Currently, when CONFIG_VIRT_CPU_ACCOUNTING is enabled, we use the
PURR register for measuring the user and system time used by
processes, as well as other related times such as hardirq and
softirq times. This turns out to be quite confusing for users
because it means that a program will often be measured as taking
less time when run on a multi-threaded processor (SMT2 or SMT4 mode)
than it does when run on a single-threaded processor (ST mode), even
though the program takes longer to finish. The discrepancy is
accounted for as stolen time, which is also confusing, particularly
when there are no other partitions running.
This changes the accounting to use the timebase instead, meaning that
the reported user and system times are the actual number of real-time
seconds that the program was executing on the processor thread,
regardless of which SMT mode the processor is in. Thus a program will
generally show greater user and system times when run on a
multi-threaded processor than on a single-threaded processor.
On pSeries systems on POWER5 or later processors, we measure the
stolen time (time when this partition wasn't running) using the
hypervisor dispatch trace log. We check for new entries in the
log on every entry from user mode and on every transition from
kernel process context to soft or hard IRQ context (i.e. when
account_system_vtime() gets called). So that we can correctly
distinguish time stolen from user time and time stolen from system
time, without having to check the log on every exit to user mode,
we store separate timestamps for exit to user mode and entry from
user mode.
On systems that have a SPURR (POWER6 and POWER7), we read the SPURR
in account_system_vtime() (as before), and then apportion the SPURR
ticks since the last time we read it between scaled user time and
scaled system time according to the relative proportions of user
time and system time over the same interval. This avoids having to
read the SPURR on every kernel entry and exit. On systems that have
PURR but not SPURR (i.e., POWER5), we do the same using the PURR
rather than the SPURR.
This disables the DTL user interface in /sys/debug/kernel/powerpc/dtl
for now since it conflicts with the use of the dispatch trace log
by the time accounting code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since the decrementer and timekeeping code was moved over to using
the generic clockevents and timekeeping infrastructure, several
variables and functions have been obsolete and effectively unused.
This deletes them.
In particular, wakeup_decrementer() is no longer needed since the
generic code reprograms the decrementer as part of the process of
resuming the timekeeping code, which happens during sysdev resume.
Thus the wakeup_decrementer calls in the suspend_enter methods for
52xx platforms have been removed. The call in the powermac cpu
frequency change code has been replaced by set_dec(1), which will
cause a timer interrupt as soon as interrupts are enabled, and the
generic code will then reprogram the decrementer with the correct
value.
This also simplifies the generic_suspend_en/disable_irqs functions
and makes them static since they are not referenced outside time.c.
The preempt_enable/disable calls are removed because the generic
code has disabled all but the boot cpu at the point where these
functions are called, so we can't be moved to another cpu.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since we started using the generic timekeeping code, we haven't had a
powerpc-specific version of do_gettimeofday, and hence there is now
nothing that reads the do_gtod variable in arch/powerpc/kernel/time.c.
This therefore removes it and the code that sets it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
from include/asm-powerpc. This is the result of a
mkdir arch/powerpc/include/asm
git mv include/asm-powerpc/* arch/powerpc/include/asm
Followed by a few documentation/comment fixups and a couple of places
where <asm-powepc/...> was being used explicitly. Of the latter only
one was outside the arch code and it is a driver only built for powerpc.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Paul Mackerras