o Currently, during kexec reboot, IOAPIC is re-programmed back to virtual
wire mode if there was an i8259 connected to it. This enables getting
timer interrupts in second kernel in legacy mode.
o After putting into virtual wire mode, IOAPIC delivers the i8259 interrupts
to CPU0. This works well for kexec but not for kdump as we might crash
on a different CPU and second kernel will not see timer interrupts.
o This patch modifies the redirection table entry to deliver the timer
interrupts to the cpu we are rebooting (instead of hardcoding to zero).
This ensures that second kernel receives timer interrupts even on a
non-boot cpu.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When we re-calibrate the frequency, it is likely that an interrupt (as for
example the main system clock) will be triggered by the system. Therefore
the calibration may not be accurate. This will also provide a fix to bug
#5266.
Many thanks to Larry Finger for helping resolving this issue.
Signed-off-by: Bruno Ducrot <ducrot@poupinou.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Fix screen blanking on BIOSes that return APM_NOT_ENGAGED when APM enabled
screen blanking is not turned on.
The original code only tried to set the state on device 0x100, and then
0x1FF, and I added 0x101 to the mix too.
- Clean up logic in apm_console_blank().
- Prevent the error message from printing out twice.
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Provide basic support for the AMD Geode GX and LX processors.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removed the unused variable "rv".
Signed-off-by: Daniel Marjamaki <daniel.marjamaki@comhem.se>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removed the unused variable "rv".
Signed-off-by: Daniel Marjamaki <daniel.marjamaki@comhem.se>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Missing newline in printk.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The 'make rodata read-only' patch in -mm exposes a latent bug in the 32-bit
change_page_attr() function, which causes certain CPUs (Those with NX
basically) to reboot instantly after pages are marked read-only.
The same bug got fixed a while back on x86-64, but never got propagated to
i386.
Stuart Hayes from Dell also picked up on this last June, but it never got
fixed, as the only thing affected by it aparently was the nvidia driver.
Blatantly stealing description from his post..
"It doesn't appear to be fixed (in the i386 arch). The
change_page_attr()/split_large_page() code will still still set all the
4K PTEs to PAGE_KERNEL (setting the _PAGE_NX bit) when a large page
needs to be split.
This wouldn't be a problem for the bulk of the kernel memory, but there
are pages in the lower 4MB of memory that's free, and are part of large
executable pages that also contain kernel code. If change_page_attr()
is called on these, it will set the _PAGE_NX bit on the whole 2MB region
that was covered by the large page, causing a large chunk of kernel code
to be non-executable."
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: <Stuart_Hayes@Dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If we are using hotplug enabled kernel, then make bigsmp the default mode.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow SPARSEMEM to be enabled on non-numa x86 systems. This is made
dependant on EXPERIMENTAL also being set. When an in-tree user (such as
simulated numa) exists it should be made dependant on that.
The plan is to have no options and no selector as normal when
!EXPERIMENTAL. When EXPERIMENTAL we enable the FLATMEM and SPARSEMEM
options for X86_PC whilst maintaining DISCONTIGMEM and SPARSEMEM for NUMA.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Mark some key kernel datastructures readonly. This patch was previously
posted on Jun 28th but was back then not merged because nothing was enforcing
rodata anyway.. well that changed now :)
Patch by Christoph Lameter <christoph@lameter.com> and Dave Jones
<davej@redhat.com>
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
x86-64 specific parts to make the .rodata section read only
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bug fix required for the .rodata work on x86-64:
when change_page_attr() and friends need to break up a 2Mb page into 4Kb
pages, it always set the NX bit on the PMD, which causes the cpu to consider
the entire 2Mb region to be NX regardless of the actual PTE perms. This is
fine in general, with one big exception: the 2Mb page that covers the last
part of the kernel .text! The fix is to not invent a new permission for the
new PMD entry, but to just inherit the existing one minus the PSE bit.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
x86 specific parts to make the .rodata section read only
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the "temporary debugging check" which has managed to live for quite
some time, and is clearly unneeded. The mm can never be live at this point,
so clearly checking the LDT in the mm->context is redundant as well.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
APM BIOS code has a protective wrapper that runs it only on CPU zero. Thus,
no need to set APM BIOS segments in the GDT for other CPUs.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Acked-by: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Stop deleting NT bit from EFLAGS. See arch/i386/kernel/head.S line 223, which
does something even better.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
PnP BIOS data, code, and 32-bit entry segments all have fixed limits as well;
set them in the GDT rather than adding more code. It would be nice to add
these fixups to the boot GDT rather than setting the GDT for each CPU; perhaps
I can wiggle this in later, but getting it in before the subsys init looks
tricky.
Also, make some progress on deprecating the ugly Q_SET_SEL macros.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The one remaining caller of set_limit, the PnP BIOS code, calls into the PnP
BIOS, passing kernel parameters in and out. These parameteres may be passed
from arbitrary kernel virtual memory, so they deserve strict protection to
stop a bad BIOS from smashing beyond the object size.
Unfortunately, the use of set_limit was badly botching this by setting the
limit in terms of pages, when it really should have byte granularity.
When doing this, I discovered my BIOS had the buggy code during the "get
system device node" call:
mov ax, es:[bx]
Which is harmless, but has a trivial workaround.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since APM BIOS segment limits are now fixed, set them in head.S GDT and don't
use the complicated _set_limit() macro expansion.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Acked-by: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
APM BIOSes have many bugs regarding proper representation of the appropriate
segment limits for calling the BIOS. By default, APM_RELAX_SEGMENTS is always
turned on to support running the APM BIOS on these buggy machines. Keeping
64k limits poses very little danger to the kernel, because the pages where the
APM BIOS is located will always be in low physical memory BIOS areas, which
should already be marked reserved, and only buggy BIOSes would possibly
overstep the segment bounds with writes to data anyway.
Since forcing stricter limits breaks many machines and is not default
behavior, it seems reasonable to deprecate the older code which may cause APM
BIOS to fault.
If you really have a badly enough broken APM BIOS that you have to turn off
APM_RELAX_SEGMENTS, seems like the best recourse here would be to disable the
APM BIOS and / or not compile it into your kernel to begin with, and / or add
your system to the known bad list.
The reason I want to deprecate this code is there is underlying brokenness
with the set_limit macros, and getting rid of many of the call sites rather
than rewriting them seems to be the simplest and most correct course of
action.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Acked-by: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
So some 486 processors do have CR4 register. Allow them to present it in
register dumps by using the old fault technique rather than testing processor
family.
Thanks to Maciej for noticing this.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Other than apparently commonly assumed, the bound instruction does not
require the corresponding IDT entry to have DPL 3.
Acked-by: "Seth, Rohit" <rohit.seth@intel.com>
Acked-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move some code unrelated to any dealing with hardware bugs from i386's
bugs.h to a more logical place.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rather than blindly re-enabling interrupts in die(), save their state
upon entry and then restore that state.
If the kernel is in really bad condition and faults with interrupts disabled,
re-enabling them in die() may cause even more trouble, implying more chances
of data corruption.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make GDT page aligned and page padded to support running inside of a
hypervisor. This prevents false sharing of the GDT page with other hot
data, which is not allowed in Xen, and causes performance problems in
VMware.
Rather than go back to the old method of statically allocating the GDT
(which wastes unneded space for non-present CPUs), the GDT for APs is
allocated dynamically.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch improves the signal handling:
(1) It makes do_signal() static as it isn't called from anywhere outside of
the arch code.
(2) It removes the regs argument to all the static functions within that file,
using __frame instead (which is the same thing held in a global register).
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch makes FRV signal handling work properly:
(1) After do_notify_resume() has been called, the work flags must be checked
again (there may be another signal to deliver or the process might require
rescheduling for instance).
(2) After the signal frame is set up on the userspace stack, ptrace() should
be given an opportunity to single-step into the signal handler.
(3) The error state from setting up a signal frame should be passed back up
the call chain.
(4) The segfault handler shouldn't be preemptively reset in the arch if we
fail to deliver a SEGV signal: force_sig() will take care of that.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch implements futex operations for the FRV architecture. The
operations are applicable to both MMU and no-MMU modes; though the EFAULT
handling will be a little bit of wasted space on the latter.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Commit 3e9e7c1d0b (ppc32: cleanup AMCC PPC40x
eval boards to support U-Boot) broke the kernel for ML300 / EP405.
It still compiles as there's a weak definition of the function in
misc-embedded.c, but the kernel crashes as the bd_t fixup isn't performed.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some custom cards might not need PCI, without this patch, compilation fails.
Signed-off-by: Roger Blofeld <blofeldus@yahoo.com>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We were counting on the bootloader to init some stuff, like get the bus out of
reset and enable accesses.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch takes care of an errata of the MPC5200 by avoiding 32 bits access
in type 1 configuration accesses. All others accesses are still 32 bits wide.
It also adds some mb() since the simple out_be(...) are not sufficient in
this case.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The mpc52xx_pci_fixup_resources is not only called at init but also when there
is a pci hotplug like when a cardbus card is plugged in. So that function is
needed after init too.
Thanks to Asier Llano Palacios for reporting this.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current iomapping used MBAR_SIZE for the size argument of
io_block_mapping, resulting in a call to setbat with a size argument of 64k
which is invalid.
This patch correct this and maps the whole 0xf0000000->0xffffffff range so
that devices on the local bus are also included in the BAT mapping.
Thanks to Bernhard Kuhn from Metrowerks for pointing this out.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
That file is a left-over of the 'old' OCP model that should have been erased
during the change to platform model but I forgot it ...
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Disable declaration of cpu variable in default_idle function when
building non-SMP kernels.
Signed-off-by: Otavio Salvador <otavio@debian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the not needed anymore "jumbo" member from ocp_func_emac_data.
Jumbo frame support is handled by PPC4xx EMAC driver internally now.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that i2c_add_driver() doesn't need the module owner to be set by
hand, we can delete it from the drivers. This patch catches all of the
drivers that I found in the current tree (if a driver sets the .owner by
hand, it's not a problem, just not needed.)
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Jean Delvare <khali@linux-fr.org>
We should use the i2c_driver.driver's .name and .owner fields
instead of the i2c_driver's ones.
This patch updates the drivers for arm arch.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
CC: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make I2C_CLIENT_ALLOW_USE the default for all i2c clients. It doesn't
hurt if the usage count is actually never used for any given driver,
and allows for nice code simplifications in i2c-core.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Just about every i2c chip driver sets the I2C_DF_NOTIFY flag, so we
can simply make it the default and drop the flag. If any driver really
doesn't want to be notified when i2c adapters are added, that driver
can simply omit to set .attach_adapter. This approach is also more
robust as it prevents accidental NULL pointer dereferences.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Setting RF (resume flag) allows a debugger to resume execution after a
code breakpoint without tripping the breakpoint again. It is reset by
the CPU after execution of one instruction.
Requested by Stephane Eranian:
"I am trying to the user HW debug registers on i386 and I am running
into a problem with ptrace() not allowing access to EFLAGS_RF for
POKEUSER (see FLAG_MASK). [ ... ] It avoids the need to remove the
breakpoint, single step, and reinstall. The equivalent functionality
exists on IA-64 and is allowed by ptrace()"
Cc: Stephane Eranian <eranian@hpl.hp.com>
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch/ia64/kernel/setup.c: In function `show_cpuinfo':
arch/ia64/kernel/setup.c:576: warning: long unsigned int format, different type arg (arg 12)
arch/ia64/kernel/setup.c:576: warning: long unsigned int format, different type arg (arg 13)
Introduced by 95235ca2c2
Signed-off-by: Tony Luck <tony.luck@intel.com>
Patch from Jared Hulbert
The following patch changes the bus arbiter controller settings
for the Intel PXA27x Application Processor Family. Up to 5%
better video performance. It parks the bus on the core while not
in use and sets the arbitration for other bus items. The patch
only applies changes to the Intel Mainstone development platform.
This patch is not compatible with preproduction Intel PXA27x
silicon.
This patch is based on the Intel Linux Preview Kit released to the
public on 25 Feb. 2005 found at
ftp://ftp.arm.linux.org.uk/pub/linux/arm/people/xscale/mainstone/02-25-2005/.
Signed-off-by: Justin A Treon <justin_treon@yahoo.com>
Signed-off-by: Jared Hulbert <jaredeh@gmail.com>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
The expansion bus on the IXP46x NPU can be configured for either 32MiB or
16MiB windows and changing the configuration causes the base address for
each chip select for each region to change. Because of this, we cannot
hardcode the physical base as we currently do. This patch checks the
expansion bus configuration registers at runtime to determine the
appropriate window size. Note that this requires that the bootloader
already configured the device sizes appropriately, but I feel that is
valid assumption to make as the bootloader must configure and access
the flash window, the output display (LCD, LEDs, etc) window, and
other expansion bus devices.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dan Williams
Convert old-style serial devices to platform devices so that printk's are visible during the boot process.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
- remove unnecessary mappings
- rename mx1ads_device to cs89x0_device, because
that's what it is
- fix io/irq resource for cs89x0 device
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
The SL-Cxx00 devices have a power control register in SCOOP that is
shared by both CF and MMC/SD card slots. The CF reset code was resetting
this register leading to various lockups as the MMC power was suddenly
lost. This patch handles the CPR register in a more sensitive manner.
It also removes some unneeded collie specific calls as the reset code
handles this.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
ARM doesn't use ACPI so ARM's apm implementation has no need to depend
on PM_LEGACY. This patch removes that dependency.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
This patch moves a large chunk of the sharpsl_pm driver to
arch/arm/common so that it can be reused on other devices such as the
SL-5500 (collie). It also abstracts some functions from the core into
the machine and platform specific parts of the driver to aid reuse.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add platform code to enable the ohci device on the pxa27x based
Sharp Zaurus Cxx00 devices.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
According to the manual, INT 6 is "invalid opcode", not "invalid operand".
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In particular, allow over-large read- or write-requests to be downgraded
to a more reasonable range, rather than considering them outright errors.
We want to protect lower layers from (the sadly all too common) overflow
conditions, but prefer to do so by chopping the requests up, rather than
just refusing them outright.
Cc: Peter Anvin <hpa@zytor.com>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Al Viro <viro@ftp.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The first of these changes s/hotplug/uevent/ was needed to
compile sn2_defconfig (ia64/sn). The other three files
changed are blind changes of all remaining bus_type.hotplug
references I could find to bus_type.uevent.
This patch attempts to finish similar changes made in the
gregkh-driver-kill-hotplug-word-from-driver-core Nov 22 patch.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Leave the overloaded "hotplug" word to susbsystems which are handling
real devices. The driver core does not "plug" anything, it just exports
the state to userspace and generates events.
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To allow multiple platforms to use the PXA27x OHCI driver, the platform
code needs to be moved into the board specific files in
arch/arm/mach-pxa. This patch does this for mainstone and adds
preliminary hooks to allow other boards to use the driver.
This has been compile tested for mainstone and successfully run on Spitz
(Sharp Zaurus SL-C3000) with the addition of an appropriate board
support file.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Deepak Saxena
Add NAS 100d to machine build list and update to new 2.6.15 options.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
---
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Rod Whitby
PAGE_SHIFT is undeclared in include/asm-arm/arch-ixp4xx/memory.h, identified by the following kernel compilation error:
CC [M] sound/core/memory.o
In file included from include/asm/memory.h:27,
from include/asm/io.h:28,
from sound/core/memory.c:24:
include/asm/arch/memory.h: In function `__arch_adjust_zones':
include/asm/arch/memory.h:28: error: `PAGE_SHIFT' undeclared (first use
in this function)
This patch replaces my previous attempt at fixing this problem (Patch 3214/1) and is based on the following feedback:
Russell King wrote:
> The error you see came up on SA1100. The best solution was to move
> the __arch_adjust_zones() function out of line. I suggest ixp4xx
> does the same.
I have moved the function out of line into arch/arm/mach-ixp4xx/common-pci.c as suggested.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
This patch removes referneces to gpio_isr_line_clear() from the
NAS 100d platform implementation.
Depends on 3192/1 and 3215/1
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Rod Whitby
This patch adds support for a new arm/ixp4xx machine - the Iomega NAS 100d network attached storage product. The NAS100D is a consumer device containing a 266MHz Intel IXP420 processor, 16MB of flash, 64MB of RAM, a 160Gb internal IDE hard disk, and 802.11b/g wireless on an Atheros mini-PCI card.
Work on porting the latest 2.6.x kernel to this device is being done by
the NSLU2-Linux project (the same team who maintains the port to the
Linksys NSLU2 device). In particular, the majority of this patch was
authored by Alessandro Zummo, based on the work done for MACH_NSLU2
support by the NSLU2-Linux core team of developers.
MACH_NAS100D (as implemented by this patch) can be enabled in jumbo
ixp4xx kernels without any affect on the other machines supported by
that kernel.
This patch applies cleanly against 2.6.15-rc7 and should be trivial to
apply to later kernel versions. It does not depend upon any other
patches.
Modified files (and number of lines inserted):
arch/arm/mach-ixp4xx/Kconfig | 8
arch/arm/mach-ixp4xx/Makefile | 1
include/asm-arm/arch-ixp4xx/hardware.h | 1
include/asm-arm/arch-ixp4xx/irqs.h | 9
include/asm-arm/arch-ixp4xx/nas100d.h | 75
arch/arm/mach-ixp4xx/nas100d-pci.c | 77
arch/arm/mach-ixp4xx/nas100d-power.c | 69
arch/arm/mach-ixp4xx/nas100d-setup.c | 133
-- Rod Whitby (NSLU2-Linux project lead)
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
Other than interrupt masking purposes, this API is only used when
configuring interrupt lines and this patch moves that functionality
directly into the ixp4xx_set_irq_type() implementation as board level
PCI code should not need to worry about those details.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since we now only build arch/arm/kernel/dma.c on machine types
which set ISA_DMA_API, we don't need to define MAX_DMA_CHANNELS
to 0 to indicate this - this definition becomes superfluous.
Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ISA_DMA_API tells the rest of the kernel if the ISA DMA API is
available. Select this symbol only on machine types which make
use of the ISA DMA API.
Make building of arch/arm/kernel/dma.c depend on this symbol -
if a machine does not support the ISA DMA API, it's pointless
building this file.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no need to have DMA initialised at the same time as
interrupts. Move it to a core_initcall().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The old __address element in struct scatterlist remained from older
kernels because the ARM DMA emulation code made use of it. Move
this field into struct dma_struct, and convert DMA emulation code
to setup a SG entry as required.
Also, convert DMA emulation code to use the new DMA API rather
than the PCI DMA API.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the compiler to optimise the bus_to_virt(virt_to_bus())
transformation in the ARM ISA DMA interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
CLPS711x, EPXA10DB and Integrator contained a dma.c file which has never
been built. Remove these redundant files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The function ia64_pci_legacy_write() returns 0 for everything
except errors. This return value gets sent back to the user from
pci_write_legacy_io(), making it look like every write fails. The trivial
patch below copies the behavior of the SGI sn machvec and does what
would be expected from something implementing a write() function.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
It seems that clk_use() and clk_unuse() are additional complexity
which isn't required anymore. Remove them from the clock framework
to avoid the additional confusion which they cause, and update all
ARM machine types except for OMAP.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/kernel/entry-armv.S has contained a comment suggesting
that asm/hardware.h and asm/arch/irqs.h should be moved into the
asm/arch/entry-macro.S include. So move the includes to these
two files as required.
Add missing includes (asm/hardware.h, asm/io.h) to asm/arch/system.h
includes which use those facilities, and remove asm/io.h from
kernel/process.c.
Remove other unnecessary includes from arch/arm/kernel, arch/arm/mm
and arch/arm/mach-footbridge.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We are coding the kernel link address into the makefiles, which is
invisibly dependent on PAGE_OFFSET. If PAGE_OFFSET is changed, the
makefiles also need to be changed.
Make adjustments such that the makefiles encode just the offset from
PAGE_OFFSET for the kernel link address, and use PAGE_OFFSET in the
linker scripts directly.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Sonny has noticed hotplug CPU on ppc64 is broken in 2.6.15-*. One of the
problems is that htab_initialize_secondary is called when a cpu is being
brought up, but it is marked __init.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently, we do not pass the correct start_pfn to e820_hole_size, to
calculate holes. Following patch fixes that.
The bug results in incorrect number of node_present_pages for each pgdat
and causes ugly output in /sys and probably VM inbalances.
Signed-off-by: Alok N Kataria <alokk@calsoftinc.com>
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Sighed-off-by: Shair Fultheim <shai@scalex86.org>
Sighed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix UML compilation when SKAS mode is disabled. Indeed, we were compiling
SKAS-only object files, which failed due to some SKAS-only headers being
excluded from the search path.
Thanks to the bug report from Pekka J Enberg.
Acked-by: Pekka J Enberg <penberg (at) cs ! helsinki ! fi>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Today, when compiling UML, I got warnings for two used unexported symbols:
readdir64 and truncate64. Indeed, my glibc headers are aliasing readdir to
readdir64 and truncate to truncate64 (and so on).
I'm then adding additional exports. Since I've no idea if the symbols where
always provided in the supported glibc's, I've added weak definitions too.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't use printk() where "current_thread_info()" is crap.
Until when we switch to running on init_stack, current_thread_info() evaluates
to crap. Printk uses "current" at times (in detail, ¤t is evaluated with
CONFIG_DEBUG_SPINLOCK to check the spinlock owner task).
And this leads to random segmentation faults.
Exactly, what happens is that ¤t = *(current_thread_info()), i.e. round
down $esp and dereference the value. I.e. access the stack below $esp, which
causes SIGSEGV on a VM_GROWSDOWN vma (see arch/i386/mm/fault.c).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's definition is wrong (-1 means "no limit" not 999),
only the Sparc SunOS/Solaris compat code uses it, so
let's just kill it off completely from limits.h and
all referencing code.
Noticed by Ulrich Drepper.
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a Kconfig symbol SPARC that is defined on both the sparc and
sparc64 architectures.
This symbol makes some dependencies more readable.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
It turns out that commit f9bd170a87
broke the cascade from XICS to i8259 on pSeries machines; specifically
we ended up not ever doing the EOI on the XICS for the cascade. The
result was that interrupts from the serial ports (and presumably any
other devices using ISA interrupts) didn't get through. This fixes
it and also simplifies the code, by doing the EOI on the XICS in the
xics_get_irq routine after reading and acking the interrupt on the
i8259.
Signed-off-by: Paul Mackerras <paulus@samba.org>
It was a stupid workaround for the "static inline" vs.
"extern inline" issues of long ago, and it is what causes
schedule() to be inlined like crazy into kernel/sched.c
when -Os is specified.
MIPS and S390 should probably do the same.
Now CC_OPTIMIZE_FOR_SIZE can be safely used on sparc64
once more.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now needs to include the type 1 functions ("direct") too.
Reported by Pavel Roskin <proski@gnu.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The CPM2 interrupt handler does not return success to the IRQ subsystem, which
causes it to kill the IRQ line after 100,000 interrupts.
Signed-off-by: Edson Seabra <Edson.Seabra@cyclades.com>
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since we don't restore the volatile registers in the syscall exit
path, we need to make sure we don't leak any potentially interesting
values from the kernel to userspace. This was already the case for
all except r11. This makes it use r11 for an MSR value, so r11 will
have an (uninteresting) MSR value in it on return to userspace.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Patch from Nicolas Pitre
Strictly speaking, the NPTL kernel helpers are required for pre ARMv6
only. They are available on ARMv6+ as well for obvious compatibility
reasons. However there are cases where extra memory barriers are needed
when using an SMP ARMv6 machine but not on pre-ARMv6.
This patch adds a memory barrier kernel helper that glibc can use as
needed for pre-ARMv6 binaries to be forward compatible with an SMP
kernel on ARMv6, as well as the necessary dmb instructions to the
cmpxchg helper.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Acked-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
UML skas0 stub has been miscompiling for many people (incidentally not
the authors), depending on the used GCC versions.
I think (and testing on some GCC versions shows) this patch avoids the
fundamental issue which is behind this, namely gcc using the stack when
we have just replaced it, behind gcc's back. The remapping and storage
of the return value is hidden in a blob of asm, hopefully giving gcc no
room for creativity.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
So you may have seen the miniconfig stuff wander by, which means that my
build script exits if there's a .config error, and we have this:
fs/Kconfig:1749:warning: 'select' used by config symbol 'CIFS_UPCALL'
refer to undefined symbol 'CONNECTOR'
This makes it shut up.
Signed-off-by: Rob Landley <rob@landley.net>
[ Verified it makes sense. ]
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
The current UML build assumes that on x86-64 systems, /lib is a symlink
to /lib64, but in some distributions (like PLD and CentOS) they are
separate directories, so the 64 bit library loader isn't found. This
patch inserts /lib64 at the start of the rpath on x86-64 UML builds.
Signed-off-by: Rob Landley <rob@landley.net>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Duplicated code - the patch adding it was probably applied twice without
enough care.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rather than providing more wrappers for 6-arg syscalls, arrange for
them to be supported as standard. This just means that we always
store the 6th argument on the stack, rather than in the wrappers.
This means we eliminate the wrappers for:
* sys_futex
* sys_arm_fadvise64_64
* sys_mbind
* sys_ipc
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
DMA_MODE_{READ,WRITE} are declared in asm-powerpc/dma.h and their
declarations there match the definitions. Old declarations in
ppc4xx_dma.h are not right anymore (wrong type, to start with).
Killed them, added include of asm/dma.h where needed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use correct address when referencing mmconfig aperture while checking
for broken MCFG. This was a typo when porting the code from 64bit to
32bit. It caused oopses at boot on some ThinkPads.
Should definitely go into 2.6.15.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sparc64, i386 and x86_64 have support for a special data section dedicated
to rarely updated data that is frequently read. The section was created to
avoid false sharing of those rarely read data with frequently written kernel
data.
This patch creates such a data section for ia64 and will group rarely written
data into this section.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Change the NR_CPUS default for ia64/sn up to 1024.
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: John Hesterberg <jh@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
I see why the problem exists only on SN. SN uses a different hardware
mechanism to purge TLB entries across nodes.
It looks like there is a bug in the SN TLB flushing code. During context switch,
kernel threads inherit the mm of the task that was previously running on the
cpu. This confuses the code in sn2_global_tlb_purge().
The result is a missed TLB purge for the task that owns the "borrowed" mm.
(I hit the problem running heavy stress where kswapd was purging code pages of
a user task that woke kswapd. The user task took a SIGILL fault trying to
execute code in the page that had been ripped out from underneath it).
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Use raw_smp_processor_id() instead of get_cpu() as we don't need the
extra features of get_cpu().
Signed-off-by: Jes Sorensen <jes@trained-monkey.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The udelay() inline for ia64 uses the ITC. If CONFIG_PREEMPT is enabled
and the platform has unsynchronized ITCs and the calling task migrates
to another CPU while doing the udelay loop, then the effective delay may
be too short or very, very long.
This patch disables preemption around 100 usec chunks of the overall
desired udelay time. This minimizes preemption-holdoffs.
udelay() is now too big to be inline, move it out of line and export it.
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Patch from Daniel Jacobowitz
Handle new EABI relocations when loading kernel modules. This is
necessary for CONFIG_AEABI kernels, and also for some broken
(since fixed) old ABI toolchains.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As reported by Keith Mannthey, there are problems in populate_memnodemap()
The bug was that the compute_hash_shift() was returning 31, with incorrect
initialization of memnodemap[]
To correct the bug, we must use (1UL << shift) instead of (1 << shift) to
avoid an integer overflow, and we must check that shift < 64 to avoid an
infinite loop.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On systems that do not support the HPET legacy functions (basically the IBM
x460, but there could be others), in time_init() we accidentally fall into a
PM timer conditional and set the vxtime_hz value to the PM timer's frequency.
We then use this value with the HPET for timekeeping.
This patch (which mimics the behavior in time_init_gtod) corrects the
collision.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When a register set is passed in don't try to fix up the pointer.
Noticed by Al Viro
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They report all busses as MMCONFIG capable, but it never works for the
internal devices in the CPU's builtin northbridge.
It just probes all func 0 devices on bus 0 (the internal northbridge is
currently always on bus 0) and if they are not accessible using MCFG they are
put into a special fallback bitmap.
On systems where it isn't we assume the BIOS vendor supplied correct MCFG.
Requires the earlier patch for mmconfig type1 fallback
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When there is no entry for a bus in MCFG fall back to type1. This is
especially important on K8 systems where always some devices can't be accessed
using mmconfig (in particular the builtin northbridge doesn't support it for
its own devices)
Cc: <gregkh@suse.de>
Cc: <jgarzik@pobox.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's illegal because it can sleep.
Use a two step lookup scheme instead. First look up the vm_struct, then
change the direct mapping, then finally unmap it. That's ok because nobody
can change the particular virtual address range as long as the vm_struct is
still in the global list.
Also added some LinuxDoc documentation to iounmap.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Disabling LAPIC timer isn't sufficient. In some situations, such as we
enabled NMI watchdog, there is still unexpected interrupt (such as NMI)
invoked in offline CPU. This also avoids offline CPU receives spurious
interrupt and anything similar.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: "Seth, Rohit" <rohit.seth@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Otherwise TSC->HPET fallback could see incorrect state and crash later.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With this fix, sparc links vmlinuz again using crosstool. Without this
fix, the final link fails missing several dozen dozen symbols, beginning
with:
kernel/built-in.o(.text+0x6fd0): In function `do_exit':
: undefined reference to `exit_io_context'
(exit_io_context is defined in block/ll_rw_blk.c).
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes one build error introduced in sparc with the patch of Oct 30,
resent Nov 4 "[patch 3/5] atomic: atomic_inc_not_zero" I still can't get
sparc to build, but at least it gets further after I remove this line.
Apparently, this change was agreed to by Andrew and Nick on Nov 14, but
everyone thought someone else was doing it.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I realized ZONE_DMA32 has a trivial bug at Kconfig for ia64. In
include/linux/gfp.h on 2.6.15-rc5-mm1, CONFIG is define like followings.
#ifdef CONFIG_DMA_IS_DMA32
#define __GFP_DMA32 ((__force gfp_t)0x01) /* ZONE_DMA is ZONE_DMA32
*/
:
:
So, CONFIG_"ZONE"_DMA_IS_DMA32 is clearly wrong.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When multiple probes are registered at the same address and if due to some
recursion (probe getting triggered within a probe handler), we skip calling
pre_handlers and just increment nmissed field.
The below patch make sure it walks the list for multiple probes case.
Without the below patch we get incorrect results of nmissed count for
multiple probe case.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Page count should be initialized to 1 on each of the MIPS empty zero pages,
to avoid a bad_page warning whenever one of them is freed from all mappings.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch/um/kernel/tt/uaccess.c: In function `copy_from_user_tt':
arch/um/kernel/tt/uaccess.c:11: error: `FIXADDR_USER_START' undeclared (first use in this function)
arch/um/kernel/tt/uaccess.c:11: error: (Each undeclared identifier is reported only once
arch/um/kernel/tt/uaccess.c:11: error: for each function it appears in.)
I get the compile error when I disable CONFIG_MODE_SKAS.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Paolo Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With CPU hotplug enabled, NMI watchdog stoped working. It appears the
violation is the cpu_online check in nmi handler. local ACPI based NMI
watchdog is initialized before we set CPU online for APs. It's quite
possible a NMI is fired before we set CPU online, and that's what happens
here.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Lothar Wassmann
The patch makes sure, that the ouptut functions of pins are restored
before restoring the Alternat Function settings, preventing pins from
being intermediately configured for undefined or unwanted alternate
functions.
Here is the original comment:
I've got a PXA270 system that uses GPIO80 as nCS4. This system did
hang on resume. Digging into the problem I found that the processor
stalled immediately when restoring the GAFR2_U register which restored
the alternate function for GPIO80. Since the GPDR registers were
restored after the GAFR registers, the offending GPIO was configured
as input at this point.
Thus the alternate function that was in effect after restoring the
GAFR was in fact the input function "MBREQ" instead of the output
function "nCS4". The "PXA27x Processor Family Developer's Manual"
(Footnote in Table 6-1 on page 6-3) states that:
"The MBREQ alternate function must not be enabled until the PSSR[RDH]
bit field is cleared. For more details, see Table 3-15, "PSSR Bit
Definitions" on page 3-71."
There is another note in the Developer's Manual (chapter 24.4.2
"GPIO operation as Alternate Function" on page 24-4)
stating that:
"Configuring a GPIO for an alternate function that is not defined for
it causes unpredictable results."
Since some GPIOs have no input function defined, and to prevent
inadvertedly programming the MBREQ function on some pin, the GAFR
registers should be restored after the GPDR registers have been
restored.
Additional provisions have to be made when the MBREQ function is
actually required. The corresponding GAFR bits should not be restored
with the regular GAFR restore, but must be set only after the PSSR
bits have been cleared.
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ppc32 kernel, when built with CONFIG_SMP and booted on a single CPU
machine, will not properly set smp_tb_synchronized, thus causing
gettimeofday() to not use the HW timebase and to be limited to jiffy
resolution. This, among others, causes unacceptable pauses when launching
X.org.
Signed-Off-By: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The code that sets the clock spreading feature of the Intrepid ASIC
must not be run on some machine models or those won't boot. This
fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Patch from Nikola Valerjev
Single stepping an application using ptrace() fails over ARM instructions BX and BLX.
Steps to reproduce:
Compile and link the following files
main.c
-----
void foo();
int main() {
foo();
return 0;
}
foo.s
-----
.text
.globl foo
foo:
BX LR
Using ptrace() functionality, run to main(), and start singlestepping.
Singlestep over \"BX LR\" instruction won\'t transfer the control back
to main, but run the code to completion.
This problems seems to be in the function get_branch_address() in
arch/arm/kernel/ptrace.c. The function doesn\'t seem to recognize BX
and BLX instructions as branches. BX and BLX instructions can be used
to convert from ARM to Thumb mode if the target address has the low
bit set. However, they are also perfectly legal in the ARM only mode.
Although other things in the kernel seem to indicate that only ARM
mode is accepted (and not Thumb), many compilers will generate BX
and BLX instructions even when generating ARM only code.
Signed-off-by: Nikola Valerjev <nikola@ghs.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On ppc64, when opening a new hugepage region, we need to make sure any
old normal-page SLBs for the area are flushed on all CPUs. There was
a bug in this logic - after putting the new hugepage area masks into
the thread structure, we copied it into the paca (read by the SLB miss
handler) only on one CPU, not on all. This could cause incorrect SLB
entries to be loaded when a multithreaded program was running
simultaneously on several CPUs. This patch corrects the error,
copying the context information into the PACA on all CPUs using the mm
in question before flushing any existing SLB entries.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On most powerpc CPUs, the dcache and icache are not coherent so
between writing and executing a page, the caches must be flushed.
Userspace programs assume pages given to them by the kernel are icache
clean, so we must do this flush between the kernel clearing a page and
it being mapped into userspace for execute. We were not doing this
for hugepages, this patch corrects the situation.
We use the same lazy mechanism as we use for normal pages, delaying
the flush until userspace actually attempts to execute from the page
in question.
Tested on G5.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cache info is setup by walking the device tree in initialize_cache_info().
However, icache_flush_range might be called before that, in
slb_initialize()->patch_slb_encoding, which modifies the load immediate
instructions used with SLB fault code.
Not only that, but depending on memory layout, we might take SLB faults
during unflatten_device_tree. So that fault will load an SLB entry that
might not contain the right LLP flags for the segment.
Either we can walk the flattened device tree to setup cache info, or
we can pick the known defaults that are known to work. Doing it in the
flattened device tree is hairier since we need to know the machine type
to know what property to look for, etc, etc.
For now, it's just easier to go with the defaults. Worst thing that
happens from it is that we might waste a few cycles doing too small
dcbst/icbi increments.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some debug code wasn't properly removed from the initial 64k pages
patch, and while it's harmless, it's also slowing down significantly a
very hot code path, thus it should really be removed.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 64k pages patch changed the meaning of one argument passed to the
low level hash functions (from "large" it became "psize" or page size
index), but one of the call sites wasn't properly updated, causing
potential random weird problems with huge pages. This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This bug exists in the current code and prevents machines from booting
with numa enabled if there is a node that does not contain memory.
Workaround is to boot with 'numa=off'. Looks like a simple typo.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
What is the value shown in "cpu MHz" of /proc/cpuinfo when CPUs are capable of
changing frequency?
Today the answer is: It depends.
On i386:
SMP kernel - It is always the boot frequency
UP kernel - Scales with the frequency change and shows that was last set.
On x86_64:
There is one single variable cpu_khz that gets written by all the CPUs. So,
the frequency set by last CPU will be seen on /proc/cpuinfo of all the
CPUs in the system. What you see also depends on whether you have constant_tsc
capable CPU or not.
On ia64:
It is always boot time frequency of a particular CPU that gets displayed.
The patch below changes this to:
Show the last known frequency of the particular CPU, when cpufreq is present. If
cpu doesnot support changing of frequency through cpufreq, then boot frequency
will be shown. The patch affects i386, x86_64 and ia64 architectures.
Signed-off-by: Venkatesh Pallipadi<venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
This patch moves away PMBASE reading and only performs it at
cpufreq_register_driver time by exiting with -ENODEV if unable to read
the value.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
The attached patch introduces runtime latency measurement for ICH[234]
based chipsets instead of using CPUFREQ_ETERNAL. It includes
some sanity checks in case the measured value is out of range and
assigns a safe value of 500uSec that should still be enough on
problematics chipsets (current testing report values ~200uSec). The
measurement is currently done in speedstep_get_freqs in order to avoid
further unnecessary transitions and in the hope it'll come handy for SMI
also.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
speedstep-ich.c | 4 ++--
speedstep-lib.c | 32 +++++++++++++++++++++++++++++++-
speedstep-lib.h | 1 +
speedstep-smi.c | 1 +
4 files changed, 35 insertions(+), 3 deletions(-)
If a user has booted with 'quiet', some important messages don't
get displayed which really should. We've seen at least one case
where powernow-k8 stopped working, and the user needed a BIOS update
that they didn't know about.
Signed-off-by: Dave Jones <davej@redhat.com>
The patch that added support for a new platform chipset (shub2) broke
PTC deadlock recovery on older versions of the chipset. (PTCs are the
SN platform-specific method for doing a global TLB purge). This
patch fixes deadlock recovery so that it works on both the old & new
chipsets.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
We have a customer application which trips a bug. The problem arises
when a driver attempts to call do_munmap on an area which is mapped, but
because current->thread.task_size has been set to 0xC0000000, the call
to do_munmap fails thinking it is an unmap beyond the user's address
space.
The comment in fs/binfmt_elf.c in load_elf_library() before the call
to SET_PERSONALITY() indicates that task_size must not be changed for
the running application until flush_thread, but is for ia64 executing
ia32 binaries.
This patch moves the setting of task_size from SET_PERSONALITY() to
flush_thread() as indicated. The customer application no longer is able
to trip the bug.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The per-node data structures are allocated with strided offsets that are a
function of the node number. This prevents excessive cache-aliasing from
occurring.
On systems with a large number of nodes, the strided offset becomes
too large. This patch restricts the maximum offset to 32MB. This is far larger
than the size of any current L3 cache.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Altix only patch to add fixup code that sets up
pci_controller->window. This code is a temporary
fix until ACPI support on Altix is added.
Also, corrects the usage of pci_dev->sysdata,
which had previously been used to reference
platform specific device info, to now point to
a pci_controller struct.
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Return -EINTR instead of -ERESTARTSYS when signals are delivered during
a blocked read of /proc/sal/*/event. This allows salinfo_decode to
detect signals when it is blocked on a read of those files.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
There's never been a hardware platform that has both pSeries/RPA LPAR
hypervisor and stab (pre-POWER4 segment management). This removes
the redundant code in stab_initalize().
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reverts commit da0825fd20, making
it so that if you select CONFIG_PPC_MULTIPLATFORM you get support
for PMAC, PREP and CHRP built in.
The reason for not allowing PMAC, PREP and CHRP to be selected
individually for ARCH=ppc is that there is too much interdependency
between them in the platform support code. For example, CHRP uses
the PMAC nvram code.
Configuring with ARCH=powerpc does allow you to select support for
PMAC and CHRP separately. Support for PREP is not there yet but
should be there soon.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The previous commit will use the page-at-a-time hypervisor call for
setting up IOMMU entries when we are using 64k pages and setting up
one 64k page, even though that means 16 calls to the hypervisor, since
the hypervisor still works on 4k pages. This optimizes this case by
using the multi-page IOMMU setup hypervisor call instead.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This updates the sn2_defconfig file for the Altix 330 hardware, enables
the AGP graphics for the SGI Prism, and removes prompts for the remainder
of the new features. Greg Edwards reviewed the changes.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Greg Edwards <edwardsg@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Must adjust tcenum and npages by TCE_PAGE_FACTOR to convert between
64KB pages and TCE (4K) pages. (This is done in other places, except
for this one location.)
Signed-off-by: Michal Ostrowski <mostrows at watson ibm com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Correctly specify treeboot based image entrypoint. Currently makefile uses
$(ENTRYPOINT) which isn't defined anywhere. Each board port sets
entrypoint-$(CONFIG_BOARD_NAME) instead.
Without this patch I cannot boot Ocotea (PPC440GX eval board) anymore. I
was getting random "OS panic" errors from OpenBIOS for a while, but with
current kernel I get them all the time (probably because image became
bigger).
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Acked-by: Tom Rini <trini@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The time to wait after deasserting PCI_RST has been counted with incorrect
value - this patch fixes the issue.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Richard Purdie
Akita requires inbuilt kernel i2c support for its GPIOs. Add this
requirement to Kconfig and update the defconfig to match.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is a typo in the ARM IXDP425 setup definition that mistakenly tries
to use UART1's IRQ for UART2's traffic.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fixes BCSR accesses in the board setup/reset code. The registers are
actually 16-bit, and their addresses are different between DBAu1550 and
other DBAu1xx0 boards.
From Sergei Shtylylov <sshtylyov@ru.mvista.com>.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The rdhwr emulation accidentally swallowed the SIGILL from most other
illegal instructions. Make sure to return -EFAULT by default.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
o Check if IRQ is disabled or in progress before reenabling interrupts
in jmr3927_irq_end..
o s/spinlock_irqsave/spin_lock_irqsave/
o s/spinlock_irqrestore/spin_unlock_irqrestore/
o Flush write buffer after setting IRQ mask
o In 2.6 jmr3927_ioc_interrupt interrupt handlers return irqreturn_t
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Thanks to LinuxICC (http://linuxicc.sf.net), a comparison of a u32 less
than 0 was found, this patch changes the variable to a signed int so that
comparison is meaningful.
Signed-off-by: Gabriel A. Devenyi <ace@staticwave.ca>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Lazy flush_dcache_page() causes userspace instability on SMP
platforms, so disable it for now.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Setting irq affinity stops working when MSI is enabled. With MSI, move_irq
is empty, so we can't change irq affinity. It appears a typo in Ashok's
original commit for this issue. X86_64 actually is using move_native_irq.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I recently discovered a bug on PPC which causes the floating point
registers to get corrupted when CONFIG_PREEMPT=y.
The problem occurred while running a multi threaded Java application that
does floating point. The problem could be reproduced in anywhere from 2 to
6 hours. With the patch I have included below it ran for over a week
without failure.
Signed-off-by: Paolo Galtieri <pgaltieri@mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Tom Rini <trini@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Anne NICOLAS <anne.nicolas@mandriva.com> and Andres Kaaber
<andres.kaaber@rescue.ee> reported their HP laptop didn't reboot smoothly.
Signed-off-by: Thierry Vignaud <tvignaud@mandriva.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the correct pointer to clear the memory of the return values,
to prevent stack corruption in the callers stackframe.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a bug noticed by Paolo Galtieri and fixed for ARCH=ppc in
the previous commit (ppc: fix floating point register corruption).
This fixes the arch/powerpc code by adding preempt_disable/enable,
and also cleans it up a bit by pulling out the code that discards
any lazily-switched CPU register state into a new function, rather
than having that code repeated in three places.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Vivek Goyal
Sylvain Munaut