Ensure that BLK_DEV_IDE is built-in before allowing BLK_DEV_IDE_PMAC to
be selected.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Cc: Bret Towe <magnade@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add Toshiba S1800-814 to whitelist for both pata_ali and alim15x3,
as it is correctly detected as 40-wire connected but this cable is
short enough to still use transfer modes higher than UDMA33.
Signed-off-by: Daniel Exner <dex@dragonslave.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The Marvell bridge chips used on HighPoint SATA cards do not seem to support
the UltraDMA modes 1, 2, and 3 as well as any MWDMA modes, so the driver needs
to account for this in the udma_filter() method. In order to achieve that, do
the following changes:
- install the method for all chips, not only HPT36x/370 and improve the code
formatting by killing the extra tabs while at it;
- add to the end of the 'switch' statement in the method cases for HPT372[AN]
and HPT374 chips upon which the known SATA cards are based;
- use hwif->ultra_mask as a default mask for the ide_dma_filter() method to
behave correctly;
- move the HPT370[A] cases below the HPT36x case for consistency.
While at it, replace the explicit UltraDMA mode masks with ATA_UDMA* constants
all over the driver...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bob Ham <rah@bash.sh>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make the SATA drive detection code from eighty_ninty_three() into inline
ide_dev_is_sata() helper fixing it along the way to be more strict while
checking word 80 for the reserved values...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
HPT374 BIOS seems to only save f_CNT register value for the function #0 before
re-tuning DPLL (that causes the driver to report obviously distorted f_CNT for
the function #1) -- fix this by always reading the saved f_CNT register value
from the function #0 in the driver's init_chipset() method.
While at it, introduce 'chip_type' for holding the 'struct hpt_info' field
of the same name and replace the structure assignment with memcpy()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver erroneously "lets go" the mate IDE chip in init_setup_pdc20270()
when ide_setup_pci_devices() call succeeds -- fix this, and drop a couple of
useless assignments in this function while at it...
Bart: keep "findev" variable initialization to silence gcc
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The IDE core never marked the PCI IDE devices as being in use after succesfull
driver probe call (the devices were marked in use only while being probed), and
so was susceptible to issues caused by unsolicited PCI hotplug device removal.
So, add pci_dev_get() call to ide_scan_pcidev() and convert this function to
the kernel style, also dropping a bunch of useless curly braces from its caller,
ide_scan_pcibus() and somewhat beautifying printk() call there, while at it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Currently the mpc8xx ide driver will only work on arch/ppc so only
allow it to be built there. Also, killed a minor include that isn't
actually used by the driver.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
PCI: irq and pci_ids patch for Intel Tolapai
PCI: unhide SMBus on Compaq Deskpro EP 401963-001 motherboard
PCI: Remove __devinit from pcibios_get_irq_routing_table
PCI: remove devinit from pci_read_bridge_bases
PCI AER: fix warnings when PCIEAER=n
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: drivers/usb/serial/bus.c: Fix incompatible pointer type warning
USB: another quirky device (LCD display)
USB: fix serial gadget ACM breakage
USB: More USB_QUIRK_RESET_RESUME devices
USB Mass Storage: limit "Rockchip ROCK MP3" device (071b:3203) max I/O to 64 sectors per command
USB: Nikon D40 Quirks
USB: Add Sony Ericsson P1i to unusual_devs.h
USB: option: Add Dell HSDPA 5520 to driver
USB: option: Add a new device ID for the HUAWEI E220 HSDPA modem.
USB: fix linked list insertion bugfix for usb core
USB: quirky flash drive
USB: prevent Genesys USB-IDE from autosuspending
USB: prevent Thomson card reader from autosuspending
USB: Add iPhone device id to the quirk list.
USB: ftdi_sio: add of a new product/manufacturer, TML
usb/misc/sisusbvga: add product ID of TARGUS/MCT device
USB: oti6858: Remove broken ioctl code in -mm tree and also the broken fixes
This patch fixes a bug in AT91 mmc host driver, that enables the wakeup
from suspend on card detection pin even if the card detect pin is not
available (==0). If not card detection pin is defined, IRQ0 == FIQ gets
enabled and if some activity is present on that pin, the system gets a
FIQ request, that causes a crash.
Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee>
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
drivers/usb/serial/bus.c: In function usb_serial_bus_deregister:
drivers/usb/serial/bus.c:185:
warning: passing argument 1 of free_dynids from incompatible pointer type
Above build warning comes when CONFIG_HOTPLUG=n because argument of
free_dynids() in serial/bus.c is a struct usb_serial_driver, not a
struct usb_driver. This is not a runtime bug, because the function
is an empty stub and never dereferences the passed pointer anyway.
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Two of the CDC ACM control requests in the serial gadget have never
been correct, and have been reported to cause serious troubles ... as
in, soft lockup and maybe watchdog reset (depending on hardware).
This patch makes those request fail cleanly, rather than misbehaving.
Someone using CDC ACM should fix them according to the FIXME comments
which now replace the previous bugs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I would like have the attached patch added to Linux kernel. The three
usb flash memories listed in the patch are being used in Intel's
ClassmatePC and need USB_QUIRK_RESET_RESUME to work reliably when
resuming from ram.
The MP3/MP4/AVI player "Rockchip ROCK MP3" is seen as a USB disk, but fails
if more than 128 sectors (64kB) are sent or requested in a single read or write
command, and disconnects from the USB bus.
Typical kernel log showing the problem is:
usb 3-1: reset high speed USB device using ehci_hcd and address 6
usb 3-1: reset high speed USB device using ehci_hcd and address 6
sd 14:0:0:0: [sdb] Result: hostbyte=0x07 driverbyte=0x00
end_request: I/O error, dev sdb, sector 32
sd 14:0:0:0: [sdb] Result: hostbyte=0x07 driverbyte=0x00
end_request: I/O error, dev sdb, sector 32
usb 3-1: USB disconnect, address 6
This patch works around the device limitation by adding "Rockchip ROCK MP3"
to unusual USB devices list and limiting data transfers to 64 sectors (32kB)
per command.
Tested on 2.6.23-rc5 (amd64).
Signed-off-by: Massimiliano Ghilardi <massimiliano.ghilardi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The D40 needs the same quirks as the other (semi-)professional Nikon cameras.
The patch is against 2.6.23-rc5.
Details:
http://bugs.gentoo.org/show_bug.cgi?id=191431
From: Ortwin Glück <odi@odi.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is based on information sent in by Christian Gothe.
Cc: Christian Gothe <christian.gothe@kapelan.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the order of list_add_tail() arguments in
usb_store_new_id() so the list can have more than one single element.
Signed-off-by: Nathael Pajani <nathael.pajani@cpe.fr>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
That drive is quite odd. It has 2K sectors, times out getting string
descriptors and needs a quirk.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as986) prevents the troublesome Genesys USB-IDE adapter
from autosuspending. It may not be necessary for all such devices,
but the one in Bugzilla #8892 sometimes fails to resume.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as985) prevents the SGS THomson Microelectronics 4in1 card
reader from autosuspending. This resolves Bugzilla #8885.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I have added to a new product based on the FTDI 232R USB/Serial
transceiver, which is commercialized by The Mobility Lab. Here is a
trivial patch enclosed, against 2.6.22.6 kernel.
Signed-off-by: Pierre Castella <pp.castella@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Device is Targus ACP50US which includes a Magic Control Technologies
usb vga device using the SiS315(E) or compatible.
Signed-off-by: Samson Yeung <fragmede@onepatchdown.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This stuff is simply not needed.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[INET_DIAG]: Fix oops in netlink_rcv_skb
[IPv6]: Fix NULL pointer dereference in ip6_flush_pending_frames
[NETFILTER]: Fix/improve deadlock condition on module removal netfilter
[NETFILTER]: nf_conntrack_ipv4: fix "Frag of proto ..." messages
[NET] DOC: Update networking/multiqueue.txt with correct information.
[IPV6]: Freeing alive inet6 address
[DECNET]: Fix interface address listing regression.
[IPV4] devinet: show all addresses assigned to interface
[NET]: Do not dereference iov if length is zero
[TG3]: Workaround MSI bug on 5714/5780.
[Bluetooth] Fix parameter list for event filter command
[Bluetooth] Update security filter for Bluetooth 2.1
[Bluetooth] Add compat handling for timestamp structure
[Bluetooth] Add missing stat.byte_rx counter modification
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] libiscsi: sync up iscsi and scsi eh's access to the connection
[SCSI] libiscsi: fix null ptr regression when aborting a command with data to transfer
[SCSI] qla2xxx: Update version number to 8.02.00-k3.
[SCSI] qla2xxx: Correct mailbox register dump for FWI2 capable ISPs.
[SCSI] qla2xxx: Correct 8GB iIDMA support.
[SCSI] qla2xxx: Correct management-server login-state synchronization issue.
[SCSI] qla2xxx: Don't modify parity bits during ISP25XX restart.
[SCSI] qla2xxx: Allocate enough space for the full PCI descriptor.
[SCSI] zfcp: fix the data buffer accessor patch
[SCSI] zfcp: allocate gid_pn_data objects from gid_pn_cache
[SCSI] zfcp: fix memory leak
PCI quirk to unhide SMBus on Compaq Deskpro EP 401963-001 (PCA# 010174) motherboard.
Signed-off-by: Greg White <gw.kernel@tnode.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On MIPS with PCI && !HOTPLUG, I'm currently getting the following modpost
warning:
MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0x1ce128): Section mismatch: reference to .init.text:pci_read_bridge_bases (between 'pcibios_fixup_bus' and 'pcibios_enable_device')
On MIPS I have the call chains pci_scan_child_bus -> pcibios_fixup_bus ->
pci_read_bridge_bases. pci_scan_child_bus can't be __devinit because it
it is an exported symbol, thus pcibios_fixup_bus and pci_read_bridge_bases
can't be either.
For some reason I don't see this issue on x86; I blame compiler differences.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A hardware bug was revealed after a recent PCI MSI patch was made to
always disable legacy INTX when enabling MSI. The 5714/5780 chips
will not generate MSI when INTX is disabled, causing MSI failure
messages to be reported, and another patch was made to workaround the
problem by disabling MSI on ServerWorks HT1000 bridge chips commonly
found with the 5714.
We workaround this chip bug by enabling INTX after we enable MSI and
after we resume from suspend.
Update version to 3.81.
This problem was discovered by David Miller.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev->horkage should be cleared over device hotunplug/plug. Clear it
in ata_dev_init().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix "lost" interrupt problem when using dma with CD/DVD drives in some
configurations. This problem can make installing linux from media
impossible for distro's that have switched to libata-only configurations.
The simple fix is to eliminate the use of dma for reading drive status, etc,
by checking the number of bytes to transferred.
This change will only affect the behavior of atapi devices, not disks.
There is more info at http://bugzilla.redhat.com/show_bug.cgi?id=242229
This patch is for 2.6.22.1
Signed-off-by: Jeff Norden <jnorden@math.tntech.edu>
Reviewed-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c-algo-bit: Read block data bugfix
i2c-pxa: Fix adapter number
i2c-gpio: Fix adapter number
This fixes a bug in the way i2c-algo-bit handles I2C_M_RECV_LEN,
used to implement i2c_smbus_read_block_data(). Previously, in the
absence of PEC (rarely used!) it would NAK the "length" byte:
S addr Rd [A] [length] NA
That prevents the subsequent data bytes from being read:
S addr Rd [A] [length] { A [data] }* NA
The primary fix just reorders two code blocks, so the length used
in the "should I NAK now?" check incorporates the data which it
just read from the slave device.
However, that move also highlighted other fault handling glitches.
This fixes those by abstracting the RX path ack/nak logic, so it
can be used in more than one location. Also, a few CodingStyle
issues were also resolved.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
It turns out that platform_device.id is a "u32" so testing it for being
nonnegative is useless when setting up an i2c adapte. Instead,
do what the platform_bus code does and test it against the value "-1".
Signed-off-by: Jean Delvare <khali@linux-fr.org>
It turns out that platform_device.id is a "u32" so testing it for being
nonnegative is useless when setting up an i2c bitbang device. Instead,
do what the platform_bus code does and test it against the value "-1".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix an off-by-one error in the I/O region declaration of two
hardware monitoring drivers (lm78 and w83781d.) We were requesting
one extra port at the end of the region.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
With the support for hci_recv_fragment() the call to increase the
stat.byte_rx counter got accidentally removed. This patch fixes it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fixes (papers over) "Sleep problems with kernels >= 2.6.21 on powerpc",
http://lkml.org/lkml/2007/8/25/155. The issue is that the FireWire
controller's pci_dev.current_state of iBook G3 and presumably older
PowerBooks is still in PCI_UNKNOWN instead of PCI_D0 when the firewire
driver's .suspend method is called.
Like it was suggested earlier in http://lkml.org/lkml/2006/10/24/13, we
do not fail .suspend anymore if pci_set_power_state failed.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This patch fixes a nasty typo in usbtouchscreen driver. The typo
is inherited from the original mtouchusb. It used to make the input
subsytem to incorrectly report the physical device ids to userspace
that in turn is very confusing for, e.g. XInput hotplug facilities
in setups with multiple identical touchscreens.
Signed-off-by: Vladimir Shebordaev <vshebordaev@mail.ru>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This fixes "atkbd.c: Suprious NAK on isa0060/serio0" errors for
HP Pavilion DV4270ca.
Signed-off-by: Elvis Pranskevichus <el@prans.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
i8042_unregister_ports's only caller i8042_remove is a __devexit function
so make it __devexit too.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
drivers/acpi/event.c:243: error: 'acpi_generate_netlink_event' undeclared
here (not in a function)
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
Initialise s_flags in get_sb_mtd_aux() from the flags parameter.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
I think that I've found and fixed the problem. There is a copy/paste bug in
vt6421_set_dma_mode() function which causes wrong values to be written to
PATA_UDMA_TIMING register.
This patch fixes a copy/paste bug that breaks DMA modes on VT6421 PATA port.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: SRQ fixes to enable IPoIB CM
IB/ehca: Fix Small QP regressions
The HPET clocksource in drivers/char/hpet.c was written as generic code
for ia64, but it is not yet ready to replace the native HPET clocksource
implementations that the i386/x86-64 architectures use.
On x86[-64], trying to register this clocksource results in potentially
multiple hpet-based clocksources being registered, and if the ia64 one
is chosen on x86_64 some users have experienced hangs.
Eventually all three architectures may end up using the same code, but
that is not the case right now.
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Paolo Ornati <ornati@fastwebnet.it>
Cc: Bob Picco <bob.picco@hp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
- cxgb3 engine microcode load
cxgb3 - Fix dev->priv usage
qeth: Drop ARP packages on HiperSockets interface with NOARP attribute.
qeth: provide specific message for OSA-adapters exclusively used
qeth: crash during reboot after failing online setting
qeth: Announce tx checksumming for qeth devices in TSO/EDDP mode
qeth: dont return the return values of void functions.
qeth: enforce a rate limit for inbound scatter gather messages
qeth: ungrouping a device must not be interruptible
netxen: fix crashes during module unload
netxen: Avoid firmware load in PCI probe
PS3: fix the bug that 'ifconfig down' would hang
IOC3: Program UART predividers.
Fix ehca SRQ support so that IPoIB connected mode works:
- Report max_srq > 0 if SRQ is supported
- Report "last wqe reached" asynchronous event when base QP dies;
this is required by the IB spec and IPoIB CM relies on receiving it
when cleaning up.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The new Small QP code had a few bugs that would also make it trigger
for non-Small QPs. Fix them.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] Bump driver versions
ata_piix: implement IOCFG bit18 quirk
libata: implement BROKEN_HPA horkage and apply it to affected drives
sata_promise: FastTrack TX4200 is a second-generation chip
pata_marvell: Add more identifiers
ata_piix: add Satellite U200 to broken suspend list
ata: add ATA_MWDMA* and ATA_SWDMA* defines
ata_piix: IDE mode SATA patch for Intel Tolapai
libata-core: Allow translation setting to fail
Load the engine microcode when an interface
is brought up, instead of of doing it when the module
is loaded.
Loosen up tight binding between the driver and the
engine microcode version.
There is no need for microcode update with T3A boards.
Fix the file naming.
Do a better job at logging the loading activity.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
cxgb3 used netdev_priv() and dev->priv for different purposes.
In 2.6.23, netdev_priv() == dev->priv, cxgb3 needs a fix.
This patch is a partial backport of Dave Miller's changes in the
net-2.6.24 git branch.
Without this fix, cxgb3 crashes on 2.6.23.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A network interface can get ARP packets even when the interface has
NOARP specified. In a HiperSockets environment this disturbs receiving
systems when packets are sent on the multicast queue. (E.g. TCP/IP on
z/VM issues messages reporting invalid data on the HiperSockets
interface.)
Qeth will no longer send ARP packets on HiperSockets interface when
interface has the NOARP attribute.
Signed-off-by: Klaus D. Wacker <kdwacker@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Exclusive usage of OSA-cards has been introduced. Even though Linux
does not make use of it, qeth should be prepared to receive a bad RC
for some initialization steps. A meaningful message is now given,
if an OSA-device is set online, even though the OSA-adapter is already
exclusively used by another host.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Online setting of a qeth device may fail for instance because of:
- out-of-memory condition when allocating qdio queues
- IDX ACTIVATE problem
- ...
Such a device is still returned in a driver_for_each_device loop
processed in qeth_reboot_event(), which calls
qeth_clear_qdio_buffers(). Make sure qeth_clear_output_buffer() is
called only, if the qdio queues have been successfully allocated
during initialization of a qeth device.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
TSO requires tx checksumming. For non GSO frames in TSO/EDDP mode we
have to manually calculate the checksum.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
under memory pressure scatter gather mode switching messages must be
rate limited.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Problem:
A recovery thread must not be active when device is removed.
In qeth_remove_device() an interruptible wait operation is used
to wait until a qeth recovery thread is finished. If a user really
interrupts the ungroup operation of a qeth device while a recovery
is running, cio and qeth are out of sync (device already removed
from cio, but kept in qeth). A following module unload of qeth
results in a kernel OOPS here.
Solution:
Do not allow interruption of ungroup operation to guarantee
finishing of a potentially running qeth recovery thread.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes two problems during driver unload. The pci_disable_device()
call is before firmware reload, causing reads and writes across PCI bus after
disabling device. Second problem is the register window was wrong during
firmware reload
Signed-off by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Loading firmware during PCI probe can lead to incorrect initialization,
rendering the card unusable until next reboot. This was introduced a while
ago as a workaround for firmware bug, a better workaround was submitted for
this a while ago. So removing original hack that loads firmware during probe.
Signed-off by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix the bug that 'ifconfig eth0 down' would hang up, reported by Stefan
Assmann <sassmann@suse.de>.
As we removed netif_poll_enable() from dev->open(), we should not use
netif_poll_disable() in dev->stop().
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
CC: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The IOC3 driver's UART detection bits used to rely on the the firmware
setting the UART pre-divider in a way that's apropriate for the 8250
driver which doesn't currently program this register. This happens
to work for the console but not rarely for additional ports.
While at it, also program the UART to RS-232 PIO mode; it the UART might
have been in mac-serial and/or DMA mode though that hasn't actually been
observed in practice.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We find that SB700 and SB800 use the same SMBus device ID as SB600, which is
0x4385, instead of the already submitted 0x4395.
Besides removing the wrong SB700 device ID, add SB800 support to kernel, by
renaming the PCI_DEVICE_ID_ATI_IXP600_SMBUS into
PCI_DEVICE_ID_ATI_SBX00_SMBUS.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix cut 'n paste bug in Atmel SPI driver.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Acked-by: David Brownell <david-b@pacbell.net>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Correct the name of the spi_txx9 driver (and their in-tree user)
instead of MODULE_ALIAS workaround. This would be preferable in the
long term.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update various SPI drivers so they properly support
- coldplug through "modprobe $(cat /sys/devices/.../modalias)"
- hotplug through "modprobe $(MODALIAS)"
The basic rule for platform, SPI, and (new style) I2C drivers is just
to make sure that modprobing the driver name works. In this case, all
the relevant drivers are platform drivers, and this patch either
(a) Changes the driver name, if no in-tree code would break;
this is simpler and thus preferable in the long term.
(b) Adds MODULE_ALIAS directives, when in-tree platforms declare
devices using the current driver name; less desirable.
Most systems will link SPI controller drivers statically, but
there's no point in being needlessly broken.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jean Delvare <khali@linux-fr.org>
Acked-by: Andrei Konovalov <akonovalov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We better select a font when the newport driver is a module or the user
experience might suffer.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some notebooks need bit18 of IOCFG to be cleared for the drive bay to
work even though the bit is NOOP according to the datasheet. This
patch implement IOCFG bit18 quirk and apply it to Clevo M570U.
http://bugzilla.kernel.org/show_bug.cgi?id=8051
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: D. Angelis <dangelis@beta-cae.gr>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some drives choke on READ_NATIVE_MAX_ADDRESS[_EXT]. Implement
ATA_HORKAGE_BROKEN_HPA and apply it to affected drives.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch corrects sata_promise to classify FastTrack TX4200
(DID 3515/3519) as a second-generation chip. Promise's partial-
source FT TX4200 driver confirms this classification.
Treating it as a first-generation chip causes several problems:
1. Detection failures. This is a recent regression triggered by
the hotplug-enabling changes in 2.6.23-rc1.
2. Various "failed to resume link for reset" warnings.
This patch fixes <http://bugzilla.kernel.org/show_bug.cgi?id=8936>.
Thanks to Stephen Ziemba for reporting the bug and for testing the fix.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Stephen Ziemba <sziemba@ecn.purdue.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Satellite U200 also shares the problem. Add it to the broken suspend
list. Original patch from John Schember.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: John Schember <john@nachtimwald.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[PKTGEN]: Remove write-only variable.
[NETFILTER]: xt_tcpudp: fix wrong struct in udp_checkentry
[NET_SCHED] sch_prio.c: remove duplicate call of tc_classify()
[BRIDGE]: Fix OOPS when bridging device without ethtool.
[BRIDGE]: Packets leaking out of disabled/blocked ports.
[TCP]: Allow minimum RTO to be configurable via routing metrics.
SCTP: Fix to handle invalid parameter length correctly
SCTP: Abort on COOKIE-ECHO if backlog is exceeded.
SCTP: Correctly disable listening when backlog is 0.
SCTP: Do not retransmit chunks that are newer then rtt.
SCTP: Uncomfirmed transports can't become Inactive
SCTP: Pick the correct port when binding to 0.
SCTP: Use net_ratelimit to suppress error messages print too fast
SCTP: Fix to encode PROTOCOL VIOLATION error cause correctly
SCTP: Fix sctp_addto_chunk() to add pad with correct length
SCTP: Assign stream sequence numbers to the entire message
SCTP: properly clean up fragment and ordering queues during FWD-TSN.
[PKTGEN]: Fix multiqueue oops.
[BNX2]: Add write posting comment.
[BNX2]: Use msleep().
Resend trying to remove 8-bit characters in the email.
This patch adds the Intel Tolapai IDE mode SATA controller DID's.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On some early drives (pre ATA1) this feature is not supported. If it
fails then we know the drive geometry is the hardware geometry and the
one we tried to set anyway so just carry on.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
acpi_get_devices() returns success if it did not find any device.
We have to check for this case.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Daniel Ritz <daniel.ritz-ml@swissonline.ch>
Tested-by: Luca <kronos.it@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the stack pointer is 0xc057a000, then the first stack page is at
0xc0579000 (the stack pointer is decremented before use). Not
calculating this correctly caused guests with CONFIG_DEBUG_PAGEALLOC=y
to be killed with a "bad stack page" message: the initial kernel stack
was just proceeding the .smp_locks section which
CONFIG_DEBUG_PAGEALLOC marks read-only when freeing.
Thanks to Frederik Deweerdt for the bug report!
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The dummy touchkit_ps2_detect() for the CONFIG_MOUSE_PS2_TOUCHKIT=n case
shouldn't be a global function.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We should not return IRQ_HANDLED if we didn't handle the interrupt.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add comment to explain why we cannot read back after chip reset
before delaying.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2.c (incorrectly) sets current->state directly to
TASK_UNINTERRUPTIBLE, without going through set_task_state(). However
all the code wants to do is an msleep so just make it do that instead...
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2bcf9dddeb8e79a4ba55bf191533f70f39ce
('ACPI: delete CONFIG_ACPI_PROCFS_SLEEP (again)')
was incomplete.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Without this, we get qla2xxx complaining about "ISP System Error".
What's happening here is the firmware is detecting a Xfer-ready from the
storage when in fact the data-direction for a mode-select should be a
write (DATA_OUT).
The following patch fixes the problem (typo). Verified by Brian, as
well.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Verified-by: Brian De Wolf <bldewolf@csupomona.edu>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC32]: Make flush_tlb_kernel_range() an inline function.
[SERIAL]: Fix 32-bit warnings in sunzilog.c and sunsu.c
[SPARC32]: Kill unused vars and macros from prom/console.c
[SPARC32]: Add __cmpdi2() libcall implementation ala. MIPS.
[VIDEO]: Do not prom_halt() in cg3 and bw2 device probe.
[SUNVDC]: Use slice 0xff on VD_DISK_TYPE_DISK.
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NET]: Mark Paul Moore as maintainer of labelled networking.
[VLAN/BRIDGE]: Fix "skb_pull_rcsum - Fatal exception in interrupt"
[ISDN]: Get rid of some pointless allocation casts in common and bsd comp.
[NET]: Avoid pointless allocation casts in BSD compression module
[IRDA]: Do not do pointless kmalloc return value cast in KingSun driver
[NET]: Fix crash in dev_mc_sync()/dev_mc_unsync()
[PPPOL2TP]: Fix endianness annotations.
[IOAT]: ioatdma needs to to play nice in a multi-dma-client world
[SLIP]: trivial sparse warning fix
[EQL]: sparse warning fix
[NET]: is_power_of_2 in net/core/neighbour.c
[TCP]: Describe tcp_init_cwnd() thoroughly in a comment.
[NET]: Fix IP_ADD/DROP_MEMBERSHIP to handle only connectionless
[KBUILD]: Sanitize tc_ematch headers.
[IPSEC] AH4: Update IPv4 options handling to conform to RFC 4302.
Sigh. Again an ACPI assault on the Thinkpad's Fn+F4 to suspend to RAM.
The default and text for CONFIG_THINKPAD_ACPI_INPUT_ENABLED were fixed
in -rc3, but now commit 14e04fb34f ("ACPI:
Schedule /proc/acpi/event for removal") introduces the ACPI_PROC_EVENT
config entry, and defaults it to 'n' to disable it again.
Change default to y, and add comment to make it clearer that n is for
future distros.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fix SLB initialization at boot time
[POWERPC] Fix undefined reference to device_power_up/resume
[POWERPC] cell: Update cell_defconfig for 2.6.23
[POWERPC] axonram: Do not delete gendisks queue in error path
[POWERPC] axonram: Module modification for latest firmware API changes
[POWERPC] cell: Support pinhole-reset on IBM cell blades
[POWERPC] spu_manage: Use newer physical-id attribute
[POWERPC] pasemi: Another IOMMU bugfix for 64K PAGE_SIZE
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
[PARISC] Add NOTES section
[PARISC] Use compat_sys_getdents
[PARISC] Do not allow STI_CONSOLE to be modular
[PARISC] Clean up sti_flush
[PARISC] Add dummy isa_(bus|virt)_to_(virt|bus) inlines
[PARISC] Add empty <asm-parisc/vga.h>
sti_flush is supposed to flush the caches so we can execute the STI rom
we copied to memory. Anything more than flush_icache_range is overkill.
Fixes a missing symbol when built as a module.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
resource_size_t can be either a u64 or a u32, and we can't
really know for sure, so when printing such a value out
always use long-long printf formatting and cast the argument
to that type.
Signed-off-by: David S. Miller <davem@davemloft.net>
Just give a normal kernel log message of the problem and
return failure.
Based upon a patch from Mark Fortescue.
Signed-off-by: David S. Miller <davem@davemloft.net>
While debugging issues with the VDS server I made the
driver use partition 2 to get at the whole disk since
this is the "whole disk" partition in the Sun disk
label.
We really should use slice 0xff which really means
the whole physical disk in the VIO disk protocol.
Otherwise things won't work well on a disk image
that doesn't have a proper disk label on it.
Signed-off-by: David S. Miller <davem@davemloft.net>
vmalloc() returns a void pointer - no need to cast the return value.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The general kernel memory allocation functions return void pointers
and there is no need to cast their return values.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc() returns a void pointer, so there is no need to cast it in
drivers/net/irda/kingsun-sir.c::kingsun_probe().
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the DMA engine has a multi-client interface, fix the ioatdma
driver to play along. At the same time, remove a couple of unnecessary
reads and writes.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function declared static in forward declaration, but not in actual code.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
More noodlin on long flights, patch bin. Sparse warning fix for eql.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rtc-rs5c348 SPI driver name doesn't match its module name, which
prevents it from properly hotplugging. There is only one in-tree user
of its driver, which is fixed by this patch too.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: Add ref-counting for sbp2 orbs (fix command abortion)
firewire: fix unloading of fw-ohci while devices are attached
ieee1394: sbp2: fix sbp2_remove_device for error cases
This handles the case where we get the status write before getting the
complete_transaction callback ("status write for unknown orb"). In
this case, we just assume that the initial orb pointer transaction
succeeded and finish the orb. To prevent the transaction callback
from touching freed memory, we ref-count the orb structures.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Fix panic in run_timer_softirq right after "modprobe -r firewire-ohci"
if a FireWire disk was attached and firewire-sbp2 loaded.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Bug found by Olaf Hering <olh@suse.de>:
sbp2util_remove_command_orb_pool requires a valid lu->hi pointer.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* 'agp-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6:
agp: balance ioremap checks
agp: Add device id for P4M900 to via-agp module
efficeon-agp leaks 'struct agp_bridge_data' in error paths of agp_efficeon_probe()
* 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: ioremap return value checks
drm/via: Fix dmablit when blit queue is full
drm_rmmap_ioctl(): remove dead code
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
myri10ge: update driver version to 1.3.2-1.269
myri10ge: use pcie_get/set_readrq
ehea: fix queue destructor
ehea: fix module parameter description
ehea: fix interface to DLPAR tools
sgiseeq: Fix return type of sgiseeq_remove
sky2 1.17
sky2: only bring up watchdog if link is active
sky2: clear PCI power control reg at startup
DM9000: fix interface hang under load
phy layer: fix genphy_setup_forced (don't reset)
Don't use GFP_DMA for zone allocation.
fix realtek phy id in forcedeth
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (30 commits)
ACPI: work around duplicate name "VID" problem on T61
acpiphp_ibm: add missing '\n' to error message
ACPI: add dump_stack() to trace acpi_format_exception programming errors
make drivers/acpi/scan.c:create_modalias() static
ACPI: Fix a warning of discarding qualifiers from pointer target type
ACPI: "ACPI handle has no context!" should be KERN_DEBUG
ACPI video hotkey: export missing ACPI video hotkey events via input layer
ACPI: Validate XSDT, use RSDT if XSDT fails
ACPI: /proc/acpi/thermal_zone trip points are now read-only, mark them as such
ACPI: fix ia64 allnoconfig build
PNP: remove null pointer checks
PNP: remove MODULE infrastructure
ISAPNP: removed unused isapnp_detected and ISAPNP_DEBUG
PNPACPI: remove unnecessary casts of "void *"
PNPACPI: simplify irq_flags()
PNP: fix up after Lindent
ACPI: enable GPEs before calling _WAK on resume
asus-laptop: Fix rmmod of asus_laptop
sony-laptop: call sonypi_compat_init earlier
sony-laptop: enable Vaio FZ events
...
patchset against 2.6.23-rc3.
corrects missing ioremap return checks and balancing on iounmap calls, integrated changes per list
recommendations on the original set of patches..
Signed-off-by: Scott Thompson <postfail <at> hushmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Current Linus tree fails to link on pmac32:
drivers/built-in.o: In function `pmac_wakeup_devices':
via-pmu.c:(.text+0x5bab4): undefined reference to `device_power_up'
via-pmu.c:(.text+0x5bb08): undefined reference to `device_resume'
drivers/built-in.o: In function `pmac_suspend_devices':
via-pmu.c:(.text+0x5c260): undefined reference to `device_power_down'
via-pmu.c:(.text+0x5c27c): undefined reference to `device_resume'
make[1]: *** [.tmp_vmlinux1] Error 1
changing CONFIG_PM > CONFIG_PM_SLEEP leads to:
drivers/built-in.o: In function `pmu_led_set':
via-pmu-led.c:(.text+0x5cdca): undefined reference to `pmu_sys_suspended'
via-pmu-led.c:(.text+0x5cdce): undefined reference to `pmu_sys_suspended'
drivers/built-in.o: In function `pmu_req_done':
via-pmu-led.c:(.text+0x5ce3e): undefined reference to `pmu_sys_suspended'
via-pmu-led.c:(.text+0x5ce42): undefined reference to `pmu_sys_suspended'
drivers/built-in.o: In function `adb_init':
(.init.text+0x4c5c): undefined reference to `pmu_register_sleep_notifier'
make[1]: *** [.tmp_vmlinux1] Error 1
So change even more places from PM to PM_SLEEP to allow linking.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Based on a patch from Peter Oruba, convert myri10ge to use pcie_get_readrq()
and pcie_set_readrq() instead of our own PCI calls and arithmetics.
These driver changes incorporate the proposed PCI-X / PCI-Express read byte
count interface. Reading and setting those values doesn't take place
"manually", instead wrapping functions are called to allow quirks for some
PCI bridges.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off by: Peter Oruba <peter.oruba@amd.com>
Based on work by Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Includes hcp_epas_dtor in eq/cq/qp destructors to unmap
HW register.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update the module parameter description of "use_mcs" to
show correct default value
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Userspace DLPAR tool expects decimal numbers to be written to
and read from sysfs entries.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver remove method needs to return an int not void. This was just
never noticed because usually this driver is not being built as a module.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Mark new version to track if current driver is in use.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This fixes the extra timer overhead that people were whining about
as a 2.6.23 regression.
Running the watchdog timer all the time is unneeded. Change it
to run only if link is up, and reduce frequency to save power.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make sure PCI register for PHY power gets cleared on boot, and make
sure to avoid any PCI posting problems.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When transferring data at full speed, the DM9000 network interface
sometimes stops sending/receiving data. Worse, ksoftirqd consumes
100% cpu and the net tx watchdog never triggers.
Fix by spin_lock_irqsave() in dm9000_start_xmit() to prevent the
interrupt handler from interfering.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Writing BMCR_RESET bit will reset MII_BMCR to default values. This is
clearly not what we want.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
IP32 doesn't even have a ZONE_DMA so no point in using GFP_DMA in any
IP32-specific device driver.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As noticed by Chuck Ebbert, commit c5e3ae8823
introduced a copy-paste typo, as realtek phy is 0x732 and not 0x1c1. Obvious
fix below suggested by Ayaz Abdulla.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This can only fix the problem that more than one video bus device
have the same AML name "VID".
ie. the proc I/F for the second "VID" video bus device is located under
/proc/acpi/video/VID1/...
As this is really rare and the ACPI proc I/F is a legacy feature that
we are planning to remove.
We won't provide a generic solution for this problem.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add missing \n to error in ibm_find_acpi_device.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Adrian Bunk <trivial@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Dump the stack so we can find the secretive caller to acpi_format_exception().
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch makes the needlessly global create_modalias() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Len Brown <len.brown@intel.com>
drivers/acpi/ec.c: In function `acpi_ec_ecdt_probe':
drivers/acpi/ec.c:873: warning: passing arg 1 of `acpi_get_devices' discards qualifiers from pointer target type
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
DM_MULTIPATH_RDAC uses SCSI API(s) and is for a SCSI device,
so add SCSI to its depends on to prevent build errors.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
[ Tested and Verified by Chandra Seetharaman ]
Acked-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ACPI 1.0 used an RSDT with 32-bit physical addresses.
ACPI 2.0 adds an XSDT with 32-bit physical addresses.
An ACPI 2.0 aware OS is supposed to use the XSDT
(when present) instead of the RSDT.
However, several systems have failed because the XSDT
contains NULL entries -- while it is missing pointers
to needed tables, such as SSDTs.
When we find an XSDT with NULL entries, discard it
and use the ACPI 1.0 RSDT instead.
http://bugzilla.kernel.org/show_bug.cgi?id=8630
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
drivers/acpi/event.c:238: error: conflicting types for ‘acpi_bus_generate_netlink_event’
include/acpi/acpi_bus.h:324: error: previous declaration of ‘acpi_bus_generate_netlink_event’ was here
Signed-off-by: Len Brown <len.brown@intel.com>
Remove some null pointer checks. Null pointers in these areas indicate
programming errors, and I think it's better to oops immediately rather
than return an error that is easily ignored.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Adam Belay <abelay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We don't support building any part of PNP as a module (*drivers* can be
modules, of course, but the PNP infrastructure itself can not). Since
MODULE will never be defined, remove the ifdefs and dead code.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Adam Belay <abelay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ISAPNP_DEBUG isn't used at all. isapnp_detected is set but never read.
So remove them both.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Adam Belay <abelay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove unnecessary casts of void pointers.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Adam Belay <abelay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
No need for a temporary variable; just return the flags once we know them.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Adam Belay <abelay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
More manual fixups after Lindent. No functional change.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Adam Belay <abelay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
It seems it's required to enable GPEs before _WAK. E.g. X60 triggers a
LID related GPE instead of doing a Notify in WAK. Now the GPE reaches the
kernel and the Notify for LID status change gets thrown from there.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The asus laptop driver conditionnaly registers leds in asus_led_register()
depending on their availability, but unconditionnaly unregisters them all at
exit time or when the module fails to load. Unregistering not registered leds
result in the following Oops. So we should check before unregistering.
[<c032d2f9>] do_page_fault+0x511/0x5e9
[<c032bae2>] error_code+0x6a/0x70
[<c026abf8>] device_unregister+0x26/0x32
[<f8864218>] led_classdev_unregister+0x58/0x94 [led_class]
[<f88a90f8>] asus_led_exit+0x17/0x41 [asus_laptop]
[<f88a91c9>] asus_laptop_exit+0xd/0x3f [asus_laptop]
[<c013cee1>] sys_delete_module+0x17b/0x1a2
[<c0106eae>] sysenter_past_esp+0x6b/0xa1
EIP: [<c026a9a3>] device_del+0xb/0x23a SS:ESP 0068:f594ef0c
Signed-off-by: Guillaume Chazarain <guichaz@yahoo.fr>
Signed-off-by: Len Brown <len.brown@intel.com>
sonypi_compat uses a kfifo that needs to be present before _SRS is
called to be able to cope with the IRQs triggered when setting
resources.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: don't check n_sectors during revalidation if zero
pata_via: Add Arima W730-K8 and other rebadgings
pata_sis: Add the FSC Amilo and friends
pata_pdc2027x: PLL detection fixes
libata: fix n_sectors failure handling during revalidation
kmalloc() hands us a void pointer, we don't need to cast it.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
sdhci: tell which spurious interrupt we got
sdhci: handle data interrupts during command
mmc: ignore bad max block size in sdhci
sdhci: be more cautious about block count register
drivers/mmc/core/host.c: kmalloc + memset conversion to kzalloc
drivers/mmc/core/bus.c: kmalloc + memset conversion to kzalloc
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
PCI: Run k8t_sound_hostbridge quirk only when needed
PCI: disable MSI on RX790
PCI: disable MSI on RD580
PCI: disable MSI on RS690
PCI: make pcie_get_readrq visible in pci.h
PCI: lets kill the 'PCI hidden behind bridge' message
pci/hotplug/cpqphp_ctrl.c: remove stale BKL use
PCI: Document pci_iomap()
PCI: quirk_e100_interrupt() called too early
PCI: Move prototypes for pci_bus_find_capability to include/linux/pci.h
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (35 commits)
usb: add PRODUCT, TYPE to usb-interface events
USB: resubmission unusual_devs modification for Nikon D80
usb quirks: Add Canon EOS 5D (PC Connection mode) to the autosuspend blacklist
USB: make EHCI initialize properly on PPC SOCs
UEAGLE: Remove sysfs files on error case
USB: fsl_usb2_udc: fix bug in processing setup requests
USB: g_file_storage: fix bug in DMA buffer handling
USB: update last_busy field correctly
USB: fix DoS in pwc USB video driver
USB: allow retry on descriptor fetch errors
USB: unkill cxacru atm driver
USB: Adding support for HTC Smartphones to ipaq
USB: another quirky device
USB: quirky mass storage device
USB: ohci, fix oddball gcc warning
usb-storage: fix bugs in the disconnect pathway
usb: typo in usb R8A66597 HCD config
USB: accept 1-byte Device Status replies, fixing some b0rken devices
USB: blacklist Samsung ML-2010 printer
usb-serial: fix oti6858.c segfault in termios handling
...
Whoever did the PCI revision patch slipped up on the it821x, and I
didn't spot this at the time either. They moved the check for the
errata from the 0x10 revision to 0x11. Put it back
This one is important for 2.6.23 final as in some cases bad things will
occur if 0x10 revision boards don't get the fixups.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a manual revert of 7c010de750,
a fix that broke another ASUS in 8909 and 8919.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Both ACPI_VIDEO_NOTIFY_SWITCH and ACPI_VIDEO_NOTIFY_PROBE
are valid for video bus devices only. Actually ACPI video output
device should never be notified for a output device switch/probe.
ACPI bus devices notify handler already has the code to
handle these kinds of events.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Schedule /proc/acpi/event for removal in 6 months.
Re-name acpi_bus_generate_event() to acpi_bus_generate_proc_event()
to make sure there is no confusion that it is for /proc/acpi/event only.
Add CONFIG_ACPI_PROC_EVENT to allow removal of /proc/acpi/event.
There is no functional change if CONFIG_ACPI_PROC_EVENT=y
Signed-off-by: Len Brown <len.brown@intel.com>
The previous events patch added a netlink event for every
user of the legacy /proc/acpi/event interface.
However, some users of /proc/acpi/event are really input events,
and they already report their events via the input layer.
Introduce a new interface, acpi_bus_generate_netlink_event(),
which is explicitly called by devices that want to repoprt
events via netlink. This allows the input-like events
to opt-out of generating netlink events. In summary:
events that are sent via netlink:
ac/battery/sbs
thermal
processor
thinkpad_acpi dock/bay
events that are sent via input layer:
button
video hotkey
thinkpad_acpi hotkey
asus_acpi/asus-laptop hotkey
sonypi/sonylaptop
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
static function dvb_net_sec declares input arg "pkt" as u8. However, the
same argument at dvb_net_sec_callback is defined as "const u8". When
calling dvb_net_sec, this is casted as just "u8".
gcc 4.2.1 generates a warning about that:
CC [M] drivers/media/dvb/dvb-core/dvb_net.o
drivers/media/dvb/dvb-core/dvb_net.c: In function "dvb_net_sec_callback":
drivers/media/dvb/dvb-core/dvb_net.c:905: warning: passing argument 2 of
"dvb_net_sec" discards qualifiers from pointer target type
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Git changeset 6bdcc6e6db dropped the
stand-alone lgh06xf module, whose functionality was absorbed into the
dvb-pll module. However, there was a minor difference between the code
in lgh06xf and dvb-pll, which caused a regression in b2c2-flexcop
devices using the LG-H06xF NIM.
dvb-pll will probe for the presence of an i2c pll chip by performing a
single byte read, the lgh06xf driver did not do this. Unfortunately, the
code in flexcop-i2c.c does not currently support 1 byte or 0 byte reads
as a probe. Such probes with the current code will always fail.
In order to work around this problem, and restore proper functionality
of the Airstar HD5000 device, this hack was created to make the probe
appear to succeed. The single byte read in dvb_pll_attach is the only
place where such a probe would ever occur, so this change is safe, and
will not affect any other devices.
Of course, if one knew how to actually perform the read operation, it
would be better to go that route. In the meantime, however, we must
apply this workaround, in order to prevent the regression that causes
tuning to fail on the Airstar HD5000 ATSC device.
Thanks to Jarod Wilson, who had originally reported this regression, and
to Geoffrey Hausheer, whose original workaround patch led us to find the
actual cause of the problem.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Cc: Geoffrey Hausheer <inli3epy93n@phracturedblue.com>
Acked-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
construct a more or less wall-clock time out of sched_clock(), by
using ACPI-idle's existing knowledge about how much time we spent
idling. This allows the rq clock to work around TSC-stops-in-C2,
TSC-gets-corrupted-in-C3 type of problems.
( Besides the scheduler's statistics this also benefits blktrace and
printk-timestamps as well. )
Furthermore, the precise before-C2/C3-sleep and after-C2/C3-wakeup
callbacks allow the scheduler to get out the most of the period where
the CPU has a reliable TSC. This results in slightly more precise
task statistics.
the ACPI bits were acked by Len.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Len Brown <len.brown@intel.com>
This fixes a regression from around 2.6.18, consistent_sync() will now BUG()
under these circumstances. The use of consistent_sync() was a hack, replacing
it's usage here with a new function, flush_ioremap_region().
Signed-off-by: Jared Hulbert <jaredeh@gmail.com>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If the initial configuration fails early, n_sectors is left at zero.
Checking against it during revalidation makes retried configuration
fail due to n_sectors mismatch. Ignore zero n_sectors during
revalidation.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
More cable funnies
Signed-off-by: Alan Cox <alan@redhat.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Previously I reported that the pata_pdc2027x PLL detection changes
in kernel 2.6.22 broke the driver on my PowerMac:
>pata_pdc2027x: Invalid PLL input clock 1691742kHz, give up!
This is followed by a number of errors and speed reduction
steps on the affected ports.
There are two bugs in pata_pdc2027x's PLL detection code:
1. The PLL counter's start value is read before the chip is
put in "test mode". Outside of test mode the counter is
halted, and on the PowerMac the counter is zero because
the chip hasn't been initialised by its BIOS.
The fix is to move the read of the start value to after
test mode is started, but before the mdelay() in test mode.
This also improves the precision of the PLL detection.
2. The code to compute the number of PLL decrements during the
mdelay() in test mode fails to consider that the PLL counter
only is 30 bits wide. If there is a wraparound, it will compute
an incorrect and much too large value. On the PowerMac, the
start count is zero, the end count is a large 30-bit value, so
wraparound occurs and an out of bounds PLL clock is detected.
The fix is to mask the (start - end) computation to 30 bits.
While debugging this I also noticed that pdc_read_counter()
reads the two halves of the 30-bit PLL counter as 16-bit values,
and then combines them as if the halves only are 15 bits wide.
To avoid confusion, the halves should be read as 15-bit values.
This patch implements all three changes. It fixes the PLL detection
failure on my PowerMac, and doesn't cause any regressions on an x86
with an identical card.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tony Breeds