Since older kernels may look in the sb_bad_features2 slot for flags,
rather than zeroing it out on fixup, we should make it equal to the
sb_features2 value.
Also, if the ATTR2 flag was not found prior to features2 fixup, it was not
set in the mount flags, so re-check after the fixup so that the current
session will use the feature.
Also fix up the comments to reflect these changes.
SGI-PV: 980085
SGI-Modid: xfs-linux-melb:xfs-kern:30778a
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Due to the xfs_dsb_t structure not being 64 bit aligned, the last field of
the on-disk superblock can vary in location This causes problems when the
filesystem gets moved to a different platform, or there is a 32 bit
userspace and 64 bit kernel.
This patch detects the defect at mount time, logs a warning such as:
XFS: correcting sb_features alignment problem
in dmesg and corrects the problem so that everything is OK. it also
blacklists the bad field in the superblock so it does not get used for
something else later on.
SGI-PV: 977636
SGI-Modid: xfs-linux-melb:xfs-kern:30539a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Remove macro-to-small-function indirection from xfs_sb.h, and remove some
which are completely unused.
SGI-PV: 976035
SGI-Modid: xfs-linux-melb:xfs-kern:30528a
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Donald Douwsma <donaldd@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
If the radix_tree_preload() fails, we need to destroy the inode we just
read in before trying again. This could leak xfs_vnode structures when
there is memory pressure. Noticed by Christoph Hellwig.
SGI-PV: 977823
SGI-Modid: xfs-linux-melb:xfs-kern:30606a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
wakeups
Idle state is not being detected properly by the xfsaild push code. The
current idle state is detected by an empty list which may never happen
with mostly idle filesystem or one using lazy superblock counters. A
single dirty item in the list that exists beyond the push target can
result repeated looping attempting to push up to the target because it
fails to check if the push target has been acheived or not.
Fix by considering a dirty list with everything past the target as an idle
state and set the timeout appropriately.
SGI-PV: 977545
SGI-Modid: xfs-linux-melb:xfs-kern:30532a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
the "ikeep" option is set rather than "noikeep".
This regression was introduced in 970451.
With no mount options specified, xfs_parseargs() does the following:
int ikeep = 0;
args->flags |= XFSMNT_BARRIER;
args->flags2 |= XFSMNT2_COMPAT_IOSIZE;
if (!options)
goto done;
It only sets the above two options by default and before, it also used to
set XFSMNT_IDELETE by default.
If options are specified, then
if (!(args->flags & XFSMNT_DMAPI) && !ikeep)
args->flags |= XFSMNT_IDELETE;
is executed later on which is skipped by the "goto done;" above.
The solution is to invert the logic.
SGI-PV: 977771
SGI-Modid: xfs-linux-melb:xfs-kern:30590a
Signed-off-by: Niv Sardi <xaiki@sgi.com>
Signed-off-by: Barry Naujok <bnaujok@sgi.com>
Signed-off-by: Josef 'Jeff' Sipek <jeffpc@josefsipek.net>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Change -I include directives to find headers in the out-of-tree spot. This
allows a directory containing only xfs files to be built as:
SGI-PV: 971186
SGI-Modid: xfs-linux-melb:xfs-kern:29878a
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Donald Douwsma <donaldd@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Makefile (and Kbuild) would include Makefile-linux-26 I doubt XFS will
really still compile on 2.4; so drop that. This moves Makefile-linux-26
into Makefile and drops Kbuild. Also having wrappers as both Kbuild and
Makefile seemed redundant anyways.
The patch is relatively large because it renames a file, but no functional
changes.
SGI-PV: 971050
SGI-Modid: xfs-linux-melb:xfs-kern:29781a
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Donald Douwsma <donaldd@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
* Add path_put() functions for releasing a reference to the dentry and
vfsmount of a struct path in the right order
* Switch from path_release(nd) to path_put(&nd->path)
* Rename dput_path() to path_put_conditional()
[akpm@linux-foundation.org: fix cifs]
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: <linux-fsdevel@vger.kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Steven French <sfrench@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the central patch of a cleanup series. In most cases there is no good
reason why someone would want to use a dentry for itself. This series reflects
that fact and embeds a struct path into nameidata.
Together with the other patches of this series
- it enforced the correct order of getting/releasing the reference count on
<dentry,vfsmount> pairs
- it prepares the VFS for stacking support since it is essential to have a
struct path in every place where the stack can be traversed
- it reduces the overall code size:
without patch series:
text data bss dec hex filename
5321639 858418 715768 6895825 6938d1 vmlinux
with patch series:
text data bss dec hex filename
5320026 858418 715768 6894212 693284 vmlinux
This patch:
Switch from nd->{dentry,mnt} to nd->path.{dentry,mnt} everywhere.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix cifs]
[akpm@linux-foundation.org: fix smack]
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
remove beX_add functions and replace all uses with beX_add_cpu
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Reviewed-by: Dave Chinner <dgc@sgi.com>
Cc: Timothy Shimmin <tes@sgi.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6: (62 commits)
[XFS] add __init/__exit mark to specific init/cleanup functions
[XFS] Fix oops in xfs_file_readdir()
[XFS] kill xfs_root
[XFS] keep i_nlink updated and use proper accessors
[XFS] stop updating inode->i_blocks
[XFS] Make xfs_ail_check check less by default
[XFS] Move AIL pushing into it's own thread
[XFS] use generic_permission
[XFS] stop re-checking permissions in xfs_swapext
[XFS] clean up xfs_swapext
[XFS] remove permission check from xfs_change_file_space
[XFS] prevent panic during log recovery due to bogus op_hdr length
[XFS] Cleanup various fid related bits:
[XFS] Fix xfs_lowbit64
[XFS] Remove CFORK macros and use code directly in IFORK and DFORK macros.
[XFS] kill superflous buffer locking (2nd attempt)
[XFS] Use kernel-supplied "roundup_pow_of_two" for simplicity
[XFS] Remove the BPCSHIFT and NB* based macros from XFS.
[XFS] Remove bogus assert
[XFS] optimize XFS_IS_REALTIME_INODE w/o realtime config
...
When xfs_file_readdir() exactly fills a buffer, it can move it's index
past the end of the buffer and dereference it even though the result of
the dereference is never used. On some platforms this causes an oops.
SGI-PV: 976923
SGI-Modid: xfs-linux-melb:xfs-kern:30458a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
The only caller (xfs_fs_fill_super) can simplify call igrab on the root
inode.
SGI-PV: 971186
SGI-Modid: xfs-linux-melb:xfs-kern:30393a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
To get the read-only bind mounts in -mm to work correctly with XFS we need
to call the drop_nlink and inc_nlink helpers to monitor the link count.
Add calls to these to xfs_bumplink and xfs_droplink and stop copying over
di_nlink to i_nlink in xfs_validate_fields and vn_revalidate.
SGI-PV: 971186
SGI-Modid: xfs-linux-melb:xfs-kern:30392a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
The VFS doesn't use i_blocks, it's only used by generic_fillattr and the
generic quota code which XFS doesn't use. In XFS there is one use to check
whether we have an inline or out of line sumlink, but we can replace that
with a check of the XFS_IFINLINE inode flag.
SGI-PV: 971186
SGI-Modid: xfs-linux-melb:xfs-kern:30391a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Checking the entire AIL on every insert and remove is prohibitively
expensive - the sustained sequntial create rate on a single disk drops
from about 1800/s to 60/s because of this checking resulting in the
xfslogd becoming cpu bound.
By default on debug builds, only check the next and previous entries in
the list to ensure they are ordered correctly. If you really want, define
XFS_TRANS_DEBUG to use the old behaviour.
SGI-PV: 972759
SGI-Modid: xfs-linux-melb:xfs-kern:30372a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
When many hundreds to thousands of threads all try to do simultaneous
transactions and the log is in a tail-pushing situation (i.e. full), we
can get multiple threads walking the AIL list and contending on the AIL
lock.
The AIL push is, in effect, a simple I/O dispatch algorithm complicated by
the ordering constraints placed on it by the transaction subsystem. It
really does not need multiple threads to push on it - even when only a
single CPU is pushing the AIL, it can push the I/O out far faster that
pretty much any disk subsystem can handle.
So, to avoid contention problems stemming from multiple list walkers, move
the list walk off into another thread and simply provide a "target" to
push to. When a thread requires a push, it sets the target and wakes the
push thread, then goes to sleep waiting for the required amount of space
to become available in the log.
This mechanism should also be a lot fairer under heavy load as the waiters
will queue in arrival order, rather than queuing in "who completed a push
first" order.
Also, by moving the pushing to a separate thread we can do more
effectively overload detection and prevention as we can keep context from
loop iteration to loop iteration. That is, we can push only part of the
list each loop and not have to loop back to the start of the list every
time we run. This should also help by reducing the number of items we try
to lock and/or push items that we cannot move.
Note that this patch is not intended to solve the inefficiencies in the
AIL structure and the associated issues with extremely large list
contents. That needs to be addresses separately; parallel access would
cause problems to any new structure as well, so I'm only aiming to isolate
the structure from unbounded parallelism here.
SGI-PV: 972759
SGI-Modid: xfs-linux-melb:xfs-kern:30371a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Now that all direct caller of xfs_iaccess are gone we can kill xfs_iaccess
and xfs_access and just use generic_permission with a check_acl callback.
This is required for the per-mount read-only patchset in -mm to work
properly with XFS.
SGI-PV: 971186
SGI-Modid: xfs-linux-melb:xfs-kern:30370a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
xfs_swapext should simplify check if we have a writeable file descriptor
instead of re-checking the permissions using xfs_iaccess. Add an
additional check to refuse O_APPEND file descriptors because swapext is
not an append-only write operation.
SGI-PV: 971186
SGI-Modid: xfs-linux-melb:xfs-kern:30369a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Both callers of xfs_change_file_space alreaedy do the file->f_mode &
FMODE_WRITE check to ensure we have a file descriptor that has been opened
for write mode, so there is no need to re-check that with xfs_iaccess.
Especially as the later might wrongly deny it for corner cases like file
descriptor passing through unix domain sockets.
SGI-PV: 971186
SGI-Modid: xfs-linux-melb:xfs-kern:30365a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
A problem was reported where a system panicked in log recovery due to a
corrupt log record. The cause of the corruption is not known but this
change will at least prevent a crash for this specific scenario. Log
recovery definitely needs some more work in this area.
SGI-PV: 974151
SGI-Modid: xfs-linux-melb:xfs-kern:30318a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
- merge xfs_fid2 into it's only caller xfs_dm_inode_to_fh.
- remove xfs_vget and opencode it in the two callers, simplifying
both of them by avoiding the awkward calling convetion.
- assign directly to the dm_fid_t members in various places in the
dmapi code instead of casting them to xfs_fid_t first (which
is identical to dm_fid_t)
SGI-PV: 974747
SGI-Modid: xfs-linux-melb:xfs-kern:30258a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Vlad Apostolov <vapo@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
xfs_lowbit64 was broken on 32 bit platforms in a recent cleanup of the xfs
bitops. Fix it back up again.
SGI-PV: 974005
SGI-Modid: xfs-linux-melb:xfs-kern:30202a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Currently XFS_IFORK_* and XFS_DFORK* are implemented by means of
XFS_CFORK* macros. But given that XFS_IFORK_* operates on an xfs_inode
that embedds and xfs_icdinode_core and XFS_DFORK_* operates on an
xfs_dinode that embedds a xfs_dinode_core one will have to do endian
swapping while the other doesn't. Instead of having the current mess with
the CFORK macros that have byteswapping and non-byteswapping version
(which are inconsistantly named while we're at it) just define each family
of the macros to stand by itself and simplify the whole matter.
A few direct references to the CFORK variants were cleaned up to use IFORK
or DFORK to make this possible.
SGI-PV: 971186
SGI-Modid: xfs-linux-melb:xfs-kern:30163a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
There is no need to lock any page in xfs_buf.c because we operate on our
own address_space and all locking is covered by the buffer semaphore. If
we ever switch back to main blockdeive address_space as suggested e.g. for
fsblock with a similar scheme the locking will have to be totally revised
anyway because the current scheme is neither correct nor coherent with
itself.
SGI-PV: 971186
SGI-Modid: xfs-linux-melb:xfs-kern:30156a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
SGI-PV: 971186
SGI-Modid: xfs-linux-melb:xfs-kern:30098a
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
The BPCSHIFT based macros, btoc*, ctob*, offtoc* and ctooff are either not
used or don't need to be used. The NDPP, NDPP, NBBY macros don't need to
be used but instead are replaced directly by PAGE_SIZE and PAGE_CACHE_SIZE
where appropriate. Initial patch and motivation from Nicolas Kaiser.
SGI-PV: 971186
SGI-Modid: xfs-linux-melb:xfs-kern:30096a
Signed-off-by: Tim Shimmin <tes@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
This assert is bogus. We can have a forced shutdown occur
between the check for the XLOG_FORCED_SHUTDOWN and the ASSERT. Also, the
logging system shouldn't care about the state of XFS_FORCED_SHUTDOWN, it
should only check XLOG_FORCED_SHUTDOWN. The logging system has it's own
forced shutdown flag so, for the case of a forced shutdown that's not due
to a logging error, we can flush the log.
SGI-PV: 972985
SGI-Modid: xfs-linux-melb:xfs-kern:30029a
Signed-off-by: Niv Sardi <xaiki@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Use XFS_IS_REALTIME_INODE in more places, and #define it to 0 if
CONFIG_XFS_RT is off. This should be safe because mount checks in
xfs_rtmount_init:
so if we get mounted w/o CONFIG_XFS_RT, no realtime inodes should be
encountered after that.
Defining XFS_IS_REALTIME_INODE to 0 saves a bit of stack space,
presumeably gcc can optimize around the various "if (0)" type checks:
xfs_alloc_file_space -8 xfs_bmap_adjacent -16 xfs_bmapi -8
xfs_bmap_rtalloc -16 xfs_bunmapi -28 xfs_free_file_space -64 xfs_imap +8
<-- ? hmm. xfs_iomap_write_direct -12 xfs_qm_dqusage_adjust -4
xfs_qm_vop_chown_reserve -4
SGI-PV: 971186
SGI-Modid: xfs-linux-melb:xfs-kern:30014a
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Mount option parsing is platform specific. Move it out of core code into
the platform specific superblock operation file.
SGI-PV: 971186
SGI-Modid: xfs-linux-melb:xfs-kern:30012a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Implement the new generic callout for file preallocation. Atomically
change the file size if requested.
SGI-PV: 972756
SGI-Modid: xfs-linux-melb:xfs-kern:30009a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
The log force added in xfs_iget_core() has been a performance issue since
it was introduced for tight loops that allocate then unlink a single file.
under heavy writeback, this can introduce unnecessary latency due tothe
log I/o getting stuck behind bulk data writes.
Fix this latency problem by avoinding the need for the log force by moving
the place we mark linux inode dirty to the transaction commit rather than
on transaction completion.
This also closes a potential hole in the sync code where a linux inode is
not dirty between the time it is modified and the time the log buffer has
been written to disk.
SGI-PV: 972753
SGI-Modid: xfs-linux-melb:xfs-kern:30007a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Prevent transaction overrun in xfs_iomap_write_allocate() if we race with
a truncate that overlaps the delalloc range we were planning to allocate.
If we race, we may allocate into a hole and that requires block
allocation. At this point in time we don't have a reservation for block
allocation (apart from metadata blocks) and so allocating into a hole
rather than a delalloc region results in overflowing the transaction block
reservation.
Fix it by only allowing a single extent to be allocated at a time.
SGI-PV: 972757
SGI-Modid: xfs-linux-melb:xfs-kern:30005a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
There are several mount options that don't show up in /proc/mounts. Add
them in and clean up the showargs code at the same time.
SGI-PV: 971186
SGI-Modid: xfs-linux-melb:xfs-kern:30004a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Sparse trips over the locking order in xlog_recover_do_efd_trans() when
xfs_trans_delete_ail() drops the ail lock. Because the unlock is
conditional, we need to either annotate with a "fake unlock" or change the
structure of the code so sparse thinks the function always unlocks.
Reordering the code makes it simpler, so do that.
SGI-PV: 972755
SGI-Modid: xfs-linux-melb:xfs-kern:30003a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
These are mostly locking annotations, marking things static, casts where
needed and declaring stuff in header files.
SGI-PV: 971186
SGI-Modid: xfs-linux-melb:xfs-kern:30002a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
We need xfs_bulkstat() to report inode stat for inodes with link count
zero but reference count non zero.
The fix here:
http://oss.sgi.com/archives/xfs/2007-09/msg00266.html
changed this behavior and made xfs_bulkstat() to filter all unlinked
inodes including those that are not destroyed yet but held by reference.
The attached patch returns back to the original behavior by marking the
on-disk inode buffer "dirty" when di_mode is cleared (at that time both
inode link and reference counter are zero).
SGI-PV: 972004
SGI-Modid: xfs-linux-melb:xfs-kern:29914a
Signed-off-by: Vlad Apostolov <vapo@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
XFS_IOC_GETVERSION, XFS_IOC_GETXFLAGS and XFS_IOC_SETXFLAGS all take a
"long" which changes size between 32 and 64 bit platforms.
So, the ioctl cmds that come in from a 32-bit app aren't as expected, for
example on GETXFLAGS,
unknown cmd fd(3) cmd(80046601){t:'f';sz:4}
due to the size mismatch.
So, use instead the 32-bit version of the commands for compat ioctls, and
other than that it doesn't take any more manipulation.
Also, for both native and compat versions, just define them to the values
as defined in fs.h
SGI-PV: 971186
SGI-Modid: xfs-linux-melb:xfs-kern:29849a
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
No need for xfs to have its own hex dumping routine now that the kernel
has one.
SGI-PV: 971186
SGI-Modid: xfs-linux-melb:xfs-kern:29847a
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
This macro is unused an all other acros in this family operate on native
types, so we most likely won't grow a user either.
SGI-PV: 971186
SGI-Modid: xfs-linux-melb:xfs-kern:29846a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Eric Sandeen