o Updating module parameter after driver load is not supported
except auto_fw_reset parameter. Changing these parameter after
driver load, can have weird result.
o Update driver version to 5.0.15.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQ diag test was getting executed only when both register test
and link test passed. The test should get executed if ETH_TEST_FL_OFFLINE
flag is set.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver is reading flash fw version from defined address, this address
may be invalid. Indeed Driver should read address for fw version through
flash layout table. Flash layout table has defined region and address for
fw version address should be read from fw image region.
Driver has check for old firmware, this bug can cause driver load fail.
This patch will try to read fw version from flash image region, if that fails,
read from defined address.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.
Signed-off-by: Joe Perches <joe@perches.com>
Some boot code drivers dont have cleanup routine, so pci function
remains in unknown state prior to driver load. So during driver load
issue FLR unconditionally.
Update driver version to 5.0.14.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OCM window register offset was calculated incorrectly for
pci function greater than zero.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When interface is down, create temporary context to config LED.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently driver set default eswitch configuration values for PF function,
instead of validating values sent by application.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Loopback mode can not be supported in CNA mode. Removing it until FW is fixed.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In kdump environment do not depend upon reset_devices parameter
to reset the pci function as this parameter may become obsolete.
Instead use an adapter specific mechanism to determine if the pci
function needs to be reset.
Per function refcount is maintained in driver, which is set in probe
and reset in remove handler of adapter. If the probe detects the count
as non zero then reset the function.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use vzalloc() and vzalloc_node() in net drivers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Log LRO off message while disabling rx checksum only when
LRO is already enabled.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add description for CN1000Q adapter
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of kdump environment the function may be in unknown state.
Reset the function using PCI FLR before initializing it.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow minimum bandwidth to be set zero
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Its now illegal to call netif_stop_queue() before register_netdev()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
4095 vlan id is reserved and should not be use.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If eswitch is enabled, rcv ring size can be reduce, as
physical port is partition-ed.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In failover bonding case, same mac address can be programmed on other slave function.
Fw will delete old entry (original func) associated with that mac address.
Need to reporgram mac address, if failover again happen to original function.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN_GROUP_ARRAY_LEN is simply the number of possible vlan VIDs.
Since vlan groups will soon be more of an implementation detail
for vlan devices, rename the constant to be descriptive of its
actual purpose.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added statistics for Nic Partition supported adapter.
These statistics are maintined in device.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch just rename all P3 #define to P3P.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Allow promiscous mode setting for VF's depending upon the configuration.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove "Flex-10" from board description.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LRO was not getting enable after interface down/up.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put device in quiescent mode during internal loopback test.
Before running test, set state to NEED_QUISCENT. After getting
ack from all function, change state to QUISCENT and perform test.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently fw recovery usage global workqueue.
As same workqueue used by kernel for ethtool and etc., supporting
quiescent mode is not possible, without driver private workqueue.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver has several pieces of dead code (found by running
make namespacecheck). This patch removes them.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting mtu < 68 is not supported.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port mode setting is not required for Qlogic CNA adapters.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o desc->vlan_tci is in __le16 format. Doing htons and
cpu_to_le64 again on vlan_tci, result in invalid value on ppc.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipaddress in ifa->ifa_address field are in big endian format.
Also device requires ip address in big endian only.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
regs_buff[i] and diag_registers[j] array should use different index
variable.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the counters are not implemented in fw.
Fw return NOT AVAILABLE VALUE as (0xffffffffffffffff).
Adding these counters, result in invalid value.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Loop 10 times with delay of 1 ms to rcv packet.
o Print garbage packet.
o Try send/receive MAX(16) packet, instead of exit from test,
if a packet is not received.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change "return (EXPR);" to "return EXPR;"
return is not a function, parentheses are not required.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->truesize is set in core network.
Dont change it unless dealing with fragments.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->truesize is set in core network.
Dont change it unless dealing with fragments.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qlcnic driver allocates rx skbs and gives to hardware too bytes of extra
storage, allowing for corruption of kernel data.
NET_IP_ALIGN being 0 on some platforms (including x86), drivers should
not assume it's 2.
rds_ring->skb_size = rds_ring->dma_size + NET_IP_ALIGN;
...
skb = dev_alloc_skb(rds_ring->skb_size);
skb_reserve(skb, 2);
pci_map_single(pdev, skb->data, rds_ring->dma_size, PCI_DMA_FROMDEVICE);
(and rds_ring->skb_size == rds_ring->dma_size) -> bug
Because of extra alignment (1500 + 32) -> four extra bytes are available
before the struct skb_shared_info, so corruption is not noticed.
Note: this driver could use netdev_alloc_skb_ip_align()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't compare flash and file fw version. Allow to load
old fw from file than flashed fw.
If file fw is present, don't skip fw re-intialization.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LRO + GRO + vlan rx accleration support, performance increases
around 20% and cpu utilization reduces around 70% on vlan interface.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRO support + vlan rx accleration, boost around 9%
performance and reduces 25% of cpu utilization on vlan
interface.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
amit salecha