Add the function to register the MUSB platform device.
Additional compile warning fixes by Sekhar Nori.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Rename setup_usb() into davinci_setup_usb(). While at it:
- move its declaration from <mach/common.h> to more fitting <mach/usb.h>;
- teach it to handle values of the 'mA' parameter greater than 510 and thus
pass 1000 instead of 500 for the power switches capable of sourcing over 1 A;
- teach it to handle odd values of the 'potpgt_ms' parameter...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
There have accumulated quite a lot of them after the code reorganizations...
In several cases I had to replace #include <linux/dma-mapping.h> which wasn't
needed directly but happened to #include <linux/err.h> which was needed.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add the function to register the OHCI platform device, given the root hub
related platform data passed from the board specific code. The platfrom
data provide for overriding the OHCI port power and over-current bits at
the board level.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DM646x has MUSB connected to IRQs 13 and 14 (unlike IRQ12 on other platforms),
so pass the correct IRQ resources with the platform device.
Signed-off-by: Dmitry Krivoschekov <dkrivoschekov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add arch-specific ioremap() which uses any existing static mappings in
place of doing a new mapping. From now on, drivers should always use
ioremap() instead of IO_ADDRESS().
In addition, remove the davinci_[read|write]* macros in favor of using
ioremap.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that the musb build fixes for DaVinci got merged (RC3?), kick in
the other bits needed to get it finally *working* in mainline:
- Use clk_enable()/clk_disable() ... the "always enable USB clocks"
code this originally relied on has since been removed.
- Initialize the USB device only after the relevant I2C GPIOs are
available, so the host side can properly enable VBUS.
- Tweak init sequencing to cope with mainline's relatively late init
of the I2C system bus for power switches, transceivers, and so on.
Sanity tested on DM6664 EVM for host and peripheral modes; that system
won't boot with CONFIG_PM enabled, so OTG can't yet be tested. Also
verified on OMAP3.
(Unrelated: correct the MODULE_PARM_DESC spelling of musb_debug.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The DaVinci code had an implementation of the OTG transceiver glue
too; make it use the new-standard one.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
From: David Brownell <dbrownell@users.sourceforge.net>
Subject: ARM/mach-davinci/usb.c buildfix
CC arch/arm/mach-davinci/usb.o
arch/arm/mach-davinci/usb.c:60: error: 'IRQ_USBINT' undeclared here (not in a function)
make[1]: *** [arch/arm/mach-davinci/usb.o] Error 1
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Declare the musb_hdrc platform device for DaVinci.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Sergei Shtylyov