Make the eeprom routines less dependent on the iwl_priv structure.
Don't use the priv when bus structure is sufficient.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi tries to avoid using antenna B in BT combo devices when BT
is active. A bug in the rate-scaling algorithm was causing the combo
device to never attempt MIMO rates. Fix the algorithm to
opportunistically try MIMO rates when BT traffic is low.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Users complain that the traffic gets stalled sometimes. This will
allow easier debugging.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This bit was used only once. Use IWL_DL_INFO instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to the P2P context always having the associated
bit set when we got to this code, we were splitting
up the remain-on-channel durations unconditionally.
This isn't needed -- if the P2P context is in P2P
device type mode it doesn't impose restrictions on
timing to skip it in that case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The device expects TU but we get ms, so convert.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Warning introduced by c847474b7dfdda304d0d8ffcc5a9db546b1cb3e9
iwlwifi: check status before send command
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check the status before sending host command, if any of the condition
match, cancel the host command before queue
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"echo" host command has no data, set the length to 0
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The core suspend function is part of agn, iwl_mac80211 should only
handle mac80211 I/F operations.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The station related mac80211 callback functions should belong to _mac80211
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlagn_mac_hw_scan should belong to _mac80211 callback.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move more mac80211 related functions to _mac80211 file
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In P2P device mode, the device needs to have valid
QoS parameters. We currently have those because we
program parameters from any virtual interface into
all contexts, but not only do we want to get rid of
this -- it is also unpredictable since on the BSS
context we might have any parameters, and there it
might even be programmed for HT.
Explicitly program default QoS parameters into the
PAN context for P2P (the defaults are 11g but with
QoS disabled) to make device behaviour predictable.
This also helps when in a follow-up patch we will
use TX QoS parameters from mac80211 only for the
context they were meant for -- without this first
that would completely break P2P device discovery.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad added the ability to configure AC parameters
per virtual interface; make use of this in iwlwifi
and set the parameters in the right context. Since
storage and uploading to the device is already per
context, this is sufficient.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are many mac80211 callback functions in the driver, as current
implementation, those functions are scatter everywhere which is very difficult
to find and maintain, move all the mac80211 callback functions into single
file. There should be no functional changes
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Relocate the ucode files and update relevant code.
More code refactoring.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the knowledge of the ucode image to lower level routines. Also do
not pass the iwl_priv structure lower than it needs to be.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The upper layers of the driver do not need to know where the ucode is
stored. It already passes in an enum of which ucode to load. Let the
lower layer routines select the ucode to load.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ucode_write_complete is used for ucode loading. Move it as part of
restructuring work out of the priv structure.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BG only SKUs are no longer supported by 2000 and 1x5 series. Remove it
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reinette reports a crash in iwl_reprogram_ap_sta(). The
debugging shows:
b1 16 mov $0x16,%cl
*f3 a5 rep movsl %ds <-- trapping instruction:(%rsi),%es:(%rdi)
which is a memcpy of 22 (0x16) words (movsl). this points
to "priv->stations[sta_id].lq" being NULL since that is
the memcpy() of that size here.
The only way I see for this to happen is if we try to
do some RXON reprogramming while connecting to an AP,
after tx_sync() but before full setup, but that seems
like something that might very well happen.
Fix this by checking if the LQ is present and only then
reprogramming it.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check and report WARN only when its invalid
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add two more SKUs for 6x05 series of device.
First SKU has low 5GHz channels actives, the other SKU has high 5GHz channels actives.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a station is associated with an AP and the RF_KILL switch is engaged,
numerous error messages were sent to the system log. The error messages
were the result of the failure(s) of the various submodules to perform
their tasks after the radios were disabled.
To resolve this situation, the messages were modified to use a new macro,
IWL_DEBUG_QUIET_RFKILL. This macro allows for the RF_KILL error messages
to be sent to the log provided that IWL_DEBUG is true and IWL_DL_RADIO
is '1'. For all other cases, the error messages resulting from an RFKILL
event will not be sent to the system log. Messages logged because of an
RFKILL will be tagged with the prefix '(RFKILL)' to clarify the cause of
the error.
Signed-off-by: Todd Previte <toddX.a.previte@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whether to use NoA or not is entire controlled
by the uCode right now, and it also adds the
attribute to beacons. We do need to add it to
probe responses in the driver though.
Keep track of the NoA notification from the
uCode and add the data to probe responses when
such are transmitted. Use RCU to manage the
lifetime.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Retriving tx power for 2x2 and 3x3 chainmask is not handled
properly. While calculating tx power for 2x2, 3 dBm was reduced
and for 3x3, 5 dBm was reduced which should be added back when
retriving.
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow setting a probe response template for an interface operating in
AP mode. Low level drivers are notified about changes in the probe
response template and are able to retrieve a copy of the current probe
response. This data can, for example, be uploaded to hardware as a
template.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pass probe-response data from usermode via beacon parameters.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Notify user-space about probe-response offloading support in the driver.
A wiphy flag is used to indicate support and a bitmap of protocols
determines which protocols are supported.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John reported the following warning:
net/wireless/nl80211.c: In function ‘nl80211_tx_mgmt’:
net/wireless/nl80211.c:5286:8: warning: ‘hdr’ may be used uninitialized in this function
Evidently, his version of gcc isn't able to see that
when "msg" is initialized, "hdr" must also be. My
gcc, 4.6.1, can actually see that and doesn't warn.
Simply initialize the variable to NULL. That means
if the compiler was ever right we'll crash though so
isn't really optimal since it may hide warnings from
the compiler when somebody modifies this code in the
future.
Reported-by: John Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most ath9k devices are PCI/PCIe based, therefor making PCI/PCIe support
default y helps those porting a config from 2.6 kernel series
from getting "non-functional" wireless drivers with 3.x kernel series.
Signed-off-by: Daniel Kuehn <daniel@kuehn.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The macro is only used in ipw2200 and we certainly
don't want to encourage its use, so move it out of
the radiotap header file and into the driver.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver should be instructed to enter PS AFTER
reconfiguring ASSOCIATED (in STA case) using ieee80211_bss_info_change_notify
same as it's being done in ieee80211_set_associated()
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check if NCI data flow control is used in nci_tx_work.
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unused NCI operations, e.g. create static rf connection.
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Addition, deletion and modification of NCI constants.
Changes in NCI commands, responses and notifications structures.
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just add API to get the channel & report it. Trivial really.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Attempting to micro-optimise the scan by going
fully live again when scanning the operating
channel just made the code extremely complex
and has little gain in most use cases. Remove
all that code and simplify the state machine
again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 should set carrier_on for ibss vifs
only while they are joined (similar to sta vifs)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch sync up CalFreqPeir channel list and paprd rate mask
of AR938x templates to the latest received from Systems team.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure xpa timing field while loading boad defaults to
fix 11b CCK spur issue that was observed in EMI testing.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Read and configure quick drop feild from AR9003 eeprom
inorder to help with strong signal. This patch also removes
obsolate parameters ob, db_stage2, db_stage_3, db_stage4
from the eeprom templates.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Following compilation warning is fixed by releasing referenced BSS
structure returned by cfg80211_inform_bss().
"warning: ignoring return value of cfg80211_inform_bss,
declared with attribute warn_unused_result"
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cfg80211 stack allocates private area for driver use in
struct cfg80211_bss. It will be freed by stack in bss_release().
Driver don't need to worry about it.
In mwifiex driver, we use the private area just to store band
information(u8). We don't allocate memory explicitly and store
it's pointer in bss->priv. Hence we don't have any cleanup work
to do in free_priv handler. Currently we try to free the allocated
private area in free_priv handler which is not correct.
This patch removes unnecessary free_priv handler.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Following three warnings are fixed:
>init.c +256 mwifiex_init_adapter(71)
>warn: variable dereferenced before check 'adapter->sleep_cfm'
>(see line 191)
>sta_rx.c +193 mwifiex_process_sta_rx_packet(75)
>warn: variable dereferenced before check 'priv' (see line 182)
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename DataRate to data_rate and arrange 'for' loop
for better readability.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Functions mwifiex_11n_dispatch_pkt_until_start_win and
mwifiex_11n_scan_and_dispatch used to always return value
zero for all inputs. Changing these functions to void.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don Fry