* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Cacheops.h: Fix typo.
[MIPS] Cobalt: Qube1 has no serial port so don't use it
[MIPS] Cobalt: Fix ethernet interrupts for RaQ1
[MIPS] Kconfig fixes for BCM47XX platform
This reverts commit 2e6883bdf4, as
requested by Fengguang Wu. It's not quite fully baked yet, and while
there are patches around to fix the problems it caused, they should get
more testing. Says Fengguang: "I'll resend them both for -mm later on,
in a more complete patchset".
See
http://bugzilla.kernel.org/show_bug.cgi?id=9738
for some of this discussion.
Requested-by: Fengguang Wu <wfg@mail.ustc.edu.cn>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 5d2efba64b changed our iommu code
so that it always uses an iommu page size of 4kB. That means with our
current code, drivers may do a dma_map_sg() of a 64kB page and obtain
a dma_addr_t that is only 4k aligned.
This works fine in most cases except for some infiniband HW it seems,
where they tell the HW about the page size and it ignores the low bits
of the DMA address.
This works around it by making our IOMMU code enforce a PAGE_SIZE alignment
for mappings of objects that are page aligned in the first place and whose
size is larger or equal to a page.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
After 9b8e8de7, manage_start_stop configuration depends on valid ATA
device. Move it into ata_scsi_dev_config(). This was detected by the
coverity checker.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
CERR reports errors detected during executing a command. This doesn't
mean the error is tied to the command and can be recovered by just
issuing it again. Many of the errors are fatal port-wide connditions
including HSM violation, host bus error and ATA bus error and require
freezing and port reset.
The freezing part wasn't implemented previously. This used to be okay
because port resets were scheduled anyway and EH eventually resets and
recovers the port. With PMP support added, this is no longer true.
The error condition and recover actions are attributed to the fan-out
port and the host port condition isn't properly recovered leading to
EH failures.
This patch makes CERR errors which require resets to freeze the port.
This will force host port reset and proper recovery.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Andrew Ryder <tireman@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Because Qube1 doesn't have a serial chip waiting for transmit fifo empty
takes forever, which isn't a good idea. No prom_putchar/early console
for Qube1 fixes this.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
RAQ1 uses the same interrupt routing as Qube2.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The patch below fixes two problems for Kconfig on the BCM47xx platform:
- arch/mips/bcm47xx/gpio.c uses ssb_extif_* functions. Selecting
SSB_DRIVER_EXTIF makes sure those functions are available.
- arch/mips/pci/pci.c needs, when enabled, platform specific functions,
which are defined when SSB_PCICORE_HOSTMODE is enabled.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 84427eaef1 (remove task_ppid_nr_ns)
moved the task_tgid_nr_ns(task->real_parent) outside of lock_task_sighand().
This is wrong, ->real_parent could be freed/reused.
Both ->parent/real_parent point to nothing after __exit_signal() because
we remove the child from ->children list, and thus the child can't be
reparented when its parent exits.
rcu_read_lock() protects ->parent/real_parent, but _only_ if we know it was
valid before we take rcu lock.
Revert this part of the patch.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the registration of the second I2C channel fails, we really want to
unregister the first one before we return with an error.
While we're here, fix the printk right above so that it displays the
real driver name.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
This patch fixes bug #9581 reported by Marcio Buss. If kzalloc fails,
omap_i2c_write_reg() tries to reset an unallocated I2C controller.
Cc: Marcio Buss <marciobuss@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: improve Kconfig help entries for HP Jornada devices
Input: pass EV_PWR events to event handlers
Input: spitzkbd - fix suspend key handling
gameport: don't export functions that are static inline
Input: jornada680_kbd - fix default keymap
Input: Handle EV_PWR type of input caps in input_set_capability.
Fix array overflows in the OSS msnd driver spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes compilation error where i2c_init wasn't defined.
Also, remove the CVS log and version tags, they are no longer useful.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark uvesafb_init_mtrr() as __devinit since its caller is __devinit
and since it accesses __devinitdata.
WARNING: vmlinux.o(.text+0x4df80e): Section mismatch: reference to .init.data: (between 'uvesafb_init_mtrr' and 'uvesafb_show_vbe_ver')
Variable 'blank' cannot be __devinitdata since it is referenced in an
fb_ops method that could be called at any time.
WARNING: vmlinux.o(.text+0x4dfc1e): Section mismatch: reference to .init.data:blank (between 'param_set_scroll' and 'vesa_setpalette')
WARNING: vmlinux.o(.text+0x4dfc24): Section mismatch: reference to .init.data:blank (between 'param_set_scroll' and 'vesa_setpalette')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes compile error when nr_free_pages() from linux/swap.h
expands to global_page_state(NR_FREE_PAGES), but linux/vmstat.h isn't
included to declare global_page_state().
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a kernel panic on boot due to do_signal not being compatible
with it's callers.
- do_signal now returns void, and does not have the previous signal set
as a parameter.
- Remove sys_rt_sigsuspend, we can use the common one instead.
- Change sys_sigsuspend to be more like x86, don't call do_signal here.
- handle_signal, setup_frame and setup_rt_frame now return -EFAULT
if we've delivered a segfault, which is used by callers to perform
necessary cleanup.
- Break long lines, correct whitespace and formatting errors.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows us to use the commong sys_rt_sigsuspend instead of
having our own.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix wrong pointer type passed into the s3c2410fb_init_registers()
function.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the error path of both shared and private hugetlb page allocation,
the file system quota is never undone, leading to fs quota leak. Fix
them up.
[akpm@linux-foundation.org: cleanup, micro-optimise]
Signed-off-by: Ken Chen <kenchen@google.com>
Acked-by: Adam Litke <agl@us.ibm.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: William Lee Irwin III <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark cciss_pci_init() as __devinit, to fix section mismatch warning.
WARNING: vmlinux.o(.text+0x601fc9): Section mismatch: reference to .init.text: (between 'cciss_pci_init' and 'cciss_getgeometry')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: <mike.miller@hp.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WARNING: vmlinux.o(.text+0x2a4462): Section mismatch: reference to .exit.text:qla2x00_remove_one (between 'qla2xxx_pci_error_detected' and 'qla2x00_stop_timer')
qla2x00_remove_one() mustn't be __devexit since it's called from
qla2xxx_pci_error_detected().
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Seokmann Ju <seokmann.ju@qlogic.com>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the user has turned on the "restore_caplock_events" parameter, the
code mangles the capslock events correctly, then erroneously ignores
those events. Fix logic to allow correct fallthrough.
Signed-off-by: Andy Wingo <wingo@pobox.com>
Acked-by: Andrew McNabb <amcnabb@mcnabbs.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Quicklists calculates the size of the quicklists based on the number of
free pages. This must be the number of free pages that can be allocated
with GFP_KERNEL. node_page_state() includes the pages in ZONE_HIGHMEM and
ZONE_MOVABLE which may lead the quicklists to become too large causing OOM.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Tested-by: Dhaval Giani <dhaval@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The savestate command structure was being overwritten by the result of
running the TPM_SaveState command after one run, so make it a local
variable to the function instead of a global variable that gets
overwritten.
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Kent Yoder <shpedoikal@gmail.com>
Cc: Marcel Selhorst <tpm@selhorst.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sometimes cpu_idle_wait gets stuck because it might miss CPUS that are
already in idle, have no tasks waiting to run and have no interrupts going
to them. This is common on bootup when switching cpu idle governors.
This patch gives those CPUS that don't check in an IPI kick.
Background:
-----------
I notice this while developing the mcount patches, that every once in a
while the system would hang. Looking deeper, the hang was always at boot
up when registering init_menu of the cpu_idle menu governor. Talking
with Thomas Gliexner, we discovered that one of the CPUS had no timer
events scheduled for it and it was in idle (running with NO_HZ). So the
CPU would not set the cpu_idle_state bit.
Hitting sysrq-t a few times would eventually route the interrupt to the
stuck CPU and the system would continue.
Note, I would have used the PDA isidle but that is set after the
cpu_idle_state bit is cleared, and would leave a window open where we
may miss being kicked.
hmm, looking closer at this, we still have a small race window between
clearing the cpu_idle_state and disabling interrupts (hence the RFC).
CPU0: CPU 1:
--------- ---------
cpu_idle_wait(): cpu_idle():
| __cpu_cpu_var(is_idle) = 1;
| if (__get_cpu_var(cpu_idle_state)) /* == 0 */
per_cpu(cpu_idle_state, 1) = 1; |
if (per_cpu(is_idle, 1)) /* == 1 */ |
smp_call_function(1) |
| receives ipi and runs do_nothing.
wait on map == empty idle();
/* waits forever */
So really we need interrupts off for most of this then. One might think
that we could simply clear the cpu_idle_state from do_nothing, but I'm
assuming that cpu_idle governors can be removed, and this might cause a
race that a governor might be used after the module was removed.
Venki said:
I think your RFC patch is the right solution here. As I see it, there is
no race with your RFC patch. As long as you call a dummy smp_call_function
on all CPUs, we should be OK. We can get rid of cpu_idle_state and the
current wait forever logic altogether with dummy smp_call_function. And so
there wont be any wait forever scenario.
The whole point of cpu_idle_wait() is to make all CPUs come out of idle
loop atleast once. The caller will use cpu_idle_wait something like this.
// Want to change idle handler
- Switch global idle handler to always present default_idle
- call cpu_idle_wait so that all cpus come out of idle for an instant
and stop using old idle pointer and start using default idle
- Change the idle handler to a new handler
- optional cpu_idle_wait if you want all cpus to start using the new
handler immediately.
Maybe the below 1s patch is safe bet for .24. But for .25, I would say we
just replace all complicated logic by simple dummy smp_call_function and
remove cpu_idle_state altogether.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Decrement the slave counter only in ->release() callback instead of both
in ->release() and w1 control.
Patch is based on debug work and preliminary patch made by Henri Laakso.
Henri noticed in debug that this counter becomes negative after w1 slave
device is physically removed.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Henri Laakso <henri.laakso@wapice.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kyle McMartin reports sysrq_timer_list_show() can hit the module mutex
from hard interrupt context. These paths don't need to though, since we
long ago changed all the module list manipulation to occur via
stop_machine().
Disabling preemption is enough.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
spidernet MAINTAINERship update
sky2: remove check for PCI wakeup setting from BIOS
sky2: large memory workaround.
fs_enet: check for phydev existence in the ethtool handlers
[usb netdev] asix: fix regression
r8169: fix missing loop variable increment
ip1000: menu location change
Fixed a small typo in the loopback driver
3c509: PnP resource management fix
netxen: fix byte-swapping in tx and rx
netxen: optimize tx handling
netxen: stop second phy correctly
netxen: update driver version
netxen: update MAINTAINERS
endianness noise in tulip_core
de4x5 fixes
xircom_cb endianness fixes
rt2x00: Put 802.11 data on 4 byte boundary
rt2x00: Corectly initialize rt2500usb MAC
rt2x00: Allow rt61 to catch up after a missing tx report
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fix CPU hotplug when using the SLB shadow buffer
[POWERPC] efika: add phy-handle property for fec_mpc52xx
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
pnpacpi: print resource shortage message only once
PM: ACPI and APM must not be enabled at the same time
ACPI: apply quirk_ich6_lpc_acpi to more ICH8 and ICH9
ACPICA: fix acpi_serialize hang regression
ACPI : Not register gsi for PCI IDE controller in legacy mode
ACPI: Reintroduce run time configurable max_cstate for !CPU_IDLE case
ACPI: Make sysfs interface in ACPI power optional.
ACPI: EC: Enable boot EC before bus_scan
increase PNP_MAX_PORT to 40 from 24
When RPCSEC/GSS and krb5i is used, requests are padded, typically to a multiple
of 8 bytes. This can make the request look slightly longer than it
really is.
As of
f34b95689d "The NFSv2/NFSv3 server does not handle zero
length WRITE request correctly",
the xdr decode routines for NFSv2 and NFSv3 reject requests that aren't
the right length, so krb5i (for example) WRITE requests can get lost.
This patch relaxes the appropriate test and enhances the related comment.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Cc: Peter Staubach <staubach@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
task_ppid_nr_ns is called in three places. One of these should never
have called it. In the other two, using it broke the existing
semantics. This was presumably accidental. If the function had not
been there, it would have been much more obvious to the eye that those
patches were changing the behavior. We don't need this function.
In task_state, the pid of the ptracer is not the ppid of the ptracer.
In do_task_stat, ppid is the tgid of the real_parent, not its pid.
I also moved the call outside of lock_task_sighand, since it doesn't
need it.
In sys_getppid, ppid is the tgid of the real_parent, not its pid.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we switched away from the optimized C version
things stopped being monotonic.
The problem is that if we run this with interrupts disabled, we can
see the interrupt pending because the counter reached the limit value.
When this happens the counter has bit 31 set, and the low bits start
counting again from zero.
Reported by Martin Habets.
Signed-off-by: David S. Miller <davem@davemloft.net>
pnpacpi: exceeded the max number of IO resources: 40
While this message is a real error and should thus
remain KERN_ERR (even a new dmesg line is seen as a regression
by some, since it was not printed in 2.6.23...) it is certainly
impolite to print this warning 50 times should you happen to
have the oddball system with 90 io resources under a device...
So print the warning just once.
In 2.6.25 we'll get rid of the limits altogether
and these warnings will vanish with them.
http://bugzilla.kernel.org/show_bug.cgi?id=9535
Signed-off-by: Len Brown <len.brown@intel.com>
The driver checks status of PCI power management to mark
default setting of Wake On Lan. On some systems this works, but often
it reports a that WOL is disabled when it isn't.
This patch gets rid of that check and just reports the wake on
lan status based on the hardware capablity.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Linus Torvalds