IRQ diag test was getting executed only when both register test
and link test passed. The test should get executed if ETH_TEST_FL_OFFLINE
flag is set.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When interface is down, create temporary context to config LED.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Loopback mode can not be supported in CNA mode. Removing it until FW is fixed.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Log LRO off message while disabling rx checksum only when
LRO is already enabled.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If eswitch is enabled, rcv ring size can be reduce, as
physical port is partition-ed.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added statistics for Nic Partition supported adapter.
These statistics are maintined in device.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch just rename all P3 #define to P3P.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LRO was not getting enable after interface down/up.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put device in quiescent mode during internal loopback test.
Before running test, set state to NEED_QUISCENT. After getting
ack from all function, change state to QUISCENT and perform test.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
regs_buff[i] and diag_registers[j] array should use different index
variable.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Loop 10 times with delay of 1 ms to rcv packet.
o Print garbage packet.
o Try send/receive MAX(16) packet, instead of exit from test,
if a packet is not received.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o ethtool reg version bumped to 2
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change QLCNIC_CRB_DEV_REF_COUNT to QLCNIC_CRB_DRV_ACTIVE to match
document.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device is not capable of enabling/disabling offload setting per
port in case of Nic Partition.So offload settings needs to be
enabled/disabled per eswitch and it will affect all the function
on that eswitch.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Also dont allow lro to be turn on, if rx csum is disabled
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Give sufficient time for all makes of PHY modules
to establish the link after loopback test.
o Perform online test before offline test.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Loopback not supported for virtual function.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turning off rx pause param and autoneg param is not supported so
return error in that case.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver checks TSO capability from FW before enabling it.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The documented error code for attempts to set unsupported flags (or
to clear flags that cannot be disabled) is EINVAL, not EOPNOTSUPP.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we were allocating device resources during probe and
release them during remove.
Now alloc during interface up and release in interface down.
This helps in device performance, as it doesn't need to keep
track of inactive resources.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to maintian separate state for alloced and freed skb.
This can be done by null check.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following changes have been added to enable the adapter to work in
NIC partitioning mode where multiple PCI functions of an adapter port can
be configured to work as NIC functions. The first function that is enumerated on
the PCI bus assumes the role of management function which, besides being able
to do all the NIC functionality, can configure other NIC partitions. Other NIC
functions can be configured as privileged or non privileged functions.
Privileged function can not configure other NIC functions but can do all the
NIC functionality including any firmware initialization, chip reset etc. Non
privileged functions can do only basic IO. For chip reset etc, it depends on the
privilege or management function.
1. Added code to determine PCI function number independent of kernel API.
2. Added Driver - FW version 2.0 support.
3. Changed producer and consumer register offset calculation.
4. Added management and privileged operation modes for npar functions. A module
parameter has been added to control it.
5. Added support for configuring the eswitch in the adapter.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LRO ring, cut-thru mode and specific fw version are not
valid to Qlogic CNA device.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MSI_MODE, CAPABILITIES_FW and SCRATCHPAD registers are obsolete.
Driver should not use them.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added additional driver statistics to track errors in rcv/tx path.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add debug print in driver, can be tuned by ethtool msg level
callback.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Statistics added for lro/lso bytes, count for tx stop queue and
wake queue and skb alloc failure count.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kernel default tx csum function (ethtool_op_get_tx_csum) doesn't show
correct csum status. It takes various FLAGS (NETIF_F_ALL_CSUM) in account
to show tx csum status, which driver doesn't set while disabling tx csum.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Loopback test (offline) added in ethtool self test.
o Set device in loopback mode
o Send packets
o Process receive packets in qlcnic_process_rcv_ring_diag()
o Compare packets
o Reset device in normal mode.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interrupt test (offline) added in ethtool self test.
Register a temporary interrupt handler and then send command to fw
to raise an interrupt.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support of device identification by blinking LED for specified time.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o context resources can be in used, while resoruce cleanup is in progress,
during fw recover.
o Null pointer execption can occur in send_cmd_desc, if fw recovery
module frees tx ring without rtnl lock.
o Same applies to ethtool register dump and FW health registers should be dump
in any case.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o 1G/10G Ethernet Driver for Qlgic QLE8240 and QLE8242 CNA devices.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sony Chacko