In order to share the common code in tsc.c which does CPU Khz calibration, we
need to make an accurate value of CPU speed available to the tsc.c code. This
value loses a lot of precision in a VM because of the timing differences with
real hardware, but we need it to be as precise as possible so the guest can
make accurate time calculations with the cycle counters.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The custom_sched_clock hook is broken. The result from sched_clock needs to
be in nanoseconds, not in CPU cycles. The TSC is insufficient for this
purpose, because TSC is poorly defined in a virtual environment, and mostly
represents real world time instead of scheduled process time (which can be
interrupted without notice when a virtual machine is descheduled).
To make the scheduler consistent, we must expose a different nature of time,
that is scheduled time. So deprecate this custom_sched_clock hack and turn it
into a paravirt-op, as it should have been all along. This allows the tsc.c
code which converts cycles to nanoseconds to be shared by all paravirt-ops
backends.
It is unfortunate to add a new paravirt-op, but this is a very distinct
abstraction which is clearly different for all virtual machine
implementations, and it gets rid of an ugly indirect function which I
ashamedly admit I hacked in to try to get this to work earlier, and then even
got in the wrong units.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Critical bugfixes for the VMI-Timer code.
1) Do not setup a one shot alarm if we are keeping the periodic alarm
armed. Additionally, since the periodic alarm can be run at a lower rate
than HZ, let's fixup the guard to the no-idle-hz mode appropriately. This
fixes the bug where the no-idle-hz mode might have a higher interrupt rate
than the non-idle case.
2) The interrupt handler can no longer adjust xtime due to nested lock
acquisition. Drop this. We don't need to check for wallclock time at
every tick, it can be done in userspace instead.
3) Add a bypass to disable noidle operation. This is useful as a last
minute workaround, or testing measure.
4) The code to skip the IO_APIC timer testing (no_timer_check) should be
conditional on IO_APIC, not SMP, since UP kernels can have this configured
in as well.
Signed-off-by: Dan Hecht <dhecht@vmware.com>
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most drivers using GPIOs already know they are running on a system that
supports the generic GPIO calls, because of other platform dependencies.
But the generic GPIO-based LED and input button drivers can't know that.
So this patch adds a Kconfig hook, GENERIC_GPIO, to mark the platforms
where <asm/gpio.h> will do the right thing. Currently that's a bunch of
ARMs, and AVR32; more are on the way.
It also fixes a dependency bug for the gpio button input driver; it was
wrong to start with, now it covers all platforms with GENERIC_GPIO.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: <raph@8d.com>
Cc: <msvoboda@ra.rockwell.com>
Cc: pHilipp Zabel <philipp.zabel@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In some cases when we are not using msi we need a way to ensure that the
hardware does not have an msi capability enabled. Currently the code has been
calling disable_msi_mode to try and achieve that. However disable_msi_mode
has several other side effects and is only available when msi support is
compiled in so it isn't really appropriate.
Instead this patch implements pci_msi_off which disables all msi and msix
capabilities unconditionally with no additional side effects.
pci_disable_device was redundantly clearing the bus master enable flag and
clearing the msi enable bit. A device that is not allowed to perform bus
mastering operations cannot generate intx or msi interrupt messages as those
are essentially a special case of dma, and require bus mastering. So the call
in pci_disable_device to disable msi capabilities was redundant.
quirk_pcie_pxh also called disable_msi_mode and is updated to use pci_msi_off.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/home/rmk/linux-2.6-arm: (30 commits)
[ARM] Acorn: move the i2c bus driver into drivers/i2c
[ARM] ARM SCSI: Don't try to dma_map_sg too many scatterlist entries
[ARM] ARM FAS216: don't modify scsi_cmnd request_bufflen
[ARM] rtc-pcf8583: Final fixes for this RTC on RiscPC
[ARM] rtc-pcf8583: correct month and year offsets
[ARM] rtc-pcf8583: don't use BCD_TO_BIN/BIN_TO_BCD
[ARM] EBSA110: Work around build errors
[ARM] 4241/1: Define mb() as compiler barrier on a uniprocessor system
[ARM] 4239/1: S3C24XX: Update kconfig entries for PM
[ARM] 4238/1: S3C24XX: docs: update suspend and resume
[ARM] 4237/2: oprofile: Always allow backtraces on ARM
[ARM] Yet more asm/apm-emulation.h stuff
ARM: OMAP: Add missing get_irqnr_preamble and arch_ret_to_user for omap2
ARM: OMAP: Use linux/delay.h not asm/delay.h
ARM: OMAP: Remove obsolete alsa typedefs
ARM: OMAP: omap1510->15xx conversions needed for sx1
ARM: OMAP: Add missing includes to board-nokia770
ARM: OMAP: Workqueue changes for board-h4.c
ARM: OMAP: dmtimer.c omap1 register fix
ARM: OMAP: board-nokia770: correct lcd name
...
Adds cardbus ressources for MTX1 boards which have a PCMCIA controller.
Signed-off-by: Florian Fainelli <florian.fainelli@int-evry.fr>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch has removed unused timer resource.
Moreover, the name of reserved resources ware changed.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If R4k counter was used for hpt_timer and interrupt source,
c0_hpt_timer_init() initializes the c0_compare register.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The generic rtc-ds1742 driver can be used for RBTX4927 and JMR3927
(with __swizzle_addr trick). This patch also removes MIPS local
DS1742 stuff.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Work around EBSA110 build errors by selecting NO_IOPORT. EBSA110
can't support an IO port to MMIO mapping mechanism because the
MMIO and IO port spaces have quite different and complex addressing
requirements.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The information contained within platform_data should be self-contained.
Replace the pointer to a MAC address with the actual MAC address in
struct mv643xx_eth_platform_data.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
No need to stop tc35815 before resetting the board. This fixes the
build of tc35815 as a module. This also means there is no caller of
tc35815_killall left, so remove that function also.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We mistakedly modify 'bus' in the innermost loop. What
should happen is that at each register index iteration,
we start with the same 'bus'.
So preserve it's value at the top level, and use a loop
local variable 'dbus' for iteration.
This bug causes registers other than the first to be
decoded improperly.
Signed-off-by: David S. Miller <davem@davemloft.net>
Update help text with location of documentation
and duplicate the note on the speed of CRC
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Always allow backtrace when using oprofile on ARM, even if a PMU
isn't present.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert 1510->15xx in generic omap code, so that sx1 can work.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add missing includes to board-nokia770 to make it
compile again.
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When I went to use dmtimer7 it did not seem to work. I noticed that
the base addresses for dmtimers 7 and 8 were set wrong. A simple patch
to correct a small error. Confirmed to fix the problem on an OSK.
Signed-off-by: Matthew Percival <matthew@capgo.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some time ago, the 'lcd_lph8923' device was renamed to 'lcd_mipid' but
the board-nokia770.c file was not updated accordingly, leading to not
working lcd.
This one-liner fixe the trouble.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Teach OMAP2 gp timer that HZ isn't always 100.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix warning
arch/arm/mach-omap1/pm.c: In function 'omap_pm_init':
arch/arm/mach-omap1/pm.c:765: warning: ignoring return value
of 'subsys_create_file', declared with attribute
warn_unused_result
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix warning
arch/arm/mach-omap2/timer-gp.c: In function
'omap2_gp_timer_init':
arch/arm/mach-omap2/timer-gp.c:70: warning: implicit
declaration of function 'setup_irq'
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix warnings
arch/arm/plat-omap/dmtimer.c: In function
'omap_dm_timer_modify_idlect_mask':
arch/arm/plat-omap/dmtimer.c:317: warning: no return
statement in function returning non-void
arch/arm/plat-omap/mailbox.c: In function 'omap_mbox_init':
arch/arm/plat-omap/mailbox.c:231: warning: ignoring return
value of 'class_device_create_file', declared with attribute
warn_unused_result
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
No IRQF_TRIGGER set_type function for IRQ 353 (MPUIO)
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This makes serial usable also on omap310, not only 1510.
(changing 1510->15xx)
Signed-off-by: Marek Vašut <marek.vasut@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The register bits are reset by writing one. Remove the unneeded reads and
fix writes to not clear too many bits.
Signed-off-by: Timo Teras <timo.teras@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix warning:
arch/arm/mach-omap1/clock.c: In function
'omap1_clk_enable_generic':
arch/arm/mach-omap1/clock.c:499: warning: 'return' with no
value, in function returning non-void
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Disable accesses to SOFT_REQ_REG2 and ULPD_SOFT_DISABLE_REQ_REG
registers for 15xx processors that don't have these registers. Enable
level 2 interrupt handler for processors that identify as OMAP 15xx
(e.g 310) and not 1510 specifically. Also fix the following compiler
warning (only visible with CONFIG_OMAP_RESET_CLOCKS):
arch/arm/mach-omap1/clock.c: In function 'omap1_clk_disable_unused':
arch/arm/mach-omap1/clock.c:634: warning: 'return' with a value, in
function returning void
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When it goes to free1_out, dev->dma_mem has not been freed.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3: Introduce CONFIG_PS3_ADVANCED, as suggested by Roman Zippel, and use
it to control questions about PS3 subsystems that may not be obvious for
the casual user.
This gets rid of the following warning on non-powerpc platforms: |
drivers/video/Kconfig:1604:warning: 'select' used by config symbol 'FB_PS3'
refer to undefined symbol 'PS3_PS3AV'
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Zachary Amsden