* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
mac80211: fix deauth before assoc
iwlwifi: add missing rcu_read_lock
mac80211: fix function pointer check
wireless: remove my name from the maintainer list
ath5k: fix NULL pointer in antenna configuration
p54usb: Add device ID for Dell WLA3310 USB
wl1251: fix a memory leak in probe
ipmr: dont corrupt lists
8139too: fix buffer overrun in rtl8139_init_board
asix: check packet size against mtu+ETH_HLEN instead of ETH_FRAME_LEN
r8169: fix random mdio_write failures
ip6mr: fix a typo in ip6mr_for_each_table()
iwlwifi: move sysfs_create_group to post request firmware
iwlwifi: add name to Maintainers list
iwl3945: fix internal scan
iwl3945: enable stuck queue detection on 3945
ipv6: avoid high order allocations
ath5k: retain promiscuous setting
ath5k: depend on CONFIG_PM_SLEEP for suspend/resume functions
mac80211: process station blockack action frames from work
...
Using ieee80211_find_sta() needs to be under
RCU read lock, which iwlwifi currently misses,
so fix it.
Cc: stable@kernel.org
Reported-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the channel is not set yet and we configure the antennas just store the
setting. It will be activated during the next reset, when the channel is set.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add Dell WLA3310 USB wireless card, which has a Z-Com XG-705A chipset, to the
USB Ids in p54usb.
Signed-off-by: Jason Dravet <dravet@hotmail.com>
Tested-by: Richard Gregory Tillmore <rtillmore@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Cc: <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1251_sdio_probe() error path is missing wl1251_free_hw, add it.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix rtl_chip_info buffer overrun when we can't identify the chip.
(i = ARRAY_SIZE (rtl_chip_info) in this case)
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver checks received packet is too large in asix_rx_fixup() and fails if it is. Problem is
that MTU might be set larger than 1500 and asix fails to work correctly with VLAN tagged
packets. The check should be 'dev->net->mtu + ETH_HLEN' instead.
Tested with AX88772.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some configurations need delay between the "write completed" indication
and new write to work reliably.
Realtek driver seems to use longer delay when polling the "write complete"
bit, so it waits long enough between writes with high probability (but
could probably break too). This patch adds a new udelay to make sure we
wait unconditionally some time after the write complete indication.
This caused a regression with XID 18000000 boards when the board specific
phy configuration writing many mdio registers was added in commit
2e955856ff (r8169: phy init for the 8169scd). Some of the configration
mdio writes would almost always fail, and depending on failure might leave
the PHY in non-working state.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Acked-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port of internal scan to iwl3945 missed introduction
of iwl3945_get_single_channel_for_scan.
Fix the following bug by introducing the iwl3945_get_single_channel_for_scan
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2208
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (30 commits)
X25: remove duplicated #include
tcp: use correct net ns in cookie_v4_check()
rps: tcp: fix rps_sock_flow_table table updates
ppp_generic: fix multilink fragment sizes
syncookies: remove Kconfig text line about disabled-by-default
ixgbe: only check pfc bits in hang logic if pfc is enabled
net: check for refcount if pop a stacked dst_entry
ixgbe: return IXGBE_ERR_RAR_INDEX when out of range
act_pedit: access skb->data safely
sfc: Store port number in net_device::dev_id
epic100: Test __BIG_ENDIAN instead of (non-existent) CONFIG_BIG_ENDIAN
tehuti: return -EFAULT on copy_to_user errors
isdn/kcapi: return -EFAULT on copy_from_user errors
e1000e: change logical negate to bitwise
sfc: Get port number from CS_PORT_NUM, not PCI function number
cls_u32: use skb_header_pointer() to dereference data safely
TCP: tcp_hybla: Fix integer overflow in slow start increment
act_nat: fix the wrong checksum when addr isn't in old_addr/mask
net/fec: fix pm to survive to suspend/resume
korina: count RX DMA OVR as rx_fifo_error
...
Remove duplicated #include('s) in drivers/net/wan/x25_asy.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix bug in multilink fragment size calculation introduced by
commit 9c705260fe
"ppp: ppp_mp_explode() redesign"
Signed-off-by: Ben McKeegan <ben@netservers.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only check pfc bits in hang logic if PFC is enabled. Previously,
if DCB was enabled but PFC was disabled the incorrect pause
bits would be checked.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 56d1de0a21, "ath5k: clean up
filter flags setting" introduced a regression in monitor mode such
that the promisc filter flag would get lost.
Although we set the promisc flag when it changed, we did not
preserve it across subsequent calls to configure_filter. This patch
restores the original functionality.
Cc: stable@kernel.org
Bisected-by: weedy2887@gmail.com
Tested-by: weedy2887@gmail.com
Tested-by: Rick Farina <sidhayn@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When building a kernel with CONFIG_PM=y but neither suspend nor
hibernate support, the compiler complains about the static functions
ath5k_pci_suspend() and ath5k_pci_resume() not being used:
drivers/net/wireless/ath/ath5k/base.c:713:12: warning: ‘ath5k_pci_suspend’ defined but not used
drivers/net/wireless/ath/ath5k/base.c:722:12: warning: ‘ath5k_pci_resume’ defined but not used
Depending on CONFIG_PM_SLEEP rather than CONFIG_PM fixes the issue.
Signed-off-by: Tobias Doerffel <tobias.doerffel@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/macio: Fix probing of macio devices by using the right of match table
agp/uninorth: Fix oops caused by flushing too much
powerpc/pasemi: Update MAINTAINERS file
powerpc/cell: Fix integer constant warning
powerpc/kprobes: Remove resume_execution() in kprobes
powerpc/macio: Don't dereference pointer before null check
Based on original patch from Shirley Ma <xma@us.ibm.com>
Return IXGBE_ERR_RAR_INDEX when RAR index is out of range, instead of
returning IXGBE_SUCCESS.
CC: Shirley Ma <xma@us.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This exposes the port number to userland through sysfs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Probably no one has used this driver on big-endian systems, since it was
setting up descriptor swapping if CONFIG_BIG_ENDIAN is set, which it
never is, since that symbol is not mentioned anywhere else in the kernel
source. Switch this test to a check for __BIG_ENDIAN so it has a chance
at working.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
copy_to_user() returns the number of bytes remaining but we want to
return a negative error code here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bitwise negate is intended here. With the logical negate the
condition is always false.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A single shared memory region used to communicate with firmware is
mapped into both PCI PFs of the SFC9020 and SFL9021. Drivers must be
able to identify which port they are addressing in order to use the
correct sub-region. Currently we use the PCI function number, but the
PCI address may be virtualised. Use the CS_PORT_NUM register field
defined for just this purpose.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes build error caused by the OF device_node
pointer being moved into struct device
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* in the actual driver, calling fec_stop and fec_enet_init doesn't
allow to have a working network interface at resume (where a
ifconfig down and up is required to recover the interface)
* by using fec_enet_close and fec_enet_open, this patch solves this
problem and handle the case where the link changed between suspend
and resume
* this patch also disable clock at suspend and reenable it at resume
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This way, RX DMA overruns (actually being caused by overrun of the
512byte input FIFO) show up in ifconfig output. The rx_fifo_errors
counter is unused otherwise.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch completes commit 89d71a66c4
which missed this spot, as it seems.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
By calling korina_restart(), the IRQ handler tries to disable the
interrupt it's currently serving. This leads to a deadlock since
disable_irq() waits for any running IRQ handlers to finish before
returning. This patch addresses the issue by turning korina_restart()
into a workqueue task, which is then scheduled when needed.
Reproducing the deadlock is easily done using e.g. GNU netcat to send
large amounts of UDP data to the host running this driver.
Note that the same problem (and fix) applies to TX FIFO underruns, but
apparently these are less easy to trigger.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make get/set netlink VF_PORT truly symmetrical, we need to keep track
of what items are set and only return those items on get. Previously, the
driver wasn't differentiating between a set of attr with a NULL string,
for example, and not setting the attr at all. We only want to return
the NULL string if the attr was actually set with a NULL string. Otherwise,
don't return the attr.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The regression is caused by:
commit 4327ba435a
bnx2: Fix netpoll crash.
If ->open() and ->close() are called multiple times, the same napi structs
will be added to dev->napi_list multiple times, corrupting the dev->napi_list.
This causes free_netdev() to hang during rmmod.
We fix this by calling netif_napi_del() during ->close().
Also, bnx2_init_napi() must not be in the __devinit section since it is
called by ->open().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grant patches added an of mach table to struct device_driver. However,
while he changed the macio device code to use that, he left the match
table pointer in struct macio_driver and didn't update drivers to use
the "new" one, thus breaking the probing.
This completes the change by moving all drivers to setup the "new"
one, removing all traces of the old one, and while at it (since it
changes the exact same locations), I also remove two other duplicates
from struct driver which are the name and owner fields.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We can wake all queues after a chip reset since everything should be set up and
we are ready to transmit. If we don't do that we might end up starting up with
stopped queues, not beeing able to transmit. (This started to happen after
"ath5k: clean up queue manipulation" but since periodic calibration also
stopped and started the queues this effect was hidden most of the time).
This way we can also get rid of the superfluous ath5k_reset_wake() function.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
virtio-net bounces buffer allocations off to
a thread if it can't allocate buffers from the atomic
pool. However, if posting buffers still requires atomic
buffers, this is unlikely to succeed.
Fix by passing in the proper gfp_t parameter.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code fails on ppc as hdr.timeout is not being converted
to le32.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes build error caused by the OF device_node pointer
being moved into struct device.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (47 commits)
mfd: Rename twl5031 sih modules
mfd: Storage class for timberdale should be before const qualifier
mfd: Remove unneeded and dangerous clearing of clientdata
mfd: New AB8500 driver
gpio: Fix inverted rdc321x gpio data out registers
mfd: Change rdc321x resources flags to IORESOURCE_IO
mfd: Move pcf50633 irq related functions to its own file.
mfd: Use threaded irq for pcf50633
mfd: pcf50633-adc: Fix potential race in pcf50633_adc_sync_read
mfd: Fix pcf50633 bitfield logic in interrupt handler
gpio: rdc321x needs to select MFD_CORE
mfd: Use menuconfig for quicker config editing
ARM: AB3550 board configuration and irq for U300
mfd: AB3550 core driver
mfd: AB3100 register access change to abx500 API
mfd: Renamed ab3100.h to abx500.h
gpio: Add TC35892 GPIO driver
mfd: Add Toshiba's TC35892 MFD core
mfd: Delay to mask tsc irq in max8925
mfd: Remove incorrect wm8350 kfree
...
This fixes some sparse warnings:
drivers/net/benet/be_cmds.c:1503:12: warning: function
'be_cmd_enable_magic_wol' with external linkage has definition
drivers/net/benet/be_cmds.c:1668:12: warning: function
'be_cmd_get_seeprom_data' with external linkage has definition
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The unlock accidentally got removed from the error path in dd131e76e5:
"be2net: Bug fix to avoid disabling bottom half during firmware upgrade."
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an occasional transmit lockup in the mac-fcc which
occurs after a tx error. The test scenario had the local port set
to autoneg and the other end fixed at 100FD, resulting in a large
number of late collisions.
According to the MPC8280RM 30.10.1.3 (also 8272RM 29.10.1.3), after
a tx error occurs, TBPTR may sometimes point beyond BDs still marked
as ready. This patch walks back through the BDs and points TBPTR to
the earliest one marked as ready.
Tested on a custom board with a MPC8280.
Signed-off-by: Mark Ware <mware@elphinstone.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes:
drivers/net/wireless/libertas/rx.c: In function process_rxed_802_11_packet:
drivers/net/wireless/libertas/rx.c:354: error: radiotap_hdr.flags may be used uninitialized in this function
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This bug was introduced by the following commit
Author: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Date: Thu Apr 15 17:38:46 2010 -0400
ath9k: Remove ATH9K_TX_SW_ABORTED and introduce a bool for this purpose
Wrong buffer is checked for bf_tx_aborted field in ath_tx_num_badfrms(),
this may result in a rate scaling with wrong feedback (number
of unacked frames in this case). It is the last one in the chain
of buffers for an aggregate frame that should be checked.
Also it misses the initialization of this field in the buffer,
this may lead to a situation where we stop the sw retransmission
of failed subframes associated to this buffer.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Linus Torvalds