SCIF modules which have SCSPTR can output the break signal. Now that we
have a way of determining port features/capabilities, add trivial break
control via SCSPTR support. Tested on sh7757lcr.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds initial support for requesting the various GPIO functions
necessary for certain ports. This just plugs in dumb request/free logic,
but serves as a building block for migrating off of the ->init_pins mess
to a wholly gpiolib backed solution (primarily parts with external
RTS/CTS pins, but will also allow us to clean up RXD pin testing).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The bulk of the ports do not support any sort of modem control, so
blindly twiddling the MCE bit doesn't accomplish much. We now require
ports to manually specify which line supports modem control signals.
While at it, tidy up the RTS/CTSIO handling in SCSPTR parts so it's a bit
more obvious what's going on (and without clobbering other configurations
in the process).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up support for SH-2(A) SCIFs by introducing a new regtype. As
expected, it's close to the SH-4A SCIF with fifodata, but still different
enough to warrant its own type.
Fixes up a number of FIFO overflows and similar for both SH7203/SH7264.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Tested-by: Federico Fuga <fuga@studiofuga.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
On some sh-mobile systems there are more than one DMA controllers, that
can be used for serial ports. Specifying a DMA device in sh-sci platform
data unnecessarily restricts the driver to only use one DMA controller.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
[Fixed the trivial conflict in include/linux/serial_sci.h]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Presently these were all using the same static string with no regard to
dev_name() and the like. This implements a bit of rework to name the IRQ
dynamically, as it should have been doing all along anyways.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This takes a bit of a sledgehammer to the horribly CPU subtype
ifdef-ridden header and abstracts all of the different register layouts
in to distinct types which in turn can be overriden on a per-port basis,
or permitted to default to the map matching the port type at probe time.
In the process this ultimately fixes up inumerable bugs with mismatches
on various CPU types (particularly the legacy ones that were obviously
broken years ago and no one noticed) and provides a more tightly coupled
and consolidated platform for extending and implementing generic
features.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Non-SCI parts do not have the special port reg necessary for cases where
the RX and SCI pins are muxed and need to be manually polled, so these
like always fall back on the normal FIFO processing paths. SH7760 is in a
class in and of itself with regards to mapping its SIM card interface via
the SCI port class despite not having any of the RXD lines wired up and
so implicitly behaving more like a SCIF in this regard. Out of the other
CPUs, some support the port check via the same block while others do it
through an external SuperI/O, so it's not even possible to perform the
check relative to the ioremapped cookie offset, so the separate read
semantics are preserved here, too.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This consolidates all of the broken out overrun handling and ensures that
we have sensible defaults per-port type, in addition to making sure that
overruns are flagged appropriately in the error mask for parts that
haven't explicitly disabled support for it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There's nothing worth hiding under the ifdef in the platform DMA
definitions, and we certainly don't want board code adding this in to
their platform data definitions, so we always expose the slave rx/tx
and device pointer members instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All of the muxed IRQs presently populate the IRQ array verbosely, this
simply provides a trivial helper to do it for them.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All users of the platform port data specify a mapbase where the driver
later derives the membase from. Now that UPF flags are taken in to
account for generic ioremapping we can kill off the port-specific membase
clobbering and simply use the generic paths.
This derives from a time when sh64 was not capable of using the generic
ioremap implementation and had employed early bolted DTLB mappings for
port access, which is no longer an issue.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch replaces the sh_dmae_slave_chan_id enum
with an unsigned int. The purpose of this chainge is
to make it possible to separate the slave id enums
from the dmaengine header.
The slave id enums varies with processor model, so in
the future it makes sense to put these in the processor
specific headers together with the pinmux enums.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Support using DMA for sending and receiving data over SCI(F) interfaces of
various SH SoCs.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This permits each port to select its own SCBRR calculation algorithm,
rather than having it all ifdef'ed in the header. There are presently
only 5 different variations that all parts fall under.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use enable/disable hooks for clock framework integration.
Make sure we control the clock for the serial console as well.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This header is needed on other architectures as well (namely h8300),
which currently fails to build without this in place. Rather than
duplicating the port definition completely there, just move this to a
common location instead.
This should get h8300 working again for 2.6.25, in addition to the
changes already pushed by Sato-san in -rc2.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Shimoda, Yoshihiro