This patch adds support for txx9wdt driver to rbhma3100, rbhma4200 and
rbhma4500 platform.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
R10k non coherent machines need a real dma cache invalidate to get rid of
speculative stores in cache. For other machines this promises a slight
speedup.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move registration into the actual platform code instead of making a
desparate attempt at sharing the hand full of likes of code in pcspeaker.c.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Given that the corresponding source file i2c-yosemite.c file was
removed in commit daa4a68f90, and that
no one else includes this file, it seems safe to delete it.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use strchr instead of strstr when searching for a single character
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since all the callers of the PHYS_TO_XKPHYS macro call with a constant,
put the cast to LL inside the macro where it really should be rather
than in all the callers. This makes macros like PHYS_TO_XKSEG_UNCACHED
work without gcc whining.
Signed-off-by: Andrew Sharp <andy.sharp@onstor.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Removed unused mips_machtype. These are only set but not used.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove some unnecessary codes, includes and files.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This complements the generic R4000/R4400 errata workaround code and adds
bits for the daddiu problem. In most places it just modifies handwritten
assembly code so that the assembler is allowed to use a temporary register
as daddiu may now be treated as a macro that expands to a sequence of li
and daddu. It is the AT register or, where AT is unavailable or used
explicitly for another purpose, an explicitly-named register is selected,
using the .set at=<reg> feature added recently to gas. This feature is
only used if CONFIG_CPU_DADDI_WORKAROUNDS has been set, so if the
workaround remains disabled, the required version of binutils stays
unchanged.
Similarly, daddiu instructions put in branch delay slots in noreorder
fragments are now taken out of them and the assembler is allowed to
reorder them itself as possible (which it does making the whole idea of
scheduling them into delay slots manually questionable).
Also in the very few places where such a simple conversion was not
possible, a handcoded longer sequence is implemented.
Other than that there are changes to code responsible for building the
TLB fault and page clear/copy handlers to avoid daddiu as appropriate.
These are only effective if the erratum is verified to be present at the
run time.
Finally there is a trivial update to __delay(), because it uses daddiu in
a branch delay slot.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is the gereric part of R4000/R4400 errata workarounds. They include
compiler and assembler support as well as some source code modifications
to address the problems with some combinations of multiply/divide+shift
instructions as well as the daddi and daddiu instructions.
Changes included are as follows:
1. New Kconfig options to select workarounds by platforms as necessary.
2. Arch top-level Makefile to pass necessary options to the compiler; also
incompatible configurations are detected (-mno-sym32 unsupported as
horribly intrusive for little gain).
3. Bug detection updated and shuffled -- the multiply/divide+shift problem
is lethal enough that if not worked around it makes the kernel crash in
time_init() because of a division by zero; the daddiu erratum might
also trigger early potentially, though I have not observed it. On the
other hand the daddi detection code requires the exception subsystem to
have been initialised (and is there mainly for information).
4. r4k_daddiu_bug() added so that the existence of the erratum can be
queried by code at the run time as necessary; useful for generated code
like TLB fault and copy/clear page handlers.
5. __udelay() updated as it uses multiplication in inline assembly.
Note that -mdaddi requires modified toolchain (which has been maintained
by myself and available from my site for ~4years now -- versions covered
are GCC 2.95.4 - 4.1.2 and binutils from 2.13 onwards). The -mfix-r4000
and -mfix-r4400 have been standard for a while though.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (197 commits)
sh: add spi header and r2d platform data V3
sh: update r7780rp interrupt code
sh: remove consistent alloc stuff from the machine vector
sh: use declared coherent memory for dreamcast pci ethernet adapter
sh: declared coherent memory support V2
sh: Add support for SDK7780 board.
sh: constify function pointer tables
sh: Kill off -traditional for linker script.
cdrom: Add support for Sega Dreamcast GD-ROM.
sh: Kill off hs7751rvoip reference from arch/sh/Kconfig.
sh: Drop r7780rp_defconfig, use r7780mp_defconfig as kbuild default.
sh: Kill off dead HS771RVoIP board support.
sh: r7785rp: Fix up DECLARE_INTC_DESC() arg mismatch.
sh: r7785rp: Hook up the rest of the HL7785 FPGA IRQ vectors.
sh: r2d - enable sm501 usb host function
sh: remove voyagergx
sh: r2d - add lcd planel timings to sm501 platform data
sh: Add OHCI and UDC platform devices for SH7720.
sh: intc - remove default interrupt priority tables
sh: Correct pte size mismatch for X2 TLB.
...
* orion: (26 commits)
[ARM] Orion: implement power-off method for QNAP TS-109/209
[ARM] Orion: add support for QNAP TS-109/TS-209
[ARM] Orion: I2C support
[I2C] i2c-mv64xxx: Don't set i2c_adapter.retries
[I2C] Split mv643xx I2C platform support
[ARM] Orion: enable CONFIG_RTC_DRV_M41T80 for D-Link DNS-323
[ARM] Orion defconfig
[ARM] Orion: add support for Orion/MV88F5181 based D-Link DNS-323
[ARM] Orion: MV88F5181 support bits
[ARM] Orion: Buffalo/Revogear Kurobox Pro support
[ARM] OrionNAS RD board support
[ARM] Orion: support for Marvell Orion-2 (88F5281) Development Board
[ARM] Orion: common platform setup for Gigabit Ethernet port
[ARM] Orion: platform device registration for UART, USB and NAND
[ARM] Orion: system timer support
[ARM] Orion edge GPIO IRQ support
[ARM] Orion: IRQ support
[ARM] Orion: provide GPIO method for enabling hardware assisted blinking
[ARM] Orion: GPIO support
[ARM] Orion: programable address map support
...
Conflicts:
arch/arm/Kconfig
arch/arm/Makefile
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add armclk to the supported clocks on the S3C2440 and S3C2442 to
better represent the DVS state which controls whether FCLK or HCLK
is fed to the ARM core.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Merge together the bits of the S3C2440 and S3C2442 clock code
that can be.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the reverse of s3c2410_gpio_getirq to convert
a IRQ number into a GPIO pin number.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In the S3C2412 fclk is derived from msysclk, not straight from
the MPLL output. Set clk_f.parent appropriately.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The msysclk clock was checking for the wrong PLL for the
parent in s3c2412_setparent_msysclk(), trying the UPLL instead
of the MPLL output.
Also ensure the mpll and fclks are at the same rate at init time.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the channel parameter to s3c2410_dma_ctrl() in s3c2410_dma_enqueue()
if the S3C2410_DMAF_AUTOSTART is set on the channel.
Spotted by Steven Ryu at Samsung.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The s3c2410_dma_request() function should return the channel allocated
instead of zero for success.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The core resume code may have caused glitches in the GPIO when
restoring the GPIO state due to the order in which the GPIO registers
were being written.
Change the restore process take into account the state of the
GPIOs on resume and the state the system wants to restore them to.
See the code comments in the patch for more details of the process.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the call s3c2410_gpio_getpull() to return the
current state of the pin's pull-up.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If an DMA channel was active at suspend, then ensure that
it is correctly reconfigured when the system resumes.
Note, the previous policy was for each driver to handle their
own reconfiguration on resume. The policy has been changed to
make the individual driver's job easier.
Signed-off-by: Ben Dooks <ben-linux@flfuf.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current S3C24XX DMA code does not allow for an peripheral
that has one channel for RX and another for TX.
This patch adds a per-cpu dma operation to select the transmit
or receive channel, and adds support to the S3C2412 for the
seperate DMA channels for TX and RX.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add s3c2412_gpio_set_sleepcfg() to allow the setting of the sleep
configuration of the GPIO blocks.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add armclk to the S3C2412 to indicate the current clock connected to
the ARM core.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add checks for clk_set_rate() and ensure that we do not allow set_rate
to be called for a clock that does not have it defined. Add default
methods for fclk, hclk, pclk and mpll.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Check if the sleep command returns due to a pending interrupt
in the standby unit. If this happens, try and ack the IRQ
before re-trying the resume.
It is currently unclear whether the resume can be backed out
of at this stage as this could cause a problem with level
based interrupts.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure that if the RTC IRQ is not selected for wake in the
base configuration, then the PWRCFG has the same value set
in it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The IIS device is being registered by the Simtec Audio
driver, and thus registering here causes an error due
to device tree naming collision.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The IIS device is being registered by the Simtec Audio
driver, and thus registering here causes an error due
to device tree naming collision.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
S3C2412_GPESLPCON does not exist in the register
mappings, so remove it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The IIS and SDI register hw_addr definitions are
incorrect in the DMA map for the S3C2412.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
