Added a new option "snoop" for the traffic control of the HD-audio
controller chip. When set to 0, the non-snooping mode is used with
the traffic control bit is set in each stream control register.
This may allow better operations in the low power mode, but the actual
implementation is depending pretty much on the chipset.
As already implemented, more or less each chipset has own snoop-control
register bit. Now this setup refers to the snoop option, too.
Also, a new VIA chipset may require the non-snooping mode when set so
in BIOS. In such a case, the option value is overridden.
As default, it's still set to snoop=1 for keeping the same behavior as
before. In near future, it'll be set to 0 as default after checking
it works in every system well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add new parameter to disable rounding of buffer/period sizes to
multiples of 128 bytes. This is more efficient in terms of memory
access but isn't required by the HDA spec and prevents users from
specifying exact period/buffer sizes. For example for 44.1kHz, a
period size set to 20ms will be rounded to 19.59ms.
Tested and enabled on Intel HDA controllers. Option is disabled by
default for other controllers.
Tested-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added a new driver for supporting Digigram Lola PCI-e boards.
Lola has a similar h/w design like HD-audio but with extended verbs.
Thus the driver is written similarly like HD-audio driver in the bus
part. The codec part is rather written in a fixed way specific to the
Lola board because of the verb incompatibility.
The driver provides basic PCM, supporting multi-streams and mixing.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix some minor typos:
* informations => information
* there own => their own
* these => this
Signed-off-by: Sylvestre Ledru <sylvestre.ledru@scilab.org>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add experimental support for the Asus Xonar HDAV1.3 Slim sound card.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add experimental support for the Asus Xonar DG sound card.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for the AuzenTech X-Meridian 7.1 2G sound card.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for the TempoTec/MediaTek HiFier Serenade sound card.
The PCI ID was already there, but the driver handled it like the
Fantasia model, which resulted in a dummy recording device. As
a stereo output-only card, this model is to be handled exactly
like the HG2PCI.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for the Kuroutoshikou CMI8787-HG2PCI sound card.
[replaced non-latin letters in the patch by tiwai]
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The snd-hifier driver contains more duplicated code than model-specific
code, so it does not make sense for it to be a separate driver.
Handling the two-channel output restriction can be easily done in the
generic driver.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Its hardware is handled more fully by the new azt1605/azt2316 drivers.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a new driver for Aztech Sound Galaxy ISA soundcards based on the
AZT1605 and AZT2316 chipsets. It's constructed as two seperate drivers
for either chipset generated from the same source file, with (very)
minimal ifdeffery.
The drivers check the SB DSP version to decide if they are being loaded
for the right chip. AZT1605 returns 2.1 by default and AZT2316 3.1.
This isn't full-proof as the DSP version can actually be set through
software but it's close enough -- as far as I've been able to see, the
DSP version can not be stored in the EEPROM and the cards will therefore
startup with the defaults.
This distinction could (with the same success rate) also be used to
decide which chip we're looking at at runtime meaning a single, merged
driver is also an option but I feel it's actually nicer this way. A
merged driver would have to postpone translating the passed in resource
values to the card configuration until it knew which one it was looking
at and would need to postpone erring out on mpu_irq=10 for azt1605 and
mpu_irq=3 for azt2316.
The drivers have been tested on various cards. For snd-azt1605:
FCC-ID I38-MMSN811: Aztech Sound Galaxy Nova 16 Extra
FCC-ID I38-MMSN822: Aztech Sound Galaxy Pro 16 II
and for snd-azt2316:
FCC-ID I38-MMSN824: Aztech Sound Galaxy Pro 16 AB
FCC-ID I38-MMSN826: Trust Sound Expert DeLuxe Wave 32 (05201)
FCC-ID I38-MMSN830: Trust Sound Expert DeLuxe 16+ (05202)
FCC-ID I38-MMSN837: Packard Bell ISA Soundcard 030069
FCC-ID I38-MMSN846: Trust Sound Expert DeLuxe 16-3D (06300)
FCC-ID I38-MMSN847: Trust Sound Expert DeLuxe Wave 32-3D (06301)
FCC-ID I38-MMSN852: Aztech Sound Galaxy Waverider Pro 32-3D
826 and 846 were also marketed directly by Aztech and then known as:
FCC-ID I38-MMSN826: Aztech Sound Galaxy Waverider 32+
FCC-ID I38-MMSN846: Aztech Sound Galaxy Nova 16 Extra II-3D
Together, these cover the AZT1605 and AT2316A, AZT2316R and AZT2316-S
chipsets. All cards work fully -- full-duplex PCM, MIDI and FM. Full
duplex is a little flaky on some.
I38-MSN811 tends to not work in full-duplex but sometimes does with the
highest success rate being achieved when you first start the capture and
then a playback instead of the other way around (it's a CS4231-KL
codec).
The cards with an AD1845XP codec (my I38-MMSN826 and one of my
I38-MMSN830s) are also somewhat duplex-challenged. Sometimes full-duplex
works, sometimes not and this varies from try to try. This seems likely
to be a timing problem somewhere inside wss-lib.
I38-MMSN826 has an additional "ICS2115 WaveFront" wavetable synth
onboard that isn't supported yet. The wavetable synths on I38-MMSN847
and I38-MMSN852 are wired directly to the standard MPU-401 UART and the
AUX1 input on the codec and work without problem.
CD-ROM audio on the cards is routed to the codec "Line" input, Line-In
to its Aux input, and FM/Wavetable to its AUX1 input. I did not rename
the controls due to the capture source enumeration: I see that
capture-source overrides are hardcoded in wss-lib and this is just too
ugly to live.
Versus the old snd-sgalaxy driver these drivers add support for the
models without a configuration EEPROM (which are common), full-duplex,
MPU-401 UART and OPL3. In the future they might grow support for that
ICS2115 WaveFront synth on 826 and an hwdep interface to write to the
EEPROM on the models that have one.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Below you will find an updated version from the original series bunching all patches into one big patch
updating broken web addresses that are located in Documentation/*
Some of the addresses date as far far back as 1995 etc... so searching became a bit difficult,
the best way to deal with these is to use web.archive.org to locate these addresses that are outdated.
Now there are also some addresses pointing to .spec files some are located, but some(after searching
on the companies site)where still no where to be found. In this case I just changed the address
to the company site this way the users can contact the company and they can locate them for the users.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Cc: Paulo Marques <pmarques@grupopie.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Michael Neuling <mikey@neuling.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The ESS ES968 chip is nothing more then a PnP companion
for a non-PnP audio chip. It was paired with non-PnP ESS' chips:
ES688 and ES1688. The ESS' audio chips are handled by the es1688
driver in native mode. The PnP cards are handled by the ES968
driver in SB compatible mode.
Move the ES968 chip handling to the es1688 driver so the driver
can handle both PnP and non-PnP cards. The es968 is removed.
Also, a new PnP id is added for the card I acquired (the change
was tested on this card).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the support of AudioScience ASI boards.
The driver has been tested for years on alsa-driver external tree,
now finally got merged to the kernel.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for the Edirol UA-1000 to the UA-101 driver.
Both devices behave the same, so we just have to shuffle around some
interface numbers and name strings.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Narrow the dma and irq selection after the DOS driver.
Add ALSA configuration description as well.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add experimental support for the Edirol UA-101 audio/MIDI interface.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, if the high-res timers are unavailable, snd-pcsp does not
initialize. People who choose it over pcspkr, loose their console beeps
in that case and get annoyed.
With this patch, the console beeps remain regardless of the high-res
timers. Additionally, the "nopcm" modparam is added to forcibly
disable the PCM capabilities of the driver.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Old Soundscape cards (pre PnP) work only with AD1848 codecs.
If the CS4231 codec is installed it must be used in AD1848
compatible mode.
Also, add gameport support and remove an unused mpu field.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The conversion solves the problem that firmware size was set to 64KB
while non PnP cards have 128KB firmware files.
An additional firmware initialization code has been moved from the OSS
driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* topic/hda: (92 commits)
ALSA: hda - Use auto model for HP laptops with ALC268 codec
ALSA: hda/realtek: Added support for CLEVO M540R subsystem, 6 channel + digital
ALSA: hda - Add support of Alienware M17x laptop
ALSA: hda - Remove dead codes from patch_sigmatel.c
ALSA: hda - Fix input source selection of IDT92HD73xx
ALSA: hda - Fix obsolete CONFIG_SND_DEBUG_DETECT
ALSA: hda - Unmute docking line-out as default with AD1984A codec
ALSA: hda - Add another entry for Nvidia HDMI device
ALSA: hda - Add missing GPIO initialization for AD1984A laptop model
ALSA: hda - Add support of docking auto-mute/mic for AD1984A laptop model
ALSA: hda - Fix ALC268/ALC269 headphone pin routing
ALSA: hda - Create "Digital Mic Capture Volume" correctly for IDT codecs
ALSA: hda - Add more quirk for HP laptops with AD1984A
ALSA: hda - Add / fix model entries for HD-audio driver
ALSA: hda - Add full audio support on Acer Aspire 7730G notebook
ALSA: hda - Improve auto-cfg mixer name for ALC662
ALSA: hda - Improve auto-cfg mixer name for ALC861-VD
ALSA: hda - Improve auto-cfg mixer name for ALC262
ALSA: hda - Improve auto-cfg mixer name for ALC260
ALSA: hda - Improve auto-cfg mixer name for ALC880
...
Instead of allocating the real buffers, use a fake buffer and ignore
read/write in the dummy driver so that we can save the resources.
For mmap, a single page (unique to the direction, though) is reused
to all buffers.
When the app requires to read/write the real buffers, pass fake_buffer=0
module option at loading time. This will get back to the old behavior.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add debug module option to snd core.
This controls the debug print level. When CONFIG_SND_DEBUG_VERBOSE
is set, you can suppress the debug messages by giving or changing this
parameter to a lower value. debug=0 means no debug messsages.
As default, it's set to the verbose level 2.
Since this option can be changed dynamically via sysfs file, you can
suppress the verbose debug messages on the fly, which wasn't possible
before.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* topic/oxygen:
sound: virtuoso: add Xonar Essence ST support
sound: virtuoso: enable HDAV S/PDIF input
sound: virtuoso: add another DX PCI ID
sound: oxygen: reset DMA when stream is closed
* topic/maya44:
ALSA: ice1724 - Add ESI Maya44 support
ALSA: ice1724 - Allow spec driver to create own routing controls
ALSA: ice1724 - Add PCI postint to reset sequence
ALSA: ice1724 - Clean up definitions of DMA records
ALSA: ice1724 - Check error in set_rate function
Add support for the Asus Xonar Essence ST and its daughterboard.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add module parameter to enable or disable
joystick port (gameport) on the SC6600 and
later cards.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Masanari Iida