The changes in the mmu version of entry.h (entry_mm.h) and the non-mmu
version (entry_no.h) are not about the presence or use of an MMU at all.
The main changes are to support the ColdFire processors. The code for
trap entry and exit for all types of 68k processor outside coldfire is
the same.
So merge the files back to a single entry.h and share the common 68k
entry/exit code. Some changes are required for the non-mmu entry
handlers to adopt the differing macros for system call and interrupt
entry, but this is quite strait forward. The changes for the ColdFire
remove a couple of instructions for the separate a7 register case, and
are no worse for the older single a7 register case.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Most of the build logic is the same for the mmu and non-mmu m68k targets.
Merge the top level architecture Makefiles back into a single Makefile.
For the most part this is just adding the non-mmu processor types and
their specific cflags and other options into the mmu Makefile.
Note that all the BOARD setting logic that was in the non-mmu Makefile
is completely removed. It was no longer being used at all.
This has been build and run tested on ColdFire targets and ARAnyM.
It has been build tested on all the m68k defconfig targets using a
gcc-4.5.1 based toolchain.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
The problem has its root in the calculation of the set-port offsets (macro
MCFGPIO_SETR() in arch/m68k/include/asm/gpio.h), this assumes that all ports
have the same offset from the base port address (MCFGPIO_SETR) which is
defined in mcf520xsim.h as an alias of MCFGIO_PSETR_BUSCTL. Because the BUSCTL
and BE port do not have a set-register (see MCF5208 Reference Manual Page
13-10, Table 13-3) the offset calculations went wrong.
Because the BE and BUSCTL port do not seem useful in these parts, as they
lack a set register, I removed them and adapted the gpio chip bases which
are also used for the offset-calculations. Now both setting and resetting
the chip selects works as expected from userland and from the kernelspace.
Signed-off-by: Peter Turczak <peter@turczak.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
commit 2502b667ea ("Change the m68knommu irq
handling to use the generic irq framework.") removed the reporting of spurious
interrupts on nommu (68328 and 68360).
Bring it back in a generic way, using "atomic_t irq_err_count", as that's what
most of the other architectures are using.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Currently trap_init() is an empty function for m68knommu. Instead
the vectors are being setup as part of the IRQ initialization.
This is inconsistent with m68k and other architectures.
Change the local init_vectors() to be trap_init(), and init the
vectors at the correct time during startup. This will help merge of
m68k and m68knommu trap code in the furture.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire 5206 and 5206e CPU families are almost identical, we can
easily merge the platform support code for them. All the differences
are dealt with in the current include/asm/5206sim.h.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The non-MMU m68k targets can use the same asm/system.h as the MMU
targets. So switch the current system_mm.h to be system.h and remove
system_no.h.
The assembly support code for the non-MMU resume functions needs to
be modified to match the now common switch_to() macro. Specifically
this means correctly saving and restoring the status flags in the case
of the ColdFire resume, and some reordering of the code to not use
registers before they are saved or after they are restored.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
It is strait forward to merge the mmu and non-mmu versions of
asm-offstes.c. Some name changes are required for the preempt and
thread_info.flags in the non-mmu entry.S assembler to make them
consistent for both setups.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
There is no reason most of the symbols enclosed in a conditional
on CONFIG_COLDFIRE need to be exported. And they sure don't need to
be doing it in m68k_ksyms_no.c. Move the dma symbols export (which
are currently needed) to the definitions of those, and remove the
rest of the exporting here.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
There is a lot of common code that could be shared between the m68k
and m68knommu arch branches. It makes sense to merge the two branches
into a single directory structure so that we can more easily share
that common code.
This is a brute force merge, based on a script from Stephen King
<sfking@fdwdc.com>, which was originally written by Arnd Bergmann
<arnd@arndb.de>.
> The script was inspired by the script Sam Ravnborg used to merge the
> includes from m68knommu. For those files common to both arches but
> differing in content, the m68k version of the file is renamed to
> <file>_mm.<ext> and the m68knommu version of the file is moved into the
> corresponding m68k directory and renamed <file>_no.<ext> and a small
> wrapper file <file>.<ext> is used to select between the two version. Files
> that are common to both but don't differ are removed from the m68knommu
> tree and files and directories that are unique to the m68knommu tree are
> moved to the m68k tree. Finally, the arch/m68knommu tree is removed.
>
> To select between the the versions of the files, the wrapper uses
>
> #ifdef CONFIG_MMU
> #include <file>_mm.<ext>
> #else
> #include <file>_no.<ext>
> #endif
On top of this file merge I have done a simplistic merge of m68k and
m68knommu Kconfig, which primarily attempts to keep existing options and
menus in place. Other than a handful of options being moved it produces
identical .config outputs on m68k and m68knommu targets I tested it on.
With this in place there is now quite a bit of scope for merge cleanups
in future patches.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Greg Ungerer