Get rid of old users of of_platform_driver in arch/sparc. Most
of_platform_driver users can be converted to use the platform_bus
directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The device table is required to load modules based on modaliases.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The device table is required to load modules based on modaliases.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The interface is identical EMC6D102, so all that needs to be added are
some definitions and their uses.
Registers apparently missing in EMC6D103S/EMC6D103:A2 compared to EMC6D103:A0,
EMC6D103:A1, and EMC6D102 (according to the data sheets), but used
unconditionally in the driver: 62[5:7], 6D[0:7], and 6E[0:7]. For that
reason, EMC6D103S chips don't get enabled for the time being.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
(Guenter Roeck: Replaced EMC6D103_A2 with EMC6D103S per EMC6D103S datasheet)
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@kernel.org
Add the PCI ID to support the internal temperature sensor of the
AMD "Llano" and "Brazos" processor families.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@kernel.org # ca86828: x86, AMD, PCI: Add AMD northbridge PCI device
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
On systems where the temperature sensor is actually used, the BIOS is
likely to have locked the alarm registers. In that case, all writes
through the corresponding sysfs files would be silently ignored.
To prevent this, detect the locks and make the affected sysfs files
read-only.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The documentation lists standard numbers and chip names in excruciating
detail, but that's all it does. To help mere mortals in deciding
whether to enable this driver, mention what this sensor is for and in
which systems it might be found.
Also add a link to the actual JC 42.4 specification.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
In set_temp_crit_hyst(), make the variable 'val' have the correct
type for strict_strtoul().
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
I2C address range included 0x2a, which the chips do not support.
Replace with 0x29 which is supported but was missing.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
LM64 has 16 degrees Celsius temperature offset on all
remote sensor registers.
This was not considered When LM64 support was added to lm63.c.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@kernel.org
Turn down the no IRQ message - on some platforms that's a normal state of
affairs.
Signed-off-by: Kalhan Trisal <kalhan.trisal@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
ASUS Sabertooth X58 has a bug in ACPI that prevents the reading of MCH
temperature when the "old" ATK0110 interface is used. Add a DMI entry
to override the detection heuristic and force the use of the "new"
interface on this board.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Tested-by: Joris Creyghton <jorisctn@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The switch to dynamically allocated sysfs attributes left the
internal lockdep members uninitialized, causing a formal bug.
This patch adds sysfs_attr_init() to the node creation function,
remedying the problem.
Reported-and-tested-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch adds basic support for LM94 to the LM93 driver. LM94 specific
sensors and features are not supported.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Minor cleanups. Mostly removing assignments in if statements to get
rid of checkpatch errors.
Signed-off-by: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the 1.5V voltage monitoring input (in7) of the
SMSC SCH5127 chip.
Signed-off-by: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
EMC1423 uses the similar register and adds a hardware shutdown pin to
protect exceed temperature. This function is set by resistor; it's not
necessary to do anything in the driver except add the emc1423 pid of 0x23.
Signed-off-by: Jekyll Lai <jekyll_lai@wistron.com>
[Updated Kconfig/comments and minor further changes asked for by the hwmon
maintainers]
Signed-off-by: Alan Cox <alan@linux.intel.com>
[Fixed checkpatch warning]
Signed-of--by: Jean Delvare <khali@linux-fr.org>
This is the same case as fschmd, from which the code was copied as far
as I can see. So the same clean-up applies:
The WDIOC_GETSUPPORT ioctl only needs a mutex because it operates on a
static variable. There is no good reason to keep this variable static,
so let's just make it non-static and drop the now useless mutex
altogether.
See the discussion at:
http://marc.info/?l=lm-sensors&m=125563869402323&w=2
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
As discussed one year ago, the WDIOC_GETSUPPORT ioctl only needs a
mutex because it operates on a static variable. There is no good
reason to keep this variable static, so let's just make it non-static
and drop the now useless mutex altogether.
See the discussion at:
http://marc.info/?l=lm-sensors&m=125563869402323&w=2
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
[JD: Also convert debug messages]
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We have a standard intrusion detection interface now, drivers should
implement it. I've left the old interface in place for the time being,
with a deprecation warning, it will be removed later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
We have a standard intrusion detection interface now, drivers should
implement it. I've left the old interface in place for the time being,
with a deprecation warning, it will be removed later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
We have a standard intrusion detection interface now, drivers should
implement it. I've left the old interface in place for the time being,
with a deprecation warning, it will be removed later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Functions set_fan_min() and set_fan_div() assume that the fan_div
values have already been read from the register. The driver currently
doesn't initialize them at load time, they are only set when function
via686a_update_device() is called. This means that set_fan_min() and
set_fan_div() misbehave if, for example, "sensors -s" is called
before any monitoring application (e.g. "sensors") is has been run.
Fix the problem by always initializing the fan_div values at device
bind time.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The code triggers a false warning with older versions of gcc:
w83795.c: In function 'w83795_update_device':
w83795.c:475: warning: 'lsb' may be used uninitialized in this function
I admit that the code is a little tricky, but I see no way to write it
differently without hurting performance. So let's just silent the
warning with a needless initialization.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Trivial patch updating my email contact details due to change of
employer, and because I no longer have access to the previously used
domain.
Unfortunately I also no longer have access to any ads7828 hardware, but
am happy to support/maintain the driver if others are able to test
changes.
Signed-off-by: Steve Hardy <shardy@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Driver for Dallas Semiconductor DS620 temperature sensor and thermostat
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch fixes all checkpatch errors and most of the checkpatch warnings.
It also fixes the range check in applesmc_store_fan_speed().
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
With the preceding patches, git blame assigns about half of
the file to the present author. Add a line to the copyright
to reflect this.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Make the driver report a single line on success.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Given the dynamic node construction method, the setup of the
accelerometer, light sensor and keyboard backlight sysfs nodes
can be simplified. This patch does not contain any logic changes.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
With the dynamic temperature group in place, the setup of fans
can be simplified. This patch sets up the fans dynamically, removing
a hundred lines of code.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
With temperature keys being determined automatically, the dmi match
data is only used to assign features that can easily be detected from
the smc. This patch removes the dmi match data altogether, and reduces
the match table to the main machine models.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The recent Macbooks have temperature registers of a new type.
This patch adds the logic to handle them.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The current driver creates temperature files based on a list
of temperature keys given per device. Apart from slow adaption
to new machine models, the number of sensors also depends on
the number of processors. This patch looks up the temperature
keys dynamically, thereby supporting all models.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
One main problem with the current driver is the inability to quickly
search for supported keys, resulting in detailed feature maps per
machine model which are cumbersome to maintain.
This patch adds a register lookup table, which enables binary search
for supported keys. The lookup also reduces the io frequency, so the
original mutex is replaced by locks around the actual io.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
[guenter.roeck@ericsson.com: Added value range check to key_at_index_store()]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The device init is used to reset the accelerometer. Failure to reset
is not severe enough to stop loading the module or to resume from
hibernation. This patch relaxes failure to a warning and drops
output in case of success.
Cc: stable@kernel.org
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch add support for the MacBookAir3,1 and MacBookAir3,2 to the
applesmc driver.
[rydberg@euromail.se: minor cleanup]
Cc: stable@kernel.org
Signed-off-by: Edgar Hucek <gimli@dark-green.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Added a few static strings to standardize logging messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Added a few static strings to standardize logging messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The owner field was removed from struct attribute in
6fd69dc578, so don't assign it anymore.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The ltc4215 driver used the chip's "power good" status bit to provide
the power1_alarm file. This is wrong: the chip is really reporting the
status of one of the monitored voltages.
Change the sysfs file from power1_alarm to in2_min_alarm instead. This
matches the voltage that the chip is raising an alarm for.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Allow 1 as a valid div value as specified in the ADM1026 datasheet.
Signed-off-by: Gabriele Gorla <gorlik@penguintown.net>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Prevent setting fan_div from stomping on other fans that share the
same I2C register.
Signed-off-by: Gabriele Gorla <gorlik@penguintown.net>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The manual fan speed control logic of the IT8721F is much different
from what older devices had. Update the code to properly support that.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
This commit fixes the following compile warnings.
From v2.6.37-rc2/m68k/m68k-allmodconfig, v2.6.37-rc2/powerpc/powerpc-randconfig:
drivers/hwmon/lis3lv02d_i2c.c:222: warning: 'lis3_i2c_runtime_suspend' defined but not used
drivers/hwmon/lis3lv02d_i2c.c:231: warning: 'lis3_i2c_runtime_resume' defined but not used
Seen if CONFIG_PM_RUNTIME is not set.
From v2.6.37-rc2/sh4/sh-allyesconfig:
drivers/hwmon/lis3lv02d_i2c.c:191: warning: 'lis3lv02d_i2c_suspend' defined but not used
drivers/hwmon/lis3lv02d_i2c.c:201: warning: 'lis3lv02d_i2c_resume' defined but not used
Seen if CONFIG_PM is set but CONFIG_PM_SLEEP is not.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
This patch fixes the following compile warning.
drivers/hwmon/i5k_amb.c:500: warning: 'i5k_amb_ids' defined but not used
The warning is seen if the driver is built into the kernel (not as module).
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
On the W83795ADG, there's a single pin for BEEP and OVT#, so you
can't have both. Check the configuration and don't create beep
attributes when BEEP pin is not available.
The W83795G has a dedicated BEEP pin so the functionality is always
available there.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
When asked to clear the intrusion alarm, do so immediately. We have to
invalidate the cache to make sure the new status will be read. But we
also have to read from the status register once to clear the pending
alarm, as writing to CLR_CHS surprising won't clear it automatically.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
We can't read the intrusion state from the real-time alarm registers
as we do for all other alarm flags, because real-time alarm bits don't
stick (by definition) and the intrusion state has to stick until
explicitly cleared (otherwise it has little value.)
So we have to use the interrupt status register instead, which is read
from the same address but with a configuration bit flipped in another
register.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Don't expose raw register values to user-space. Decode and encode
temperature channels selected as temperature sources as needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Temperature sources are not correlated directly with temperature
channels. A look-up table is required to find out which temperature
sources can be used depending on which temperature channels (both
analog and digital) are enabled.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Expose fan control method (DC vs. PWM) using the standard sysfs
attributes. I've made it read-only as the board should be wired for
a given mode, the BIOS should have set up the chip for this mode, and
you shouldn't have to change it. But it would be easy enough to make
it changeable if someone comes up with a use case.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
There were two bugs:
* Speed cruise mode was improperly reported for all fans but fan1.
* Fan control method (PWM vs. DC) was mixed with the control mode.
It will be added back as a separate attribute, as per the standard
sysfs interface.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
This clears the following build-time warnings I was seeing:
drivers/hwmon/lm95241.c: In function "set_interval":
drivers/hwmon/lm95241.c:132:15: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_max2":
drivers/hwmon/lm95241.c:278:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_max1":
drivers/hwmon/lm95241.c:277:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_min2":
drivers/hwmon/lm95241.c:249:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_min1":
drivers/hwmon/lm95241.c:248:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_type2":
drivers/hwmon/lm95241.c:220:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_type1":
drivers/hwmon/lm95241.c:219:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
This also fixes a small race in set_interval() as a side effect: by
working with a temporary local variable we prevent data->interval from
being accessed at a time it contains the interval value in the wrong
unit.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Davide Rizzo <elpa.rizzo@gmail.com>
My old mail address doesn't exist anymore. This changes all occurrences
to my new address.
Signed-off-by: Hans J. Koch <hjk@hansjkoch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
In current implementation, the sysfs entries is not removed before return -ENODEV.
Creating the sysfs attribute should be the last thing done by the function,
after all the rest has been successful.
Otherwise there is a small window during which user-space can access the attribute
but the driver isn't ready to deal with the requests.
Fix it by moving sysfs_create_group to be the last thing done by the function.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Return proper error if i2c_check_functionality reports
the adapter does not support the capability we need.
Also remove unneeded initialization for err variable.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
adapter->id is deprecated and not set by any adapter driver, so this
was certainly not what the author wanted to use. adapter->nr maybe,
but as dev_err() already includes this value, as well as the client's
address, there's no point repeating them. Better print a simple error
message in plain English words.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for the IT8721F/IT8758E. These new chips differ from the
older IT87xxF chips in the following ways:
* ADC LSB is 12 mV instead of 16 mV.
* PWM values are 8-bit instead of 7-bit.
There are other minor changes we don't have to care about in the
driver.
Another change is that we will handle internal voltage scaling in the
driver instead of delegating the work to user-space.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Move conversion functions until after structure defintions. This is
needed for future changes which make use of the structures in the
conversion funtcions.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Remove the dependency on EXPERIMENTAL for all drivers which are in
the kernel tree for a long time, are known to work properly and for
which we have documentation.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Corentin Labbe <corentin.labbe@geomatys.fr>
Cc: Riku Voipio <riku.voipio@iki.fi>
Cc: Juerg Haefliger <juergh@gmail.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The ADT7468 supports a high-frequency PWM output mode where all PWM
outputs are driven by a 22.5 kHz clock. Add support for this mode, and
document it, as it may surprise the user that setting one PWM output
frequency also affects the other PWM outputs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The ADT7468 uses the same frequency table as the ADT7463.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Cc: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
We can mark normal_i2c const. Almost all drivers do that already, so
fix the 3 remaining ones before they are used as (bad) examples for
new drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: George Joseph <george.joseph@fairview5.com>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
The ams driver isn't a hardware monitoring driver, so it shouldn't
live under driver/hwmon. drivers/macintosh seems much more
appropriate, as the driver is only useful on PowerBooks and iBooks.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Stelian Pop <stelian@popies.net>
Cc: Michael Hanselmann <linux-kernel@hansmi.ch>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
The PCF8591 can't be detected, don't even try. There are plenty of
other means to instantiate i2c devices these days.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Register PCF8591 devices as hwmon devices. There's little point in
implementing the standard sysfs interface if we don't register it in
a way libsensors will pick it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Follow the standard attribute naming for the chassis intrusion
feature. I couldn't test the beeping (my board apparently doesn't do
that) but the alarm works fine.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The fan control feature of the w83795 driver is insufficiently
reviewed and tested for public consumption at this time, so make it
optional and disabled by default. We will change the default when
review and testing is deemed sufficient. Ultimately the option will
go away.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
I've made so many changes to the w83795 driver that it's only fair to
list myself as a co-author. I'll also maintain the driver for some
time. There's more work needed on the driver for sure.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cleanups suggested by Guenter Roeck, falling into 4 categories:
* Swapping test orders, because if (var == CONSTANT) is much easier to
read than if (CONSTANT == var).
* Simplifying comparisons with 0.
* Dropping unneeded masks.
* Dropping unneeded parentheses and curly braces.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
When we don't need the client pointer, calling dev_get_drvdata() is
more efficient that calling to_i2c_client() and then
i2c_get_clientdata().
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Wait until we need the pwm config register values, instead of
pre-reading them. This saves over 1 second on modprobe on my test
system.
Obviously this time is added when first accessing pwm config
attributes, however not everybody will use them, so it seems unfair
to slow down driver loading (and thus boot) for an optional feature.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Wait until we need the limit register values, instead of pre-reading
them. This saves 544 ms on modprobe on my test system. Obviously this
time is added when first running "sensors" or any other monitoring
application, but I think it is better than slowing down the boot.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Move initial register reads out of probe, to dedicated functions.
This makes the code clearer, and will be needed if we want to delay
calling these functions until they are needed, or want to call them
periodically.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cascaded conditionals are inefficient. Reorder the fields so that
PWM register addresses can be computed more efficiently.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
There is no point in reading registers during initialization if we
will refresh the values in the update function later. This is only
slowing down the driver loading with no benefit, stop doing it.
This change saves 480 ms on driver load on my test system.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
All 3 temperature sensor type sysfs functions (show_temp_mode,
store_temp_mode and show_dts_mode) can be simplified. We don't
create these files when the correponding input isn't in temperature
monitoring mode, so there is no point in handling that case.
Likewise, we don't allow changing inputs from temperature to voltage,
so the code handling this case is dead and can be removed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
VRLSB_SHIFT is a non-sense, the actual shift depends on the sensor
type (fans need 4, other sensors need 6). Get rid of it to prevent
any confusion. Also get rid of the useless masking, the meaningful
bits are always the MSb so there's nothing to mask out after
shifting.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Shorten driver load time by avoiding duplicate register access during
initialization. This saves 112 ms on modprobe on my test system.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Handle beep_enable just like all other beep bits. It doesn't need
anything special, so let's avoid redundant code. This also saves a
duplicate register read at initialization time.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The PWM duty cycle frequenty attributes are improperly named
(fanN_div instead of pwmN_div) and contain raw values instead of
actual frequencies. Rename them and fix their contents.
Also improve the logic when the user asks for a new frequency, to
always pick the closest supported frequency. The algorithm could
certainly be optimized, but the operation is infrequent enough that
I don't think it's worth the effort.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The W83795G can be configured to set the in0, in1 and/or in2 voltage
limits dynamically based on VID input pins. Switch the respective
sysfs attributes to read-only.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Misplaced parentheses caused the wrong register value to be read,
resulting in random LSB for fan speed values and limits.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* The data structure is zalloc'd, so no need to set individual fields
to 0 explicitly.
* Refactor the handling of pins that can be used for either
temperature or voltage monitoring.
* Misc other clean-ups.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Only create fan[1-8]_target files when the fan in question can be
controlled (PWM output is present.) Also name these files according
to the standard.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use a dedicated 2D array for PWM attributes. This way, PWM attributes
are handled the same way as other attributes, this is more consistent.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use 2D arrays for in, fan, temp and dts device attributes. Using
linear arrays is too risky as we have to skip some groups depending
on the device model and configuration. Adding or removing an
attribute would let the driver build silently but then it would crash
at runtime. With 2D arrays, the consistency checking happens at build
time, which is much safer.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Functions w83795_create_files and w83795_remove_files iterate over
the same set of files, just calling a different function. Merge them
into a single function which takes the action as a parameter. This
saves code, and also ensure that file creation and deletion are in
sync.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Function w83795_probe() is way too big, move file creation to a separate
function to make it more readable.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Sysfs files must be removed on device removal but also when device
registration fails. Move the code to a separate function to avoid
code redundancy.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Move the bank selection code to a separate function, to avoid
duplicating it in read and write functions. Improve error reporting
on register access error.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Enum chips and chip_types are redundant, get rid of the former. Fix
the detection code to properly identify the chip variant and name the
client accordingly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
There is still much work needed, but I wanted to give Wei the credit
he deserves. I've merged some of my own fixes already, to make
gcc and checkpatch happy. Individual fixes and improvements from me
will follow.
[JD: Fix build errors]
[JD: Coding style cleanups]
[JD: Get rid of forward declarations]
[JD: Drop VID support]
[JD: Drop fault output control feature]
[JD: Use lowercase for inline function names]
[JD: Use strict variants of the strtol/ul functions]
[JD: Shorten the read and write function names]
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This way we don't need to modify Kconfig every time a new SoC comes along to
make this driver support it. Also fix some typos while I'm at it.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The semaphore which protects the ADC is semantically a mutex. Use a
real mutex.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Currently we get the checkpatch warning
consider using strict_strtol in preference to simple_strtol.
Also we should not allow any partially numeric values.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
I was wondering if that chip ever existed publicly... Apparently yes,
so add support for it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Instead of using switch/case and if statements in probe, define chip specific
functionality in a parameter structure array.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The family check in k8temp is not required because the driver is
already bound to a northbridge device only used with K8 CPUs.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
If lis3lv02d_init_device fails, HW resources were not released
properly. In case of failure call release_resources if available.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Configure chip to data ready mode in selftest and count received
interrupts to see that interrupt line(s) are working.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add optional blockread function to interface driver. If available
the chip driver uses it for data register access. For 12 bit device
it reads 6 bytes to get 3*16bit data. For 8 bit device it reads out
5 bytes since every second byte is dummy.
This optimizes bus usage and reduces number of operations and
interrupts needed for one data update.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Default fuziness is set smaller for 8 device.
In 12 bit device LSB is quite close to 1 mg
(mg = 1 / 1000 of earth gravity).
In 8bit device LSB is about 18 mg.
Set fuziness to 1 for 8 bit device.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Added default output data rate setting to platform data.
If default rate is 0, reset default value is used.
Added control for duration via platform data.
Added possibility to configure interrupts to trig on
both rising and falling edge. The lis3 WU unit can be
configured quite many ways and with some configurations it
is quite handy to get coordinate refresh when some
event trigs and when it reason goes away.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
All axis enable bits are set to 0 at module remove.
Restore reset default value at init.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Sometimes lis3 chip seems to fail to setup factory tuning at boot up.
This probably happens if there is some odd power ramp down ramp up sequence
for example in device restart. Set boot bit in control2 register to
trig boot sequence manually and wait until it is finished.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Call input device poll function at device open to refresh coordinates
immediately. This is needed for the case where poll interval is set to
zero and coordinate updates happens purely under interrupt control.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Irqcfg moved to chip data instead of platform data.
This simplifies access in interrupt handler little bit.
Input device open and close functions set status for
interrupt threaded handler once.
Unnecessary check for interrupt source removed since
it is enough that active interrupt line indicates that
there was an interrupt.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Based on pm_runtime control, turn lis3 regulators on and off.
Perform context save and restore on transitions.
Feature is optional and must be enabled in platform data.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add pm_runtime support to lis3 core driver.
Add pm_runtime support to lis3 i2c driver.
spi and hp_accel drivers are not yet supported. Old always
on functionality remains for those.
For sysfs there is 5 second delay before turning off the
chip to avoid long ramp up delay.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch adds hwmon support for fans connected to GPIO lines.
Platform specific information such as GPIO pinout and speed conversion array
(rpm from/to GPIO value) are passed to the driver via platform_data.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
According to the documentation, simply reading the respective MSR
isn't sufficient: It should be written with zeros, cpuid(1) be
executed, and then read (see arch/x86/kernel/cpu/intel.c for an
example).
v2: Fail probe when microcode revision cannot be determined, but is
needed to check for proper operation.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Chen Gong <gong.chen@linux.intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
CONFIG_HOTPLUG_CPU is used too much in some drivers.
This patch clean them up.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
pkgtemp is derived from coretemp, so some reasonable
logics should be applied onto pkgtemp, too. Such as
the init logic here.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This driver adds support for Linear Technology LTC4261 I2C Negative
Voltage Hot Swap Controller.
Reviewed-by: Ira W. Snyder <iws@ovro.caltech.edu>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The axis-mapping of lis3dev device on many (rather most) HP machines
doesn't follow the standard. When each new model appears, users need to
adjust again. Testing this requires the rebuild of kernel, thus it's not
trivial for end-users.
This patch adds a module parameter "axes" to allow a custom axis-mapping
without patching and recompiling the kernel driver. User can pass the
parameter such as axes=3,2,1. Also it can be changed via sysfs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch is an enhanced version of Takashi Iwai's
[PATCH] hp_accel: Add quirks for HP ProBook 532x and HP Mini 5102
My HP Mini 5101 works fine with this patch.
Confirmed with Tux Racer.
Signed-off by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
A new version of LIS3 chip has slight incompatibilities from former
versions. This patch adds the minimal support for it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
These likely originate from these drivers being clones of one another
and/or other drivers which actually needed these includes.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
"break" after "return" is at best bogus (good compilers even warn about
the "break" being unreachable).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
... as they're being called only from a __cpuinit function.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86: (44 commits)
eeepc-wmi: Add cpufv sysfs interface
eeepc-wmi: add additional hotkeys
panasonic-laptop: Simplify calls to acpi_pcc_retrieve_biosdata
panasonic-laptop: Handle errors properly if they happen
intel_pmic_gpio: fix off-by-one value range checking
IBM Real-Time "SMI Free" mode driver -v7
Add OLPC XO-1 rfkill driver
Move hdaps driver to platform/x86
ideapad-laptop: Fix Makefile
intel_pmic_gpio: swap the bits and mask args for intel_scu_ipc_update_register
ideapad: Add param: no_bt_rfkill
ideapad: Change the driver name to ideapad-laptop
ideapad: rewrite the sw rfkill set
ideapad: rewrite the hw rfkill notify
ideapad: use EC command to control camera
ideapad: use return value of _CFG to tell if device exist or not
ideapad: make sure we bind on the correct device
ideapad: check VPC bit before sync rfkill hw status
ideapad: add ACPI helpers
dell-laptop: Add debugfs support
...
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
block: autoconvert trivial BKL users to private mutex
drivers: autoconvert trivial BKL users to private mutex
ipmi: autoconvert trivial BKL users to private mutex
mac: autoconvert trivial BKL users to private mutex
mtd: autoconvert trivial BKL users to private mutex
scsi: autoconvert trivial BKL users to private mutex
Fix up trivial conflicts (due to addition of private mutex right next to
deletion of a version string) in drivers/char/pcmcia/cm40[04]0_cs.c
The hdaps driver isn't a hardware monitoring driver, so it shouldn't
live under driver/hwmon. drivers/platform/x86 seems much more
appropriate, as the driver is only useful on x86 laptops.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The patch below updates broken web addresses in the kernel
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Ben Pfaff <blp@cs.stanford.edu>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
All these files use the big kernel lock in a trivial
way to serialize their private file operations,
typically resulting from an earlier semi-automatic
pushdown from VFS.
None of these drivers appears to want to lock against
other code, and they all use the BKL as the top-level
lock in their file operations, meaning that there
is no lock-order inversion problem.
Consequently, we can remove the BKL completely,
replacing it with a per-file mutex in every case.
Using a scripted approach means we can avoid
typos.
These drivers do not seem to be under active
maintainance from my brief investigation. Apologies
to those maintainers that I have missed.
file=$1
name=$2
if grep -q lock_kernel ${file} ; then
if grep -q 'include.*linux.mutex.h' ${file} ; then
sed -i '/include.*<linux\/smp_lock.h>/d' ${file}
else
sed -i 's/include.*<linux\/smp_lock.h>.*$/include <linux\/mutex.h>/g' ${file}
fi
sed -i ${file} \
-e "/^#include.*linux.mutex.h/,$ {
1,/^\(static\|int\|long\)/ {
/^\(static\|int\|long\)/istatic DEFINE_MUTEX(${name}_mutex);
} }" \
-e "s/\(un\)*lock_kernel\>[ ]*()/mutex_\1lock(\&${name}_mutex)/g" \
-e '/[ ]*cycle_kernel_lock();/d'
else
sed -i -e '/include.*\<smp_lock.h\>/d' ${file} \
-e '/cycle_kernel_lock()/d'
fi
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Sleep while acquiring a resource lock on the Super I/O port. This should
prevent collisions from causing the hardware probe to fail with -EBUSY.
Signed-off-by: Giel van Schijndel <me@mortis.eu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Commit e40cc4bdfd introduced
a build breakage if CONFIG_SMP is undefined. This commit
fixes the problem.
This fix is only a workaround. For a real fix, cpu_sibling_mask() should
be defined in UP include code, eg in linux/smp.h, and asm/smp.h should not be
included directly. This fix is currently not possible because asm/smp.h defines
cpu_sibling_mask() unconditionally and is included directly from many source
files.
Reported-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Other than coretemp, from which this code was apparently derived, there
is no PCI specific code in this driver.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Just like pkgtemp registers another core of the same package when one
gets removed, coretemp should register another hyperthread (if
available) in that situation.
As pointed out in the patch fixing the respective code in pkgtemp, the
list protectng mutex must be dropped before calling
coretemp_device_add(), and due to the restructured loop (including an
explicit return) the "safe" variant of the list iterator isn't needed
anymore.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Feature availability should also be checked in the hotplug code path.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Using cpuid_eax() to determine feature availability on other than
the current CPU is invalid. And feature availability should also be
checked in the hotplug code path.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
pkgtemp_device_remove(), holding the list protecting mutex, calls
pkgtemp_device_add(), which itself wants to acquire the same mutex.
Holding the mutex over the entire loop body in pkgtemp_device_remove()
isn't really necessary, as long as the loop gets exited after
processing the matched CPU.
Once exiting the loop after removing an eventual match, there's no
need for using the "safe" list iterator anymore.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
In commit 0dca94baea the call to
platform_driver_unregister() was made conditional upon !HOTPLUG_CPU,
but the return value from coretemp_init() was left to indicate an
error. This isn't correct, as the negative return value indicates to
the module loader that initialization failed, which isn't intended
here and results in dangling pointers.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The recent addition of threaded irq handler causes a NULL dereference
when used with hp_accel driver, which has NULL pdata.
Acked-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
update_interval is the matching attribute defined in the hwmon sysfs ABI.
Use it.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The attribute reflects an interval, not a rate.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
According to the datasheet for Winbond W83627DHG the proper way to exit
the Extended Function Mode is to write 0xaa to the EFER(0x2e or 0x4e).
Signed-off-by: Jonas Jonsson <jonas@ludd.ltu.se>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
It is unnecessary and wrong to call hwmon_device_unregister in error
handling before hwmon_device_register is called.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
All bits in the values read from registers to be used for the next
write were getting overwritten, avoid doing so to not mess with the
current configuration.
Signed-off-by: Guillem Jover <guillem@hadrons.org>
Cc: Riku Voipio <riku.voipio@iki.fi>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The spec notes that fan0 and fan1 control mode bits are located in bits
7-6 and 5-4 respectively, but the FAN_CTRL_MODE macro was making the
bits shift by 5 instead of by 4.
Signed-off-by: Guillem Jover <guillem@hadrons.org>
Cc: Riku Voipio <riku.voipio@iki.fi>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
If CONFIG_PM was selected and lis3lv02d_platform_data was NULL,
the kernel will be panic when halt command run.
Reported-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Sigend-off-by: Jean Delvare <khali@linux-fr.org>
Added missing axis-mapping for HP ProBook 532x and HP Mini 5102.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 8bf0223ed515be24de0c671eedaff49e78bebc9c (hwmon, k8temp: Fix
temperature reporting for ASB1 processor revisions) fixed temperature
reporting for ASB1 CPUs. But those CPU models (model 0x6b, 0x6f, 0x7f)
were packaged both as AM2 (desktop) and ASB1 (mobile). Thus the commit
leads to wrong temperature reporting for AM2 CPU parts.
The solution is to determine the package type for models 0x6b, 0x6f,
0x7f.
This is done using BrandId from CPUID Fn8000_0001_EBX[15:0]. See
"Constructing the processor Name String" in "Revision Guide for AMD
NPT Family 0Fh Processors" (Rev. 3.46).
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: stable@kernel.org [.32.x, .33.x, .34.x, .35.x]
Reported-by: Vladislav Guberinic <neosisani@gmail.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix the following build warning:
CC [M] drivers/hwmon/coretemp.o
drivers/hwmon/coretemp.c: In function "coretemp_init":
drivers/hwmon/coretemp.c:521: warning: unused variable "n"
drivers/hwmon/coretemp.c:521: warning: unused variable "p"
Introduced by commit 851b29cb3b. When
you drop code, you also have to drop the variables this code was
using.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Chen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
Revert commit 7721fea3d0 ("hwmon:
f71882fg: add support for the Fintek F71808E").
Hans said:
: A second review after I've received a data sheet for this device from
: Fintek has turned up a few bugs.
:
: Unfortunately Giel (nor I) have time to fix this in time for the 2.6.36
: cycle. Therefor I would like to see this patch reverted as not having any
: support for the hwmon function of this superio chip is better then having
: unreliable support.
Cc: Giel van Schijndel <me@mortis.eu>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The via-cputemp hwmon driver was probably intending "typedef enum {
... } SHOW;", but the "typedef" was missing creating a global variable
named "SHOW". There is absolutely no reason to have this in the
global namespace.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Acked-by: Harald Welte <HaraldWelte@viatech.com>
Cc: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
jc42 uses i2c interfaces, so it should depend on I2C.
drivers/hwmon/jc42.c:426: error: implicit declaration of function 'i2c_check_functionality'
drivers/hwmon/jc42.c:521: error: implicit declaration of function 'i2c_smbus_read_word_data'
drivers/hwmon/jc42.c:529: error: implicit declaration of function 'i2c_smbus_write_word_data'
drivers/hwmon/jc42.c:580: error: implicit declaration of function 'i2c_add_driver'
drivers/hwmon/jc42.c:585: error: implicit declaration of function 'i2c_del_driver'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The sysfs file removal code is the same in the probe error path and in
the remove function, so move it to a separate function to avoid code
duplication.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for the 6 temperature monitoring channels of the PC87427.
Note that the sensors resolution can vary, and I couldn't find a way
to figure it out, so we might have to compensate in user-space.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The second logical device contains the voltage and temperature
registers. We have to extend the driver to support a second logical
device before we can add support for these features.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add initial support for PWM outputs of the PC87427 Super-I/O chip.
Only mode change and manual fan speed control are supported. Automatic
mode configuration isn't supported, and won't be until at least one
board is known, which makes uses of the PWM outputs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Most fan input pins of the PC87427 can have alternate functions.
Update the driver to check the configuration register and only support
fan inputs which are really used for fan monitoring.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for W83667HG-B (very similar to the W83667HG).
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
- Moved fan pwm register array pointers into per-instance data.
- Only read fan pwm data for installed/supported fans.
- Update fan max output and fan step output information from data in
registers.
- Create max_output and step_output attribute files only if respective
fan pwm registers exist.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
SMSC's EMC2103 family of temperature/fan controllers have 1
onboard and up to 3 external temperature sensors, and allow
closed-loop control of one fan. This patch adds support for
them.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* The dev variable is never used.
* Detect functions only need to set info->type, not client->name.
* Include the device address in the log message.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: George Joseph <george.joseph@fairview5.com>
Cc: Ken Milmore <ken.milmore@googlemail.com>
Some voltage sensors can be wired internally to the IT87xxF chip's own
power supply channels. In that case, we can inform user-space that the
wiring is known by exporting proper labels for these sensors.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
There is a shutdown feature at suspend it can be enabled to
reduce current consumption and resume it can be switched off.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti@ti.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add back the power interface we lost due to a slight misunderstanding of
the maintainers wishes.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for exposing all GPIO pins as analog voltages. Though this is
not an ideal use of the chip, some hardware engineers may decide that the
LTC4245 meets their design requirements when studying the datasheet.
The GPIO pins are sampled in round-robin fashion, meaning that a slow
reader will see stale data. A userspace application can detect this,
because it will get -EAGAIN when reading from a sysfs file which contains
stale data.
Users can choose to use this feature on a per-chip basis by using either
platform data or the OF device tree (where applicable).
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
It's not OK to call platform_device_add_resources() multiple times
in a row. Despite its name, this functions sets the resources, it
doesn't add them. So we have to prepare an array with all the
resources, and then call platform_device_add_resources() once.
Before this fix, only the last I/O resource would be actually
registered. The other I/O resources were leaked.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: stable@kernel.org
Move the if(err) statement after the if into the if branch indicated by its
indentation. The preceding if(err) test implies that err cannot be nonzero
unless the if branch is taken.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable braces5@
position p1,p2;
statement S1,S2;
@@
(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
if (p1[0].column == p2[0].column):
cocci.print_main("branch",p4)
cocci.print_secs("after",p5)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
There is a shiny new mc13783 API function that can be used instead.
While at it refactor the code a bit to reduce code duplication a bit.
This removes the last user of <linux/mfd/mc13783-private.h> and so this
include file can go away.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In commit 0dca94baea ("hwmon: coretemp: update hotplug condition
check") we merged v2 of this patch. Update that to v3.
The difference is to remove the new and unnecesary references to
CPU_*_FROZEN.
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Chen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow device probing to recognise the Fintek F71808E.
Sysfs interface:
* Fan/pwm control is the same as for F71889FG
* Temperature and voltage sensor handling is largely the same as for
the F71889FG
- Has one temperature sensor less (doesn't have temp3)
- Misses one voltage sensor (doesn't have V6, thus in6_input refers to
what in7_input refers for F71889FG)
For the purpose of the sysfs interface fxxxx_in_temp_attr[] is split up
such that it can largely be reused.
Signed-off-by: Giel van Schijndel <me@mortis.eu>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
register_hotcpu_notifier() is designed to make these ifdefs unnecessary.
Cc: Chen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update coretemp supported CPU TjMax lists and some cleanup work.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If one coretemp device can't be added, it should allow subsequent adding
operation because every new-added device will create a new sysfs group,
not an additional sensor sys entry.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix two errors in hotplug. One is for hotplug notifier. The other is
unnecessary driver unregister. Because even none of online cpus supports
coretemp, we can't assume new onlined cpu doesn't support it either. If
related driver is unregistered there we have no chance to use coretemp
from then on.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver adds support for the monitoring features of the Summit
Microelectronics SMM665 Six-Channel Active DC Output Controller/Monitor.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add Lenovo Thinkpad T400. I have done the testing on my laptop. The
hdaps module detects the device and the hdapsd daemon is able to [un]park
the disk.
Signed-off-by: Ritesh Raj Sarraf <rrs@debian.org>
Cc: Frank Seidel <frank@f-seidel.de>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (63 commits)
of/platform: Register of_platform_drivers with an "of:" prefix
of/address: Clean up function declarations
of/spi: call of_register_spi_devices() from spi core code
of: Provide default of_node_to_nid() implementation.
of/device: Make of_device_make_bus_id() usable by other code.
of/irq: Fix endian issues in parsing interrupt specifiers
of: Fix phandle endian issues
of/flattree: fix of_flat_dt_is_compatible() to match the full compatible string
of: remove of_default_bus_ids
of: make of_find_device_by_node generic
microblaze: remove references to of_device and to_of_device
sparc: remove references to of_device and to_of_device
powerpc: remove references to of_device and to_of_device
of/device: Replace of_device with platform_device in includes and core code
of/device: Protect against binding of_platform_drivers to non-OF devices
of: remove asm/of_device.h
of: remove asm/of_platform.h
of/platform: remove all of_bus_type and of_platform_bus_type references
of: Merge of_platform_bus_type with platform_bus_type
drivercore/of: Add OF style matching to platform bus
...
Fix up trivial conflicts in arch/microblaze/kernel/Makefile due to just
some obj-y removals by the devicetree branch, while the microblaze
updates added a new file.
This patch adds a hwmon driver for package level thermal control. The driver
dumps package level thermal information through sysfs interface so that upper
level application (e.g. lm_sensor) can retrive the information.
Instead of having the package level hwmon code in coretemp, I write a seperate
driver pkgtemp because:
First, package level thermal sensors include not only sensors for each core,
but also sensors for uncore, memory controller or other components in the
package. Logically it will be clear to have a seperate hwmon driver for package
level hwmon to monitor wider range of sensors in a package. Merging package
thermal driver into core thermal driver doesn't make sense and may mislead.
Secondly, merging the two drivers together may cause coding mess. It's easier
to include various package level sensors info if more sensor information is
implemented. Coretemp code needs to consider a lot of legacy machine cases.
Pkgtemp code only considers platform starting from Sandy Bridge.
On a 1Sx4Cx2T Sandy Bridge platform, lm-sensors dumps the pkgtemp and coretemp:
pkgtemp-isa-0000
Adapter: ISA adapter
physical id 0: +33.0°C (high = +79.0°C, crit = +99.0°C)
coretemp-isa-0000
Adapter: ISA adapter
Core 0: +32.0°C (high = +79.0°C, crit = +99.0°C)
coretemp-isa-0001
Adapter: ISA adapter
Core 1: +32.0°C (high = +79.0°C, crit = +99.0°C)
coretemp-isa-0002
Adapter: ISA adapter
Core 2: +32.0°C (high = +79.0°C, crit = +99.0°C)
coretemp-isa-0003
Adapter: ISA adapter
Core 3: +32.0°C (high = +79.0°C, crit = +99.0°C)
[ hpa: folded v3 patch removing improper global variable "SHOW" ]
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
LKML-Reference: <1280448826-12004-3-git-send-email-fenghua.yu@intel.com>
Reviewed-by: Len Brown <len.brown@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Both of_bus_type and of_platform_bus_type are just #define aliases
for the platform bus. This patch removes all references to them and
switches to the of_register_platform_driver()/of_unregister_platform_driver()
API for registering.
Subsequent patches will convert each user of of_register_platform_driver()
into plain platform_drivers without the of_platform_driver shim. At which
point the of_register_platform_driver()/of_unregister_platform_driver()
functions can be removed.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
Don't assume that CPU entry number and core ID always match. It
worked in the simple cases (single CPU, no HT) but fails on
multi-CPU systems.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Huaxu Wan <huaxu.wan@intel.com>
Cc: stable@kernel.org