digital panel is connected to the digital
connector.
Reported-and-tested-by: Tino Keitel <tino.keitel@tikei.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As we conflated intel_sdvo->is_hdmi with both having HDMI support on the
ADD along with having HDMI support on the monitor, we would attempt to
use HDMI encodings even if the interface did not support those commands.
Reported-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Reviewed-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
This block is only used when detecting whether the connector is HDMI and
never again, so scope the variable to the detection routine.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This patch enables the sending of AVI infoframes in
drivers/gpu/drm/i915/intel_hdmi.c.
My receiver currently loses sync when the HDMI output on my computer
(DG45FC motherboard) is switched from 800x600 (the BIOS resolution) to
1920x1080 as part of the boot. Fixable by switching inputs on the receiver
a couple of times.
With this patch, my receiver has not lost sync yet (> 40 tries).
Fourth version, now based on drm-intel-next from:
git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel.git
Two questions still remain:
I'm assuming that the sdvo hardware also stores a header ECC byte in
the MSB of the first dword - is this correct?
Does the SDVOB and SDVOC handling in intel_hdmi_set_avi_infoframe()
look correct?
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Allow the user to override the detection of the sink's audio capabilities
from EDID. Not all sinks support the required EDID level to specify
whether they handle audio over the display connection, so allow the user
to enable it manually.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Besides a couple of bugs when writing more than a single byte along the
GMBUS, SDVO was completely failing whilst trying to use GMBUS, so use
bit banging instead.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In the event that the external chipset doesn't implement the
GET_SUPPORTED_ENHANCEMENTS commands, gracefully treat it as having no
enhancments rather than bailing.
Reported-and-tested-by: Woody Suwalski <terraluna977@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=18342
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We weren't unlinking the freed connector from the drm lists, and so
hit some use-after-free if we failed to initialise the connector.
Reported-and-tested-by: Woody Suwalski <terraluna977@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=18342
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Use the GMBUS interface rather than direct bit banging to grab the EDID
over DDC (and for other forms of auxiliary communication with external
display controllers). The hope is that this method will be much faster
and more reliable than bit banging for fetching EDIDs from buggy monitors
or through switches, though we still preserve the bit banging as a
fallback in case GMBUS fails.
Based on an original patch by Jesse Barnes.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Later initialisation of the encoder often requires that
drm_encoder_init() has already been called, for instance, initialiasing
the DDC buses.
Yet another recent regression, as 819f3fb7 depended upon these fixes
which I missed when cherry-picking.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
One problem with devices that share the DDC bus between the VGA and
DVI-I connectors is that with two devices attached we cannot know if
there is truly a monitor attached to the DVI connector. In this case, it
is preferrrable to mark the status as unknown, so that the user can
supply the known set of modes and continue to use the output.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We only need to use the analog encoder for rare devices which share the
DDC between the DVI-I and VGA connectors, so only create as needed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The SDVO proxy i2c adapter wants to be able to use information stored in
the encoder, so pass that through intel_i2c rather than iterate over all
known encoders every time.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
v2: Julien Cristau pointed out that @nondestructive results in
double-negatives and confusion when trying to interpret the parameter,
so use @force instead. Much easier to type as well. ;-)
And fix the miscompilation of vmgfx reported by Sedat Dilek.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Destructive load-detection is very expensive and due to failings
elsewhere can trigger system wide stalls of up to 600ms. A simple
first step to correcting this is not to invoke such an expensive
and destructive load-detection operation automatically.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29536
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16265
Reported-by: Bruno Prémont <bonbons@linux-vserver.org>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The documentation says that an SDVO command takes a maximum of 15us to be
processed by the device, and that it is sufficient to read the status byte
3 times (whilst the command is still in the PENDING state) for the driver
to be confident that sufficient time has elapsed.
We err on the safe side and try 5 times before giving up.
The only question that remains: was the old behaviour derived by
experiments with real hardware?
A look into the murky history of UMS, implies that the behaviour was
accidental and the current retry mechanism was solely designed to catch
the status byte indicating PENDING with no reference to hardware
behaviour. (commit ac9181c014638dbeb334b40b4029d0ccb2b7a0fc in
xf86-video-intel)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Chris Wilson