__ieee80211_tasklet_handler -> __ieee80211_rx ->
__ieee80211_rx_handle_packet -> ieee80211_invoke_rx_handlers ->
ieee80211_rx_h_decrypt -> ieee80211_crypto_tkip_decrypt ->
ieee80211_tkip_decrypt_data -> iwl4965_mac_update_tkip_key ->
iwl_scan_cancel_timeout -> msleep
Ooops!
Avoid the sleep by changing iwl_scan_cancel_timeout with
iwl_scan_cancel and simply returning on failure if the scan persists.
This will cause hardware decryption to fail and we'll handle a few more
frames with software decryption.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In iwl_bg_request_scan function, if we could not send a
scan command it will go to done.
In done it does the right thing to call mac80211 with
scan complete, but the problem is STATUS_SCAN_HW is still
set causing any future scan to fail. Fix by clearing the scanning status
bits if scan fails.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unfortunately, the result was that mac80211 didn't see all the beacons
it actually wanted to see. This caused lost associations.
Hopefully we can revisit this when mac80211 is less greedy about seeing
beacons directly...
This reverts commit 063279062a.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When 'start' and 'end' are less than a cacheline apart and 'start' is
unaligned we are done after cleaning and invalidating the first
cacheline. So check for (start < end) which will not walk off into
invalid address ranges when (start > end).
This issue was caught by drivers/dma/dmatest.
2.6.27 is susceptible.
Cc: <stable@kernel.org>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Lothar WaÃ<9f>mann <LW@KARO-electronics.de>
Cc: Lennert Buytenhek <buytenh@marvell.com>
Cc: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
As a result of the ptebits changes, we ended up marking device mappings
as normal memory on ARMv7 CPUs, resulting in undesirable behaviour with
serial ports and the like. While reviewing the section mapping table
entries, other errors in the memory type settings for devices were
detected and confirmed to prevent Xscale3 platforms booting.
Tested on:
OMAP34xx (ARMv7),
OMAP24xx (ARMv6),
OMAP16xx (ARM926T, ARMv5),
PXA311 (Xscale3),
PXA272 (Xscale),
PXA255 (Xscale),
IXP42x (Xscale),
S3C2410 (ARM920T, ARMv4T),
ARM720T (ARMv4T)
StrongARM-110 (ARMv4)
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Mike Rapoport <mike@compulab.co.il>
Tested-by: Ben Dooks <ben-linux@fluff.org>
Tested-by: Anders Grafström <grfstrm@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes a regression introduced by 2c6e6db41f
"Minimize per_cpu reservations." That patch incorrectly used information about
what CPUs are possible that was not yet initialized by ACPI. The end result
was that per_cpu structures for offline CPUs were not initialized causing a
NULL pointer reference.
Since we cannot do the full acpi_boot_init() call any earlier, the simplest
fix is to just parse the MADT for SAPIC entries early to find the CPU
info. This should also allow for some cleanup of the code added by the
"Minimize per_cpu reservations". This patch just fixes the regressions, the
cleanup will come in a later patch.
Signed-off-by: Doug Chapman <doug.chapman@hp.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
CC: Robin Holt <holt@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
No functional change, just reorder some config options and update
the "Power management and ACPI" label to match the defacto x86
standard.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
As of 73bdf0a60e, the kernel needs
to know where modules are located in the virtual address space.
On ARM, we located this region between MODULE_START and MODULE_END.
Unfortunately, everyone else calls it MODULES_VADDR and MODULES_END.
Update ARM to use the same naming, so is_vmalloc_or_module_addr()
can work properly. Also update the comment on mm/vmalloc.c to
reflect that ARM also places modules in a separate region from the
vmalloc space.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit c7ffa6c262.
the assumptio of this change was that this would not break
any existing machine. Andrey Borzenkov reported troubles with
the ACPI reboot method: the system would hang on reboot, necessiating
a power cycle. Probably more systems are affected as well.
Also, there are patches queued up for v2.6.29 to disable virtualization
on emergency_restart() - which was the original motivation of
this change.
Reported-by: Andrey Borzenkov <arvidjaar@mail.ru>
Bisected-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: right-align /proc/meminfo consistent with other fields
When the split-LRU patches added Inactive(anon) and Inactive(file) lines
to /proc/meminfo, all counts were moved two columns rightwards to fit in.
Now move x86's DirectMap lines two columns rightwards to line up.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Lazy flushing needs to take care of the unmap path too which is not yet
implemented and leads to stale IO/TLB entries. This is fixed by this
patch.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The SAM9 watchdog driver is usable on the whole family of AT91SAM9 and
CAP9 processors.
Update the configuration to indicate this and allow the driver to be selected.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The architecture header files were recently moved from
include/asm-arm/mach-at91/ to arch/arm/mach-at91/include/mach/.
The SAM9 watchdog driver still includes a header from the old location.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Impact: fix rare x2apic hang
On x86, x2apic mode accesses for sending IPI's don't have serializing
semantics. If the IPI receivner refers(in lock-free fashion) to some
memory setup by the sender, the need for smp_mb() before sending the
IPI becomes critical in x2apic mode.
Add the smp_mb() in native_flush_tlb_others() before sending the IPI.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We currently oops with a divide error on starting a linear software
raid array consisting of at least two very small (< 500K) devices.
The bug is caused by the calculation of the hash table size which
tries to compute sector_div(sz, base) with "base" being zero due to
the small size of the component devices of the array.
Fix this by requiring the hash spacing to be at least one which
implies that also "base" is non-zero.
This bug has existed since about 2.6.14.
Cc: stable@kernel.org
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Impact: fix warning message when PARAVIRT is set in config
Remove stale #ifdef components from our IRQ sizing logic.
x86/Voyager is the only holdout.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch (as1159b) changes the timeout routines in the block core to
use round_jiffies_up(). There's no point in rounding the timer
deadline down, since if it expires too early we will have to restart
it.
The patch also removes some unnecessary tests when a request is
removed from the queue's timer list.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch (as1158b) adds round_jiffies_up() and friends. These
routines work like the analogous round_jiffies() functions, except
that they will never round down.
The new routines will be useful for timeouts where we don't care
exactly when the timer expires, provided it doesn't expire too soon.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Commit 0762b8bde9 moved disk_get_part()
in front of recursive get on the whole disk, which caused removable
devices to try disk_get_part() before rescanning after a new media is
inserted, which might fail legit open attempts or give the old
partition.
This patch fixes the problem by moving disk_get_part() after
__blkdev_get() on the whole disk.
This problem was spotted by Borislav Petkov.
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
smp_mb() is needed (to make the memory operations visible globally) before
sending the ipi on the sender and the receiver (on Alpha atleast) needs
smp_read_barrier_depends() in the handler before reading the call_single_queue
list in a lock-free fashion.
On x86, x2apic mode register accesses for sending IPI's don't have serializing
semantics. So the need for smp_mb() before sending the IPI becomes more
critical in x2apic mode.
Remove the unnecessary smp_mb() in csd_flag_wait(), as the presence of that
smp_mb() doesn't mean anything on the sender, when the ipi receiver is not
doing any thing special (like memory fence) after clearing the CSD_FLAG_WAIT.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Move the calling blk_delete_timer to later in end_that_request_last to
address an issue where blkdev_dequeue_request may have add a timer for the
request.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Block queue supports two usage models - one where block driver peeks
at the front of queue using elv_next_request(), processes it and
finishes it and the other where block driver peeks at the front of
queue, dequeue the request using blkdev_dequeue_request() and finishes
it. The latter is more flexible as it allows the driver to process
multiple commands concurrently.
These two inconsistent usage models affect the block layer
implementation confusing. For some, elv_next_request() is considered
the issue point while others consider blkdev_dequeue_request() the
issue point.
Till now the inconsistency mostly affect only accounting, so it didn't
really break anything seriously; however, with block layer timeout,
this inconsistency hits hard. Block layer considers
elv_next_request() the issue point and adds timer but SCSI layer
thinks it was just peeking and when the request can't process the
command right away, it's just left there without further processing.
This makes the request dangling on the timer list and, when the timer
goes off, the request which the SCSI layer and below think is still on
the block queue ends up in the EH queue, causing various problems - EH
hang (failed count goes over busy count and EH never wakes up),
WARN_ON() and oopses as low level driver trying to handle the unknown
command, etc. depending on the timing.
As SCSI midlayer is the only user of block layer timer at the moment,
moving blk_add_timer() to elv_dequeue_request() fixes the problem;
however, this two usage models definitely need to be cleaned up in the
future.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Define __BIOVEC_PHYS_MERGEABLE as the default implementation of
BIOVEC_PHYS_MERGEABLE, so that its available for reuse within an
arch-specific definition of BIOVEC_PHYS_MERGEABLE.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Impact: clarify menuconfig text
Mention ACPI in the top-level menu to give a clue as to where
it lives. This matches what ia64 does.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Adding a spare to a raid10 doesn't cause recovery to start.
This is due to an silly type in
commit 6c2fce2ef6
and so is a bug in 2.6.27 and .28-rc.
Thanks to Thomas Backlund for bisecting to find this.
Cc: Thomas Backlund <tmb@mandriva.org>
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
It turns out that it is only safe to call blkdev_ioctl when the device
is actually open (as ->bd_disk is set to NULL on last close). And it
is quite possible for do_md_stop to be called when the device is not
open. So discard the call to blkdev_ioctl(BLKRRPART) which was
added in
commit 934d9c23b4
It is just as easy to call this ioctl from userspace when needed (on
mdadm -S) so leave it out of the kernel
Signed-off-by: NeilBrown <neilb@suse.de>
Impact: make NR_IRQS big enough for system with lots of apic/pins
If lots of IO_APIC's are there (or can be there), size the same way
as 64-bit, depending on MAX_IO_APICS and NR_CPUS.
This fixes the boot problem reported by Ben Hutchings on a 32-bit
server with 5 IO-APICs and 240 IO-APIC pins.
Signed-off-by: Yinghai <yinghai@kernel.org>
Tested-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix boot hang on 32-bit systems with more than 224 IO-APIC pins
On some 32-bit systems with a lot of IO-APICs probe_nr_irqs() can
return a value larger than NR_IRQS. This will lead to probe_irq_on()
overrunning the irq_desc array.
I hit this when running net-next-2.6 (close to 2.6.28-rc3) on a
Supermicro dual Xeon system. NR_IRQS is 224 but probe_nr_irqs() detects
5 IOAPICs and returns 240. Here are the log messages:
Tue Nov 4 16:53:47 2008 ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
Tue Nov 4 16:53:47 2008 IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
Tue Nov 4 16:53:47 2008 ACPI: IOAPIC (id[0x02] address[0xfec81000] gsi_base[24])
Tue Nov 4 16:53:47 2008 IOAPIC[1]: apic_id 2, version 32, address 0xfec81000, GSI 24-47
Tue Nov 4 16:53:47 2008 ACPI: IOAPIC (id[0x03] address[0xfec81400] gsi_base[48])
Tue Nov 4 16:53:47 2008 IOAPIC[2]: apic_id 3, version 32, address 0xfec81400, GSI 48-71
Tue Nov 4 16:53:47 2008 ACPI: IOAPIC (id[0x04] address[0xfec82000] gsi_base[72])
Tue Nov 4 16:53:47 2008 IOAPIC[3]: apic_id 4, version 32, address 0xfec82000, GSI 72-95
Tue Nov 4 16:53:47 2008 ACPI: IOAPIC (id[0x05] address[0xfec82400] gsi_base[96])
Tue Nov 4 16:53:47 2008 IOAPIC[4]: apic_id 5, version 32, address 0xfec82400, GSI 96-119
Tue Nov 4 16:53:47 2008 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
Tue Nov 4 16:53:47 2008 ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Tue Nov 4 16:53:47 2008 Enabling APIC mode: Flat. Using 5 I/O APICs
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
deflate_mutex protects the globals lzo_mem and lzo_compress_buf. However,
jffs2_lzo_compress() unlocks deflate_mutex _before_ it has copied out the
compressed data from lzo_compress_buf. Correct this by moving the mutex
unlock after the copy.
In addition, document what deflate_mutex actually protects.
Cc: stable@kernel.org
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Richard Purdie <rpurdie@openedhand.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix printk format warnings in net/9p.
Built cleanly on 7 arches.
net/9p/client.c:820: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
net/9p/client.c:820: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:867: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
net/9p/client.c:867: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:932: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:932: warning: format '%llx' expects type 'long long unsigned int', but argument 6 has type 'u64'
net/9p/client.c:982: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
net/9p/client.c:982: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:1025: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
net/9p/client.c:1025: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:1227: warning: format '%llx' expects type 'long long unsigned int', but argument 7 has type 'u64'
net/9p/client.c:1227: warning: format '%llx' expects type 'long long unsigned int', but argument 12 has type 'u64'
net/9p/client.c:1227: warning: format '%llx' expects type 'long long unsigned int', but argument 8 has type 'u64'
net/9p/client.c:1227: warning: format '%llx' expects type 'long long unsigned int', but argument 13 has type 'u64'
net/9p/client.c:1252: warning: format '%llx' expects type 'long long unsigned int', but argument 7 has type 'u64'
net/9p/client.c:1252: warning: format '%llx' expects type 'long long unsigned int', but argument 12 has type 'u64'
net/9p/client.c:1252: warning: format '%llx' expects type 'long long unsigned int', but argument 8 has type 'u64'
net/9p/client.c:1252: warning: format '%llx' expects type 'long long unsigned int', but argument 13 has type 'u64'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Removed duplicated #include <rdma/ib_verbs.h> in
net/9p/trans_rdma.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
If a T or R fcall cannot be allocated, the function returns an error
but neglects to free the wait queue that was successfully allocated.
If it comes through again a second time this wq will be overwritten
with a new allocation and the old allocation will be leaked.
Also, if the client is subsequently closed, the close path will
attempt to clean up these allocations, so set the req fields to
NULL to avoid duplicate free.
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
T and R fcall are reused until the client is destroyed. There does
not need to be a special case for Flush
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
The client lock must be IRQ safe. Some of the lock acquisition paths
took regular spin locks.
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
The RDMA connection manager is fundamentally asynchronous.
Since the async callback context is the client pointer, the
transport in the client struct needs to be set prior to calling
the first async op.
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Impact: improve wakeup affinity on NUMA systems, tweak SMP systems
Given the fixes+tweaks to the wakeup-buddy code, re-tweak the domain
balancing defaults on NUMA and SMP systems.
Turn on SD_WAKE_AFFINE which was off on x86 NUMA - there's no reason
why we would not want to have wakeup affinity across nodes as well.
(we already do this in the standard NUMA template.)
lat_ctx on a NUMA box is particularly happy about this change:
before:
| phoenix:~/l> ./lat_ctx -s 0 2
| "size=0k ovr=2.60
| 2 5.70
after:
| phoenix:~/l> ./lat_ctx -s 0 2
| "size=0k ovr=2.65
| 2 2.07
a 2.75x speedup.
pipe-test is similarly happy about it too:
| phoenix:~/sched-tests> ./pipe-test
| 18.26 usecs/loop.
| 14.70 usecs/loop.
| 14.38 usecs/loop.
| 10.55 usecs/loop. # +WAKE_AFFINE on domain0+domain1
| 8.63 usecs/loop.
| 8.59 usecs/loop.
| 9.03 usecs/loop.
| 8.94 usecs/loop.
| 8.96 usecs/loop.
| 8.63 usecs/loop.
Also:
- disable SD_BALANCE_NEWIDLE on NUMA and SMP domains (keep it for siblings)
- enable SD_WAKE_BALANCE on SMP domains
Sysbench+postgresql improves all around the board, quite significantly:
.28-rc3-11474e2c .28-rc3-11474e2c-tune
-------------------------------------------------
1: 571 688 +17.08%
2: 1236 1206 -2.55%
4: 2381 2642 +9.89%
8: 4958 5164 +3.99%
16: 9580 9574 -0.07%
32: 7128 8118 +12.20%
64: 7342 8266 +11.18%
128: 7342 8064 +8.95%
256: 7519 7884 +4.62%
512: 7350 7731 +4.93%
-------------------------------------------------
SUM: 55412 59341 +6.62%
So it's a win both for the runup portion, the peak area and the tail.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
For "unlock" cycles to 16bit devices in 8bit compatibility mode we need
to use the byte addresses 0xaaa and 0x555. These effectively match
the word address 0x555 and 0x2aa, except the latter has its low bit set.
Most chips don't care about the value of the 'A-1' pin in x8 mode,
but some -- like the ST M29W320D -- do. So we need to be careful to
set it where appropriate.
cfi_send_gen_cmd is only ever passed addresses where the low byte
is 0x00, 0x55 or 0xaa. Of those, only addresses ending 0xaa are
affected by this patch, by masking in the extra low bit when the device
is known to be in compatibility mode.
[dwmw2: Do it only when (cmd_ofs & 0xff) == 0xaa]
v4: Fix stupid typo in cfi_build_cmd_addr that failed to compile
I'm writing this patch way to late at night.
v3: Bring all of the work back into cfi_build_cmd_addr
including calling of map_bankwidth(map) and cfi_interleave(cfi)
So every caller doesn't need to.
v2: Only modified the address if we our device_type is larger than our
bus width.
Cc: stable@kernel.org
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Vito Caputo noticed that tcp_recvmsg() returns immediately from
partial reads when MSG_PEEK is used. In particular, this means that
SO_RCVLOWAT is not respected.
Simply remove the test. And this matches the behavior of several
other systems, including BSD.
Signed-off-by: David S. Miller <davem@davemloft.net>
With some net devices types, an IPv6 address configured while the
interface was down can stay 'tentative' forever, even after the interface
is set up. In some case, pending IPv6 DADs are not executed when the
device becomes ready.
I observed this while doing some tests with kvm. If I assign an IPv6
address to my interface eth0 (kvm driver rtl8139) when it is still down
then the address is flagged tentative (IFA_F_TENTATIVE). Then, I set
eth0 up, and to my surprise, the address stays 'tentative', no DAD is
executed and the address can't be pinged.
I also observed the same behaviour, without kvm, with virtual interfaces
types macvlan and veth.
Some easy steps to reproduce the issue with macvlan:
1. ip link add link eth0 type macvlan
2. ip -6 addr add 2003::ab32/64 dev macvlan0
3. ip addr show dev macvlan0
...
inet6 2003::ab32/64 scope global tentative
...
4. ip link set macvlan0 up
5. ip addr show dev macvlan0
...
inet6 2003::ab32/64 scope global tentative
...
Address is still tentative
I think there's a bug in net/ipv6/addrconf.c, addrconf_notify():
addrconf_dad_run() is not always run when the interface is flagged IF_READY.
Currently it is only run when receiving NETDEV_CHANGE event. Looks like
some (virtual) devices doesn't send this event when becoming up.
For both NETDEV_UP and NETDEV_CHANGE events, when the interface becomes
ready, run_pending should be set to 1. Patch below.
'run_pending = 1' could be moved below the if/else block but it makes
the code less readable.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix printk format warnings in net/9p.
Built cleanly on 7 arches.
net/9p/client.c:820: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
net/9p/client.c:820: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:867: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
net/9p/client.c:867: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:932: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:932: warning: format '%llx' expects type 'long long unsigned int', but argument 6 has type 'u64'
net/9p/client.c:982: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
net/9p/client.c:982: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:1025: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
net/9p/client.c:1025: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:1227: warning: format '%llx' expects type 'long long unsigned int', but argument 7 has type 'u64'
net/9p/client.c:1227: warning: format '%llx' expects type 'long long unsigned int', but argument 12 has type 'u64'
net/9p/client.c:1227: warning: format '%llx' expects type 'long long unsigned int', but argument 8 has type 'u64'
net/9p/client.c:1227: warning: format '%llx' expects type 'long long unsigned int', but argument 13 has type 'u64'
net/9p/client.c:1252: warning: format '%llx' expects type 'long long unsigned int', but argument 7 has type 'u64'
net/9p/client.c:1252: warning: format '%llx' expects type 'long long unsigned int', but argument 12 has type 'u64'
net/9p/client.c:1252: warning: format '%llx' expects type 'long long unsigned int', but argument 8 has type 'u64'
net/9p/client.c:1252: warning: format '%llx' expects type 'long long unsigned int', but argument 13 has type 'u64'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: scheduling order fix for group scheduling
For each level in the hierarchy, set the buddy to point to the right entity.
Therefore, when we do the hierarchical schedule, we have a fair chance of
ending up where we meant to.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: improve/change/fix wakeup-buddy scheduling
Currently we only have a forward looking buddy, that is, we prefer to
schedule to the task we last woke up, under the presumption that its
going to consume the data we just produced, and therefore will have
cache hot benefits.
This allows co-waking producer/consumer task pairs to run ahead of the
pack for a little while, keeping their cache warm. Without this, we
would interleave all pairs, utterly trashing the cache.
This patch introduces a backward looking buddy, that is, suppose that
in the above scenario, the consumer preempts the producer before it
can go to sleep, we will therefore miss the wakeup from consumer to
producer (its already running, after all), breaking the cycle and
reverting to the cache-trashing interleaved schedule pattern.
The backward buddy will try to schedule back to the task that woke us
up in case the forward buddy is not available, under the assumption
that the last task will be the one with the most cache hot task around
barring current.
This will basically allow a task to continue after it got preempted.
In order to avoid starvation, we allow either buddy to get wakeup_gran
ahead of the pack.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix cross-class preemption
Inter-class wakeup preemptions should go on class order.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
John W. Linville