Move try_module_get() call into spin protected block to prevent zcrypt
driver module unload while submitting a request to driver.
Signed-off-by: Ralph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
AP bus module uses bus_for_each_dev() in software interrupt context to
poll for completed requests which might cause dead locks. Solution: use
private AP device list for polling in software interrupt context.
Signed-off-by: Ralph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make sure set_slsb problems are handled correctly in
qdio_do_qdio_fill_input() and qdio_do_qdio_fill_output.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch (as868) adds a helper routine for device drivers that need
to set up a callback to perform some action in a different process's
context. This is intended for use by attribute methods that want to
unregister themselves or their parent device. Attribute method calls
are mutually exclusive with unregistration, so such actions cannot be
taken directly.
Two attribute methods are converted to use the new helper routine: one
for SCSI device deletion and one for System/390 ccwgroup devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The subchannel may just be status pending, even with actl == 0. We
must go through the cancel_halt_clear procedure to put the subchannel
into a defined state.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After I/O has been killed by the common I/O layer, trigger path
verification which will queue cio_device_nopath_notify itself if it
finds a device to be without paths.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make sure we hold the device lock when we modify the ccw device
structure but always call the notify function without the lock held.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For extended error reporting we sometimes have to start an
Sense Subsystem Status request (SNSS). When this request needs
to be recovered for some reason, the recovery request will
fail with 'command reject'.
Our usual recovery procedure will retry the failed request by
creating a new request and chaining the failed request from that
one. SNSS requests, though, must not be chained from anything,
so the recovery request will fail permanently.
Use the default recovery for SNSS request, which will just restart
the original request without further ado.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After switching compression on/off with the mt command, tape encryption is no
longer working. The reason for that is, that the modeset_byte is set to
the compression value instead of using bitwise and/or bit operations to
enable/disable the corresponding bit.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch splits the vlan_group struct into a multi-allocated struct. On
x86_64, the size of the original struct is a little more than 32KB, causing
a 4-order allocation, which is prune to problems caused by buddy-system
external fragmentation conditions.
I couldn't just use vmalloc() because vfree() cannot be called in the
softirq context of the RCU callback.
Signed-off-by: Dan Aloni <da-x@monatomic.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With CONFIG_SHARED_KERNEL the kernel text segment that might be in a
read only memory sections starts at 1MB. Memory between 0x12000 and
0x100000 is unused then. Free this, so we have appr. an extra MB
of memory available.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Setup.h has been misused for ipl related stuff in the past. We now move
everything, which has to do with ipl and reipl to a new header file named
"ipl.h".
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix compile of sclp_quiesce for CONFIG_SMP=n.
Signed-off-by: Jan Glauber <jan.glauber@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] remove __io_virt and mmiowb.
[S390] cio: use ARRAY_SIZE in device_id.c
[S390] cio: Fixup interface for setting options on ccw devices.
[S390] smp_call_function/smp_call_function_on locking.
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The current ccw_device_set_options() sets a specified mask of options
and clears those not specified, but there is no way to find out which
options have already been set.
In order to fix this up, introduce the following interface changes:
ccw_device_set_options() now only sets the specified bits, but does
not clear those that are not specified.
ccw_device_clear_options() clears the specified bits.
ccw_device_set_options_mask() provides the old semantics (setting only
the specified bits and clearing the others).
Device drivers now work as expected. qdio has been adapted.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (97 commits)
[SCSI] zfcp: removed wrong comment
[SCSI] zfcp: use of uninitialized variable
[SCSI] zfcp: Invalid locking order
[SCSI] aic79xx: use dma_get_required_mask()
[SCSI] aic79xx: fix bracket mismatch in unused macro
[SCSI] BusLogic: Replace 'boolean' by 'bool'
[SCSI] advansys: clean up warnings
[SCSI] 53c7xx: brackets fix in uncompiled code
[SCSI] nsp_cs: remove old scsi code
[SCSI] aic79xx: make ahd_match_scb() static
[SCSI] DAC960: kmalloc->kzalloc/Casting cleanups
[SCSI] scsi_kmap_atomic_sg(): check that local irqs are disabled
[SCSI] Buslogic: local_irq_disable() is redundant after local_irq_save()
[SCSI] aic94xx: update for v28 firmware
[SCSI] scsi_error: Fix lost EH commands
[SCSI] aic94xx: Add default bus reset handler
[SCSI] aic94xx: Remove TMF result code munging
[SCSI] libsas: Add an LU reset mechanism to the error handler
[SCSI] libsas: Don't BUG when connecting two expanders via wide port
[SCSI] st: fix Tape dies if wrong block size used, bug 7919
...
Replace a small number of expressions with a call to the "container_of()"
macro.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bug: pnx8550 code creates directory but resets ->nlink to 1.
create_proc_entry() et al will correctly set ->nlink for you.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Invalid locking order. Kernel hangs after trying to take two locks
which are dependend on each other. Introducing temporary variable
to free requests. Free lock after requests are copied.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adapt special message interface to new IUCV API
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapt netiucv network device driver to new IUCV API
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapt vmlogrdr character device driver to new IUCV API
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapt monreader character device driver to new IUCV API
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the old IUCV code from drivers/s390/net
Remove approprirate IUCV entries from drivers/s390/net/Makefile,
drivers/s390/net/Kconfig and arch/s390/defconfig
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hopefully this will make it more maintainable and less error prone.
Code makes use of search_exception_tables(). Since it calls this
function before the kernel exeception table is sorted, there is an
early call to sort_main_extable().
This way it's easy to use the already present infrastructure of fixup
sections. Also this would allows to easily convert the rest of
head[31|64].S into C code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Preset the bogomips number to the cpu capacity value reported by
store system information in SYSIB 1.2.2. This value is constant
for a particular machine model and can be used to determine
relative performance differences between machines.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
3592 tape devices are able to write data encrpyted on tape mediums.
This z/Linux device driver support includes the following functions:
* ioctl to switch on/off encryption
* ioctl to query encryption status of drive
* ioctls to set and query key encrypting keys (kekls)
* long busy interrupt handling
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch adds support for clock synchronization to an external time
reference (ETR). The external time reference sends an oscillator
signal and a synchronization signal every 2^20 microseconds to keep
the TOD clocks of all connected servers in sync. For availability
two ETR units can be connected to a machine. If the clock deviates
for more than the sync-check tolerance all cpus get a machine check
that indicates that the clock is out of sync. For the lovely details
how to get the clock back in sync see the code below.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Lower priority of "Blacklisted device detected" messages so we don't
overwrite more useful messages.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Change CHSC event handling to be more easily extensible.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If we have a subchannel id which has been generated via
for_each_subchannel(), it might contain an invalid subchannel set id.
We need to catch the ensuing operand exception by using stsch_err()
instead of stsch() in all possible cases.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The reserve/release IOCTLs sometimes do not work. If second system
does a 'steal lock' the pending unit check (Format 3 Msg F) is
delivered. Since ERP is disabled for reserve/release, the IOCTL call
fails. We have to allow basic ERP (retries) for reserve/release IOCTLs.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Logging of relevant information is already done by disciplines
dump_sense function.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
cpu_relax() has barrier() semantics hence there is no need to use both
of them in conjunction in sclp_sync_wait(). Also change cpu_relax()
so it's more obvious that it has barrier semantics.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Create/remove the channel measurement binary files with
device_{create,remove}_bin_file instead of sysfs_{create,remove}_bin_file.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
local_bh_disable/_local_bh_enable must not be called if in_irq() is
true. Besides that if in_interrupt() is true bottom halves are
disabled anyway.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently loaded DCSS segments are now listed in /proc/iomem with
their name followed by a trailing "(DCSS)".
Signed-off-by: Gerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If we try to start path verification when an unsolicited interrupt
is already pending, stctl shows status pending and we delay path
verification again. We need to check for the doverify bit when the
unsolicited interrupt comes in and then do path verification.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The initialization of the dasd_eer code is one of the last steps of the
dasd driver initialization. When initialization fails in one of the
earlier steps, the dasd_exit function is called to clean up what has been
done so far. So the dasd_eer_exit function may be called, although the
dasd_eer_init function wasn't called before and dasd_eer_exit tries to
unregister a misc device that wasn't registered, which results in a BUG.
Make sure that dasd_eer_exit can be called without initialization. Use a
dynamically allocated struct miscdevice instead of a static one, so we
only try to unregister the device if it exists and was actually registered.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Requests are aborted when the sclp interface reports 'not operational'
even though they may still be active at the sclp, leading to concurrent
writes to request memory by both the kernel and the sclp interface.
Do not abort requests for which the sclp interface reports not
operational status during request retry.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>5A
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Since ssd_info is now available before the subchannel is registered,
we don't need to check whether it is available.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Changeset 740b5706b9 moved the protecting
spinlock from __cpcmd to cpcmd. Therefore vmcp can no longer use __cpcmd,
instead we have to use cpcmd.
Signed-off-by: Christian Borntraeger <cborntra@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use barrier() in stsch_reset() instead of duplicating the stsch()
inline assembly and adding "memory" to the clobberlist.
Pointed out by Chuck Ebbert.
Real fix would be to add a fixup section to the stsch() and extend the
basic program check handler so it searches the exception tables in case
of a program check.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
[PATCH 4/5] s390: iucv Kconfig help description changes
From: Ursula Braun <braunu@de.ibm.com>
remove text from help description which does not
apply anymore for 2.6 kernel series.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- qeth device functions were not callable
in atomic context due to usage of wait_event_xxx operations in qeth.
"schedule while atomic" message appeared and kernel dumped when
removing slave from bond device.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- packet socket support is not complete.
Recvfrom a packet socket does not fill the sockaddr_ll structure.
device function hard_header_parse is not implemented.
For layer 2 mode and layer 3 mode with fake_ll turned on, we have
the information to fill sockaddr_ll.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Ursula Braun <braunu@de.ibm.com>
- VLAN header reordering did not work on packets
received through qeth interface in layer 2 mode.
This caused dhcpcd not to work with VLAN devices.
- set qeth performance statistics initally inactive
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
[patch] qeth: fix uaccess handling and get rid of unused variable
drivers/s390/net/qeth_main.c: In function `qeth_process_inbound_buffer':
drivers/s390/net/qeth_main.c:2563: warning: unused variable `vlan_addr'
include/asm/uaccess.h: In function `qeth_do_ioctl':
drivers/s390/net/qeth_main.c:4847: warning:
ignoring return value of `copy_to_user'
drivers/s390/net/qeth_main.c:4849: warning:
ignoring return value of `copy_to_user'
drivers/s390/net/qeth_main.c:4996: warning:
ignoring return value of `copy_to_user'
Cc: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Copy inline assembly of stsch and add "memory" to clobber list in order
to prevent gcc from optimizing away the checking of the global variable
"pgm_check_occured".
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reduce the max. buffer size for the monwriter device to prevent a
possible problem with the z/VM monitor service.
Signed-off-by: Melissa Howland <melissah@us.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Asynchronous probe can release memory of a subchannel before
css_get_ssd_info is called. To fix this call css_get_ssd_info
before registering with driver core.
Signed-off-by: Stefan Bader <shbader@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reboot hangs on LPARs without diag308 support. The reason for this is,
that before the reboot is done, the channel subsystem is shut down.
During the reset on each possible subchannel a "store subchannel" is
done. This operation can end in a program check interruption, if the
specified subchannel set is not implemented by the hardware. During
the reset, currently we do not have a program check handler, which
leads to the described kernel bug. We install now a new program check
handler for the reboot code to fix this problem.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
sclp_cpi is GPL. Make the module not taint the kernel
Signed-off-by: Christian Borntraeger <cborntra@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add code to reset all queues for a domain and add missing tasklet_kill
call to ap bus module exit code.
Signed-off-by: Ralph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
A HiperSocket multicast queue works asynchronously. When sending
buffers, the buffer state change from PRIMED to EMPTY may happen
delayed. Reschedule the checking for changes in the outbound queue,
if there are still PRIMED buffers.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Run this:
#!/bin/sh
for f in $(grep -Erl "\([^\)]*\) *k[cmz]alloc" *) ; do
echo "De-casting $f..."
perl -pi -e "s/ ?= ?\([^\)]*\) *(k[cmz]alloc) *\(/ = \1\(/" $f
done
And then go through and reinstate those cases where code is casting pointers
to non-pointers.
And then drop a few hunks which conflicted with outstanding work.
Cc: Russell King <rmk@arm.linux.org.uk>, Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Steven French <sfrench@us.ibm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] Poison init section before freeing it.
[S390] Use add_active_range() and free_area_init_nodes().
[S390] Virtual memmap for s390.
[S390] Update documentation for dynamic subchannel mapping.
[S390] Use dev->groups for adding/removing the subchannel attribute group.
[S390] Support for disconnected devices reappearing on another subchannel.
[S390] subchannel lock conversion.
[S390] Some preparations for the dynamic subchannel mapping patch.
[S390] runtime switch for qdio performance statistics
[S390] New DASD feature for ERP related logging
[S390] add reset call handler to the ap bus.
[S390] more workqueue fixes.
[S390] workqueue fixes.
[S390] uaccess_pt: add missing down_read() and convert to is_init().
This is the grungy swap all the occurrences in the right places patch that
goes with the updates. At this point we have the same functionality as
before (except that sgttyb() returns speeds not zero) and are ready to
begin turning new stuff on providing nobody reports lots of bugs
If you are a tty driver author converting an out of tree driver the only
impact should be termios->ktermios name changes for the speed/property
setting functions from your upper layers.
If you are implementing your own TCGETS function before then your driver
was broken already and its about to get a whole lot more painful for you so
please fix it 8)
Also fill in c_ispeed/ospeed on init for most devices, although the current
code will do this for you anyway but I'd like eventually to lose that extra
paranoia
[akpm@osdl.org: bluetooth fix]
[mp3@de.ibm.com: sclp fix]
[mp3@de.ibm.com: warning fix for tty3270]
[hugh@veritas.com: fix tty_ioctl powerpc build]
[jdike@addtoit.com: uml: fix ->set_termios declaration]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Peter Oberparleiter <oberpar@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the locking of signal->tty.
Use ->sighand->siglock to protect ->signal->tty; this lock is already used
by most other members of ->signal/->sighand. And unless we are 'current'
or the tasklist_lock is held we need ->siglock to access ->signal anyway.
(NOTE: sys_unshare() is broken wrt ->sighand locking rules)
Note that tty_mutex is held over tty destruction, so while holding
tty_mutex any tty pointer remains valid. Otherwise the lifetime of ttys
are governed by their open file handles. This leaves some holes for tty
access from signal->tty (or any other non file related tty access).
It solves the tty SLAB scribbles we were seeing.
(NOTE: the change from group_send_sig_info to __group_send_sig_info needs to
be examined by someone familiar with the security framework, I think
it is safe given the SEND_SIG_PRIV from other __group_send_sig_info
invocations)
[schwidefsky@de.ibm.com: 3270 fix]
[akpm@osdl.org: various post-viro fixes]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Roland McGrath <roland@redhat.com>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: James Morris <jmorris@namei.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Jan Kara <jack@ucw.cz>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- create a 'pseudo_subchannel' per channel subsystem (the 'orphanage')
- use the orphanage as a shelter for ccw_devices that can't remain on the same
subchannel
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Convert the subchannel lock to a pointer to a lock. Needed for the dynamic
subchannel mapping patch.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove CONFIG_QETH_PERF_STATS and use a sysfs attribute instead.
We want to have the ability to turn the statistics on/off at runtime.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It is now possible to enable/disable ERP related logging without re-compile
and re-ipl. A additional sysfs-attribute 'erplog' allows to switch the
logging non-interruptive.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_DMA is an alias of GFP_DMA. This is the last one so we
remove the leftover comment too.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_ATOMIC is an alias of GFP_ATOMIC
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In io_subchannel_register(), it is better to just reprobe the current
device if it hasn't a driver yet than to rescan the whole bus.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If I/O was running on a just varied off chpid, it will be terminated.
If this was a common I/O layer internal I/O, it needs to be retried.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the last path to a device is gone after a chpid has been varied
off, putting it on the slow queue doesn't prevent a device driver
from still attempting to use it (it may stay on the slow queue for a
long time). Instead, trigger a verify event which will prevent I/O
attempts from the device driver immediately.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add some prefixes to constands defined in drivers/s390/net/qdio.h
and drivers/s390/lcs.h to make it possible to include the three
header files drivers/s390/net/qeth.h, drivers/s390/net/qdio.h and
drivers/net/s390/lcs.h in one C file. This is required for the
patch that generates the kerntypes.o file for use by lcrash.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Let one master cpu kill all other cpus instead of sending an external
interrupt to all other cpus so they can kill themselves.
Simplifies reipl/shutdown functions a lot.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case of re-IPL and diag308 doesn't work we have to reset all devices
manually and wait synchronously that each reset finished.
This patch adds the necessary infrastucture and the first exploiter of it.
Subsystems that need to add a function that needs to be called at re-IPL
may register/unregister this function via
struct reset_call {
struct reset_call *next;
void (*fn)(void);
};
void register_reset_call(struct reset_call *reset);
void unregister_reset_call(struct reset_call *reset);
When the registered function get called the context is:
- all cpus beside the current one are stopped
- all machine checks and interrupts are disabled
- prefixing is disabled
- a default machine check handler is available for use
The registered functions may not take any locks are sleep.
For the common I/O layer part of this patch:
Introduce a reset_call css_reset that does the following:
- clear all subchannels
- perform a rchp on all channel paths and wait for the resulting
machine checks
This replaces the calls to clear_all_subchannels() and
cio_reset_channel_paths() for kexec and ccw reipl. reipl_ccw_dev() now
uses reipl_find_schid() to determine the subchannel id for a given
device id.
Also remove cio_reset_channel_paths() and friends since they are not
needed anymore.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently the return value of 'dasd_eer_enable' is returned - even if the
function returned '0'. Now return 'count' for successful execution.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case a request timed out and termination did not work, the console was
flooded with retry messages (every 1/10s). Now we use a 5s delay per retry and
generate a more precise message.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove lock pointer from 3215 device structure. Use get_ccwdev_lock
for each use of the lock in the ccw-device structure.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When writing to dasd attributes (e.g. readonly), all values besides '1'
are handled like '0'.
Other sysfs-attributes like 'online' are checking for '1' and for '0'
and do not accept other values. Therefore enhanced checking and error
handling in dasd_devmap attribute store functions.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix various .c/.h typos in comments (no code changes).
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
ccw_device_register() is only called from io_subchannel_register()
and io_subchannel_probe() and will never be called for possible
non-io subchannels.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Added a call to device_unregister() in ap_scan_bus() to actively
remove unavailable AP bus devices with every bus scan. Previously
devices were only removed in ap_queue_message() or __ap_poll_all().
Signed-off-by: Ralph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move css_probe_device() behind giving up the lock for the old subchannel
in css_evaluate_known_subchannel() so we aren't disabled when we call it.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Clean up dasd timer when when a dasd device is set offline.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reset device operational notification flag when channel paths become
unavailable during path verification.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The grace period handling introduced needless complexity. It didn't
help the dasd driver (which can handle terminated I/O just well),
and it doesn't help for long running channel programs (which won't
complete during the grace period anyway). Terminating I/O using a
path that just disappeared immediately is much more consistent with
what the user expects.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use the proper structures to identify device and subchannel. Change
get_disc_ccwdev_by_devno() to get_disc_ccwdev_by_dev_id().
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix length on kzalloc for data buffer so as to not overwrite
unallocated storage.
Signed-off-by: Melissa Howland <melissah@us.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the last few places where a pointer to pt_regs gets passed.
Also make sure we call set_irq_regs() before irq_enter() and after
irq_exit(). This doesn't fix anything but makes sure s390 looks the
same like all other architectures.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In order to determine chpid validity, we need to check whether the
corresponding path is specified in the pim.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make max_bufs a global (per linux guest) limit.
Signed-off-by: Melissa Howland <melissah@us.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The ap bus is supposed to have a low priority. We must use 19 instead
of -20, which is just the opposite.
Signed-off-by: Christian Borntraeger <cborntra@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Retry internal operation after unit check instead of aborting them.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add timeout handler for common-I/O-layer-internal I/O operations.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix a race condition during AP device registration and unregistration.
Signed-off-by: Ralph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
While the machine owns us an interrupt in these cases (and we should get
one), reality isn't always like that...
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There are a few places in the kernel where the init task is signaled. The
ctrl+alt+del sequence is one them. It kills a task, usually init, using a
cached pid (cad_pid).
This patch replaces the pid_t by a struct pid to avoid pid wrap around
problem. The struct pid is initialized at boot time in init() and can be
modified through systctl with
/proc/sys/kernel/cad_pid
[ I haven't found any distro using it ? ]
It also introduces a small helper routine kill_cad_pid() which is used
where it seemed ok to use cad_pid instead of pid 1.
[akpm@osdl.org: cleanups, build fix]
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replaces the pid_t value with a struct pid to avoid pid wrap around
problems.
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As part of an SMP cleanliness pass over UML, I consted a bunch of
structures in order to not have to document their locking. One of these
structures was a struct tty_operations. In order to const it in UML
without introducing compiler complaints, the declaration of
tty_set_operations needs to be changed, and then all of its callers need to
be fixed.
This patch declares all struct tty_operations in the tree as const. In all
cases, they are static and used only as input to tty_set_operations. As an
extra check, I ran an i386 allyesconfig build which produced no extra
warnings.
53 drivers are affected. I checked the history of a bunch of them, and in
most cases, there have been only a handful of maintenance changes in the
last six months. serial_core.c was the busiest one that I looked at.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
All on stack DECLARE_COMPLETIONs should be replaced by:
DECLARE_COMPLETION_ONSTACK
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make it possible to disable the block layer. Not all embedded devices require
it, some can make do with just JFFS2, NFS, ramfs, etc - none of which require
the block layer to be present.
This patch does the following:
(*) Introduces CONFIG_BLOCK to disable the block layer, buffering and blockdev
support.
(*) Adds dependencies on CONFIG_BLOCK to any configuration item that controls
an item that uses the block layer. This includes:
(*) Block I/O tracing.
(*) Disk partition code.
(*) All filesystems that are block based, eg: Ext3, ReiserFS, ISOFS.
(*) The SCSI layer. As far as I can tell, even SCSI chardevs use the
block layer to do scheduling. Some drivers that use SCSI facilities -
such as USB storage - end up disabled indirectly from this.
(*) Various block-based device drivers, such as IDE and the old CDROM
drivers.
(*) MTD blockdev handling and FTL.
(*) JFFS - which uses set_bdev_super(), something it could avoid doing by
taking a leaf out of JFFS2's book.
(*) Makes most of the contents of linux/blkdev.h, linux/buffer_head.h and
linux/elevator.h contingent on CONFIG_BLOCK being set. sector_div() is,
however, still used in places, and so is still available.
(*) Also made contingent are the contents of linux/mpage.h, linux/genhd.h and
parts of linux/fs.h.
(*) Makes a number of files in fs/ contingent on CONFIG_BLOCK.
(*) Makes mm/bounce.c (bounce buffering) contingent on CONFIG_BLOCK.
(*) set_page_dirty() doesn't call __set_page_dirty_buffers() if CONFIG_BLOCK
is not enabled.
(*) fs/no-block.c is created to hold out-of-line stubs and things that are
required when CONFIG_BLOCK is not set:
(*) Default blockdev file operations (to give error ENODEV on opening).
(*) Makes some /proc changes:
(*) /proc/devices does not list any blockdevs.
(*) /proc/diskstats and /proc/partitions are contingent on CONFIG_BLOCK.
(*) Makes some compat ioctl handling contingent on CONFIG_BLOCK.
(*) If CONFIG_BLOCK is not defined, makes sys_quotactl() return -ENODEV if
given command other than Q_SYNC or if a special device is specified.
(*) In init/do_mounts.c, no reference is made to the blockdev routines if
CONFIG_BLOCK is not defined. This does not prohibit NFS roots or JFFS2.
(*) The bdflush, ioprio_set and ioprio_get syscalls can now be absent (return
error ENOSYS by way of cond_syscall if so).
(*) The seclvl_bd_claim() and seclvl_bd_release() security calls do nothing if
CONFIG_BLOCK is not set, since they can't then happen.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Right now ->flags is a bit of a mess: some are request types, and
others are just modifiers. Clean this up by splitting it into
->cmd_type and ->cmd_flags. This allows introduction of generic
Linux block message types, useful for sending generic Linux commands
to block devices.
Signed-off-by: Jens Axboe <axboe@suse.de>
argument and inferred net-endian variables in callers annotated.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Major cleanup of all s390 inline assemblies. They now have a common
coding style. Quite a few have been shortened, mainly by using register
asm variables. Use of the EX_TABLE macro helps as well. The atomic ops,
bit ops and locking inlines new use the Q-constraint if a newer gcc
is used. That results in slightly better code.
Thanks to Christian Borntraeger for proof reading the changes.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Call init_timer only once fpr tp->timer in tty3270.
Signed-off-by: Jan Glauber <jan.glauber@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix the fix ... One of my previous fixes introduced removal of all fsf
requests in zfcp's eh_host_reset_handler. But this must not happen
before qdio queues are shut down. So, I revert the changes of
zfcp_scsi_eh_host_reset_handler.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This instance will be used whenever a timer is needed for
a request by zfcp.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
zfcp's eh_abort_handler used the wrong request ID to
identify the request to be aborted. The bug was introduced
with commit fea9d6c7bc
for improved management of request IDs. The bug is
fixed with this patch.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Create private slab caches in order to guarantee proper alignment of
data structures that get passed to hardware.
Sidenote: with this patch slab cache debugging will finally work on s390
(at least no known problems left).
Furthermore this patch does some minor cleanups:
- store ptr for transport template in struct zfcp_data
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Compile fix ups and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
css_evaluate_subchannel() operates subchannel without lock which can
lead to erratic behavior caused by concurrent device access. Also
split evaluation function to make it more readable.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reappearing channel paths are sometimes not utilized by CCW devices
because path verification incorrectly relies on path-operational-mask
information which is not updated until a channel path has been used
again.
Modify path verification procedure to always query all available paths
to a device.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
CHPIDs that are logically varied off will not be removed from
a CCW device's path group because resign-from-pathgroup command is
issued with invalid path mask of 0 because internal CCW operations
are masked by the logical path mask after the relevant bits are
cleared by the vary operation.
Do not apply logical path mask to internal operations.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Subchannel may incorrectly remain in state no-path after channel paths
have reappeared. Currently the scan for subchannels which are using a
channel path ends at the first occurrence if a full link address was
provided by the channel subsystem. The scan needs to continue over
all subchannels.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Specifying kernel parameter "dasd=nopav" on systems running under VM
has no function but results in message "disable PAV mode". Correct
message is "'nopav' not supported on VM".
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add the MODALIAS environment variable for ccw bus uevents.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch delivers a new Linux API in the form of a misc char
device that is useable from user space and allows write access
to the z/VM APPLDATA Monitor Records collected by the *MONITOR
System Service of z/VM.
Signed-off-by: Melissa Howland <melissah@us.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The xpram driver shows and uses 4096 bytes less than available.
Signed-off-by: Christian Borntraeger <cborntra@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix comment typo in vmcp, it is z/VM and not v/VM.
Signed-off-by: Christian Borntraeger <cborntra@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The last SLSB has to be set to STATE_PROCESSING if we really want to
use the PROCESSING feature.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Previous patch that was intended to reduce stack usage within common
i/o layer didn't consider implicit memset(..., 0, ...) used with the
initializations used before.
Add these missing memsets wherever it's not obvious that the
concerned memory region is zeroed. This should give the same semantics
as before.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Convert GET_IPL_DEVICE assembler macro to C function.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With System z9 additional fields have been added to the output of the
store system information instruction. This patch adds the new model
information field and the alternate cpu capability fields to the
output of /proc/sysinfo. While we at it clean up the code as well.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Enhanced default DBF level to get most important messages
in debug feature files.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The dasd_device_from_cdev function is called from interrupt context
to get the struct dasd_device associated with a ccw device. The
driver_data of the ccw device points to the dasd_devmap structure
which contains the pointer to the dasd_device structure. The lock
that protects the dasd_devmap structure is acquire with out irqsave.
To prevent the deadlock in dasd_device_from_cdev if it is called
from interrupt context the dependency to the dasd_devmap structure
needs to be removed. Let the driver_data of the ccw device point
to the dasd_device structure directly and use the ccw device lock
to protect the access.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
qdio_get_micros is supposed to return microseconds. The get_clock()
return value needs to be shifted by 12 to get to microseconds.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use do { } while (0) constructs instead of empty defines to avoid
subtle compile bugs.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It is now possible to specify a ccw/fcp dump device which is used to
automatically create a system dump in case of a kernel panic. The dump
device can be configured under /sys/firmware/dump.
In addition it is now possible to specify a ccw/fcp device which is used
for the next reboot of Linux. The reipl device can be configured under
/sys/firmware/reipl.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Allow the user space to send extended cprb messages directly to the
PCIXCC / CEX2C cards. This allows the CCA library to construct special
crypto requests that use "secure" keys that are stored on the card.
Signed-off-by: Ralph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The Makefile and Kconfig changes should be obvious. The monolithic
build option is there to create an old-style z90crypt module for
backward compatability to older distributions.
Signed-off-by: Ralph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The user space interface of the zcrypt device driver implements the old
user space interface as defined by the old z90crypt driver. Everything
is there, the /dev/z90crypt misc character device, all the lovely ioctls
and the /proc file. Even writing to the z90crypt proc file to configure
the crypto device still works. It stands to reason to remove the proc
write function someday since a much cleaner configuration via the sysfs
is now available.
The ap bus device drivers register crypto cards to the zcrypt user
space interface. The request router of the user space interface
picks one of the registered cards based on the predicted latency
for the request and calls the driver via a callback found in the
zcrypt_ops of the device. The request router only knows which
operations the card can do and the minimum / maximum number of bits
a request can have.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Ralph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a bus for the adjunct processor interface. Up to 64 devices can
be connect to the ap bus interface, each device with 16 domains. That
makes 1024 message queues. The interface is asynchronous, the answer
to a message sent to a queue needs to be received at some later point
in time. Unfortunately the interface does not provide interrupts when
a message reply is pending. So the ap bus needs to implement some
fancy polling, each active queue is polled once per 1/HZ second or
continuously if an idle cpus exsists and the poll thread is activ
(see poll_thread parameter).
The ap bus uses the sysfs path /sys/bus/ap and has two bus attributes,
ap_domain and config_time. The ap_domain selects one of the 16 domains
to be used for this system. This limits the maximum number of ap devices
to 64. The config_time attribute contains the number of seconds between
two ap bus scans to find new devices.
The ap bus uses the modalias entries of the form "ap:tN" to autoload
the ap driver for hardware type N. Currently known types are:
3 - PCICC, 4 - PCICA, 5 - PCIXCC, 6 - CEX2A and 7 - CEX2C.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Ralph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The z90crypt driver has served its term. It is replaced by the shiny
new zcrypt device driver.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
[PATCH 9/9] s390: qeth driver fixes [6/6]
From: Frank Pavlic <fpavlic@de.ibm.com>
- Hipersockets has no IPV6 support, thus prevent issueing
SETRTG_IPV6 control commands on Hipersockets devices.
- fixed error handling in qeth_sysfs_(un)register
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
[PATCH 8/9] s390: qeth driver fixes [5/6]
From: Frank Pavlic <fpavlic@de.ibm.com>
fix kernel panic in qdio queue handling.
qeth_qdio_clear_card() could be invoked by 2 CPUs
simultaneously (for example reboot event and recovery).
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
[PATCH 7/9] s390: qeth driver fixes [4/6]
From: Frank Pavlic <fpavlic@de.ibm.com>
- fix kernel crash due to race,
set card->state to SOFTSETUP after
card and card->dev are initialized properly.
- remove CONFIG_QETH_PERF_STATS, use sysfs attribute instead,
as we want to have the ability to turn on/off the
statistics at runtime.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
[PATCH 6/9] s390: qeth driver fixes [3/6]
From: Frank Pavlic <fpavlic@de.ibm.com>
fixed kernel panic caused by qeth driver:
Using a bonding device qeth driver will realloc
headroom for every skb coming from the bond device.
Once this happens qeth frees the original skb and
set the skb pointer to the new realloced skb.
Under heavy transmit workload (e.g.UDP streams) through bond
network device the qdio output queue might get full.
In this case we return with EBUSY from qeth_send_packet.
Returning to qeth_hard_start_xmit routine
the skb address on the stack still points to the old address,
which has been freed before.
Returning from qeth_hard_start_xmit with EBUSY results in
requeuing the skb. In this case it corrupts the qdisc queue
and results in kernel panic.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
[PATCH 5/9] s390: qeth driver fixes [2/6]
From: Frank Pavlic <fpavlic@de.ibm.com>
- fixed error handling in create_device_attributes
- fixed some minor bugs in IPv4
and IPv6 address checking
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
[PATCH 4/9] s390: qeth driver fixes [1/6]
From: Frank Pavlic <fpavlic@de.ibm.com>
- Drop incoming packets with vlan_tag set
if card->vlangrp is not set.
- use always vlan_hwaccel_rx to pass
vlan frames to the stack.
- fix recovery problem. Device was recovered
properly but still not working.
netif_carrier_on call right before
recovery start fixes it.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
[PATCH 3/9] s390: Makefile cleanup
From: Frank Pavlic <fpavlic@de.ibm.com>
remove CONFIG_MPC from Makefile which was
introduced accidently in the past.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
[PATCH 2/9] s390: netiucv driver fixes
From: Frank Pavlic <fpavlic@de.ibm.com>
- missing lock initialization added
- avoid duplicate iucv-interfaces to the same peer
- rw-lock added for manipulating the list of
defined iucv connections
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hi Jeff,
this is a RESEND of the nine s390 network driver patches.
I finally found that my kmail corrupted almost every patch
I sent the last time. Please apply these 9 patches and forget
about my first attempt! Sorry for the delay, I had some fights
with sendmail, IMAP and mutt configuration.
Frank
[RESEND PATCH 1/9] s390: minor s390 network driver fixes
From: Frank Pavlic <fpavlic@de.ibm.com>
- iucv driver:
use do { } while (0) constructs
instead of empty defines to avoid compile bugs.
- ctc driver:
missing lock initialization added
- lcs driver:
BUG_ON usage was removed accidently
with the last lcs patch.
Put them back in place.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Calls to set a device online with path grouping may get stuck in
some cases because certain device conditions where discarded after
unsolicited interrupts.
Check subchannel activity after unsolicited interrupts and retry
the operation if the subchannel is idle.
Signed-off-by: Stefan Bader <shbader@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Devices enter no-path state after disabling a channel path
via the SE even though another path has been reenabled at the SE.
The devices are set into no-path state before triggering path
verification even though other paths may have become available.
To fix this trigger path verification before setting a device into
no-path state.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use different kind of assignment to make sure gcc doesn't create code
that creates temp variables on the stack, assigns values to it and
copies the content of the whole temp variable to the destination.
This reduces stack usage of e.g. ccwgroup_driver_register from 976
to 48 bytes instead.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix clear_IO handling (need to wait for interrupt) and
introduced error-handling in shutdown processing.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The subsystem check in the PAV code is incorrect, it enables PAV
per device instead of per subsystem.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
qeth: bhs must be disabled when accessing neighbour tables.
=================================
[ INFO: inconsistent lock state ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In some situations PAV alias devices on LPAR are not accessible.
The initialization procedure required to enable access to PAV alias
devices has to be performed per storage server subsystem and not
only once per storage server.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The dasd_page_cache should return page addresses and therefore the
cache must be created with an alignment of PAGE_SIZE.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The dasd function dasd_set_uid calls kzalloc while holding the
dasd_devmap_lock. Rearrange the code to do the memory allocation
outside the lock.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The request queue flush function of the dasd driver has to dequeue
the requests first and then call the end request function. Otherwise
a kernel bug in ll_rw_block.c might get triggered.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove system device class for xpram. It creates the directory hierarchy
under /sys/devices/system/xpram/xpram0. The xpram0 directory is empty and
it is always created while xpram1 and following devices are always missing,
independent if the devices exist or not. Since the xpram devices are
listed in /proc/partitions and /sys/block/ as slram<x> the system device
class for xpram is meaningless.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
I/O on a CCW device may stall if a channel path to that device is
logicaly varied off/on. A user I/O interrupt can get misinterpreted
as interrupt for an internal path verification operation due to a
missing check and is therefore never reported to the device driver.
Correct check for pending interruptions before starting path
verification.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Do a retry of read device characteristics / read configuration
data when a deferred condition code 1 is encountered in
ccw_device_wake_up().
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Without this patch register_tape_dev() will always fail, but might
return a value that is not an error number. This will lead to accesses
to already freed memory areas...
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Conflicts:
arch/ia64/hp/sim/simscsi.c
Stylistic differences in two separate fixes for buffer->request_buffer
problem.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Bug fixes for zfcp's erp:
- trigger adapter reopen if do_QDIO fails
- avoid erp deadlock if registration of scsi target or remote port hang
- do not treat as error if exchange port data fails
- decrease timeout for target reset and aborts
- mark unit failed if slave_destroy is called
Additionally some code cleanup was done:
- made some functions void when retval is not of interest
- shortened initialization of zfcp's host_template
- corrected some comments
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Improve request handling. Use hash table to manage request IDs.
Signed-off-by: Volker Sameske <sameske@de.ibm.com>
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fail to create a ccwgroup device if a ccw device is passed in twice.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In special conditions where a subchannel rejects the HALT I/O-
instruction with a busy indication (cc 2), I/O may stall.
I/O request termination logic retries HALT I/O indefinitely
because it expects HALT I/O to alter the subchannel status which
is not true when cc 2 is returned.
In case of a busy indication, try CLEAR I/O instruction immediately.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Take return values of sysfs_create_group & friends into account.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Display avg_sample_interval in nanoseconds, like it is documented.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Don't use memparse since the default size modifier is 'k'.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Ralph Wuerthner