It should be the dst in the copy not src. 03a001948 introduced this bug.
Reported-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The get operation was not sending the message that was built to
user-space. This patch also includes the appropriate handling for
the return value of netlink_unicast().
Moreover, fix error codes on error (for example, for non-existing
entry was uncorrect).
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The sanity check (timeout < 0) never works; the dividend is unsigned
and so is the division, which should have been a signed division.
long timeout = (ct->timeout.expires - jiffies) / HZ;
if (timeout < 0)
timeout = 0;
This patch converts the time values to signed for the division.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We should not forget to try for real server with port 0
in the backup server when processing the sync message. We should
do it in all cases because the backup server can use different
forwarding method.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Commit 10f6dfcfde (Revert "sch_netem: Remove classful functionality")
reintroduced classful functionality to netem, but broke basic netem
behavior :
netem uses an t(ime)fifo queue, and store timestamps in skb->cb[]
If qdisc is changed, time constraints are not respected and other qdisc
can destroy skb->cb[] and block netem at dequeue time.
Fix this by always using internal tfifo, and optionally attach a child
qdisc to netem (or a tree of qdiscs)
Example of use :
DEV=eth3
tc qdisc del dev $DEV root
tc qdisc add dev $DEV root handle 30: est 1sec 8sec netem delay 20ms 10ms
tc qdisc add dev $DEV handle 40:0 parent 30:0 tbf \
burst 20480 limit 20480 mtu 1514 rate 32000bps
qdisc netem 30: root refcnt 18 limit 1000 delay 20.0ms 10.0ms
Sent 190792 bytes 413 pkt (dropped 0, overlimits 0 requeues 0)
rate 18416bit 3pps backlog 0b 0p requeues 0
qdisc tbf 40: parent 30: rate 256000bit burst 20Kb/8 mpu 0b lat 0us
Sent 190792 bytes 413 pkt (dropped 6, overlimits 10 requeues 0)
backlog 0b 5p requeues 0
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During some debugging I needed to look into how /proc/net/ipv6_route
operated and in my digging I found its calling fib6_clean_all() which uses
"write_lock_bh(&table->tb6_lock)" before doing the walk of the table. I
found this on 2.6.32, but reading the code I believe the same basic idea
exists currently. Looking at the rtnetlink code they are only calling
"read_lock_bh(&table->tb6_lock);" via fib6_dump_table(). While I realize
reading from proc isn't the recommended way of fetching the ipv6 route
table; taking a write lock seems unnecessary and would probably cause
network performance issues.
To verify this I loaded up the ipv6 route table and then ran iperf in 3
cases:
* doing nothing
* reading ipv6 route table via proc
(while :; do cat /proc/net/ipv6_route > /dev/null; done)
* reading ipv6 route table via rtnetlink
(while :; do ip -6 route show table all > /dev/null; done)
* Load the ipv6 route table up with:
* for ((i = 0;i < 4000;i++)); do ip route add unreachable 2000::$i; done
* iperf commands:
* client: iperf -i 1 -V -c <ipv6 addr>
* server: iperf -V -s
* iperf results - 3 runs each (in Mbits/sec)
* nothing: client: 927,927,927 server: 927,927,927
* proc: client: 179,97,96,113 server: 142,112,133
* iproute: client: 928,927,928 server: 927,927,927
lock_stat shows taking the write lock is causing the slowdown. Using this
info I decided to write a version of fib6_clean_all() which replaces
write_lock_bh(&table->tb6_lock) with read_lock_bh(&table->tb6_lock). With
this new function I see the same results as with my rtnetlink iperf test.
Signed-off-by: Josh Hunt <joshhunt00@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While it's not too late fix the recently added RQLEN diag extension
to report rqlen and wqlen in the same way as TCP does.
I.e. for listening sockets the ack backlog length (which is the input
queue length for socket) in rqlen and the max ack backlog length in
wqlen, and what the CINQ/OUTQ ioctls do for established.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently tcp diag reports rqlen and wqlen values similar to how
the CINQ/COUTQ iotcls do. To make unix diag report these values
in the same way move the respective code into helpers.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ Fix indentation of sock_diag*() calls. -DaveM ]
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a routine that dumps memory-related values of a socket.
It's made as an array to make it possible to add more stuff
here later without breaking compatibility.
Since v1: The SK_MEMINFO_ constants are in userspace
visible part of sock_diag.h, the rest is under __KERNEL__.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The addition of the "s" to indicate pluralization is intentional,
since the struct actually contains two name variants.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This changes both the struct bcbearer and struct bcbearer_pair to
have the "tipc_" prefix. Runtime behaviour is unchanged.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Make this rename so that it is consistent with the majority
of the other tipc structs and to assist in removing any
ambiguity with other similar names in other subsystems.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Make this rename so that it is consistent with the majority
of the other tipc structs and to assist in removing any
ambiguity with other similar names in other subsystems.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Make this rename so that it is consistent with the majority
of the other tipc structs and to assist in removing any
ambiguity with other similar names in other subsystems.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Make this rename so that it is consistent with the majority
of the other tipc structs and to assist in removing any
ambiguity with other similar names in other subsystems.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Give it a meaningful prefix, as suggested by DaveM, so that it
is consistent with things like struct tipc_bearer, and so it isn't
confused with anything else. This has no impact on the actual
runtime code behaviour.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
In some of the rt6_bind_neighbour() call sites, it hasn't hooked
up the rt->dst.dev pointer yet, so we'd deref a NULL pointer when
obtaining dev->ifindex for the neighbour hash function computation.
Just pass the netdevice explicitly in to fix this problem.
Reported-by: Bjarke Istrup Pedersen <gurligebis@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
warning: (NETFILTER_XT_MATCH_NFACCT) selects NETFILTER_NETLINK_ACCT which has
unmet direct dependencies (NET && INET && NETFILTER && NETFILTER_ADVANCED)
and then
ERROR: "nfnetlink_subsys_unregister" [net/netfilter/nfnetlink_acct.ko] undefined!
ERROR: "nfnetlink_subsys_register" [net/netfilter/nfnetlink_acct.ko] undefined!
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
It just obscures that the netdevice pointer and the expires value are
implemented in the dst_entry sub-object of the ipv6 route.
And it makes grepping for dst_entry member uses much harder too.
Signed-off-by: David S. Miller <davem@davemloft.net>
Also, create and use an rt6_bind_neighbour() in net/ipv6/route.c to
consolidate some common logic.
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to perform a proper universal hash on a vector of integers,
we have to use different universal hashes on each vector element.
Which means we need 4 different hash randoms for ipv6.
Signed-off-by: David S. Miller <davem@davemloft.net>
Check setsockopt arguments to avoid overflows and return -EINVAL for
too large arguments.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit be639ac6 ("NET: AX.25: Check ioctl arguments to avoid overflows
further down the road") rejects very large arguments, but doesn't
completely fix overflows on 64-bit systems. Consider the AX25_T2 case.
int opt;
...
if (opt < 1 || opt > ULONG_MAX / HZ) {
res = -EINVAL;
break;
}
ax25->t2 = opt * HZ;
The 32-bit multiplication opt * HZ would overflow before being assigned
to 64-bit ax25->t2. This patch changes "opt" to unsigned long.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When testing L2TP support, I discovered that the l2tp module is not autoloaded
as are other netlink interfaces. There is because of lack of hook in genetlink to call
request_module and load the module.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The route we have here is for the address being added to the interface,
ie. for input packet processing.
Therefore using that route to determine whether an output nexthop gateway
is known and resolved doesn't make any sense.
So, simply remove this test, it never triggered anyways.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-By: Neil Horman <nhorman@tuxdriver.com>
If bind is fail when bind is called after set PACKET_FANOUT
sock option, the dev refcnt will leak.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using /proc/net/nf_conntrack has been deprecated in favour of the
conntrack(8) tool.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
References: http://www.spinics.net/lists/netfilter-devel/msg18875.html
Augment xt_ecn by facilities to match on IPv6 packets' DSCP/TOS field
similar to how it is already done for the IPv4 packet field.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use the new macro and struct names in xt_ecn.h, and put the old
definitions into a definition-forwarding ipt_ecn.h.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Prepare the ECN match for augmentation by an IPv6 counterpart. Since
no symbol dependencies to ipv6.ko are added, having a single ecn match
module is the more so welcome.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Migrates the buf_seqno() helper routine from broadcast link level to
unicast link level so that it can be used both types of TIPC links.
This is a cosmetic change only, and does not affect the operation of TIPC.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Adds checks to TIPC's broadcast link so that it ignores any
acknowledgement message containing a sequence number that does not
correspond to an unacknowledged message currently in the broadcast
link's transmit queue.
This change prevents the broadcast link from becoming stalled if a
newly booted node receives stale broadcast link acknowledgement
information from another node that has not yet fully synchronized
its end of the broadcast link to reflect the current state of the
new node's end.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Adds code to release any unsent broadcast messages in the broadcast link
transmit queue if TIPC loses contact with its only neighboring node.
Previously, a broadcast link that was in the congested state would hold
on to the unsent messages, even though the messages were now undeliverable.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The two broadcast link statistics fields that are used to derive the
average length of that link's transmit queue are now updated only after
a successful attempt to send a broadcast message, since there is no need
to update these values when an unsuccessful send attempt leaves the
queue unchanged.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Adds a check to detect when an attempt is made to send a message
via the broadcast link and no neighboring nodes are currently available
to receive it. Rather than wasting effort passing the message to the
broadcast link and broadcast bearer, who will only throw it away,
TIPC now frees the message immediately and reports success (i.e. the
message has been delivered to all available destinations).
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Fixes oversight that allowed broadcast link node map to be updated without
first taking the broadcast link spinlock that protects the map. As part
of this fix the node map has been incorporated into the broadcast link
structure to make the need for such protection more evident.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Creates global variables to hold the broadcast link's pseudo-bearer and
pseudo-link structures, rather than allocating them dynamically. There
is only a single instance of each structure, and changing over to static
allocation allows elimination of code to handle the cases where dynamic
allocation was unsuccessful.
The memset in the teardown code may look like they aren't used, but
the same teardown code is run when there is a non-fatal error at
init-time, so that stale data isn't present when the user fixes the
cause of the soft error.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Gets rid of an unnecessary check in the routine that updates the port id
of a node's name publications when the node is assigned a network address,
since the routine is only invoked if the new address is different from
the existing one.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies TIPC's module unloading logic to switch itself into "single
node" mode before starting to terminate networking support. This helps
to ensure that no operations that require TIPC to be in "networking"
mode can initiate once unloading starts.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Gets rid of two pointless operations that zero out the array used to
record information about TIPC's Ethernet bearers. There is no need to
initialize the array on start up since it is a global variable that is
already zero'd out, and there is no need to zero it out on exit because
the array is never referenced again.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies Ethernet bearer disable logic to break the association between
the bearer and its device driver at the time the bearer is disabled,
rather than when the TIPC module is unloaded. This allows the array
entry used by the disabled bearer to be re-used if the same bearer (or
a different one) is subsequently enabled.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Change TIPC's shutdown code to deactivate generic networking support
before terminating Ethernet media support. The deactivation of generic
networking support causes all existing bearers to be destroyed, meaning
the Ethernet media termination routine no longer has to bother marking
them as unavailable.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Comment-only change to better explain why TIPC's configuration lock is
temporarily released while activating support for network interfaces,
and why the existing activation code doesn't require rework.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Permits run-time alteration of default link settings on a per-media
and per-bearer basis, in addition to the existing per-link basis.
The following syntax can now be used:
tipc-config -lt=<link-name|bearer-name|media-name>/<tolerance>
tipc-config -lp=<link-name|bearer-name|media-name>/<priority>
tipc-config -lw=<link-name|bearer-name|media-name>/<window>
Note that changes to the default settings for a given media type has
no effect on the default settings used by existing bearers. Similarly,
changes to default bearer settings has no effect on existing link
endpoints that utilize that interface.
Thanks to Florian Westphal <fw@strlen.de> for his contributions to
the development of this enhancement.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Adds a check to ensure that TIPC ignores an incoming neighbor discovery
message that specifies an invalid media address as its source. The check
ensures that the source address is a valid, non-broadcast address that
could legally be used by a neighboring link endpoint.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reworks TIPC's media address data structure and associated processing
routines to transfer all media-specific details of address conversion
to the associated TIPC media adaptation code. TIPC's generic bearer code
now only needs to know which media type an address is associated with
and whether or not it is a broadcast address, and totally ignores the
"value" field that contains the actual media-specific addressing info.
These changes eliminate the need for a number of endianness conversion
operations and will make it easier for TIPC to support new media types
in the future.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Enhances TIPC's Ethernet media support to provide 3 new address conversion
routines, which allow TIPC to interpret an address that is in string form
and to convert an address to and from the 20 byte format used in TIPC's
neighbor discovery messages.
These routines are pre-requisites to a follow on commit that hides all
media-specific addressing details from TIPC's generic bearer code.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Enhances conversion of a media address to printable form so that an
unconvertable address will be displayed as a string of hex digits,
rather than not being displayed at all. (Also removes a pointless check
for the existence of the media-specific address conversion routine,
since the routine is not optional.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Simplifies error handling performed during media registration, since
TIPC no longer supports the dynamic addition of new media types that
are potentially error-prone. These simplifications include the following:
1) No longer check for premature registration of a new media type.
2) No longer check for negative link priority values (which was pointless
since such values are unsigned, and could cause a compiler warning).
3) No longer generate a warning describing the exact cause of any
registration failure (just warns that overall registration failed).
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Changes TIPC's list of registered media types from an array of media
structures to an array of pointers to media structures. This eliminates
the need to copy of the contents of the structure passed in during media
registration.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Streamlines the detection of an attempt to register a TIPC media structure
using an already registered name or type identifier. The revised logic now
reuses an existing routine to detect an existing name and no longer
unnecessarily manipulates the media type counter during an unsuccessful
registration attempt.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Speeds up the registration of TIPC media types by passing in a structure
containing the required information, rather than by passing in the various
fields describing the media type individually.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Permits a Linux container to use TIPC sockets even when it has its own
network namespace defined by removing the check that prohibits such use.
This makes it possible for users who wish to isolate their container
network traffic from normal network traffic to utilize TIPC.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
RDBG() wasn't even used, and the messages printed by RT6_DEBUG() were
far from useful. Just get rid of all this stuff, we can replace it
with something more suitable if we want.
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise we leave uninitialized kernel memory in there.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NLA_PUT macro should accept the actual attribute length, not
the amount of elements in array :(
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* pm-sleep: (51 commits)
PM: Drop generic_subsys_pm_ops
PM / Sleep: Remove forward-only callbacks from AMBA bus type
PM / Sleep: Remove forward-only callbacks from platform bus type
PM: Run the driver callback directly if the subsystem one is not there
PM / Sleep: Make pm_op() and pm_noirq_op() return callback pointers
PM / Sleep: Merge internal functions in generic_ops.c
PM / Sleep: Simplify generic system suspend callbacks
PM / Hibernate: Remove deprecated hibernation snapshot ioctls
PM / Sleep: Fix freezer failures due to racy usermodehelper_is_disabled()
PM / Sleep: Recommend [un]lock_system_sleep() over using pm_mutex directly
PM / Sleep: Replace mutex_[un]lock(&pm_mutex) with [un]lock_system_sleep()
PM / Sleep: Make [un]lock_system_sleep() generic
PM / Sleep: Use the freezer_count() functions in [un]lock_system_sleep() APIs
PM / Freezer: Remove the "userspace only" constraint from freezer[_do_not]_count()
PM / Hibernate: Replace unintuitive 'if' condition in kernel/power/user.c with 'else'
Freezer / sunrpc / NFS: don't allow TASK_KILLABLE sleeps to block the freezer
PM / Sleep: Unify diagnostic messages from device suspend/resume
ACPI / PM: Do not save/restore NVS on Asus K54C/K54HR
PM / Hibernate: Remove deprecated hibernation test modes
PM / Hibernate: Thaw processes in SNAPSHOT_CREATE_IMAGE ioctl test path
...
Conflicts:
kernel/kmod.c
We currently have two ways to account traffic in netfilter:
- iptables chain and rule counters:
# iptables -L -n -v
Chain INPUT (policy DROP 3 packets, 867 bytes)
pkts bytes target prot opt in out source destination
8 1104 ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0
- use flow-based accounting provided by ctnetlink:
# conntrack -L
tcp 6 431999 ESTABLISHED src=192.168.1.130 dst=212.106.219.168 sport=58152 dport=80 packets=47 bytes=7654 src=212.106.219.168 dst=192.168.1.130 sport=80 dport=58152 packets=49 bytes=66340 [ASSURED] mark=0 use=1
While trying to display real-time accounting statistics, we require
to pool the kernel periodically to obtain this information. This is
OK if the number of flows is relatively low. However, in case that
the number of flows is huge, we can spend a considerable amount of
cycles to iterate over the list of flows that have been obtained.
Moreover, if we want to obtain the sum of the flow accounting results
that match some criteria, we have to iterate over the whole list of
existing flows, look for matchings and update the counters.
This patch adds the extended accounting infrastructure for
nfnetlink which aims to allow displaying real-time traffic accounting
without the need of complicated and resource-consuming implementation
in user-space. Basically, this new infrastructure allows you to create
accounting objects. One accounting object is composed of packet and
byte counters.
In order to manipulate create accounting objects, you require the
new libnetfilter_acct library. It contains several examples of use:
libnetfilter_acct/examples# ./nfacct-add http-traffic
libnetfilter_acct/examples# ./nfacct-get
http-traffic = { pkts = 000000000000, bytes = 000000000000 };
Then, you can use one of this accounting objects in several iptables
rules using the new nfacct match (which comes in a follow-up patch):
# iptables -I INPUT -p tcp --sport 80 -m nfacct --nfacct-name http-traffic
# iptables -I OUTPUT -p tcp --dport 80 -m nfacct --nfacct-name http-traffic
The idea is simple: if one packet matches the rule, the nfacct match
updates the counters.
Thanks to Patrick McHardy, Eric Dumazet, Changli Gao for reviewing and
providing feedback for this contribution.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Aim of this patch is to provide full range of rps_flow_cnt on 64bit arches.
Theorical limit on number of flows is 2^32
Fix some buggy RPS/RFS macros as well.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Tom Herbert <therbert@google.com>
CC: Xi Wang <xi.wang@gmail.com>
CC: Laurent Chavey <chavey@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 6373a9a286 (netem: use vmalloc for distribution table) added a
regression, since vfree() is called while holding a spinlock and BH
being disabled.
Fix this by doing the pointers swap in critical section, and freeing
after spinlock release.
Also add __GFP_NOWARN to the kmalloc() try, since we fallback to
vmalloc().
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes one scheduling while atomic error:
[ 385.565186] ctnetlink v0.93: registering with nfnetlink.
[ 385.565349] BUG: scheduling while atomic: lt-expect_creat/16163/0x00000200
It can be triggered with utils/expect_create included in
libnetfilter_conntrack if the FTP helper is not loaded.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This fixes one bogus error that is returned to user-space:
libnetfilter_conntrack/utils# ./expect_get
TEST: get expectation (-1)(Unknown error 18446744073709551504)
This patch includes the correct handling for EAGAIN (nfnetlink
uses this error value to restart the operation after module
auto-loading).
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The get and zero operations have to be done in an atomic context,
otherwise counters added between them will be lost.
This problem was spotted by Changli Gao while discussing the
nfacct infrastructure.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We can't do this without propagating the const to nlk_sk()
too, otherwise:
net/netlink/af_netlink.c: In function ‘netlink_is_kernel’:
net/netlink/af_netlink.c:103:2: warning: passing argument 1 of ‘nlk_sk’ discards ‘const’ qualifier from pointer target type [enabled by default]
net/netlink/af_netlink.c:96:36: note: expected ‘struct sock *’ but argument is of type ‘const struct sock *’
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/bluetooth/l2cap_core.c
Just two overlapping changes, one added an initialization of
a local variable, and another change added a new local variable.
Signed-off-by: David S. Miller <davem@davemloft.net>
The new netem loss model is configured with nested netlink messages.
This code is being overly strict about sizes, and is easily confused
by padding (or possible future expansion). Also message
for gemodel is incorrect.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add backlog (byte count) information in hfsc classes and qdisc, so that
"tc -s" can report it to user, instead of 0 values :
qdisc hfsc 1: root refcnt 6 default 20
Sent 45141660 bytes 30545 pkt (dropped 0, overlimits 91751 requeues 0)
rate 1492Kbit 126pps backlog 103226b 74p requeues 0
...
class hfsc 1:20 parent 1:1 leaf 1201: rt m1 0bit d 0us m2 400000bit ls m1 0bit d 0us m2 200000bit
Sent 49534912 bytes 33519 pkt (dropped 0, overlimits 0 requeues 0)
backlog 81822b 56p requeues 0
period 23 work 49451576 bytes rtwork 13277552 bytes level 0
...
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: John A. Sullivan III <jsullivan@opensourcedevel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit e1b6eb3ccb.
This was causing a delay of 10 seconds in the resume process of a Thinkpad
laptop. I'm afraid this could affect more devices once 3.2 is released.
Reported-by: Tomáš Janoušek <tomi@nomi.cz>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch fixes incorrect address storage while storing
Long Term Key for LE Devices using SMP (Security Manager Protocol).
The address stored should be of remote device and not of source device.
Signed-off-by: Hemant Gupta <hemant.gupta@stericsson.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
"! --connbytes 23:42" should match if the packet/byte count is not in range.
As there is no explict "invert match" toggle in the match structure,
userspace swaps the from and to arguments
(i.e., as if "--connbytes 42:23" were given).
However, "what <= 23 && what >= 42" will always be false.
Change things so we use "||" in case "from" is larger than "to".
This change may look like it breaks backwards compatibility when "to" is 0.
However, older iptables binaries will refuse "connbytes 42:0",
and current releases treat it to mean "! --connbytes 0:42",
so we should be fine.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The NAT range to nlattr conversation callbacks and helpers are entirely
dead code and are also useless since there are no NAT ranges in conntrack
context, they are only used for initially selecting a tuple. The final NAT
information is contained in the selected tuples of the conntrack entry.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The packet size check originates from a time when UDP helpers could
accidentally mangle incorrect packets (NEWNAT) and is unnecessary
nowadays since the conntrack helpers invoke the NAT helpers for the
proper packet directly.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The inner tuple that is extracted from the packet is unused. The code also
doesn't have any useful side-effects like verifying the packet does contain
enough data to extract the inner tuple since conntrack already does the
same, so remove it.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The only remaining user of NAT protocol module reference counting is NAT
ctnetlink support. Since this is a fairly short sequence of code, convert
over to use RCU and remove module reference counting.
Module unregistration is already protected by RCU using synchronize_rcu(),
so no further changes are necessary.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use nf_conntrack_hash_rnd in NAT bysource hash to avoid hash chain attacks.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Export the NAT definitions to userspace. So far userspace (specifically,
iptables) has been copying the headers files from include/net. Also
rename some structures and definitions in preparation for IPv6 NAT.
Since these have never been officially exported, this doesn't affect
existing userspace code.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This partially reworks bc01befdcf
which added userspace expectation support.
This patch removes the nf_ct_userspace_expect_list since now we
force to use the new iptables CT target feature to add the helper
extension for conntracks that have attached expectations from
userspace.
A new version of the proof-of-concept code to implement userspace
helpers from userspace is available at:
http://people.netfilter.org/pablo/userspace-conntrack-helpers/nf-ftp-helper-POC.tar.bz2
This patch also modifies the CT target to allow to set the
conntrack's userspace helper status flags. This flag is used
to tell the conntrack system to explicitly allocate the helper
extension.
This helper extension is useful to link the userspace expectations
with the master conntrack that is being tracked from one userspace
helper.
This feature fixes a problem in the current approach of the
userspace helper support. Basically, if the master conntrack that
has got a userspace expectation vanishes, the expectations point to
one invalid memory address. Thus, triggering an oops in the
expectation deletion event path.
I decided not to add a new revision of the CT target because
I only needed to add a new flag for it. I'll document in this
issue in the iptables manpage. I have also changed the return
value from EINVAL to EOPNOTSUPP if one flag not supported is
specified. Thus, in the future adding new features that only
require a new flag can be added without a new revision.
There is no official code using this in userspace (apart from
the proof-of-concept) that uses this infrastructure but there
will be some by beginning 2012.
Reported-by: Sam Roberts <vieuxtech@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
skb->truesize might be big even for a small packet.
Its even bigger after commit 87fb4b7b53 (net: more accurate skb
truesize) and big MTU.
We should allow queueing at least one packet per receiver, even with a
low RCVBUF setting.
Reported-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes it to yield sooner at halfway instead. Still not a cure-all
for listener overrun if listner is slow, but works much reliably.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't inline functions that cover several lines, and do inline
the trivial ones. Also make some arguments const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting a large rps_flow_cnt like (1 << 30) on 32-bit platform will
cause a kernel oops due to insufficient bounds checking.
if (count > 1<<30) {
/* Enforce a limit to prevent overflow */
return -EINVAL;
}
count = roundup_pow_of_two(count);
table = vmalloc(RPS_DEV_FLOW_TABLE_SIZE(count));
Note that the macro RPS_DEV_FLOW_TABLE_SIZE(count) is defined as:
... + (count * sizeof(struct rps_dev_flow))
where sizeof(struct rps_dev_flow) is 8. (1 << 30) * 8 will overflow
32 bits.
This patch replaces the magic number (1 << 30) with a symbolic bound.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Userspace may not provide TCA_OPTIONS, in fact tc currently does
so not do so if no arguments are specified on the command line.
Return EINVAL instead of panicing.
Signed-off-by: Thomas Graf <tgraf@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 618f9bc74a (net: Move mtu handling down to the protocol
depended handlers) forgot the bridge netfilter case, adding a NULL
dereference in ip_fragment().
Reported-by: Chris Boot <bootc@bootc.net>
CC: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They don't need to disable interrupts anymore, we only run in process
context now.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
We simply say that regular this_cpu use must be safe regardless of
preemption and interrupt state. That has no material change for x86
and s390 implementations of this_cpu operations. However, arches that
do not provide their own implementation for this_cpu operations will
now get code generated that disables interrupts instead of preemption.
-tj: This is part of on-going percpu API cleanup. For detailed
discussion of the subject, please refer to the following thread.
http://thread.gmane.org/gmane.linux.kernel/1222078
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
LKML-Reference: <alpine.DEB.2.00.1112221154380.11787@router.home>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
RFCOMM needs a proper priority mechanism inside itself and not try to use
l2cap priority to fix its own problem.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Low Energy pairing is performed through the SMP (Security Manager Protocol)
mechanism rather than HCI.
Signed-off-by: Brian Gix <bgix@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
To achive Man-In-The-Middle (MITM) level security with Low Energy,
we have to enable User Passkey Comparison. This commit modifies the
hard-coded JUST-WORKS pairing mechanism to support query via the MGMT
interface of Passkey comparison and User Confirmation.
Signed-off-by: Brian Gix <bgix@codeaurora.org>
Acked-by: Marcel Holtmann<marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The struct hci_proto and all related register/unregister and dispatching
code was removed. HCI core code now call directly the SCO and L2CAP
event functions.
Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Make code readable by removing magic numbers.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
No local_bh_disable is needed there once we run everything in process
context. The same goes for the replacement of bh_lock_sock() by
lock_sock().
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: Add a flow_cache_flush_deferred function
ipv4: reintroduce route cache garbage collector
net: have ipconfig not wait if no dev is available
sctp: Do not account for sizeof(struct sk_buff) in estimated rwnd
asix: new device id
davinci-cpdma: fix locking issue in cpdma_chan_stop
sctp: fix incorrect overflow check on autoclose
r8169: fix Config2 MSIEnable bit setting.
llc: llc_cmsg_rcv was getting called after sk_eat_skb.
net: bpf_jit: fix an off-one bug in x86_64 cond jump target
iwlwifi: update SCD BC table for all SCD queues
Revert "Bluetooth: Revert: Fix L2CAP connection establishment"
Bluetooth: Clear RFCOMM session timer when disconnecting last channel
Bluetooth: Prevent uninitialized data access in L2CAP configuration
iwlwifi: allow to switch to HT40 if not associated
iwlwifi: tx_sync only on PAN context
mwifiex: avoid double list_del in command cancel path
ath9k: fix max phy rate at rate control init
nfc: signedness bug in __nci_request()
iwlwifi: do not set the sequence control bit is not needed
flow_cach_flush() might sleep but can be called from
atomic context via the xfrm garbage collector. So add
a flow_cache_flush_deferred() function and use this if
the xfrm garbage colector is invoked from within the
packet path.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master: (848 commits)
SELinux: Fix RCU deref check warning in sel_netport_insert()
binary_sysctl(): fix memory leak
mm/vmalloc.c: remove static declaration of va from __get_vm_area_node
ipmi_watchdog: restore settings when BMC reset
oom: fix integer overflow of points in oom_badness
memcg: keep root group unchanged if creation fails
nilfs2: potential integer overflow in nilfs_ioctl_clean_segments()
nilfs2: unbreak compat ioctl
cpusets: stall when updating mems_allowed for mempolicy or disjoint nodemask
evm: prevent racing during tfm allocation
evm: key must be set once during initialization
mmc: vub300: fix type of firmware_rom_wait_states module parameter
Revert "mmc: enable runtime PM by default"
mmc: sdhci: remove "state" argument from sdhci_suspend_host
x86, dumpstack: Fix code bytes breakage due to missing KERN_CONT
IB/qib: Correct sense on freectxts increment and decrement
RDMA/cma: Verify private data length
cgroups: fix a css_set not found bug in cgroup_attach_proc
oprofile: Fix uninitialized memory access when writing to writing to oprofilefs
Revert "xen/pv-on-hvm kexec: add xs_reset_watches to shutdown watches from old kernel"
...
Conflicts:
kernel/cgroup_freezer.c
Commit 2c8cec5c10 (ipv4: Cache learned PMTU information in inetpeer)
removed IP route cache garbage collector a bit too soon, as this gc was
responsible for expired routes cleanup, releasing their neighbour
reference.
As pointed out by Robert Gladewitz, recent kernels can fill and exhaust
their neighbour cache.
Reintroduce the garbage collection, since we'll have to wait our
neighbour lookups become refcount-less to not depend on this stuff.
Reported-by: Robert Gladewitz <gladewitz@gmx.de>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also use mod_timer() instead of direct assignment to "expires".
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A known Out Of Order (OOO) problem hurts SFQ when timer changes
perturbation value, since all new packets delivered to SFQ enqueue might
end on different slots than previous in-flight packets.
With round robin delivery, we can thus deliver packets in a different
order.
Since SFQ is limited to small amount of in-flight packets, we can rehash
packets so that this OOO problem is fixed.
This rehashing is performed only if internal flow classifier is in use.
We now store in skb->cb[] the "struct flow_keys" so that we dont call
skb_flow_dissect() again while rehashing.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mac80211 relays a frame from STA1 to STA2 in AP mode it will get
re-classified in the tx path. Unfortunately the frame protocol field
is always set to ETH_P_8023 while the classification only kicks in
for ETH_P_IP. Hence, a high priority frame from STA1 will be send to
STA2 as best effort.
Instead of running classification on the frame just use the same
priority as STA1 did. Do this by adding 256 to the skb->priority
to allow cfg80211_classify8021d to shortcut frame classification.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The IBSS merge code calls ieee80211_sta_expire() with a relatively
short expire timeout that purges other clients prematurely. The
expire function has to check that only the clients belonging to
the vif in question are purged.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
to record the state of SACK/FACK and DSACK for better readability and maintenance.
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The handling of SCO audio links and the L2CAP protocol are essential to
any system with Bluetooth thus are always compiled in from now on.
Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The hci_task_lock mutex (previously a lock) was supposed to protect the
register/unregister of HCI protocols against RX/TX tasks. This will not
be needed anymore because SCO and L2CAP will always be compiled.
Moreover, with the recent move of RX/TX to workqueues per device the
global hci_task_lock was causing starvation between different HCI
devices.
Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: Fix a regression in nfs_file_llseek()
NFSv4: Do not accept delegated opens when a delegation recall is in effect
NFSv4: Ensure correct locking when accessing the 'lock_states' list
NFSv4.1: Ensure that we handle _all_ SEQUENCE status bits.
NFSv4: Don't error if we handled it in nfs4_recovery_handle_error
SUNRPC: Ensure we always bump the backlog queue in xprt_free_slot
SUNRPC: Fix the execution time statistics in the face of RPC restarts
previous commit 3fb72f1e6e
makes IP-Config wait for carrier on at least one network device.
Before waiting (predefined value 120s), check that at least one device
was successfully brought up. Otherwise (e.g. buggy bootloader
which does not set the MAC address) there is no point in waiting
for carrier.
Cc: Micha Nelissen <micha@neli.hopto.org>
Cc: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It makes more sense this way, since info_timer is a timer using delayed
work API.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This one also needs to run in process context
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
af_iucv differs unnecessarily between state IUCV_SEVERED and
IUCV_DISCONN. This patch removes state IUCV_SEVERED.
While simplifying af_iucv, this patch removes the 2nd invocation of
cpcmd as well.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
af_iucv contains timer infrastructure which is not exploited.
This patch removes the timer related code parts.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For HiperSockets transport skbs sent are bound to one of the
available HiperSockets devices. Add missing release of reference to
a HiperSockets device before freeing an skb.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Closing an af_iucv socket may wait for confirmation of outstanding
send requests. This patch adds confirmation code for the new
HiperSockets transport.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AF_IUCV address family offers support for ancillary data.
This patch enables usage of ancillary data with the new
HiperSockets transport.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current controller initialization is moved tp bredr_init and new
function added amp_init to handle later AMP init sequence. Current
AMP init sequence include Reset and Read Local Version.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
When checking whether a DATA chunk fits into the estimated rwnd a
full sizeof(struct sk_buff) is added to the needed chunk size. This
quickly exhausts the available rwnd space and leads to packets being
sent which are much below the PMTU limit. This can lead to much worse
performance.
The reason for this behaviour was to avoid putting too much memory
pressure on the receiver. The concept is not completely irational
because a Linux receiver does in fact clone an skb for each DATA chunk
delivered. However, Linux also reserves half the available socket
buffer space for data structures therefore usage of it is already
accounted for.
When proposing to change this the last time it was noted that this
behaviour was introduced to solve a performance issue caused by rwnd
overusage in combination with small DATA chunks.
Trying to reproduce this I found that with the sk_buff overhead removed,
the performance would improve significantly unless socket buffer limits
are increased.
The following numbers have been gathered using a patched iperf
supporting SCTP over a live 1 Gbit ethernet network. The -l option
was used to limit DATA chunk sizes. The numbers listed are based on
the average of 3 test runs each. Default values have been used for
sk_(r|w)mem.
Chunk
Size Unpatched No Overhead
-------------------------------------
4 15.2 Kbit [!] 12.2 Mbit [!]
8 35.8 Kbit [!] 26.0 Mbit [!]
16 95.5 Kbit [!] 54.4 Mbit [!]
32 106.7 Mbit 102.3 Mbit
64 189.2 Mbit 188.3 Mbit
128 331.2 Mbit 334.8 Mbit
256 537.7 Mbit 536.0 Mbit
512 766.9 Mbit 766.6 Mbit
1024 810.1 Mbit 808.6 Mbit
Signed-off-by: Thomas Graf <tgraf@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise getting
| net/unix/diag.c:312:16: error: expected declaration specifiers or ‘...’ before string constant
| net/unix/diag.c:313:1: error: expected declaration specifiers or ‘...’ before string constant
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
(Thanks to Joe Perches for suggesting coccinelle for 0/1 -> true/false).
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
DaveM said:
Please, this kind of stuff rots forever and not using bool properly
drives me crazy.
Joe Perches <joe@perches.com> gave me the spatch script:
@@
bool b;
@@
-b = 0
+b = false
@@
bool b;
@@
-b = 1
+b = true
I merely installed coccinelle, read the documentation and took credit.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8ffd3208 voids the previous patches f6778aab and 810c0719 for
limiting the autoclose value. If userspace passes in -1 on 32-bit
platform, the overflow check didn't work and autoclose would be set
to 0xffffffff.
This patch defines a max_autoclose (in seconds) for limiting the value
and exposes it through sysctl, with the following intentions.
1) Avoid overflowing autoclose * HZ.
2) Keep the default autoclose bound consistent across 32- and 64-bit
platforms (INT_MAX / HZ in this patch).
3) Keep the autoclose value consistent between setsockopt() and
getsockopt() calls.
Suggested-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can use vzalloc() helper now instead of __vmalloc() trick
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Received non stream protocol packets were calling llc_cmsg_rcv that used a
skb after that skb was released by sk_eat_skb. This caused received STP
packets to generate kernel panics.
Signed-off-by: Alexandru Juncu <ajuncu@ixiacom.com>
Signed-off-by: Kunjan Naik <knaik@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 42624d4913
created following sparse warning
>net/mac80211/sta_info.c:965:24: warning: incorrect type in assignment (different address spaces)
>net/mac80211/sta_info.c:965:24: expected struct tid_ampdu_tx *tid_tx
>net/mac80211/sta_info.c:965:24: got struct tid_ampdu_tx [noderef] <asn:4>*<noident>
Making use of rcu_dereference_protected to fix the problem.
V2:
- Replacing rcu_dereference with rcu_dereference_protected
as suggested by Johannes.
- Adding mutex_lock/unlock to satisfy the condition at
rcu_dereference_protected
Cc: Nishant Sarmukadam <nishants@marvell.com>
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 5c3ddec73d.
S390 qeth driver actually still uses the setup ops.
Reported-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a struct sk_buff pointer and it should be freed with kfree_skb()
instead of kfree().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We unlock inside the if block on the other side of this if else
statement. It could result in calling mutex_unlock() twice.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a peer changes SMPS state we should update
rate control so it doesn't have to detect it by
itself. It can't detect "dynamic" mode anyway
since that just requires rts-cts handshaking.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
llcp_mac routines should be static and inlined or build will fail with NFC
selected without LLCP.
This patch fixes:
LD [M] net/nfc/nfc.o
net/nfc/netlink.o: In function `nfc_llcp_mac_is_down':
netlink.c:(.text+0x0): multiple definition of `nfc_llcp_mac_is_down'
net/nfc/core.o:(.text+0x0): first defined here
net/nfc/netlink.o: In function `nfc_llcp_mac_is_up':
netlink.c:(.text+0x10): multiple definition of `nfc_llcp_mac_is_up'
net/nfc/core.o:(.text+0x10): first defined here
net/nfc/af_nfc.o: In function `nfc_llcp_mac_is_down':
(.text+0x0): multiple definition of `nfc_llcp_mac_is_down'
net/nfc/core.o:(.text+0x0): first defined here
net/nfc/af_nfc.o: In function `nfc_llcp_mac_is_up':
(.text+0x10): multiple definition of `nfc_llcp_mac_is_up'
net/nfc/core.o:(.text+0x10): first defined here
net/nfc/rawsock.o: In function `nfc_llcp_mac_is_down':
rawsock.c:(.text+0x0): multiple definition of `nfc_llcp_mac_is_down'
net/nfc/core.o:(.text+0x0): first defined here
net/nfc/rawsock.o: In function `nfc_llcp_mac_is_up':
rawsock.c:(.text+0x10): multiple definition of `nfc_llcp_mac_is_up'
net/nfc/core.o:(.text+0x10): first defined here
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If station info contains a beacon loss count, return
it to userspace.
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently code allows three (HT_AGG_MAX_RETRIES) unanswered addba
requests. When this limit is reached aggregation is turned off for
given TID permanently. This doesn't seem right: three requests is
not that much, some 'blackout' can happen, but effect of it affects
whole connection indefinitely.
This patch increases number of retries to 15. Also, when there have
been 3 or more retries it splits further retries apart by 15 seconds
instead of sending them in very short period of time.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 4dff523a91.
It was reported that this patch cause issues when trying to connect to
legacy devices so reverting it.
Reported-by: David Fries <david@fries.net>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
When the last RFCOMM data channel is closed, a timer is normally set
up to disconnect the control channel at a later time. If the control
channel disconnect command is sent with the timer pending, the timer
needs to be cancelled.
If the timer is not cancelled in this situation, the reference
counting logic for the RFCOMM session does not work correctly when the
remote device closes the L2CAP connection. The session is freed at
the wrong time, leading to a kernel panic.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
When configuring an ERTM or streaming mode connection, remote devices
are expected to send an RFC option in a successful config response. A
misbehaving remote device might not send an RFC option, and the L2CAP
code should not access uninitialized data in this case.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Incoming sk_buffs always have bt_cb(skb)->force_active set to 0, so
it's misleading to use that value from the control block when calling
hci_conn_enter_active_mode() for incoming data. The destination socket
is not known in the HCI layer, so the force_active setting for each
socket isn't known either. Hard-coding the force_active parameter does
not change any behavior, but makes it obvious that incoming ACL data
never exits sniff mode.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Simplify function and remove fourth level of indentation.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Implement block size read function. Use different variables for
packet-based and block-based flow control.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch fixes user_confirm_neg_reply to use the appropriate struct
for accessing the call parameters.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
We do not want the service cache to be enabled indefinitely after
mgmt_read_info is called. To solve this a timer is added which will
automatically disable the cache if mgmt_set_dev_class isn't called
within 5 seconds of calling mgmt_read_info.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Due to the upcoming addition of a service cache timer the functions to
update the EIR and CoD need to be higher up in mgmt.c in order to avoid
unnecessary forward-declarations. This patch simply moves code around
without any other changes in order to make subsequent patches more
readable.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Instead of having an explicit service cache command we can make the mgmt
API simpler by implicitly enabling the cache when mgmt_read_info is
called for the first time and disabling it when mgmt_set_dev_class is
called.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Fast connectable is logically after the connectable property so that's
where it should show up in the code as well (it's also after connectable
in the settings bitfield).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch updates the mgmt_read_info and related messages to the latest
management API which uses a bitfield of settings instead of individual
boolean values.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
hdev->workqueue should be only for rx/tx, so move this one out.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
As we run in process context now we don't need worqueue to add e del from
sysfs.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Update hdev workqueue API usage to use the new interface, this new
interface also allow us to mark this workqueue as WQ_HIGHPRI, so now rx
and tx work gets higher priority when running.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
hdev->workqueue will be only for for rx/tx/cmd processing, all other small
works should go to the system workqueue for now.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This list has much more reads than writes, so RCU makes senses here, also
it avoid deadlock against the socket lock.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This move some checking code that was in l2cap_sock_connect() to
l2cap_chan_connect(). Thus we can invert the lock calls, i.e., call
lock_sock() before hci_dev_lock() to avoid a deadlock scenario.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Another step of remove interrupt context from Bluetooth Core.
Use the system workqueue.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This should simplify Bluetooth core processing a lot.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
As part of the moving on all the Bluetooth processing to Process context.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
It's pointless, we aren't protecting anything since btusb_notify()
schedules a work to run, then all it operation happens without protection.
If protection is really needed here, we will fix it further.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Handling hci_conn_hash with RCU make us avoid some locking and disable
tasklets.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Instead of using tasklet_disable() to prevent acess to the channel use, we
can use RCU and improve the performance of our code.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
spin lock doesn't fit ok anymore on the new code based on workqueues.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Now we can sleep in any path inside Bluetooth core, so mutex can make
sense here.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
We run everything in the same lock now. The backlog queue is useless now
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
We now run everything in process context, so the mutex lock is the best
option. But in some places we still need the bh_lock_sock()
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
L2CAP timers also need to run in process context. As the works in l2cap
are small we are using the system worqueue.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
It doesn't really touch any sensitive information about hdev. So no need
to lock here.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
As HCI rx path is now done in process context it makes sense to do all the
timer in process context as well.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth rx task runs now in a workqueue, so it a good approach run any
timer that share locking with process context code also in a workqueue.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Now we run everything in HCI in process context, so it's a better idea use
mutex instead spin_lock. The macro remains hci_dev_lock() (and I got rid
of hci_dev_lock_bh()), of course.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Run recv process in workqueue helps a lot with our processing as the recv
path will also be in the process context, i.e., now all our tx and rx are
in process context.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Use the expect tuple (if possible) instead of the master tuple for
the get operation. If two or more expectations come from the same
master, the returned expectation may not be the one that user-space
is requesting.
This is how it works for the expect deletion operation.
Although I think that nobody has been seriously using this. We
accept both possibilities, using the expect tuple if possible.
I decided to do it like this to avoid breaking backward
compatibility.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We can use atomic64_t infrastructure to avoid taking a spinlock in fast
path, and remove inaccuracies while reading values in
ctnetlink_dump_counters() and connbytes_mt() on 32bit arches.
Suggested by Pablo.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use IS_ENABLED(CONFIG_FOO)
instead of defined(CONFIG_FOO) || defined (CONFIG_FOO_MODULE)
Signed-off-by: Igor Maravić <igorm@etf.rs>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use IS_ENABLED(CONFIG_FOO)
instead of defined(CONFIG_FOO) || defined (CONFIG_FOO_MODULE)
Signed-off-by: Igor Maravić <igorm@etf.rs>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use IS_ENABLED(CONFIG_FOO)
instead of defined(CONFIG_FOO) || defined (CONFIG_FOO_MODULE)
Signed-off-by: Igor Maravić <igorm@etf.rs>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller
Patrick McHardy