If CONFIG_BUG is not enabled, BUG() does not stop the execution. Many
places in code expect the execution to stop, and this causes compiler
warnings about uninitialized variables and returning from a non-void
function without a return value.
This patch fixes the warnings by initializing the variables and
returning properly after BUG() lines. However, the behaviour is still
undefined after the BUG, but this is the choice the user makes when
using CONFIG_BUG=n.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapfb_parse_vram_param()'s check for end pointer returned from
simple_strtoul() is wrong, causing the code to bug if the second or
later vram parameters are non-parseable, for example
"omapfb.vram=0:2M,:5M".
However, even in that case the code will most likely bail out with
-EINVAL in the following checks, so the bug is probably not a fatal one.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Hein Tibosch <hein_tibosch@yahoo.es>
Currently when multiple overlays are active, OMAPFB_SETUP_PLANE fails.
Instead of failing, allow it to configure the first overlay as if there
was only one overlay, the remaining ones will have to be configured in
other ways (sysfs).
This allows overlay-controlling programs (like video players) to function
properly when framebuffer is cloned to another display (like TV).
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If the size of memory region that is being set up is the same as before,
we don't have to do memory and layer busy checks.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapfb driver used platform_data to get fb memory areas and formats
defined by the board file.
This patch removes omapfb's (both old and new omapfb) use of the
memory data in platform_data, because:
- No board uses them currently
- It's not board file's job to define things like amount of default
framebuffer memory. These should come from the bootloader via command
line parameters.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP SRAM can be used as video memory on OMAP1 and 2. However, there
usually is very little SRAM available, thus limiting its use, and no
board supported by the kernel currently uses it.
This patch removes the use of SRAM as video ram for the omapdss driver
to simplify memory handling.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
* 'fbdev-next' of git://github.com/schandinat/linux-2.6: (175 commits)
module_param: make bool parameters really bool (drivers/video/i810)
Revert "atmel_lcdfb: Adjust HFP calculation so it matches the manual."
OMAPDSS: HDMI: Disable DDC internal pull up
OMAPDSS: HDMI: Move duplicate code from boardfile
OMAPDSS: add OrtusTech COM43H4M10XTC display support
OMAP: DSS2: Support for UMSH-8173MD TFT panel
ASoC: OMAP: HDMI: Move HDMI codec trigger function to generic HDMI driver
OMAPDSS: HDMI: Create function to enable HDMI audio
ASoC: OMAP: HDMI: Correct signature of ASoC functions
ASoC: OMAP: HDMI: Introduce driver data for audio codec
grvga: fix section mismatch warnings
video: s3c-fb: Don't keep device runtime active when open
video: s3c-fb: Hold runtime PM references when touching registers
video: s3c-fb: Take a runtime PM reference when unblanked
video: s3c-fb: Disable runtime PM in error paths from probe
video: s3c-fb: Use s3c_fb_enable() to enable the framebuffer
video: s3c-fb: Make runtime PM functional again
drivers/video: fsl-diu-fb: merge fsl_diu_alloc() into map_video_memory()
drivers/video: fsl-diu-fb: add default platform ops functions
drivers/video: fsl-diu-fb: remove broken reference count enabling the display
...
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
struct omap_overlayr contains info and info_dirty fields, both of which
should be internal to apply.c.
This patch moves those fields into ovl_priv data, and names them
user_info and user_info_dirty.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Overlays are currently enabled and disabled with a boolean in the struct
omap_overlay_info. The overlay info is set with ovl->set_overlay_info(),
and made into use with mgr->apply().
This doesn't work properly, as the enable/disable status may affect also
other overlays, for example when using fifo-merge. Thus the enabling and
disabling of the overlay needs to be done outside the normal overlay
configuration.
This patch achieves that by doing the following things:
1) Add function pointers to struct omap_overlay: enable(), disable() and
is_enabled(). These are used to do the obvious. The functions may block.
2) Move the "enabled" field from struct omap_overlay to ovl_priv_data.
3) Add a new route for settings to be applied to the HW, called
"extra_info". The status of the normal info and extra_info are tracked
separately.
The point here is to allow the normal info to be changed and
applied in non-blocking matter, whereas the extra_info can only be
changed when holding the mutex. This makes it possible to, for example,
set the overlay enable flag, apply it, and wait until the HW has taken
the flag into use.
This is not possible if the enable flag would be in the normal info, as
a new value for the flag could be set at any time from the users of
omapdss.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
A DRM display driver for TI OMAP platform. Similar to omapfb (fbdev)
and omap_vout (v4l2 display) drivers in the past, this driver uses the
DSS2 driver to access the display hardware, including support for
HDMI, DVI, and various types of LCD panels. And it implements GEM
support for buffer allocation (for KMS as well as offscreen buffers
used by the xf86-video-omap userspace xorg driver).
The driver maps CRTCs to overlays, encoders to overlay-managers, and
connectors to dssdev's. Note that this arrangement might change slightly
when support for drm_plane overlays is added.
For GEM support, non-scanout buffers are using the shmem backed pages
provided by GEM core (In drm_gem_object_init()). In the case of scanout
buffers, which need to be physically contiguous, those are allocated
with CMA and use drm_gem_private_object_init().
See userspace xorg driver:
git://github.com/robclark/xf86-video-omap.git
Refer to this link for CMA (Continuous Memory Allocator):
http://lkml.org/lkml/2011/8/19/302
Links to previous versions of the patch:
v1: http://lwn.net/Articles/458137/
v2: http://patches.linaro.org/4156/
v3: http://patches.linaro.org/4688/
v4: http://patches.linaro.org/4791/
History:
v5: move headers from include/drm at Greg KH's request, minor rebasing
on 3.2-rc1, pull in private copies of drm_gem_{get,put}_pages()
because "drm/gem: add functions to get/put pages" patch is not
merged yet
v4: bit of rework of encoder/connector _dpms() code, modeset_init()
rework to not use nested functions, update TODO.txt
v3: minor cleanups, improved error handling for dev_load(), some minor
API changes that will be needed later for tiled buffer support
v2: replace omap_vram with CMA for scanout buffer allocation, remove
unneeded functions, use dma_addr_t for physical addresses, error
handling cleanup, refactor attach/detach pages into common drm
functions, split non-userspace-facing API into omap_priv.h, remove
plugin API
v1: original
Signed-off-by: Rob Clark <rob@ti.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With module.h being implicitly everywhere via device.h, the absence
of explicitly including something for EXPORT_SYMBOL went unnoticed.
Since we are heading to fix things up and clean module.h from the
device.h file, we need to explicitly include these files now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
overlay_info struct, used to configure overlays, currently includes both
physical and virtual addresses for the pixels. The vaddr was added to
support more exotic configurations where CPU would be used to update a
display, but it is not currently used and there has been no interest in
the feature. Using CPU to update a screen is also less interesting now
that OMAP4 has two LCD outputs.
This patch removes the vaddr field, and modifies the users of omapdss
accordingly. This makes the use of omapdss a bit simpler, as the user
doesn't need to think if it needs to give the vaddr.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the new read_edid() function to get EDID information from the
display (when available), and use the information to use a suitable mode
at initialization time.
Hot-plug is not yet supported, so the timings selected at init time will
stay even if the monitor would be changed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSS driver has not been "experimental" for many years now, so perhaps
it's time to remove the text from Kconfig titles.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently omapfb wants that all the display devices have a driver,
otherwise omapfb refuses to start. There's no real requirement to act
like that, and this patch will make omapfb give a warning and skip that
device.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Make the debug message useful by printing the name of the device
that no associated driver could be found for.
Signed-off-by: Andy Doan <andy.doan@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Implement auto-update mode for manual-update displays. omapfb driver
uses a delayed work to update the display with a constant rate.
The update mode can be changed via OMAPFB_SET_UPDATE_MODE ioctl, which
previously called omapdss but is now handled inside omapfb, and a new
sysfs file, "update_mode".
The update interval is by default 20 times per second, but can be
changed via "auto_update_freq" module parameter. There is also a new
module parameter "auto_update", which will make omapfb start manual
update displays in auto-update mode.
This auto-update mode can be used for testing if the userspace does not
support manual update displays properly. However, it is a very
inefficient solution, and should be considered more as a hack for
testing than something that could be used as a long term solution.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Create a new struct omapfb_display_data to contain omapfb's private
per-display data. Move the bpp override there.
This struct will be used to hold auto/manual update state of a display
in the following patches.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapfb_mode_to_timings() had struct fb_info, struct fb_var and struct
fb_ops allocated from stack. This caused the stack usage grow quite
high.
Use kzalloc to allocate the structs instead.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When DBG() is used in a simple if-else, the resulting code path
currently depends on the definition of DBG(). Inserting the statement in
a "do { ... } while (0)" prevents this possible misuse.
Signed-off-by: Niels de Vos <ndevos@redhat.com>
[tomi.valkeinen@ti.com: changed the title of the commit msg]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Convert simple/strict_strto* functions to kstrto* functions. Only simple
cases are converted.
simple_strto* uses are still left to places where it is used to parse
numbers from a list of numbers. These need some other solution than
kstrto*.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently omapfb does an implicit display update (for manual update
displays) on unblank.
There is no guarantee that the framebuffer contains a valid image when
unblank is called. When using manual update displays it is the
responsibility of the user space to update the display, and so it should
be in this case also.
This patch removes the implicit display update on unblank.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
[tomi.valkeinen@ti.com: improved description]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Errors from the panel driver were ignored during panel initialization.
Handle the errors and fail accordingly.
Also move the display initialization to a separate function to make it
cleaner.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add get_dimensions() to struct omap_dss_driver. Use the call, if supported
by the driver, in OMAPFB.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
arch/arm/plat-omap/include/plat/display.h is an include for the OMAP DSS
driver. A more logical place for it is in include/video.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When omapfb.mode is passed through bootargs, when omapfb is setting mode,
it would check if timings passed are fine for panel attached to it.
It makes use of check_timing API provided by the panel.
In current code if check_timing API is not available for attached panel,
OMAPFB would return -EINVAL and BPP sent via bootargs will not have any effect.
In case of panels like TAAL panel, omapfb or any other driver should not be allowed to
change the timings. So bpps sent via bootargs will not have an effect.
In such case we can check only the x_res and y_res with the panels resolution
and if they match go ahead and set the bpps.
The bpp value sent via bootarg would have an effect.
Signed-off-by: Mayuresh Janorkar <mayur@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
A null pointer check added. And using kstrdup()
instead of kmalloc() & strcpy()
Signed-off-by: Samreen <samreen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
VRFB is supported only on OMAP2 and OMAP3 platforms. If VRFB rotation is
not supported by the hardware and the user requests VRFB rotation,
print a warning and ignore the request from the user.
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
config VRFB should depend on ARCH_OMAP2 or ARCH_OMAP3.
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Framebuffer's left and right margins are relative to the active pixel
area. Front and back porches are relative to the sync area.
Left margin was wrongly assigned to front porch (and right to back),
this patch fixes it.
Signed-off-by: tasskjapp@gmail.com
Reviewed-by: Russ.Dill@gmail.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
FBIO_WAITFORVSYNC is a stardard ioctl for waiting vsync, already
used by some userspace, so add it as an alias for OMAPFB_WAITFORVSYNC.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
omapfb_mode_to_timings() sets the bpp to 0 when bootarg omapfb.mode is set to
either "pal" or "ntsc". This patch corrects this by setting the bpp to 24, as
would be done if omapdss_default_get_recommended_bpp() would be called.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move sysfs entry creation to omapfb_probe() from omapfb_create_framebuffers().
This will make sure that sysfs entry is not left behind in case of unsuccessful
probe due to failure in enabling fb0 of omapfb_create_framebuffers().
Signed-off-by: Afzal Mohammed <lazfamam@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Using bool silently converted input to 0 or 1, making the range check
useless. Use unsigned long instead, and convert to bool later. Found by
Coverity.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Unsigned regno can never be less than zero. Found by Coverity.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Unsigned rotate can never be less than zero. Found by Coverity.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Make sure NULL return value of fb2display() is not referenced. Found by
Coverity.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Trigger WARN_ON() messages from various places in the code in case the
memory region is not currently locked.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
When more than one memory region needs to be lockd at the same time use
the memory region id to fix the order in which the locks are taken. Also
one needs to use the _nested() versions of the locking primitives. The
memory region id can serve as the lock class there as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
R/W semaphore is a good fit for the memory region locking pattern.
So use it.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Add locking to the memory regions to make sure the memory region size
won't be changed while some other piece of code is performing some
checks or setup based on that information.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Separate the memory region from the framebuffer device a little bit.
It's now possible to select the memory region used by the framebuffer
device using the new mem_idx parameter of omapfb_plane_info. If the
mem_idx is specified it will be interpreted as an index into the
memory regions array, if it's not specified the framebuffer's index is
used instead. So by default each framebuffer keeps using it's own
memory region which preserves backwards compatibility.
This allows cloning the same memory region to several overlays and yet
each overlay can be controlled independently since they can be
associated with separate framebuffer devices.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
In omapfb_enable_overlay() if the overlay state is already what we want
skip the set_overlay_info().
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
If video memory hasn't been allocate have check_fb_var() still check
most of the settings, just skip the ones involving the size of the
memory region. Also skip the memory address calculations in
omapfb_setup_overlay() if there's no memory.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Tomi Valkeinen