TCP without FRTO would be in Loss state with small cwnd. FRTO,
however, leaves cwnd (typically) to a larger value which causes
ssthresh to become too large in case RTO is triggered again
compared to what conventional recovery would do. Because
consecutive RTOs result in only a single ssthresh reduction,
RTO+cumulative ACK+RTO pattern is required to trigger this
event.
A large comment is included for congestion control module writers
trying to figure out what CA_EVENT_FRTO handler should do because
there exists a remote possibility of incompatibility between
FRTO and module defined ssthresh functions.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously RETRANS bits were cleared on the entry to FRTO. We
postpone that into tcp_enter_frto_loss, which is really the
place were the clearing should be done anyway. This allows
simplification of the logic from a clearing loop to the head skb
clearing only.
Besides, the other changes made in the previous patches to
tcp_use_frto made it impossible for the non-SACKed FRTO to be
entered if other than the head has been rexmitted.
With SACK-enhanced FRTO (and Appendix B), however, there can be
a number retransmissions in flight when RTO expires (same thing
could happen before this patchset also with non-SACK FRTO). To
not introduce any jumpiness into the packet counting during FRTO,
instead of clearing RETRANS bits from skbs during entry, do it
later on.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
This interpretation comes from RFC4138:
"If the sender implements some loss recovery algorithm other
than Reno or NewReno [FHG04], the F-RTO algorithm SHOULD
NOT be entered when earlier fast recovery is underway."
I think the RFC means to say (especially in the light of
Appendix B) that ...recovery is underway (not just fast recovery)
or was underway when it was interrupted by an earlier (F-)RTO
that hasn't yet been resolved (snd_una has not advanced enough).
Thus, my interpretation is that whenever TCP has ever
retransmitted other than head, basic version cannot be used
because then the order assumptions which are used as FRTO basis
do not hold.
NewReno has only the head segment retransmitted at a time.
Therefore, walk up to the segment that has not been SACKed, if
that segment is not retransmitted nor anything before it, we know
for sure, that nothing after the non-SACKed segment should be
either. This assumption is valid because TCPCB_EVER_RETRANS does
not leave holes but each non-SACKed segment is rexmitted
in-order.
Check for retrans_out > 1 avoids more expensive walk through the
skb list, as we can know the result beforehand: F-RTO will not be
allowed.
SACKed skb can turn into non-SACked only in the extremely rare
case of SACK reneging, in this case we might fail to detect
retransmissions if there were them for any other than head. To
get rid of that feature, whole rexmit queue would have to be
walked (always) or FRTO should be prevented when SACK reneging
happens. Of course RTO should still trigger after reneging which
makes this issue even less likely to show up. And as long as the
response is as conservative as it's now, nothing bad happens even
then.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
FRTO controls cwnd when it still processes the ACK input or it
has just reverted back to conventional RTO recovery; the normal
rules apply when FRTO has reverted to standard congestion
control.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because TCP is not in Loss state during FRTO recovery, fast
recovery could be triggered by accident. Non-SACK FRTO is more
robust than not yet included SACK-enhanced version (that can
receiver high number of duplicate ACKs with SACK blocks during
FRTO), at least with unidirectional transfers, but under
extraordinary patterns fast recovery can be incorrectly
triggered, e.g., Data loss+ACK losses => cumulative ACK with
enough SACK blocks to meet sacked_out >= dupthresh condition).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since purpose is to reduce CWND, we prevent immediate growth. This
is not a major issue nor is "the correct way" specified anywhere.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FRTO detection did not care how ACK pattern affects to cwnd
calculation of the conventional recovery. This caused incorrect
setting of cwnd when the fallback becames necessary. The
knowledge tcp_process_frto() has about the incoming ACK is now
passed on to tcp_enter_frto_loss() in allowed_segments parameter
that gives the number of segments that must be added to
packets-in-flight while calculating the new cwnd.
Instead of snd_una we use FLAG_DATA_ACKED in duplicate ACK
detection because RFC4138 states (in Section 2.2):
If the first acknowledgment after the RTO retransmission
does not acknowledge all of the data that was retransmitted
in step 1, the TCP sender reverts to the conventional RTO
recovery. Otherwise, a malicious receiver acknowledging
partial segments could cause the sender to declare the
timeout spurious in a case where data was lost.
If the next ACK after RTO is duplicate, we do not retransmit
anything, which is equal to what conservative conventional
recovery does in such case.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handles RFC4138 shortcoming (in step 2); it should also have case
c) which ignores ACKs that are not duplicates nor advance window
(opposite dir data, winupdate).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Retransmission counter assumptions are to be changed. Forcing
reason to do this exist: Using sysctl in check would be racy
as soon as FRTO starts to ignore some ACKs (doing that in the
following patches). Userspace may disable it at any moment
giving nice oops if timing is right. frto_counter would be
inaccessible from userspace, but with SACK enhanced FRTO
retrans_out can include other than head, and possibly leaving
it non-zero after spurious RTO, boom again.
Luckily, solution seems rather simple: never go directly to Open
state but use Disorder instead. This does not really change much,
since TCP could anyway change its state to Disorder during FRTO
using path tcp_fastretrans_alert -> tcp_try_to_open (e.g., when
a SACK block makes ACK dubious). Besides, Disorder seems to be
the state where TCP should be if not recovering (in Recovery or
Loss state) while having some retransmissions in-flight (see
tcp_try_to_open), which is exactly what happens with FRTO.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case a latency spike causes more than one RTO, the later should not
cause the already reduced ssthresh to propagate into the prior_ssthresh
since FRTO declares all such RTOs spurious at once or none of them. In
treating of ssthresh, we mimic what tcp_enter_loss() does.
The previous state (in frto_counter) must be available until we have
checked it in tcp_enter_frto(), and also ACK information flag in
process_frto().
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moved comments out from the body of process_frto() to the head
(preferred way; see Documentation/CodingStyle). Bonus: it's much
easier to read in this compacted form.
FRTO algorithm and implementation is described in greater detail.
For interested reader, more information is available in RFC4138.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
FRTO spurious RTO detection algorithm (RFC4138) does not include response
to a detected spurious RTO but can use different response algorithms.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
FRTO was slightly too brave... Should only clear
TCPCB_SACKED_RETRANS bit.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reply to NETLINK_FIB_LOOKUP messages were misrouted back to kernel,
which resulted in infinite recursion and stack overflow.
The bug is present in all kernel versions since the feature appeared.
The patch also makes some minimal cleanup:
1. Return something consistent (-ENOENT) when fib table is missing
2. Do not crash when queue is empty (does not happen, but yet)
3. Put result of lookup
Signed-off-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oops, thinko. The test for accempting a RH0 was exatly the wrong way
around.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A security issue is emerging. Disallow Routing Header Type 0 by default
as we have been doing for IPv4.
Note: We allow RH2 by default because it is harmless.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
draft-nikander-esp-beet-mode-07.txt is not entirely clear on how the length
value of the pseudo header should be calculated, it states "The Header Length
field contains the length of the pseudo header, IPv4 options, and padding in
8 octets units.", but also states "Length in octets (Header Len + 1) * 8".
draft-nikander-esp-beet-mode-08-pre1.txt [1] clarifies this, the header length
should not include the first 8 byte.
This change affects backwards compatibility, but option encapsulation didn't
work until very recently anyway.
[1] http://users.piuha.net/jmelen/BEET/draft-nikander-esp-beet-mode-08-pre1.txt
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change to defer congestion control initialization.
If setsockopt() was used to change TCP_CONGESTION before
connection is established, then protocols that use sequence numbers
to keep track of one RTT interval (vegas, illinois, ...) get confused.
Change the init hook to be called after handshake.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a regression due to the patch "NFS: disconnect before retrying NFSv4
requests over TCP"
The assumption made in xprt_transmit() that the condition
"req->rq_bytes_sent == 0 and request is on the receive list"
should imply that we're dealing with a retransmission is false.
Firstly, it may simply happen that the socket send queue was full
at the time the request was initially sent through xprt_transmit().
Secondly, doing this for each request that was retransmitted implies
that we disconnect and reconnect for _every_ request that happened to
be retransmitted irrespective of whether or not a disconnection has
already occurred.
Fix is to move this logic into the call_status request timeout handler.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a race between netlink_dump_start() and netlink_release()
that can lead to the situation when a netlink socket with non-zero
callback is freed.
Here it is:
CPU1: CPU2
netlink_release(): netlink_dump_start():
sk = netlink_lookup(); /* OK */
netlink_remove();
spin_lock(&nlk->cb_lock);
if (nlk->cb) { /* false */
...
}
spin_unlock(&nlk->cb_lock);
spin_lock(&nlk->cb_lock);
if (nlk->cb) { /* false */
...
}
nlk->cb = cb;
spin_unlock(&nlk->cb_lock);
...
sock_orphan(sk);
/*
* proceed with releasing
* the socket
*/
The proposal it to make sock_orphan before detaching the callback
in netlink_release() and to check for the sock to be SOCK_DEAD in
netlink_dump_start() before setting a new callback.
Signed-off-by: Denis Lunev <den@openvz.org>
Signed-off-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Pavel Emelianov <xemul@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an oops first reported in mid 2006 - see
http://lkml.org/lkml/2006/8/29/358 The cause of this bug report is that
when an error is signalled on the socket, irda_recvmsg_stream returns
without removing a local wait_queue variable from the socket's sk_sleep
queue. This causes havoc further down the road.
In response to this problem, a patch was made that invoked sock_orphan on
the socket when receiving a disconnect indication. This is not a good fix,
as this sets sk_sleep to NULL, causing applications sleeping in recvmsg
(and other places) to oops.
This is against the latest net-2.6 and should be considered for -stable
inclusion.
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The way partial delivery is currently implemnted, it is possible to
intereleave a message (either from another steram, or unordered) that
is not part of partial delivery process. The only way to this is for
a message to not be a fragment and be 'in order' or unorderd for a
given stream. This will result in bypassing the reassembly/ordering
queues where things live duing partial delivery, and the
message will be delivered to the socket in the middle of partial delivery.
This is a two-fold problem, in that:
1. the app now must check the stream-id and flags which it may not
be doing.
2. this clearing partial delivery state from the association and results
in ulp hanging.
This patch is a band-aid over a much bigger problem in that we
don't do stream interleave.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to actually assign the determined mode to
rq->sadb_x_ipsecrequest_mode.
Noticed by Joe Perches.
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[BRIDGE]: Unaligned access when comparing ethernet addresses
[SCTP]: Unmap v4mapped addresses during SCTP_BINDX_REM_ADDR operation.
[SCTP]: Fix assertion (!atomic_read(&sk->sk_rmem_alloc)) failed message
[NET]: Set a separate lockdep class for neighbour table's proxy_queue
[NET]: Fix UDP checksum issue in net poll mode.
[KEY]: Fix conversion between IPSEC_MODE_xxx and XFRM_MODE_xxx.
[NET]: Get rid of alloc_skb_from_cache
sk_info_authunix is not being protected properly so the object that it
points to can be cache_put twice, leading to corruption.
We borrow svsk->sk_defer_lock to provide the protection. We should
probably rename that lock to have a more generic name - later.
Thanks to Gabriel for reporting this.
Cc: Greg Banks <gnb@melbourne.sgi.com>
Cc: Gabriel Barazer <gabriel@oxeva.fr>
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
compare_ether_addr() implicitly requires that the addresses
passed are 2-bytes aligned in memory.
This is not true for br_stp_change_bridge_id() and
br_stp_recalculate_bridge_id() in which one of the addresses
is unsigned char *, and thus may not be 2-bytes aligned.
Signed-off-by: Evgeny Kravtsunov <emkravts@openvz.org>
Signed-off-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Pavel Emelianov <xemul@openvz.org>
During the sctp_bindx() call to add additional addresses to the
endpoint, any v4mapped addresses are converted and stored as regular
v4 addresses. However, when trying to remove these addresses, the
v4mapped addresses are not converted and the operation fails. This
patch unmaps the addresses on during the remove operation as well.
Signed-off-by: Paolo Galtieri <pgaltieri@mvista.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In current implementation, LKSCTP does receive buffer accounting for
data in sctp_receive_queue and pd_lobby. However, LKSCTP don't do
accounting for data in frag_list when data is fragmented. In addition,
LKSCTP doesn't do accounting for data in reasm and lobby queue in
structure sctp_ulpq.
When there are date in these queue, assertion failed message is printed
in inet_sock_destruct because sk_rmem_alloc of oldsk does not become 0
when socket is destroyed.
Signed-off-by: Tsutomu Fujii <t-fujii@nb.jp.nec.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise the following calltrace will lead to a wrong
lockdep warning:
neigh_proxy_process()
`- lock(neigh_table->proxy_queue.lock);
arp_redo /* via tbl->proxy_redo */
arp_process
neigh_event_ns
neigh_update
skb_queue_purge
`- lock(neighbor->arp_queue.lock);
This is not a deadlock actually, as neighbor table's proxy_queue
and the neighbor's arp_queue are different queues.
Lockdep thinks there is a deadlock as both queues are initialized
with skb_queue_head_init() and thus have a common class.
Signed-off-by: David S. Miller <davem@davemloft.net>
In net poll mode, the current checksum function doesn't consider the
kind of packet which is padded to reach a specific minimum length. I
believe that's the problem causing my test case failed. The following
patch fixed this issue.
Signed-off-by: Aubrey.Li <aubreylee@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not blindly convert between IPSEC_MODE_xxx and XFRM_MODE_xxx just
by incrementing / decrementing because the assumption is not true any longer.
Signed-off-by: Kazunori MIYAZAWA <miyazawa@linux-ipv6.org>
Singed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Since this was added originally for Xen, and Xen has recently (~2.6.18)
stopped using this function, we can safely get rid of it. Good timing
too since this function has started to bit rot.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two device string comparison loops in arp_packet_match().
The first one goes byte-by-byte but the second one tries to be
clever and cast the string to a long and compare by longs.
The device name strings in the arp table entries are not guarenteed
to be aligned enough to make this value, so just use byte-by-byte
for both cases.
Based upon a report by <drraid@gmail.com>.
Signed-off-by: David S. Miller <davem@davemloft.net>
A packet which is being discarded because of no routes in the
forwarding path should not be counted as OutNoRoutes but as
InNoRoutes.
Additionally, on this occasion, a packet whose destinaion is
not valid should be counted as InAddrErrors separately.
Based on patch from Mitsuru Chinen <mitch@linux.vnet.ibm.com>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending a security context of 50+ characters in an ACQUIRE
message, following kernel panic occurred.
kernel BUG in xfrm_send_acquire at net/xfrm/xfrm_user.c:1781!
cpu 0x3: Vector: 700 (Program Check) at [c0000000421bb2e0]
pc: c00000000033b074: .xfrm_send_acquire+0x240/0x2c8
lr: c00000000033b014: .xfrm_send_acquire+0x1e0/0x2c8
sp: c0000000421bb560
msr: 8000000000029032
current = 0xc00000000fce8f00
paca = 0xc000000000464b00
pid = 2303, comm = ping
kernel BUG in xfrm_send_acquire at net/xfrm/xfrm_user.c:1781!
enter ? for help
3:mon> t
[c0000000421bb650] c00000000033538c .km_query+0x6c/0xec
[c0000000421bb6f0] c000000000337374 .xfrm_state_find+0x7f4/0xb88
[c0000000421bb7f0] c000000000332350 .xfrm_tmpl_resolve+0xc4/0x21c
[c0000000421bb8d0] c0000000003326e8 .xfrm_lookup+0x1a0/0x5b0
[c0000000421bba00] c0000000002e6ea0 .ip_route_output_flow+0x88/0xb4
[c0000000421bbaa0] c0000000003106d8 .ip4_datagram_connect+0x218/0x374
[c0000000421bbbd0] c00000000031bc00 .inet_dgram_connect+0xac/0xd4
[c0000000421bbc60] c0000000002b11ac .sys_connect+0xd8/0x120
[c0000000421bbd90] c0000000002d38d0 .compat_sys_socketcall+0xdc/0x214
[c0000000421bbe30] c00000000000869c syscall_exit+0x0/0x40
--- Exception: c00 (System Call) at 0000000007f0ca9c
SP (fc0ef8f0) is in userspace
We are using size of security context from xfrm_policy to determine
how much space to alloc skb and then putting security context from
xfrm_state into skb. Should have been using size of security context
from xfrm_state to alloc skb. Following fix does that
Signed-off-by: Joy Latten <latten@austin.ibm.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VLAN interface is created on top of a bridge interface and
netfilter is enabled to see the bridged packets, the packets can be
corrupted when passing through the netfilter code. This is caused by the
VLAN driver not setting the 'protocol' and 'nh' members of the sk_buff
structure. In general, this is no problem as the VLAN interface is mostly
connected to a physical ethernet interface which does not use the
'protocol' and 'nh' members. For a bridge interface, however, these
members do matter.
Signed-off-by: Jerome Borsboom <j.borsboom@erasmusmc.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pktgen module prevents suspend-to-disk. Fix.
Acked-by: "Michal Piotrowski" <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use put_unaligned to fix warnings about unaligned accesses.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The clusterip_config_find_get() already increases entries reference
counter, so there is no reason to do it twice in checkentry() callback.
This causes the config to be freed before it is removed from the list,
resulting in a crash when adding the next rule.
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the cases that slow_start_after_idle are meant to deal
with, it is almost a certainty that the congestion window
tests will think the connection is application limited and
we'll thus decrease the cwnd there too. This defeats the
whole point of setting slow_start_after_idle to zero.
So test it there too.
We do not cancel out the entire tcp_cwnd_validate() function
so that if the sysctl is changed we still have the validation
state maintained.
Signed-off-by: David S. Miller <davem@davemloft.net>
Userspace uses an integer for TCA_TCINDEX_SHIFT, the kernel was changed
to expect and use a u16 value in 2.6.11, which broke compatibility on
big endian machines. Change back to use int.
Reported by Ole Reinartz <ole.reinartz@gmx.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Beet mode looks for the beet pseudo header after the outer IP header,
which is wrong since that is followed by the ESP header. Additionally
it needs to adjust the packet length after removing the pseudo header
and point the data pointer to the real data location.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Beet mode decapsulation fails to properly set up the skb pointers, which
only works by accident in combination with CONFIG_NETFILTER, since in that
case the skb is fixed up in xfrm4_input before passing it to the netfilter
hooks.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
draft-nikander-esp-beet-mode-07.txt states "The padding MUST be filled
with NOP options as defined in Internet Protocol [1] section 3.1
Internet header format.", so do that.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Beet mode calculates an incorrect value for the transport header location
when IP options are present, resulting in encapsulation errors.
The correct location is 4 or 8 bytes before the end of the original IP
header, depending on whether the pseudo header is padded.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until this point we've accepted replay window settings greater than
32 but our bit mask can only accomodate 32 packets. Thus any packet
with a sequence number within the window but outside the bit mask would
be accepted.
This patch causes those packets to be rejected instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Incoming trancated packets are counted as not only InTruncatedPkts but
also InHdrErrors. They should be counted as InTruncatedPkts only.
Signed-off-by: Mitsuru Chinen <mitch@linux.vnet.ibm.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we receive an AppleTalk frame shorter than what its header says,
we still attempt to verify its checksum, and trip on the BUG_ON() at
the end of function atalk_sum_skb() because of the length mismatch.
This has security implications because this can be triggered by simply
sending a specially crafted ethernet frame to a target victim,
effectively crashing that host. Thus this qualifies, I think, as a
remote DoS. Here is the frame I used to trigger the crash, in npg
format:
<Appletalk Killer>
{
# Ethernet header -----
XX XX XX XX XX XX # Destination MAC
00 00 00 00 00 00 # Source MAC
00 1D # Length
# LLC header -----
AA AA 03
08 00 07 80 9B # Appletalk
# Appletalk header -----
00 1B # Packet length (invalid)
00 01 # Fake checksum
00 00 00 00 # Destination and source networks
00 00 00 00 # Destination and source nodes and ports
# Payload -----
0C 0D 0E 0F 10 11 12 13
14
}
The destination MAC address must be set to those of the victim.
The severity is mitigated by two requirements:
* The target host must have the appletalk kernel module loaded. I
suspect this isn't so frequent.
* AppleTalk frames are non-IP, thus I guess they can only travel on
local networks. I am no network expert though, maybe it is possible
to somehow encapsulate AppleTalk packets over IP.
The bug has been reported back in June 2004:
http://bugzilla.kernel.org/show_bug.cgi?id=2979
But it wasn't investigated, and was closed in July 2006 as both
reporters had vanished meanwhile.
This code was new in kernel 2.6.0-test5:
http://git.kernel.org/?p=linux/kernel/git/tglx/history.git;a=commitdiff;h=7ab442d7e0a76402c12553ee256f756097cae2d2
And not modified since then, so we can assume that vanilla kernels
2.6.0-test5 and later, and distribution kernels based thereon, are
affected.
Note that I still do not know for sure what triggered the bug in the
real-world cases. The frame could have been corrupted by the kernel if
we have a bug hiding somewhere. But more likely, we are receiving the
faulty frame from the network.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value of kernel_recvmsg() should be assigned to "err", not
compared with the random value of a never initialized "err" (and the "< 0"
check wrongly always returned false since == comparisons never have a
result < 0).
Spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The generic networking code ensures that no two networking devices
have the same name, so there is no time except when sysfs has
implementation bugs that device_rename when called from
dev_change_name will fail.
The current error handling for errors from device_rename in
dev_change_name is wrong and results in an unusable and unrecoverable
network device if device_rename is happens to return an error.
This patch removes the buggy error handling. Which confines the mess
when device_rename hits a problem to sysfs, instead of propagating it
the rest of the network stack. Making linux a little more robust.
Without this patch you can observe what happens when sysfs has a bug
when CONFIG_SYSFS_DEPRECATED is not set and you attempt to rename
a real network device to a name like (broken_parity_status, device,
modalias, power, resource2, subsystem_vendor, class, driver, irq,
msi_bus, resource, subsystem, uevent, config, enable, local_cpus,
numa_node, resource0, subsystem_device, vendor)
Greg has a patch that fixes the sysfs bugs but he doesn't trust it
for a 2.6.21 timeframe. This patch which just ignores errors should
be safe and it keeps the system from going completely wacky.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In article <20070329.142644.70222545.davem@davemloft.net> (at Thu, 29 Mar 2007 14:26:44 -0700 (PDT)), David Miller <davem@davemloft.net> says:
> From: Sridhar Samudrala <sri@us.ibm.com>
> Date: Thu, 29 Mar 2007 14:17:28 -0700
>
> > The check for length in rawv6_sendmsg() is incorrect.
> > As len is an unsigned int, (len < 0) will never be TRUE.
> > I think checking for IPV6_MAXPLEN(65535) is better.
> >
> > Is it possible to send ipv6 jumbo packets using raw
> > sockets? If so, we can remove this check.
>
> I don't see why such a limitation against jumbo would exist,
> does anyone else?
>
> Thanks for catching this Sridhar. A good compiler should simply
> fail to compile "if (x < 0)" when 'x' is an unsigned type, don't
> you think :-)
Dave, we use "int" for returning value,
so we should fix this anyway, IMHO;
we should not allow len > INT_MAX.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This changes the "not found" error return for the lookup
function to -ESRCH so that it can be distinguished from
the case where a rule or route resulting in -ENETUNREACH
has been found during the search.
It fixes a bug where if DECnet was compiled with routing
support, but no routes were added to the routing table,
it was failing to fall back to endnode routing.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Patrick Caulfield <pcaulfie@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The input_device pointer is not refcounted, which means the device may
disappear while packets are queued, causing a crash when ifb passes packets
with a stale skb->dev pointer to netif_rx().
Fix by storing the interface index instead and do a lookup where neccessary.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
I have a bugreport that scrollwheel of bluetooth version of apple
mightymouse doesn't work. The USB version of mightymouse works, as there
is a quirk for handling scrollwheel in hid/usbhid for it.
Now that bluetooth git tree is hooked to generic hid layer, it could easily
use the quirks which are already present in generic hid parser, hid-input,
etc.
Below is a simple patch against bluetooth git tree, which adds quirk
handling to current bluetooth hidp code, and sets quirk flags for device
0x05ac/0x030c, which is the bluetooth version of the apple mightymouse.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
SUN3/3X Lance trivial fix improved
mv643xx_eth: Fix use of uninitialized port_num field
forcedeth: fix tx timeout
forcedeth: fix nic poll
qla3xxx: bugfix: Jumbo frame handling.
qla3xxx: bugfix: Dropping interrupt under heavy network load.
qla3xxx: bugfix: Multi segment sends were getting whacked.
qla3xxx: bugfix: Add tx control block memset.
atl1: remove unnecessary crc inversion
myri10ge: correctly detect when TSO should be used
[PATCH] WE-22 : prevent information leak on 64 bit
[PATCH] wext: Add missing ioctls to 64<->32 conversion
[PATCH] bcm43xx: Fix machine check on PPC for version 1 PHY
[PATCH] bcm43xx: fix radio_set_tx_iq
[PATCH] bcm43xx: Fix code for confusion between PHY revision and PHY version
We were only checking if there was enough space to put the int, but
left len as specified by the (malicious) user, sigh, fix it by setting
len to sizeof(val) and transfering just one int worth of data, the one
asked for.
Also check for negative len values.
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We still need to set the IF_READY flag in ipv6_add_dev for the case
where all addresses (including the link-local) are deleted and then
recreated. In that case the IPv6 device too will be destroyed and
then recreated.
In order to prevent the original problem, we simply ensure that
the device is up before setting IF_READY.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
During both HTB and HFSC class deletion the class is removed from the
class hash before calling qdisc_tree_decrease_qlen. This makes the
->get operation in qdisc_tree_decrease_qlen fail, so it passes a NULL
pointer to ->qlen_notify, causing an oops.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg discovered that kernel space was leaking to
userspace on 64 bit platform. He made a first patch to fix that. This
is an improved version of his patch.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the worthless net/sched/Makefile entry for the non-existent
source file sch_hpfq.c.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul E. McKenney writes:
> Those of use who dive into networking only occasionally would much
> appreciate this. ;-)
No problem here...
Acked-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> (but trivial)
Signed-off-by: David S. Miller <davem@davemloft.net>
* d_alloc() in sock_attach_fd() fails leaving ->f_dentry of new file NULL
* bail out to out_fd label, doing fput()/__fput() on new file
* but __fput() assumes valid ->f_dentry and dereferences it
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ingress queueing uses a seperate lock for serializing enqueue operations,
but fails to properly protect itself against concurrent changes to the
qdisc tree. Use queue_lock for now since the real fix it quite intrusive.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
cls_basic doesn't allocate tp->root before it is linked into the
active classifier list, resulting in a NULL pointer dereference
when packets hit the classifier before its ->change function is
called.
Reported by Chris Madden <chris@reflexsecurity.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per RFC2461, section 6.3.6, item #2, when no routers on the
matching list are known to be reachable or probably reachable we
do round robin on those available routes so that we make sure
to probe as many of them as possible to detect when one becomes
reachable faster.
Each routing table has a rwlock protecting the tree and the linked
list of routes at each leaf. The round robin code executes during
lookup and thus with the rwlock taken as a reader. A small local
spinlock tries to provide protection but this does not work at all
for two reasons:
1) The round-robin list manipulation, as coded, goes like this (with
read lock held):
walk routes finding head and tail
spin_lock();
rotate list using head and tail
spin_unlock();
While one thread is rotating the list, another thread can
end up with stale values of head and tail and then proceed
to corrupt the list when it gets the lock. This ends up causing
the OOPS in fib6_add() later onthat many people have been hitting.
2) All the other code paths that run with the rwlock held as
a reader do not expect the list to change on them, they
expect it to remain completely fixed while they hold the
lock in that way.
So, simply stated, it is impossible to implement this correctly using
a manipulation of the list without violating the rwlock locking
semantics.
Reimplement using a per-fib6_node round-robin pointer. This way we
don't need to manipulate the list at all, and since the round-robin
pointer can only ever point to real existing entries we don't need
to perform any locking on the changing of the round-robin pointer
itself. We only need to reset the round-robin pointer to NULL when
the entry it is pointing to is removed.
The idea is from Thomas Graf and it is very similar to how this
was implemented before the advanced router selection code when in.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes a typo which caused fib_props[] to have the wrong size
and makes sure the value used to index the array which is
provided by userspace via netlink is checked to avoid out of
bound access.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes a typo which caused fib_props[] to have the wrong size
and makes sure the value used to index the array which is
provided by userspace via netlink is checked to avoid out of
bound access.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
o The AX.25 Howto is unmaintained since several years. I've replaced it
with a wiki at http://www.linux-ax25.org which provides more uptodate
information.
o Change default for AX25_DAMA_SLAVE to Y. AX25_DAMA_SLAVE only compiles
in support for DAMA but doesn't activate it. I hope this gets Linux
distributions to ship their AX.25 kernels with AX25_DAMA_SLAVE enabled.
The price for this would be very small.
o Delete historic changelog from comments, that's what SCM systems are
meant to do.
o ---help--- in Kconfig looks so yellingly eye insulting. Use just help.
o Rewrite the commented out piece of old Linux 2.4 configuration language
to Kconfig for consistency.
o Fixup dependencies.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
->neigh_destructor() is killed (not used), replaced with
->neigh_cleanup(), which is called when neighbor entry goes to dead
state. At this point everything is still valid: neigh->dev,
neigh->parms etc.
The device should guarantee that dead neighbor entries (neigh->dead !=
0) do not get private part initialized, otherwise nobody will cleanup
it.
I think this is enough for ipoib which is the only user of this thing.
Initialization private part of neighbor entries happens in ipib
start_xmit routine, which is not reached when device is down. But it
would be better to add explicit test for neigh->dead in any case.
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon a patch from Patrick McHardy.
The fib_rules netlink attribute policy introduced in 2.6.19 broke
userspace compatibilty. When specifying a rule with "from all"
or "to all", iproute adds a zero byte long netlink attribute,
but the policy requires all addresses to have a size equal to
sizeof(struct in_addr)/sizeof(struct in6_addr), resulting in a
validation error.
Check attribute length of FRA_SRC/FRA_DST in the generic framework
by letting the family specific rules implementation provide the
length of an address. Report an error if address length is non
zero but no address attribute is provided. Fix actual bug by
checking address length for non-zero instead of relying on
availability of attribute.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently NAT not only reroutes packets in the OUTPUT chain when the
routing key changed, but also if only the non-routing part of the
IPsec policy key changed. This breaks ping -I since it doesn't use
SO_BINDTODEVICE but IP_PKTINFO cmsg to specify the output device, and
this information is lost.
Only do full rerouting if the routing key changed, and just do a new
policy lookup with the old route if only the ports changed.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
NF_CT_NETLINK=y, NF_NAT=m results in:
LD .tmp_vmlinux1
net/built-in.o: dans la fonction « nfnetlink_parse_nat_proto »:
nf_conntrack_netlink.c:(.text+0x28db9): référence indéfinie vers « nf_nat_proto_find_get »
nf_conntrack_netlink.c:(.text+0x28dd6): référence indéfinie vers « nf_nat_proto_put »
net/built-in.o: dans la fonction « ctnetlink_new_conntrack »:
nf_conntrack_netlink.c:(.text+0x29959): référence indéfinie vers « nf_nat_setup_info »
nf_conntrack_netlink.c:(.text+0x29b35): référence indéfinie vers « nf_nat_setup_info »
nf_conntrack_netlink.c:(.text+0x29cf7): référence indéfinie vers « nf_nat_setup_info »
nf_conntrack_netlink.c:(.text+0x29de2): référence indéfinie vers « nf_nat_setup_info »
make: *** [.tmp_vmlinux1] Erreur 1
Reported by Kevin Baradon <kevin.baradon@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turning up the warnings on gcc makes it emit warnings
about the placement of 'inline' in function declarations.
Here's everything that was under net/
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset ssthresh to the correct value (peer's a_rwnd) when restarting
association.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_fdb_get use atomic_inc to increase the refcount of an element found
on a RCU protected list, which can lead to the following race:
CPU0 CPU1
br_fdb_get: rcu_read_lock
__br_fdb_get: find element
fdb_delete: hlist_del_rcu
br_fdb_put
br_fdb_put: atomic_dec_and_test
call_rcu(fdb_rcu_free) br_fdb_get: atomic_inc
rcu_read_unlock
fdb_rcu_free: kmem_cache_free
Use atomic_inc_not_zero instead.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_rules_dump needs to use list_for_each_entry_rcu to protect against
concurrent changes to the rules list.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a space between printing of the src and dst ipv6 addresses.
Otherwise, audit or other test tools may fail to process the audit
record properly because they cannot find the dst address.
Signed-off-by: Joy Latten <latten@austin.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes two NULL dereferences spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the association has been restarted, we need to reset the
transport congestion variables as well as accumulated error
counts and CACC variables. If we do not, the association
will use the wrong values and may terminate prematurely.
This was found with a scenario where the peer restarted
the association when lksctp was in the last HB timeout for
its association. The restart happened, but the error counts
have not been reset and when the timeout occurred, a newly
restarted association was terminated due to excessive
retransmits.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2960bis states (Section 8.3):
D) Request an on-demand HEARTBEAT on a specific destination transport
address of a given association.
The endpoint should increment the respective error counter of the
destination transport address each time a HEARTBEAT is sent to that
address and not acknowledged within one RTO.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During association restart we may have stale data sitting
on the ULP queue waiting for ordering or reassembly. This
data may cause severe problems if not cleaned up. In particular
stale data pending ordering may cause problems with receive
window exhaustion if our peer has decided to restart the
association.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to call ppp_unregister_channel() when IrNET disconnects, and this
must be done from a process context.
Bug reported and patch tested by Guennadi Liakhovetski.
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this initialization one gets
kernel BUG at kernel/rtmutex_common.h:80!
This patch should also be included in the -stable kernel.
Signed-off-by: G. Liakhovetski <gl@dsa-ac.de>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipv6_fl_socklist from listening socket is inadvertently shared
with new socket created for connection. This leads to a variety of
interesting, but fatal, bugs. For example, removing one of the
sockets may lead to the other socket's encountering a page fault
when the now freed list is referenced.
The fix is to not share the flow label list with the new socket.
Signed-off-by: Masayuki Nakagawa <nakagawa.msy@ncos.nec.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change tcp_mem initialization function. The fraction of total memory
is now a continuous function of memory size, and independent of page
size.
Signed-off-by: John Heffner <jheffner@psc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
ANK says: "It is rarely used, that's wy it was not noticed.
But in the places, where it is used, it should be disaster."
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hello, Just discussed this Patrick...
We have two users of trie_leaf_remove, fn_trie_flush and fn_trie_delete
both are holding RTNL. So there shouldn't be need for this preempt stuff.
This is assumed to a leftover from an older RCU-take.
> Mhh .. I think I just remembered something - me incorrectly suggesting
> to add it there while we were talking about this at OLS :) IIRC the
> idea was to make sure tnode_free (which at that time didn't use
> call_rcu) wouldn't free memory while still in use in a rcu read-side
> critical section. It should have been synchronize_rcu of course,
> but with tnode_free using call_rcu it seems to be completely
> unnecessary. So I guess we can simply remove it.
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
I noticed that in xfrm_state_add we look for the larval SA in a few
places without checking for protocol match. So when using both
AH and ESP, whichever one gets added first, deletes the larval SA.
It seems AH always gets added first and ESP is always the larval
SA's protocol since the xfrm->tmpl has it first. Thus causing the
additional km_query()
Adding the check eliminates accidental double SA creation.
Signed-off-by: Joy Latten <latten@austin.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delete the apparently superfluous source file
net/wanrouter/af_wanpipe.c.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kill warning about unused variable `in_dev' when CONFIG_IP_MULTICAST
is not set.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 484b366932 added support for the CIPSO
ranged categories tag. However, it appears that I made a mistake when rebasing
then patch to the latest upstream sources for submission and dropped the part
of the patch that actually parses the tag on incoming packets. This patch
fixes this mistake by adding the required function call to the
cipso_v4_skbuff_getattr() function.
I've run this patch over the weekend and have not noticed any problems.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
User supplied len < 0 can cause leak of kernel memory.
Use unsigned compare instead.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I came across this bug in http://bugzilla.kernel.org/show_bug.cgi?id=8155
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX CCID needs the write_xmit_timer for delaying packet sends. Previously
this timer was only activated on active (connecting) sockets.
This patch initialises the write_xmit_timer in sync with the other timers, i.e.
the timer will be ready on any socket. This is used by applications with a
listening socket which start to stream after receiving an initiation by the
client. The write_xmit_timer is stopped when the application closes, as before.
Was tested to work and to remove the timer bug reported on dccp@vger.
Also moved timer initialisation into timer.c (static).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return negative error value (embedded in the pointer) instead of
returning NULL.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
lockdep found that dev->lock taken from softirq in ipv6_add_addr
is also taken in sctp_v6_copy_addrlist with softirqs enabled, so
lockup is possible.
Noticed-by: Simon Arlott <simon@arlott.org>
Signed-off-by: Jarek Poplawski <jarkao2@o2.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
[Bluetooth] Fix socket locking in hci_sock_dev_event()
hci_sock_dev_event() uses bh_lock_sock() to lock the socket lock.
This is not deadlock-safe against locking of the same socket lock in
l2cap_connect_cfm() from softirq context. In addition to that,
hci_sock_dev_event() doesn't seem to be called from softirq context,
so it is safe to use lock_sock()/release_sock() instead.
The lockdep warning can be triggered on my T42p simply by switching
the Bluetooth off by the keyboard button.
=================================
[ INFO: inconsistent lock state ]
2.6.21-rc2 #4
---------------------------------
inconsistent {in-softirq-W} -> {softirq-on-W} usage.
khubd/156 [HC0[0]:SC0[0]:HE1:SE1] takes:
(slock-AF_BLUETOOTH){-+..}, at: [<e0ca5520>] hci_sock_dev_event+0xa8/0xc5 [bluetooth]
{in-softirq-W} state was registered at:
[<c012d1db>] mark_lock+0x59/0x414
[<e0cef688>] l2cap_connect_cfm+0x4e/0x11f [l2cap]
[<c012dfd7>] __lock_acquire+0x3e5/0xb99
[<e0cef688>] l2cap_connect_cfm+0x4e/0x11f [l2cap]
[<c012e7f2>] lock_acquire+0x67/0x81
[<e0cef688>] l2cap_connect_cfm+0x4e/0x11f [l2cap]
[<c036ee72>] _spin_lock+0x29/0x34
[<e0cef688>] l2cap_connect_cfm+0x4e/0x11f [l2cap]
[<e0cef688>] l2cap_connect_cfm+0x4e/0x11f [l2cap]
[<e0ca17c3>] hci_send_cmd+0x126/0x14f [bluetooth]
[<e0ca4ce4>] hci_event_packet+0x729/0xebd [bluetooth]
[<e0ca205b>] hci_rx_task+0x2a/0x20f [bluetooth]
[<e0ca209d>] hci_rx_task+0x6c/0x20f [bluetooth]
[<c012d7be>] trace_hardirqs_on+0x10d/0x14e
[<c011ac85>] tasklet_action+0x3d/0x68
[<c011abba>] __do_softirq+0x41/0x92
[<c011ac32>] do_softirq+0x27/0x3d
[<c0105134>] do_IRQ+0x7b/0x8f
[<c0103dec>] common_interrupt+0x24/0x34
[<c0103df6>] common_interrupt+0x2e/0x34
[<c0248e65>] acpi_processor_idle+0x1b3/0x34a
[<c0248e68>] acpi_processor_idle+0x1b6/0x34a
[<c010232b>] cpu_idle+0x39/0x4e
[<c04bab0c>] start_kernel+0x372/0x37a
[<c04ba42b>] unknown_bootoption+0x0/0x202
[<ffffffff>] 0xffffffff
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One change introduced by the workqueue removal patch is that adding an
interface that is up to a bridge which is also up does not ever call
br_stp_enable_port(), leaving the port in DISABLED state until we do
ifconfig down and up or link events occur.
The following patch to the br_add_if function fixes it.
This is a regression introduced in 2.6.21.
Submitted-by: Aji_Srinivas@emc.com
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we add the IPv6 device at registration time we don't need
to set IF_READY in ipv6_add_dev anymore because we will always get
a NETDEV_UP event later on should the device ever become ready.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inside pfkey_delete and xfrm_del_sa the audit hooks were not called if
there was any permission/security failures in attempting to do the del
operation (such as permission denied from security_xfrm_state_delete).
This patch moves the audit hook to the exit path such that all failures
(and successes) will actually get audited.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Venkat Yekkirala <vyekkirala@trustedcs.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
pfkey_spdget neither had an LSM security hook nor auditing for the
removal of xfrm_policy structs. The security hook was added when it was
moved into xfrm_policy_byid instead of the callers to that function by
my earlier patch and this patch adds the auditing hooks as well.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Venkat Yekkirala <vyekkirala@trustedcs.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The security hooks to check permissions to remove an xfrm_policy were
actually done after the policy was removed. Since the unlinking and
deletion are done in xfrm_policy_by* functions this moves the hooks
inside those 2 functions. There we have all the information needed to
do the security check and it can be done before the deletion. Since
auditing requires the result of that security check err has to be passed
back and forth from the xfrm_policy_by* functions.
This patch also fixes a bug where a deletion that failed the security
check could cause improper accounting on the xfrm_policy
(xfrm_get_policy didn't have a put on the exit path for the hold taken
by xfrm_policy_by*)
It also fixes the return code when no policy is found in
xfrm_add_pol_expire. In old code (at least back in the 2.6.18 days) err
wasn't used before the return when no policy is found and so the
initialization would cause err to be ENOENT. But since err has since
been used above when we don't get a policy back from the xfrm_policy_by*
function we would always return 0 instead of the intended ENOENT. Also
fixed some white space damage in the same area.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Venkat Yekkirala <vyekkirala@trustedcs.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts an earlier patch which disabled bidirectional mode, meaning that
a listening (passive) socket was not allowed to write to the other (active)
end of the connection.
This mode had been disabled when there were problems with CCID3, but it
imposes a constraint on socket programming and thus hinders deployment.
A change is included to ignore RX feedback received by the TX CCID3 module.
Many thanks to Andre Noll for pointing out this issue.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
physoutdev is only set on purely bridged packet, when nfnetlink_log is used
in the OUTPUT/FORWARD/POSTROUTING hooks on packets forwarded from or to a
bridge it crashes when trying to dereference skb->nf_bridge->physoutdev.
Reported by Holger Eitzenberger <heitzenberger@astaro.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Userspace expects a zero-terminated string, so include the trailing
zero in the netlink message.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The individual fragments of a packet reassembled by conntrack have the
conntrack reference from the reassembled packet attached, but nfctinfo
is not copied. This leaves it initialized to 0, which unfortunately is
the value of IP_CT_ESTABLISHED.
The result is that all IPv6 fragments are tracked as ESTABLISHED,
allowing them to bypass a usual ruleset which accepts ESTABLISHED
packets early.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
sis900 warning fixes
mv643xx_eth: Place explicit port number in mv643xx_eth_platform_data
pcnet32: Fix PCnet32 performance bug on non-coherent architecutres
__devinit & __devexit cleanups for de2104x driver
3c59x: Handle pci_enable_device() failure while resuming
dmfe: Fix link detection
dmfe: fix two bugs
dmfe: trivial/spelling fixes
revert "drivers/net/tulip/dmfe: support basic carrier detection"
ucc_geth: returns NETDEV_TX_BUSY when BD ring is full
ucc_geth: Fix BD processing
natsemi: netpoll fixes
bonding: Improve IGMP join processing
bonding: only receive ARPs for us
bonding: fix double dev_add_pack
This mirrors a recent change in tcp_open_req_child, whereby the icsk_rto of the
newly created child socket was not set (but rather on the parent socket). Same
fix for DCCP.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a bug caused by a previous patch, which causes DCCP servers in
LISTEN state to not receive packets.
This patch changes the logic so that
* servers in either LISTEN or OPEN state get the RX half connection packets
* clients in OPEN state get the TX half connection packets
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a typo in compat_sock_common_getsockopt.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts two changes:
8488df894d248f06726e
A backlog value of N really does mean allow "N + 1" connections
to queue to a listening socket. This allows one to specify
"0" as the backlog and still get 1 connection.
Noticed by Gerrit Renker and Rick Jones.
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a module param "pool_mode" for sunrpc.ko which allows a sysadmin to
choose the mode for mapping NFS thread service pools to CPUs. Values are:
auto choose a mapping mode heuristically
global (default, same as the pre-2.6.19 code) a single global pool
percpu one pool per CPU
pernode one pool per NUMA node
Note that since 2.6.19 the hardcoded behaviour has been "auto", this patch
makes the default "global".
The pool mode can be changed after boot/modprobe using /sys, if the NFS and
lockd services have been shut down. A useful side effect of this change is to
fix a small memory leak when unloading the module.
Signed-off-by: Greg Banks <gnb@melbourne.sgi.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When the last thread of nfsd exits, it shuts down all related sockets. It
currently uses svc_close_socket to do this, but that only is immediately
effective if the socket is not SK_BUSY.
If the socket is busy - i.e. if a request has arrived that has not yet been
processes - svc_close_socket is not effective and the shutdown process spins.
So create a new svc_force_close_socket which removes the SK_BUSY flag is set
and then calls svc_close_socket.
Also change some open-codes loops in svc_destroy to use
list_for_each_entry_safe.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
They don't really save that much, and aren't worth the hassle.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sunrpc server code needs to know the source and destination address for
UDP packets so it can reply properly. It currently copies code out of the
network stack to pick the pieces out of the skb. This is ugly and causes
compile problems with the IPv6 stuff.
So, rip that out and use recv_msg instead. This is a much cleaner interface,
but has a slight cost in that the checksum is now checked before the copy, so
we don't benefit from doing both at the same time. This can probably be
fixed.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In active-backup mode, the current bonding code duplicates IGMP
traffic to all slaves, so that switches are up to date in case of a
failover from an active to a backup interface. If bonding then fails
back to the original active interface, it is likely that the "active
slave" switch's IGMP forwarding for the port will be out of date until
some event occurs to refresh the switch (e.g., a membership query).
This patch alters the behavior of bonding to no longer flood
IGMP to all ports, and to issue IGMP JOINs to the newly active port at
the time of a failover. This insures that switches are kept up to date
for all cases.
"GOELLESCH Niels" <niels.goellesch@eurocontrol.int> originally
reported this problem, and included a patch. His original patch was
modified by Jay Vosburgh to additionally remove the existing IGMP flood
behavior, use RCU, streamline code paths, fix trailing white space, and
adjust for style.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix reference counting (memory leak) problem in __nfulnl_send() and callers
related to packet queueing.
Signed-off-by: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Count module references correctly: after instance_destroy() there
might be timer pending and holding a reference for this netlink instance.
Based on patch by Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate possible NULL pointer dereference in nfulnl_recv_config().
Signed-off-by: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paranoia: instance_put() might have freed the inst pointer when we
spin_unlock_bh().
Signed-off-by: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop reference leaking in nfulnl_log_packet(). If we start a timer we
are already taking another reference.
Signed-off-by: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some stacks apparently send packets with SYN|URG set. Linux accepts
these packets, so TCP conntrack should to.
Pointed out by Martijn Posthuma <posthuma@sangine.com>.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nf_conntrack_netlink config option is named CONFIG_NF_CT_NETLINK,
but multiple files use CONFIG_IP_NF_CONNTRACK_NETLINK or
CONFIG_NF_CONNTRACK_NETLINK for ifdefs.
Fix this and reformat all CONFIG_NF_CT_NETLINK ifdefs to only use a line.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix {nf,ip}_ct_iterate_cleanup unconfirmed list handling:
- unconfirmed entries can not be killed manually, they are removed on
confirmation or final destruction of the conntrack entry, which means
we might iterate forever without making forward progress.
This can happen in combination with the conntrack event cache, which
holds a reference to the conntrack entry, which is only released when
the packet makes it all the way through the stack or a different
packet is handled.
- taking references to an unconfirmed entry and using it outside the
locked section doesn't work, the list entries are not refcounted and
another CPU might already be waiting to destroy the entry
What the code really wants to do is make sure the references of the hash
table to the selected conntrack entries are released, so they will be
destroyed once all references from skbs and the event cache are dropped.
Since unconfirmed entries haven't even entered the hash yet, simply mark
them as dying and skip confirmation based on that.
Reported and tested by Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch splits the vlan_group struct into a multi-allocated struct. On
x86_64, the size of the original struct is a little more than 32KB, causing
a 4-order allocation, which is prune to problems caused by buddy-system
external fragmentation conditions.
I couldn't just use vmalloc() because vfree() cannot be called in the
softirq context of the RCU callback.
Signed-off-by: Dan Aloni <da-x@monatomic.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current CIPSO engine has a problem where it does not verify that
the given sensitivity level has a valid CIPSO mapping when the "std"
CIPSO DOI type is used. The end result is that bad packets are sent
on the wire which should have never been sent in the first place.
This patch corrects this problem by verifying the sensitivity level
mapping similar to what is done with the category mapping. This patch
also changes the returned error code in this case to -EPERM to better
match what the category mapping verification code returns.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This brings things inline with the sk_acceptq_is_full() bug
fix. The limit test should be x >= sk_max_ack_backlog.
Signed-off-by: David S. Miller <davem@davemloft.net>
On 2/28/07, KOVACS Krisztian <hidden@balabit.hu> wrote:
>
> Hi,
>
> While reading TCP minisock code I've found this suspiciously looking
> code fragment:
>
> - 8< -
> struct sock *tcp_create_openreq_child(struct sock *sk, struct request_sock *req, struct sk_buff *skb)
> {
> struct sock *newsk = inet_csk_clone(sk, req, GFP_ATOMIC);
>
> if (newsk != NULL) {
> const struct inet_request_sock *ireq = inet_rsk(req);
> struct tcp_request_sock *treq = tcp_rsk(req);
> struct inet_connection_sock *newicsk = inet_csk(sk);
> struct tcp_sock *newtp;
> - 8< -
>
> The above code initializes newicsk to inet_csk(sk), isn't that supposed
> to be inet_csk(newsk)? As far as I can tell this might leave
> icsk_ack.last_seg_size zero even if we do have received data.
Good catch!
David, please apply the attached patch.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ctnetlink uses netlink_unicast from an atomic_notifier_chain
(which is called within a RCU read side critical section)
without holding further locks. netlink_unicast calls netlink_trim
with the result of gfp_any() for the gfp flags, which are passed
down to pskb_expand_header. gfp_any() only checks for softirq
context and returns GFP_KERNEL, resulting in this warning:
BUG: sleeping function called from invalid context at mm/slab.c:3032
in_atomic():1, irqs_disabled():0
no locks held by rmmod/7010.
Call Trace:
[<ffffffff8109467f>] debug_show_held_locks+0x9/0xb
[<ffffffff8100b0b4>] __might_sleep+0xd9/0xdb
[<ffffffff810b5082>] __kmalloc+0x68/0x110
[<ffffffff811ba8f2>] pskb_expand_head+0x4d/0x13b
[<ffffffff81053147>] netlink_broadcast+0xa5/0x2e0
[<ffffffff881cd1d7>] :nfnetlink:nfnetlink_send+0x83/0x8a
[<ffffffff8834f6a6>] :nf_conntrack_netlink:ctnetlink_conntrack_event+0x94c/0x96a
[<ffffffff810624d6>] notifier_call_chain+0x29/0x3e
[<ffffffff8106251d>] atomic_notifier_call_chain+0x32/0x60
[<ffffffff881d266d>] :nf_conntrack:destroy_conntrack+0xa5/0x1d3
[<ffffffff881d194e>] :nf_conntrack:nf_ct_cleanup+0x8c/0x12c
[<ffffffff881d4614>] :nf_conntrack:kill_l3proto+0x0/0x13
[<ffffffff881d482a>] :nf_conntrack:nf_conntrack_l3proto_unregister+0x90/0x94
[<ffffffff883551b3>] :nf_conntrack_ipv4:nf_conntrack_l3proto_ipv4_fini+0x2b/0x5d
[<ffffffff8109d44f>] sys_delete_module+0x1b5/0x1e6
[<ffffffff8105f245>] trace_hardirqs_on_thunk+0x35/0x37
[<ffffffff8105911e>] system_call+0x7e/0x83
Since netlink_unicast is supposed to be callable from within RCU
read side critical sections, make gfp_any() check for in_atomic()
instead of in_softirq().
Additionally nfnetlink_send needs to use gfp_any() as well for the
call to netlink_broadcast).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change goes with earlier change to get rid of
work queue for path cost. Now stp_set_path_cost does its own
locking. This is to allow it to call br_path_cost() which calls
ethtool interfaces (might sleep).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reading /proc/net/anycast6 when there is no anycast address
on an interface results in an ever-increasing inet6_dev reference
count, as well as a reference to the netdevice you can't get rid of.
Signed-off-by: David S. Miller <davem@davemloft.net>
SPX was removed in early 2.5. How to connect to a Mac or the other OS isn't
hard to find out these days.
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug in Linux IPv6 stack which caused anycast address
to be added to a device prior DAD has been completed. This led to
incorrect reference count which resulted in infinite wait for
unregister_netdevice completion on interface removal.
Signed-off-by: Michal Wrobel <xmxwx@asn.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noted by Kent Yoder, this function will always return an
error. Make sure it returns zero on success.
Signed-off-by: David S. Miller <davem@davemloft.net>
With 2.6.21-rc1, I get an oops when running 'ifdown eth0' and an IPsec
connection is active. If I shut down the connection before running 'ifdown
eth0', then there's no problem. The critical operation of this script is to
kill dhcpd.
The problem is probably caused by commit with git identifier
4337226228 (Linus tree) "[IPSEC]: IPv4 over IPv6
IPsec tunnel".
This patch fixes that oops. I don't know the network code of the Linux
kernel in deep, so if that fix is wrong, please change it. But please
fix the oops. :)
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Please consider applying, this was found on your latest
net-2.6 tree while playing around with that ip_hdr() + turn
skb->nh/h/mac pointers as offsets on 64 bits idea :-)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having a work queue for checking carrier leads to lots of race issues.
Simpler to just get the cost when data structure is created and
update on change.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge hasn't used miscdevice for a long long time.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allocates inetdev at registration for all devices
in line with IPv6. This allows sysctl configuration on the
devices to occur before they're brought up or addresses are
added.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
It is more natural to manage prefix routes corresponding to address which is
being added manually.
With help from Masafumi Aramoto <aramoto@linux-ipv6.org>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Once we reach a point where we exceed the max.path.retrans, strike the
transport before updating the rto. This will force transport switch at
the right time, instead of 1 retransmit too late.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem that this patch corrects happens when all of the following
conditions are satisfisfied:
1. PR-SCTP is used and the timeout on the chunks is set below RTO.Max.
2. One of the paths on a multihomed associations is brought down.
In this scenario, data will expire within the rto of the initial
transmission and will never be retransmitted. However this data still
fills the send buffer and is counted against the association as outstanding
data. This causes any new data not to be sent and retransmission to not
happen.
The fix is to discount the abandoned data from the outstanding count and
peers rwnd estimation. This allows new data to be sent and a retransmission
timer restarted. Even though this new data will most likely expire within
the rto, the timer still counts as a strike against the transport and forces
the FORWARD-TSN chunk to be retransmitted as well.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The locking calls assumed that these code paths were only
invoked in software interrupt context, but that isn't true.
Therefore we need to use spin_{lock,unlock}_bh() throughout.
Signed-off-by: David S. Miller <davem@davemloft.net>
packet_lookup_frame() always returns tpacket_hdr*, so there's no reason
to return char* and require casting by callers.
Also, remove a cast of void*.
Signed-off-by: Jason Lunz <lunz@falooley.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch for adjust inet6_exit() to inverse sequence to inet6_init().
At ipv6_init, it first create proc_root/net/dev_snmp6 entry by call
ipv6_misc_proc_init(), then call addrconf_init() to create the corresponding
device entry at this directory, but at inet6_exit, ipv6_misc_proc_exit()
called first, then call addrconf_init().
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed to set fl_tunnel.fl6_src correctly in xfrm6_bundle_create().
Signed-off-by: Noriaki TAKAMIYA <takamiya@po.ntts.co.jp>
Acked-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds proper prototypes for some functions in
include/net/irda/irda.h
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of bound RFCOMM TTY devices the parent is not available
before its usage. So when opening a RFCOMM TTY device, move it to
the corresponding ACL device as a child. When closing the device,
move it back to the virtual device tree.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The open and close callbacks for the HID device are not optional, but
for the Bluetooth HID report mode support it is enough to add empty
dummy callbacks.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch extends the current Bluetooth HID support to use the new
HID subsystem and adds full report mode support.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The compat ioctl patch copied the parser version field into the
report descriptor size field by mistake.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We frequently need the maximum number of possible processors in order to
allocate arrays for all processors. So far this was done using
highest_possible_processor_id(). However, we do need the number of
processors not the highest id. Moreover the number was so far dynamically
calculated on each invokation. The number of possible processors does not
change when the system is running. We can therefore calculate that number
once.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
highest_possible_node_id() is currently used to calculate the last possible
node idso that the network subsystem can figure out how to size per node
arrays.
I think having the ability to determine the maximum amount of nodes in a
system at runtime is useful but then we should name this entry
correspondingly, it should return the number of node_ids, and the the value
needs to be setup only once on bootup. The node_possible_map does not
change after bootup.
This patch introduces nr_node_ids and replaces the use of
highest_possible_node_id(). nr_node_ids is calculated on bootup when the
page allocators pagesets are initialized.
[deweerdt@free.fr: fix oops]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (25 commits)
Documentation/kernel-docs.txt update.
arch/cris: typo in KERN_INFO
Storage class should be before const qualifier
kernel/printk.c: comment fix
update I/O sched Kconfig help texts - CFQ is now default, not AS.
Remove duplicate listing of Cris arch from README
kbuild: more doc. cleanups
doc: make doc. for maxcpus= more visible
drivers/net/eexpress.c: remove duplicate comment
add a help text for BLK_DEV_GENERIC
correct a dead URL in the IP_MULTICAST help text
fix the BAYCOM_SER_HDX help text
fix SCSI_SCAN_ASYNC help text
trivial documentation patch for platform.txt
Fix typos concerning hierarchy
Fix comment typo "spin_lock_irqrestore".
Fix misspellings of "agressive".
drivers/scsi/a100u2w.c: trivial typo patch
Correct trivial typo in log2.h.
Remove useless FIND_FIRST_BIT() macro from cardbus.c.
...
Provide an audit record of the descriptor pair returned by pipe() and
socketpair(). Rewritten from the original posted to linux-audit by
John D. Ramsdell <ramsdell@mitre.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Correct mis-spellings of "algorithm", "appear", "consistent" and
(shame, shame) "kernel".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
There is a bug in ieee80211softmac that always sets the user rate
to 11Mbs, no matter the capabilities of the device. This bug was
probably beneficial as long as the bcm43xx cards were rate limited;
however, most are now capable of relatively high speeds. This patch
fixes that bug and eliminates an assert that is no longer needed.
Once the cards are capable of full OFDM speeds, the 24 Mbs rate will
be changed to 54 Mbs.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It isn't needed anymore, all of the users are gone, and all of the ctl_table
initializers have been converted to use explicit names of the fields they are
initializing.
[akpm@osdl.org: NTFS fix]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The semantic effect of insert_at_head is that it would allow new registered
sysctl entries to override existing sysctl entries of the same name. Which is
pain for caching and the proc interface never implemented.
I have done an audit and discovered that none of the current users of
register_sysctl care as (excpet for directories) they do not register
duplicate sysctl entries.
So this patch simply removes the support for overriding existing entries in
the sys_sysctl interface since no one uses it or cares and it makes future
enhancments harder.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Corey Minyard <minyard@acm.org>
Cc: Neil Brown <neilb@suse.de>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jan Kara <jack@ucw.cz>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: David Chinner <dgc@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Arnaldo Carvalho de Melo <acme@conectiva.com.br>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Arnaldo Carvalho de Melo <acme@conectiva.com.br>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sysctl numbers used are unique so setting the insert_at_head flag does not
succeed in overriding any sysctls, and is just confusing because it doesn't.
Clear the flag.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Patrick Caulfield <patrick@tykepenguin.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sysctl numbers used are unique so setting the insert_at_head flag servers
no semantic purpose and is just confusing.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Arnaldo Carvalho de Melo <acme@conectiva.com.br>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sysctl numbers used are unique so setting the insert_at_head flag serves
no semantis purpose, and is just confusing.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Arnaldo Carvalho de Melo <acme@conectiva.com.br>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sysctl numbers used are unique so setting the insert_at_head flag serves
no semantic purpose, so it is just confusing.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sysctl numbers used are unique so setting the insert_at_head flag serves
no semantic purpose.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We don't need this to prevent module unload races so remove the unnecessary
code.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Because the sunrpc sysctls don't conflict with any other sysctls the setting
the insert at head flag to register_sysctl has no semantic meaning.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There has not been much maintenance on sysctl in years, and as a result is
there is a lot to do to allow future interesting work to happen, and being
ambitious I'm trying to do it all at once :)
The patches in this series fall into several general categories.
- Removal of useless attempts to override the standard sysctls
- Registers of sysctl numbers in sysctl.h so someone else does not use
the magic number and conflict.
- C99 conversions so it becomes possible to change the layout of
struct ctl_table without breaking everything.
- Removal of useless claims of module ownership, in the proc dir entries
- Removal of sys_sysctl support where people had used conflicting sysctl
numbers. Trying to break glibc or other applications by changing the
ABI is not cool. 9 instances of this in the kernel seems a little
extreme.
- General enhancements when I got the junk I could see out.
This patch:
Since x25 uses unique binary numbers inserting yourself at the head of the
search list for sysctls so you can override already registered sysctls is
pointless.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
AUTH_UNIX authentication (the standard with NFS) has a limit of 16 groups ids.
This causes problems for people in more than 16 groups.
So allow the server to map a uid into a list of group ids based on local
knowledge rather depending on the (possibly truncated) list from the client.
If there is no process on the server responding to upcalls, the gidlist in the
request will still be used.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the address family to refer encap_family
when comparing with a kernel generated xfrm_state
Signed-off-by: Kazunori MIYAZAWA <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes xfrm6_tunnel register and deregister
interface to prepare for solving the conflict of device
tunnels with inter address family IPsec tunnel.
There is no device which conflicts with IPv4 over IPv6
IPsec tunnel.
Signed-off-by: Kazunori MIYAZAWA <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes sit use xfrm4_tunnel_register instead of
inet_add_protocol. It solves conflict of sit device with
inter address family IPsec tunnel.
Signed-off-by: Kazunori MIYAZAWA <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes xfrm4_tunnel register and deregister
interface to prepare for solving the conflict of device
tunnels with inter address family IPsec tunnel.
Signed-off-by: Kazunori MIYAZAWA <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP may advertize up to 16-bits window in SYN packets (no window
scaling allowed). At the same time, TCP may have rcv_wnd
(32-bits) that does not fit to 16-bits without window scaling
resulting in pseudo garbage into advertized window from the
low-order bits of rcv_wnd. This can happen at least when
mss <= (1<<wscale) (see tcp_select_initial_window). This patch
fixes the handling of SYN advertized windows (compile tested
only).
In worst case (which is unlikely to occur though), the receiver
advertized window could be just couple of bytes. I'm not sure
that such situation would be handled very well at all by the
receiver!? Fortunately, the situation normalizes after the
first non-SYN ACK is received because it has the correct,
scaled window.
Alternatively, tcp_select_initial_window could be changed to
prevent too large rcv_wnd in the first place.
[ tcp_make_synack() has the same bug, and I've added a fix for
that to this patch -DaveM ]
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jarek Poplawski <jarkao2@o2.pl>
Acked-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TCP reset packet is copied from the original. This
includes all the GSO bits which do not apply to the new
packet. So we should clear those bits.
Spotted by Patrick McHardy.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC3530 section 3.1.1 states an NFSv4 client MUST NOT send a request
twice on the same connection unless it is the NULL procedure. Section
3.1.1 suggests that the client should disconnect and reconnect if it
wants to retry a request.
Implement this by adding an rpc_clnt flag that an ULP can use to
specify that the underlying transport should be disconnected on a
major timeout. The NFSv4 client asserts this new flag, and requests
no retries after a minor retransmit timeout.
Note that disconnecting on a retransmit is in general not safe to do
if the RPC client does not reuse the TCP port number when reconnecting.
See http://bugzilla.linux-nfs.org/show_bug.cgi?id=6
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Tetsuo Handa <handat@pm.nttdata.co.jp> told me that connect(2) with TCPv6
socket almost always took a few minutes to return when we did not have any
ports available in the range of net.ipv4.ip_local_port_range.
The reason was that we used incorrect seed for calculating index of
hash when we check established sockets in __inet6_check_established().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure that this function is called correctly, and
add BUG() checking to ensure the arguments are sane.
Based upon a patch by Joy Latten.
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor non-invasive cleanups:
* white space around operators and line wrapping
* use const
* use __read_mostly
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
These module parameters should be in the read mostly area to avoid
cache pollution.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
sysctls are registered by the protocol module itself since 2.6.19, no need
to have them visible to others.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Regarding RFC3775, MH payload proto field should be IPPROTO_NONE. Otherwise
it must be discarded (and the receiver should send ICMP error).
We assume filter should drop such piggyback everytime to disallow slipping
through firewall rules, even the final receiver will discard it.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of depending on internally needed options and letting users
figure out what is needed, select them when needed:
- IP_NF_IPTABLES, IP_NF_ARPTABLES and IP6_NF_IPTABLES select
NETFILTER_XTABLES
- NETFILTER_XT_TARGET_CONNMARK, NETFILTER_XT_MATCH_CONNMARK and
IP_NF_TARGET_CLUSTERIP select NF_CONNTRACK_MARK
- NETFILTER_XT_MATCH_CONNBYTES selects NF_CT_ACCT
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use NF_IP6_ instead of NF_IP_. The values are identical, this is merely
cleanup.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
No caller checks the return value, and since its usually called within the
module unload path there's nothing a module could do about errors anyway,
so BUG on invalid conditions and return void.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
NF_CT_STAT_INC assumes rcu_read_lock in nf_hook_slow disables
preemption as well, making it legal to use __get_cpu_var without
disabling preemption manually. The assumption is not correct anymore
with preemptable RCU, additionally we need to protect against softirqs
when not holding nf_conntrack_lock.
Add NF_CT_STAT_INC_ATOMIC macro, which disables local softirqs,
and use where necessary.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONNTRACK_STAT_INC assumes rcu_read_lock in nf_hook_slow disables
preemption as well, making it legal to use __get_cpu_var without
disabling preemption manually. The assumption is not correct anymore
with preemptable RCU, additionally we need to protect against softirqs
when not holding ip_conntrack_lock.
Add CONNTRACK_STAT_INC_ATOMIC macro, which disables local softirqs,
and use where necessary.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace preempt_{enable,disable} based RCU by proper use of the
RCU API and add missing rcu_read_lock/rcu_read_unlock calls in
all paths not obviously only used within packet process context
(nfnetlink_conntrack).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace preempt_{enable,disable} based RCU by proper use of the
RCU API and add missing rcu_read_lock/rcu_read_unlock calls in
all paths not obviously only used within packet process context
(nfnetlink_conntrack).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace preempt_{enable,disable} based RCU by proper use of the
RCU API and add missing rcu_read_lock/rcu_read_unlock calls in
paths used outside of packet processing context (nfnetlink_conntrack).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace preempt_{enable,disable} based RCU by proper use of the
RCU API and add missing rcu_read_lock/rcu_read_unlock calls in
paths used outside of packet processing context (nfnetlink_conntrack).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
- rename nf_logging to nf_loggers since its an array of registered loggers
- rename nf_log_unregister_logger() to nf_log_unregister() to make it
symetrical to nf_log_register() and convert all users
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The spinlock is only used in process context (register/unregister),
switch to a mutex.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the only user of nf_log_unregister_pf (nfnetlink_log) doesn't
check the return value, change it to void and bail out silently when
a non-existant address family is supplied.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also replace synchronize_net() calls by synchronize_rcu() since the
RCU protected data is also used for sysfs.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The spinlock is only used in process context (register/unregister)
since RCU is used for the nf_hook lists, switch to a mutex.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The spinlock is only used in process context (register/unregister),
switch to a mutex.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're only adding to the list, no need to synchronize.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use rcu_assign_pointer/rcu_dereference for ip_ct_attach pointer instead
of self-made RCU and use rcu_read_lock to make sure the conntrack module
doesn't disappear below us while calling it, since this function can be
called from outside the netfilter hooks.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace existing svc_create_socket() API to allow callers to pass addresses
larger than a sockaddr_in.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: Aurelien Charbon <aurelien.charbon@ext.bull.net>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for IPv6 addresses in the RPC server's UDP receive path.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: Aurelien Charbon <aurelien.charbon@ext.bull.net>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Modify svc_tcp_accept to support connecting on IPv6 sockets.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: Aurelien Charbon <aurelien.charbon@ext.bull.net>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The only reason svcsock.c looks at a sockaddr's port is to check whether the
remote peer is connecting from a privileged port. Refactor this check to hide
processing that is specific to address format.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: Aurelien Charbon <aurelien.charbon@ext.bull.net>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CMSG_DATA comes in different sizes, depending on address family.
[akpm@linux-foundation.org: remove unneeded do/while (0)]
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: Aurelien Charbon <aurelien.charbon@ext.bull.net>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ilpo Järvinen
Patrick McHardy