Fix checkpatch errors of the following type:
* ERROR: "foo * bar" should be "foo *bar"
* ERROR: "(foo*)" should be "(foo *)"
Signed-off-by: Daniel Baluta <dbaluta@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to export this to enable drivers use rt_tos2priority()
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Provide device string properly for USB i2400m wimax devices, also
don't OOPS when providing firmware string. From Phil Sutter.
2) Add support for sh_eth SH7734 chips, from Nobuhiro Iwamatsu.
3) Add another device ID to USB zaurus driver, from Guan Xin.
4) Loop index start in pool vector iterator is wrong causing MAC to not
get configured in bnx2x driver, fix from Dmitry Kravkov.
5) EQL driver assumes HZ=100, fix from Eric Dumazet.
6) Now that skb_add_rx_frag() can specify the truesize increment
separately, do so in f_phonet and cdc_phonet, also from Eric
Dumazet.
7) virtio_net accidently uses net_ratelimit() not only on the kernel
warning but also the statistic bump, fix from Rick Jones.
8) ip_route_input_mc() uses fixed init_net namespace, oops, use
dev_net(dev) instead. Fix from Benjamin LaHaise.
9) dev_forward_skb() needs to clear the incoming interface index of the
SKB so that it looks like a new incoming packet, also from Benjamin
LaHaise.
10) iwlwifi mistakenly initializes a channel entry as 2GHZ instead of
5GHZ, fix from Stanislav Yakovlev.
11) Missing kmalloc() return value checks in orinoco, from Santosh
Nayak.
12) ath9k doesn't check for HT capabilities in the right way, it is
checking ht_supported instead of the ATH9K_HW_CAP_HT flag. Fix from
Sujith Manoharan.
13) Fix x86 BPF JIT emission of 16-bit immediate field of AND
instructions, from Feiran Zhuang.
14) Avoid infinite loop in GARP code when registering sysfs entries.
From David Ward.
15) rose protocol uses memcpy instead of memcmp in a device address
comparison, oops. Fix from Daniel Borkmann.
16) Fix build of lpc_eth due to dev_hw_addr_rancom() interface being
renamed to eth_hw_addr_random(). From Roland Stigge.
17) Make ipv6 RTM_GETROUTE interpret RTA_IIF attribute the same way
that ipv4 does. Fix from Shmulik Ladkani.
18) via-rhine has an inverted bit test, causing suspend/resume
regressions. Fix from Andreas Mohr.
19) RIONET assumes 4K page size, fix from Akinobu Mita.
20) Initialization of imask register in sky2 is buggy, because bits are
"or'd" into an uninitialized local variable. Fix from Lino
Sanfilippo.
21) Fix FCOE checksum offload handling, from Yi Zou.
22) Fix VLAN processing regression in e1000, from Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
sky2: dont overwrite settings for PHY Quick link
tg3: Fix 5717 serdes powerdown problem
net: usb: cdc_eem: fix mtu
net: sh_eth: fix endian check for architecture independent
usb/rtl8150 : Remove duplicated definitions
rionet: fix page allocation order of rionet_active
via-rhine: fix wait-bit inversion.
ipv6: Fix RTM_GETROUTE's interpretation of RTA_IIF to be consistent with ipv4
net: lpc_eth: Fix rename of dev_hw_addr_random
net/netfilter/nfnetlink_acct.c: use linux/atomic.h
rose_dev: fix memcpy-bug in rose_set_mac_address
Fix non TBI PHY access; a bad merge undid bug fix in a previous commit.
net/garp: avoid infinite loop if attribute already exists
x86 bpf_jit: fix a bug in emitting the 16-bit immediate operand of AND
bonding: emit event when bonding changes MAC
mac80211: fix oper channel timestamp updation
ath9k: Use HW HT capabilites properly
MAINTAINERS: adding maintainer for ipw2x00
net: orinoco: add error handling for failed kmalloc().
net/wireless: ipw2x00: fix a typo in wiphy struct initilization
...
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
When using multicast over a local bridge feeding a number of LXC guests
using veth, the LXC guests are unable to get a response from other guests
when pinging 224.0.0.1. Multicast packets did not appear to be getting
delivered to the network namespaces of the guest hosts, and further
inspection showed that the incoming route was pointing to the loopback
device of the host, not the guest. This lead to the wrong network namespace
being picked up by sockets (like ICMP). Fix this by using the correct
network namespace when creating the inbound route entry.
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add #define pr_fmt(fmt) as appropriate.
Add "IPv4: ", "TCP: ", and "IPsec: " to appropriate files.
Standardize on "UDPLite: " for appropriate uses.
Some prefixes were previously "UDPLITE: " and "UDP-Lite: ".
Add KBUILD_MODNAME ": " to icmp and gre.
Remove embedded prefixes as appropriate.
Add missing "\n" to pr_info in gre.c.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a more current kernel messaging style.
Convert a printk block to print_hex_dump.
Coalesce formats, align arguments.
Use %s, __func__ instead of embedding function names.
Some messages that were prefixed with <foo>_close are
now prefixed with <foo>_fini. Some ah4 and esp messages
are now not prefixed with "ip ".
The intent of this patch is to later add something like
#define pr_fmt(fmt) "IPv4: " fmt.
to standardize the output messages.
Text size is trivially reduced. (x86-32 allyesconfig)
$ size net/ipv4/built-in.o*
text data bss dec hex filename
887888 31558 249696 1169142 11d6f6 net/ipv4/built-in.o.new
887934 31558 249800 1169292 11d78c net/ipv4/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we invalidate the inetpeer tree along with the routing cache now,
we don't need a genid to reset the redirect handling when the routing
cache is flushed.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We initialize the routing metrics with the values cached on the
inetpeer in rt_init_metrics(). So if we have the metrics cached on the
inetpeer, we ignore the user configured fib_metrics.
To fix this issue, we replace the old tree with a fresh initialized
inet_peer_base. The old tree is removed later with a delayed work queue.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the future the ipv4/ipv6 route gateway will take on two types
of values:
1) INADDR_ANY/IN6ADDR_ANY, for local network routes, and in this case
the neighbour must be obtained using the destination address in
ipv4/ipv6 header as the lookup key.
2) Everything else, the actual nexthop route address.
So if the gateway is not inaddr-any we use it, otherwise we must use
the packet's destination address.
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/bluetooth/l2cap_core.c
Just two overlapping changes, one added an initialization of
a local variable, and another change added a new local variable.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 2c8cec5c10 (ipv4: Cache learned PMTU information in inetpeer)
removed IP route cache garbage collector a bit too soon, as this gc was
responsible for expired routes cleanup, releasing their neighbour
reference.
As pointed out by Robert Gladewitz, recent kernels can fill and exhaust
their neighbour cache.
Reintroduce the garbage collection, since we'll have to wait our
neighbour lookups become refcount-less to not depend on this stuff.
Reported-by: Robert Gladewitz <gladewitz@gmx.de>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To reflect the fact that a refrence is not obtained to the
resulting neighbour entry.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Roland Dreier <roland@purestorage.com>
If ipv4_valdiate_peer() fails during a cached entry lookup,
we'll NULL derer since the loop iterator assumes rth is not
NULL.
Letting this be handled as a failure is just bogus, so just make it
not fail. If we have trouble getting a non-NULL neighbour for the
redirected gateway, just restore the original gateway and continue.
The very next use of this cached route will try again.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__mkroute_output fails to work with the original tos
and uses value with stripped RTO_ONLINK bit. Make sure we put
the original TOS bits into rt_key_tos because it used to match
cached route.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise we won't notice the peer GENID change.
Reported-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of instantiating an entire new neigh_table instance
just for ATM handling, use the neigh device private facility.
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit f2c31e32b3 (fix NULL dereferences in check_peer_redir()),
dst_get_neighbour() should be guarded by rcu_read_lock() /
rcu_read_unlock() section.
Reported-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now inetpeer is the place where we cache redirect information for ipv4
destinations, we must be able to invalidate informations when a route is
added/removed on host.
As inetpeer is not yet namespace aware, this patch adds a shared
redirect_genid, and a per inetpeer redirect_genid. This might be changed
later if inetpeer becomes ns aware.
Cache information for one inerpeer is valid as long as its
redirect_genid has the same value than global redirect_genid.
Reported-by: Arkadiusz Miśkiewicz <a.miskiewicz@gmail.com>
Tested-by: Arkadiusz Miśkiewicz <a.miskiewicz@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pmtu informations on the inetpeer are visible for output and
input routes. On packet forwarding, we might propagate a learned
pmtu to the sender. As we update the pmtu informations of the
inetpeer on demand, the original sender of the forwarded packets
might never notice when the pmtu to that inetpeer increases.
So use the mtu of the outgoing device on packet forwarding instead
of the pmtu to the final destination.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We move all mtu handling from dst_mtu() down to the protocol
layer. So each protocol can implement the mtu handling in
a different manner.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We plan to invoke the dst_opt->default_mtu() method unconditioally
from dst_mtu(). So rename the method to dst_opt->mtu() to match
the name with the new meaning.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it is, we return null as the default mtu of blackhole routes.
This may lead to a propagation of a bogus pmtu if the default_mtu
method of a blackhole route is invoked. So return dst->dev->mtu
as the default mtu instead.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit f39925dbde (ipv4: Cache learned redirect information in
inetpeer.) introduced a regression in ICMP redirect handling.
It assumed ipv4_dst_check() would be called because all possible routes
were attached to the inetpeer we modify in ip_rt_redirect(), but thats
not true.
commit 7cc9150ebe (route: fix ICMP redirect validation) tried to fix
this but solution was not complete. (It fixed only one route)
So we must lookup existing routes (including different TOS values) and
call check_peer_redir() on them.
Reported-by: Ivan Zahariev <famzah@icdsoft.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we update the learned pmtu informations on demand, we might
report a nagative expiration time value to userspace if the
pmtu informations are already expired and we have not send a
packet to that inetpeer after expiration. With this patch we
send a expire time of null to userspace after expiration
until the next packet is send to that inetpeer.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In func ipv4_dst_check,check_peer_pmtu should be called only when peer is updated.
So,if the peer is not updated in ip_rt_frag_needed,we can not inc __rt_peer_genid.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit f39925dbde
(ipv4: Cache learned redirect information in inetpeer.)
removed some ICMP packet validations which are required by
RFC 1122, section 3.2.2.2:
...
A Redirect message SHOULD be silently discarded if the new
gateway address it specifies is not on the same connected
(sub-) net through which the Redirect arrived [INTRO:2,
Appendix A], or if the source of the Redirect is not the
current first-hop gateway for the specified destination (see
Section 3.3.1).
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
removing obsoleted sysctl,
ip_rt_gc_interval variable no longer used since 2.6.38
Signed-off-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
RCU api had been completed and rcu_access_pointer() or
rcu_dereference_protected() are better than generic
rcu_dereference_raw()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As rt_iif represents input device even for packets
coming from loopback with output route, it is not an unique
key specific to input routes. Now rt_route_iif has such role,
it was fl.iif in 2.6.38, so better to change the checks at
some places to save CPU cycles and to restore 2.6.38 semantics.
compare_keys:
- input routes: only rt_route_iif matters, rt_iif is same
- output routes: only rt_oif matters, rt_iif is not
used for matching in __ip_route_output_key
- now we are back to 2.6.38 state
ip_route_input_common:
- matching rt_route_iif implies input route
- compared to 2.6.38 we eliminated one rth->fl.oif check
because it was not needed even for 2.6.38
compare_hash_inputs:
Only the change here is not an optimization, it has
effect only for output routes. I assume I'm restoring
the original intention to ignore oif, it was using fl.iif
- now we are back to 2.6.38 state
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
compare_keys and ip_route_input_common rely on
rt_oif for distinguishing of input and output routes
with same keys values. But sometimes the input route has
also same hash chain (keyed by iif != 0) with the output
routes (keyed by orig_oif=0). Problem visible if running
with small number of rhash_entries.
Fix them to use rt_route_iif instead. By this way
input route can not be returned to users that request
output route.
The patch fixes the ip_rt_bug errors that were
reported in ip_local_out context, mostly for 255.255.255.255
destinations.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Computers have become a lot faster since we compromised on the
partial MD4 hash which we use currently for performance reasons.
MD5 is a much safer choice, and is inline with both RFC1948 and
other ISS generators (OpenBSD, Solaris, etc.)
Furthermore, only having 24-bits of the sequence number be truly
unpredictable is a very serious limitation. So the periodic
regeneration and 8-bit counter have been removed. We compute and
use a full 32-bit sequence number.
For ipv6, DCCP was found to use a 32-bit truncated initial sequence
number (it needs 43-bits) and that is fixed here as well.
Reported-by: Dan Kaminsky <dan@doxpara.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gergely Kalman reported crashes in check_peer_redir().
It appears commit f39925dbde (ipv4: Cache learned redirect
information in inetpeer.) added a race, leading to possible NULL ptr
dereference.
Since we can now change dst neighbour, we should make sure a reader can
safely use a neighbour.
Add RCU protection to dst neighbour, and make sure check_peer_redir()
can be called safely by different cpus in parallel.
As neighbours are already freed after one RCU grace period, this patch
should not add typical RCU penalty (cache cold effects)
Many thanks to Gergely for providing a pretty report pointing to the
bug.
Reported-by: Gergely Kalman <synapse@hippy.csoma.elte.hu>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt_tos was changed to iph->tos but it must be filtered by RT_TOS
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the future dst entries will be neigh-less. In that environment we
need to have an easy transition point for current users of
dst->neighbour outside of the packet output fast path.
Signed-off-by: David S. Miller <davem@davemloft.net>
It's just taking on one of two possible values, either
neigh_ops->output or dev_queue_xmit(). And this is purely depending
upon whether nud_state has NUD_CONNECTED set or not.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there is a one-to-one correspondance between neighbour
and hh_cache entries, we no longer need:
1) dynamic allocation
2) attachment to dst->hh
3) refcounting
Initialization of the hh_cache entry is indicated by hh_len
being non-zero, and such initialization is always done with
the neighbour's lock held as a writer.
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of all of the useless and costly indirection
by doing the neigh hash table lookup directly inside
of the neighbour binding.
Rename from arp_bind_neighbour to rt_bind_neighbour.
Use new helpers {__,}ipv4_neigh_lookup()
In rt_bind_neighbour() get rid of useless tests which
are never true in the context this function is called,
namely dev is never NULL and the dst->neighbour is
always NULL.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the case labels the same indent as the switch.
git diff -w shows no difference.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Baluta