On x86, __acpi_map_table uses early_ioremap() to create the mapping,
replacing the previous mapping with a new one. Once enough of the
kernel is up an running it switches to using normal ioremap(). At
that point, we need to clean up the final mapping to avoid a warning
from the early_ioremap subsystem.
This can be removed after all the instances in the ACPI code are fixed
that rely on early-ioremap's implicit overmapping of previously
mapped tables.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
During early boot, ACPI RSDT/XSDT table entries are gathered into the
'initial_tables[]' array. This array is currently statically defined (see
./drivers/acpi/tables.c). When there are more table entries than can be
held in the 'initial_tables[]' array, the message "Truncating N table
entries!" is output. As currently implemented, this message will always
erroneously calculate N as 0.
This patch fixes the calculation that determines how many table entries
will be missing (truncated).
This modification may be used under either the GPL or the BSD-style
license used for Intel ACPI CA code.
Signed-off-by: Myron Stowe <myron.stowe@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
According to kerneljanitors todo list all printk calls (beginning
a new line) should have an according KERN_* constant.
Those are the missing peaces here for the acpi subsystem.
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Some devices trigger a DEVICE_CHECK on every evalutation of _STA. This
can also be seen in commit 8b59560a3b
(ACPI: dock: avoid check _STA method). If an undock is processed, the
dock driver sends a uevent and userspace might read the show_docked
property in sysfs. This causes an evaluation of _STA of the particular
device which causes the dock driver to immediately dock again.
In any case, evaluation of _STA (show_docked) does not necessarily mean
that we are docked, so check with the internal device structure.
http://bugzilla.kernel.org/show_bug.cgi?id=12360
Signed-off-by: Holger Macht <hmacht@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
When ACPI is disabled in the BIOS of this VIA C3 box,
it invalidates the RSDP, which Linux notices:
ACPI Error (tbxfroot-0218): A valid RSDP was not found [20080926]
Bug Linux neglected to disable ACPI at that stage,
and later scribbled on smp_found_config:
ACPI: No APIC-table, disabling MPS
But this box doesn't run well in legacy PIC mode,
it needed IOAPIC mode to perform correctly:
http://lkml.org/lkml/2009/2/5/39
So exit ACPI mode cleanly when we first detect
that it is hopeless.
Signed-off-by: Len Brown <len.brown@intel.com>
CPU_IDLE=y has been default for ACPI=y since Nov-2007,
and has shipped in many distributions since then.
Here we delete the CPU_IDLE=n ACPI idle code, since
nobody should be using it, and we don't want to
maintain two versions.
Signed-off-by: Len Brown <len.brown@intel.com>
Currently, netlink_broadcast() reports errors to the caller if no
messages at all were delivered:
1) If, at least, one message has been delivered correctly, returns 0.
2) Otherwise, if no messages at all were delivered due to skb_clone()
failure, return -ENOBUFS.
3) Otherwise, if there are no listeners, return -ESRCH.
With this patch, the caller knows if the delivery of any of the
messages to the listeners have failed:
1) If it fails to deliver any message (for whatever reason), return
-ENOBUFS.
2) Otherwise, if all messages were delivered OK, returns 0.
3) Otherwise, if no listeners, return -ESRCH.
In the current ctnetlink code and in Netfilter in general, we can add
reliable logging and connection tracking event delivery by dropping the
packets whose events were not successfully delivered over Netlink. Of
course, this option would be settable via /proc as this approach reduces
performance (in terms of filtered connections per seconds by a stateful
firewall) but providing reliable logging and event delivery (for
conntrackd) in return.
This patch also changes some clients of netlink_broadcast() that
may report ENOBUFS errors via printk. This error handling is not
of any help. Instead, the userspace daemons that are listening to
those netlink messages should resync themselves with the kernel-side
if they hit ENOBUFS.
BTW, netlink_broadcast() clients include those that call
cn_netlink_send(), nlmsg_multicast() and genlmsg_multicast() since they
internally call netlink_broadcast() and return its error value.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
They were long enough set deprecated...
Update Documentation/cpu-freq/users-guide.txt:
The deprecated files listed there seen not to exist for some time anymore
already.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPICA exports acpi_os_validate_address() so the OS
can prevent BIOS AML from accessing specified addresses.
Start using this interface to prevent AML from accessing
some well known IO addresses that the OS "owns".
Signed-off-by: Len Brown <len.brown@intel.com>
on boot, print out the OSI strings the BIOS uses to query the OS.
To see this output...
build with CONFIG_ACPI_DEBUG
boot with
"acpi.debug_level=4" (ACPI_LV_INFO) (enabled by default)
and
"acpi.debug_level=1" (ACPI_UTILITIES) (default is 0)
example output:
ACPI: BIOS _OSI(Windows 2001) supported
ACPI: BIOS _OSI(Windows 2001 SP1) supported
ACPI: BIOS _OSI(Windows 2001 SP2) supported
ACPI: BIOS _OSI(Windows 2006) supported
ACPI: BIOS _OSI(Linux) not-supported
ACPI: BIOS _OSI(FreeBSD) not-supported
Signed-off-by: Len Brown <len.brown@intel.com>
According to the Spec the first two elements in the _BCL package won't be
regarded as the available brightness level. The first is the brightness when
full power is connected to the box(It means that the AC adapter is plugged).
The second is the brightness level when the box is on battery.
If the first two elements are still used while finding the next brightness
level, it will fall back to the lowest level when keeping on pressing
hotkey. (On some boxes the brightness will be changed twice when hotkey is
pressed once. One is in the ACPI video driver. The other is changed by sys I/F.
In the ACPI video driver the first two elements will be used while changing
the brightness. But the first two elements is skipped while using sys I/F.
In such case there exists the inconsistency).
So he first two elements had better be skipped while showing the available
brightness or finding the next brightness level.
http://bugzilla.kernel.org/show_bug.cgi?id=12450
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
It is true that BM_RLD needs to be set to enable
bus master activity to wake an older chipset (eg PIIX4) from C3.
This is contrary to the erroneous wording the ACPI 2.0, 3.0
specifications that suggests that BM_RLD is an indicator
rather than a control bit.
ACPI 1.0's correct wording should be restored in ACPI 4.0:
http://www.acpica.org/bugzilla/show_bug.cgi?id=689
But the kernel should not have to clear BM_RLD
when entering a non C3-type state just to set
it again when entering a C3-type C-state.
We should be able to set BM_RLD at boot time
and leave it alone -- removing the overhead of
accessing this IO register from the idle entry path.
Signed-off-by: Len Brown <len.brown@intel.com>
PM1a_STS and PM1b_STS are twins that get OR'd together
on reads, and all writes are repeated to both.
The fields in PM1x_STS are single bits only,
there are no multi-bit fields.
So it is not necessary to lock PM1x_STS reads against
writes because it is impossible to read an intermediate
value of a single bit. It will either be 0 or 1,
even if a write is in progress during the read.
Reads are asynchronous to writes no matter if a lock
is used or not.
Signed-off-by: Len Brown <len.brown@intel.com>
This patch fixes the crash I experienced in 2.6.29-rc2.
Tested on ASUS M50vm.
Signed-off-by: Tero Roponen <tero.roponen@gmail.com>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix two compilation warnings in drivers/acpi/sleep.c, one triggered
by unsetting CONFIG_SUSPEND and the other triggered by unsetting
CONFIG_HIBERNATION, by moving some code under the appropriate
#ifdefs .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Conflicts:
drivers/acpi/pci_irq.c
Note that this merge disables
e1d3a90846
pci, acpi: reroute PCI interrupt to legacy boot interrupt equivalent
Signed-off-by: Len Brown <len.brown@intel.com>
when CONFIG_RTC_DRV_CMOS=m
and thus !defined(HAVE_ACPI_LEGACY_ALARM)
drivers/acpi/proc.c:85: warning: ‘cmos_bcd_read’ declared ‘static’ but
never defined
Signed-off-by: Len Brown <len.brown@intel.com>
On some boxes there exist both RSDT and XSDT table. But unfortunately
sometimes there exists the following error when XSDT table is used:
a. 32/64X address mismatch
b. The 32/64X FACS address mismatch
In such case the boot option of "acpi=rsdt" is provided so that
RSDT is tried instead of XSDT table when the system can't work well.
http://bugzilla.kernel.org/show_bug.cgi?id=8246
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
cc:Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI_USE_LOCAL_CACHE will never be defined by the Linux kernel,
and thus utcache.c will always be dead code.
Signed-off-by: Len Brown <len.brown@intel.com>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (98 commits)
PCI PM: Put PM callbacks in the order of execution
PCI PM: Run default PM callbacks for all devices using new framework
PCI PM: Register power state of devices during initialization
PCI PM: Call pci_fixup_device from legacy routines
PCI PM: Rearrange code in pci-driver.c
PCI PM: Avoid touching devices behind bridges in unknown state
PCI PM: Move pci_has_legacy_pm_support
PCI PM: Power-manage devices without drivers during suspend-resume
PCI PM: Add suspend counterpart of pci_reenable_device
PCI PM: Fix poweroff and restore callbacks
PCI: Use msleep instead of cpu_relax during ASPM link retraining
PCI: PCIe portdrv: Add kerneldoc comments to remining core funtions
PCI: PCIe portdrv: Rearrange code so that related things are together
PCI: PCIe portdrv: Fix suspend and resume of PCI Express port services
PCI: PCIe portdrv: Add kerneldoc comments to some core functions
x86/PCI: Do not use interrupt links for devices using MSI-X
net: sfc: Use pci_clear_master() to disable bus mastering
PCI: Add pci_clear_master() as opposite of pci_set_master()
PCI hotplug: remove redundant test in cpq hotplug
PCI: pciehp: cleanup register and field definitions
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
The _OSC capability OSC_MSI_SUPPORT is set when the root bridge is added
with pci_acpi_osc_support(), so we no longer need to do it in the PCI
MSI driver. Also adds the function pci_msi_enabled, which returns true
if pci=nomsi is not on the kernel command-line.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The _OSC capabilities OSC_ACTIVE_STATE_PWR_SUPPORT and
OSC_CLOCK_PWR_CAPABILITY_SUPPORT are set when the root bridge is added
with pci_acpi_osc_support(), so we no longer need to do it in the ASPM
driver. Also add the function pcie_aspm_enabled, which returns true if
pcie_aspm=off is not on the kernel command-line.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The _OSC capability OSC_EXT_PCI_CONFIG_SUPPORT is set when the root
bridge is added with pci_acpi_osc_support() if we can access PCI
extended config space.
This adds the function pci_ext_cfg_avail which returns true if we can
access PCI extended config space (offset greater than 0xff). It
currently only returns false if arch=x86 and raw_pci_ext_ops is not set
(which might happen if pci=nommcfg is set on the kernel command-line).
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add pci_acpi_osc_support() and call it when a PCI bridge is added. This
allows us to avoid having every individual PCI root bridge driver call
_OSC support for every root bridge in their probe functions, a
significant savings in boot time.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
While looking at reducing the amount of architecture namespace pollution
in the generic kernel, I found that asm/irq.h is included in the vast
majority of compilations on ARM (around 650 files.)
Since asm/irq.h includes a sub-architecture include file on ARM, this
causes a negative impact on the ccache's ability to re-use the build
results from other sub-architectures, so we have a desire to reduce the
dependencies on asm/irq.h.
It turns out that a major cause of this is the needless include of
linux/hardirq.h into asm-generic/local.h. The patch below removes this
include, resulting in some 250 to 300 files (around half) of the kernel
then omitting asm/irq.h.
My test builds still succeed, provided two ARM files are fixed
(arch/arm/kernel/traps.c and arch/arm/mm/fault.c) - so there may be
negative impacts for this on other architectures.
Note that x86 does not include asm/irq.h nor linux/hardirq.h in its
asm/local.h, so this patch can be viewed as bringing the generic version
into line with the x86 version.
[kosaki.motohiro@jp.fujitsu.com: add #include <linux/irqflags.h> to acpi/processor_idle.c]
[adobriyan@gmail.com: fix sparc64]
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix misspelling of "firmware" in acpi_memhotplug.c
It's spelled "firmware".
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It is always "an" if there is a vowel _spoken_ (not written).
So it is:
"an hour" (spoken vowel)
but
"a uniform" (spoken 'j')
Signed-off-by: Frederik Schwarzer <schwarzerf@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Impact: Reduce memory usage, use new API.
This is part of an effort to reduce structure sizes for machines
configured with large NR_CPUS. cpumask_t gets replaced by
cpumask_var_t, which is either struct cpumask[1] (small NR_CPUS) or
struct cpumask * (large NR_CPUS).
(Changes to powernow-k* by <travis>.)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Update all messages so they look consistent.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This returns the FADT support to the original behavior, which is
to use default register widths. However, now check each register
definition and report a warning if it differs from the default.
This is a first step to moving away from the default widths,
rather than outright believing the widths in all FADTs for all
machines, considered rather dangerous until more data is obtained.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
1) Update the register lengths for the PM1 event blocks. The
length must be divided by two in order to use these to access
the status registers.
2) Add run-time option to use default register lengths to override a
faulty FADT.
3) Add warning message if any of the X64 address structures contain a length
that does not match the legacy length earlier in the FADT.
4) Move all FADT warning messages into the ValidateFadt function.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi.h now includes only the "public" acpica headers. All other
acpica headers are "private" and should not be included by acpica
users. One new file, accommon.h is used to include the commonly
used private headers for acpica code generation. Future plans
are to move all private headers to a new subdirectory.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
External driver files should not include any private acpica headers.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Uses the FADT-defined reset register and reset value. Checks the
FADT flags for the reset register supported bit. Supports reset
register in memory or I/O space, but not in PCI config space
since the host has the information to do it.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Move public interfaces from hwregs.c to new file, hwxface.c -
similar to the structure of the other ACPICA components.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Changed the acpi_hw_low_level_read and acpi_hw_low_level_write functions to
the public acpi_read and acpi_write to allow direct access to
ACPI registers. Removed the "width" parameter since the width
can be obtained from the input GAS structure. Updated the FADT
initialization to setup the GAS structures with the proper
widths. Some widths are still hardcoded because many FADTs have
incorrect register lengths.
Signed-off-by: Bob Moore <robert.moore@intel.com
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_ut_get_node_name is an internal acpica function.
use acpi_get_name to get node ascii name
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Avoid using internal functions: acpi_hw_disable_all_gpes and acpi_hw_enable_all_runtime_gpes
Use new public GPE group enable/disable interfaces: acpi_disable_all_gpes and acpi_enable_all_runtime_gpes
Also avoid using internal symbol ACPI_TABLE_INDEX_FACS, call acpi_get_table.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Added acpi_disable_all_gpes and acpi_enable_all_runtime_gpes for
public use.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This function maps an input GPE index to a GPE block device. Also
Added acpi_current_gpe_count to track the current number of GPEs
that are being managed by the ACPICA core (both FADT-based GPEs
and the GPEs contained in GPE block devices.)
Modify drivers/acpi/system.c to use these 2 new interfaces
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI_FUNCTION_TRACE is an internal acpica function.
remove ACPI_FUNCTION_TRACE
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI_FUNCTION_TRACE and return_VALUE are internal acpica functions.
remove ACPI_FUNCTION_TRACE
replace return_VALUE with return
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_namespace_node is internal struct, it should not be used outside of ACPICA
call acpi_get_name to get node ascii name
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
return_ACPI_STATUS is an internal acpica function, replace it with return.
acpi_gbl_permanent_mmap moved from acglobal.h to acpixf.h for external use
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
always update props.brightness no matter the backlight is changed
via procfs, hotkeys or sysfs.
Sighed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Len Brown <len.brown@intel.com>
use ACPI_ALLOCATE_BUFFER to remove the allocations
within acpi_pci_bind(), acpi_pci_unbind() and acpi_pci_bind_root().
While there, delete some unnecessary param inits from those routines.
Delete concept of ACPI_PATHNAME_MAX, since this was the last use.
Signed-off-by: Len Brown <len.brown@intel.com>
This patch makes function declarations consistent throughout
the file and removes some unnecessary initializations.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_pci_allocate_irq() and acpi_pci_free_irq() are trivial and
only used once, so just open-code them.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We don't need a struct containing a count and a list_head; a simple
list_head is sufficient. The list iterators handle empty lists
fine.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This folds acpi_pci_irq_derive() into acpi_pci_irq_lookup() so it
can be easily used by both acpi_pci_irq_enable() and acpi_pci_irq_disable().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
No functional change; this just uses the typical pattern of
PCI INTx swizzling done on other architectures.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This doesn't change anything functionally; it just changes tests
so we test for success instead of failure. This makes the code
read more easily and allows us to remove the "!entry" in the while
loop condition.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We currently pass a callback function (either acpi_pci_allocate_irq() or
acpi_pci_free_irq()) to acpi_pci_irq_lookup() and acpi_pci_irq_derive().
I think it's simpler to remove the callback and just have the enable/
disable functions make the calls directly.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Print one message (either "found" or "not found") for every _PRT
search. And add pin information to the INTx swizzling debug.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
There's no reason to pass around segment, bus, and device independently
when we can just pass the pci_dev pointer, which carries all those
already.
The pci_dev contains an interrupt pin, too, but we still have to pass both
the pci_dev and the pin because when we use a bridge to derive an IRQ, we
need the pin from the downstream device, not the bridge.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Use the PCI INTx pin encoding (1=INTA, 2=INTB, etc) for _PRT quirks.
Then we can simply compare "entry->pin == quirk->pin".
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch changes pci_irq.c to always use PCI INTx pin encodings
instead of a mix of PCI and _PRT encodings.
The PCI INTx pin numbers from the PCI_INTERRUPT_PIN config register
are 0=device doesn't use interrupts, 1=INTA, ..., 4=INTD. But the
_PRT table uses 0=INTA, ..., 3=INTD.
This patch converts the _PRT encoding to the PCI encoding immediately
when we add a _PRT entry to the global list. All the rest of the
code can then use the PCI encoding consistently.
The point of this is to make the interrupt swizzling look the same
as on other architectures, so someday we can unify them.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This adds a helper function to convert INTx pin numbers from the _PRT
(0, 1, 2, 3) to the pin name ('A', 'B', 'C', 'D').
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The struct acpi_prt_entry is used only in pci_irq.c, so there's no
need for the declaration to be public. This patch moves it into
pci_irq.c.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The interrupt numbers from _PRT entries are GSIs, not Linux IRQs.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
_PRT entries don't contain any useful PCI function information (the
function part of the PCI address is supposed to be 0xffff), and we
don't ever look at it, so this patch just removes the reference to
it.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Previously, acpi_pci_irq_add_prt() did all its own buffer management.
But now that we have ACPI_ALLOCATE_BUFFER, we no longer need to do
that management. And we don't have to call acpi_get_irq_routing_table()
twice (once to learn the size of the buffer needed, and again to
actually get the table).
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Better to oops and learn about a bug than to silently cover it up.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Use the conventional format for PCI addresses (%04x:%02x:%02x.%d).
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
According to the ACPI specification the SCI_EN flag is controlled by
the hardware, which sets this flag to inform the kernel that ACPI is
enabled. For this reason, we shouldn't try to modify SCI_EN
directly. Also, we don't need to do it in irqrouter_resume(), since
lower-level resume code takes care of enabling ACPI in case it hasn't
been enabled by the BIOS before passing control to the kernel (which
by the way is against the ACPI specification).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
For Windows compatibility, return an implicit integer of value
zero for methods that have no executable code. A default implicit
value of zero is provided for methods. Lin Ming.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Merge the code that validates control method argument counts into
the predefined validation module. Eliminates possible multiple
warnings for incorrect counts.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
For predefined methods (such as _BIF), add automatic conversion for
objects that are required to be a String, but a Buffer was found
instead. This can happen when reading string battery data from
an operation region, because it used to be difficult to convert
the data from buffer to string from within the ASL. Linux BZ 11822.
http://bugzilla.kernel.org/show_bug.cgi?id=11822
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
In a fully qualified namepath, allow multiple backslash prefixes.
This can happen because of the use of a double-backslash in strings
(since backslash is the escape character) causing confusion.
ACPICA BZ 739 Lin Ming.
http://www.acpica.org/bugzilla/show_bug.cgi?id=739
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes a problem where the use of an alias within a namepath
would result in a not found error or cause the compiler to fault.
Also now allows forward references from the Alias operator itself.
ACPICA BZ 738.
http://www.acpica.org/bugzilla/show_bug.cgi?id=738
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This define is no longer used.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The current implemenation of _OSI within ACPICA only allows other
control methods to execute _OSI. This change allows the host
OS to execute _OSI via the AcpiEvaluateObject interface. _OSI
is a special method -- it does not exist in the AML code, it is
implemented within ACPICA.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Reformat comments to use fewer lines.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Use a global pointer instead of using AcpiGetTableByIndex for
each FACS access. This simplifies the code for the Global Lock
and the Firmware Waking Vector(s).
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Checks if there are two valid but different addresses for the
FACS and DSDT within the FADT (mismatch between the 32-bit and
64-bit fields.)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This fixes the name of this address space, changing it from the
incorrect CMOS to the correct SystemCMOS.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Split the "data register I/O" with more informative read and
write messages.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add a loop counter to force exit from AML While loops if the
count becomes too large. This can occur in poorly written AML
when the hardware does not respond within a while loop and the
loop does not implement a timeout. The maximum loop count is
configurable. A new exception code is returned when a loop is
broken, AE_AML_INFINITE_LOOP. Bob Moore, Alexey Starikovskiy.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Previously, a control state object was allocated and freed for
each execution of the loop. The optimization is to simply reuse
the control state for each iteration. This speeds up the raw loop
execution time by about 5%.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes a possible memory leak if an allocation failure happens in
the parse loop. Must terminate an executing control method.
Lin Ming, Bob Moore. ACPICA BZ 489.
http://www.acpica.org/bugzilla/show_bug.cgi?id=489
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Split AcpiSetFirmwareWakingVector into two: one for the 32-bit
vector, another for the 64-bit vector. This is required because the
host OS must setup the wake much differently for each vector (real
vs. protected mode, etc.) and the interface should not be deciding
which vector to use. Also eliminate the GetFirmwareWakingVector
interface, as it served no purpose (only the firmware reads the
vector, OS only writes the vector.) ACPICA BZ 731.
http://www.acpica.org/bugzilla/show_bug.cgi?id=731
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
New compiler is pickier than older versions.
Joerg Sonnenberger. From ACPICA BZ 732.
http://www.acpica.org/bugzilla/show_bug.cgi?id=732
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
update of battery info fields is required.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Andy Neitzke <neitzke@ias.edu>
Signed-off-by: Alexey Starikovskiy <astarikovskiy <at> suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
These are platform specific drivers that happen to use ACPI,
while drivers/acpi/ is for code that implements ACPI itself.
Signed-off-by: Len Brown <len.brown@intel.com>
On some machines it may be necessary to disable the saving/restoring
of the ACPI NVS memory region during hibernation/resume. For this
purpose, introduce new ACPI kernel command line option
acpi_sleep=s4_nonvs.
Based on a patch by Zhang Rui.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@tuxonice.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
According to the ACPI Specification 3.0b, Section 15.3.2,
"OSPM will call the _PTS control method some time before entering a
sleeping state, to allow the platform's AML code to update this
memory image before entering the sleeping state. After the system
awakes from an S4 state, OSPM will restore this memory area and call
the _WAK control method to enable the BIOS to reclaim its memory
image." For this reason, implement a mechanism allowing us to save
the NVS memory during hibernation and to restore it during the
subsequent resume.
Based on a patch by Zhang Rui.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@tuxonice.net>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_early_init() was changed to over-write the cmdline param,
making it really inconvenient to set debug flags at boot-time.
Also,
This sets the default level to "info", which is what all the ACPI
drivers use. So to enable messages from drivers, you only have to
supply the "layer" (a.k.a. "component"). For non-"info" ACPI core
and ACPI interpreter messages, you have to supply both level and
layer masks, as before.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Impact: reward non-stop TSCs with good TSC-based clocksources, etc.
Add support for CPUID_0x80000007_Bit8 on Intel CPUs as well. This bit means
that the TSC is invariant with C/P/T states and always runs at constant
frequency.
With Intel CPUs, we have 3 classes
* CPUs where TSC runs at constant rate and does not stop n C-states
* CPUs where TSC runs at constant rate, but will stop in deep C-states
* CPUs where TSC rate will vary based on P/T-states and TSC will stop in deep
C-states.
To cover these 3, one feature bit (CONSTANT_TSC) is not enough. So, add a
second bit (NONSTOP_TSC). CONSTANT_TSC indicates that the TSC runs at
constant frequency irrespective of P/T-states, and NONSTOP_TSC indicates
that TSC does not stop in deep C-states.
CPUID_0x8000000_Bit8 indicates both these feature bit can be set.
We still have CONSTANT_TSC _set_ and NONSTOP_TSC _not_set_ on some older Intel
CPUs, based on model checks. We can use TSC on such CPUs for time, as long as
those CPUs do not support/enter deep C-states.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Section B.6.2 of ACPI 3.0b specification that defines _BCL method
doesn't require the brightness levels returned to be sorted.
At least ThinkPad SL300 (and probably all IdeaPads) returns the
array reversed (i.e. bightest levels have lowest indexes), which
causes the brightness management behave in completely reversed
manner on these machines (brightness increases when the laptop is
idle, while the display dims when used).
Sorting the array by brightness level values after reading the list
fixes the issue.
http://bugzilla.kernel.org/show_bug.cgi?id=12037
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix month wrap issue with readback from /proc/acpi/alarm
This bug has been around *forever*.
$ echo '2008-12-01 10:36:20' > /proc/acpi/alarm
$ cat /proc/acpi/alarm
2008-11-01 10:36:20
Note how the readback above shows the month incorrectly
when the alarm is set in the *next* calendar month.
But with this patch applied, it shows the correct month (12).
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This reverts commit 558073dd56, along with
the failed try to fix the regression it caused ("ACPI: Fix ACPI battery
regression introduced by commit 558073"), which just made things worse.
Commit aaad077638 (that failed "Fix ACPI
battery regression") got the voltage conversion confused, and fixed the
problem with Rafael's battery monitor apparently just by mistake.
So revert them both, getting us back to the 2.6.27 state in this, and
let's revisit it when people understand what's going on.
Noted-by: Paul Martin <pm@debian.org>
Requested-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <len.brown@intel.com>
Cc: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 558073dd56 ("ACPI: battery: Convert
discharge energy rate to current properly") caused the battery subsystem
to report wrong values of the remaining time on battery power and the
time until fully charged on Toshiba Portege R500 (and presumably on
other boxes too).
Fix the issue by correcting the conversion from mW to mA.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the warning introduced in commit c5279dee26,
and give the dummy variable a more verbose name.
drivers/acpi/ec.c: In function 'acpi_ec_ecdt_probe':
drivers/acpi/ec.c:1015: warning: ISO C90 forbids mixed declarations and code
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
the toshiba ACPI driver will, in a failure case, free the rfkill state
before stopping the polling timer that would use this state. More interesting,
in the same failure case handling, it calls the exit function, which also
frees the rfkill state, but after stopping the polling.
If the race happens, a NULL pointer is passed to rfkill_force_state()
which then causes a nice dereference.
Fix the race by just not doing the too-early freeing of the rfkill state.
This appears to be the cause of a hot issue on kerneloops.org; while I
have no solid evidence of that this patch will fix the issue, the race
appears rather real.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Linux will continue to ignore OSI(Linux),
except for a white-list containing a few systems.
So delete the black-list,
and stop soliciting user-feedback on the console.
Signed-off-by: Len Brown <len.brown@intel.com>
Some Apple boxes evidently require us to set SCI_EN on resume
directly, because if we don't do that, they hung somewhere in the
resume code path. Moreover, on these boxes it is not sufficient to
use acpi_enable() to turn ACPI on during resume. All of this is
against the ACPI specification which states that (1) the BIOS is
supposed to return from the S3 sleep state with ACPI enabled
(SCI_EN set) and (2) the SCI_EN bit is owned by the hardware and we
are not supposed to change it.
For this reason, blacklist the affected systems so that the SCI_EN
bit is set during resume on them.
[NOTE: Unconditional setting SCI_EN for all system on resume doesn't
work, because it makes some other systems crash (that's to be
expected). Also, it is not entirely clear right now if all of the
Apple boxes require this workaround.]
This patch fixes the recent regression tracked as
http://bugzilla.kernel.org/show_bug.cgi?id=12038
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Tino Keitel <tino.keitel@gmx.de>
Tested-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Now I know why I had strange "scheduling in atomic" problems:
acpi_evaluate_integer() does malloc(..., irqs_disabled() ? GFP_ATOMIC
: GFP_KERNEL)... which is (of course) broken.
There's no way to reliably tell if we need GFP_ATOMIC or not from
code, this one for example fails to detect spinlocks held.
Fortunately, allocation seems small enough to be done on stack.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Acked-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI battery interface reports its state either in mW or in mA, and
discharge rate in your case is reported in mW. power_supply interface
does not have such a parameter, so current_now parameter is used
for all cases. But in case of mW, reported discharge should
be converted into mA.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Ferenc Wagner <wferi@niif.hu>
Signed-off-by: Len Brown <len.brown@intel.com>
One more ASUS comes with empty ECDT, add a guard for it...
http://bugzilla.kernel.org/show_bug.cgi?id=11880
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Commit 0794469da3: ("ACPI: struct device -
replace bus_id with dev_name(), dev_set_name()") introduced a bug by
testing 'dev_name(ldev)' instead of 'ldev->bus' for NULL when printing
out the bus information.
So if ldev->bus was NULL, we'd oops.
Reported-and-tested-by: Bruno Prmont <bonbons@linux-vserver.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Len Brown <len.brown@intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This removes the acpi_irq_balance_set() interface from the PCI
interrupt link driver.
x86 used acpi_irq_balance_set() to tell the PCI interrupt link
driver to configure links to minimize IRQ sharing. But the link
driver can easily figure out whether to turn on IRQ balancing
based on the IRQ model (PIC/IOAPIC/etc), so we can get rid of
that external interface.
It's better for the driver to figure this out at init-time. If
we set it externally via the x86 code, the interface reduces
modularity, and we depend on the fact that acpi_process_madt()
happens before we process the kernel command line.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Disabling gpe might interfere with gpe detection/handling,
thus producing "interrupt not handled" errors.
Ironically, disabling of GPE from interrupt context is already
under spinlock, so only userspace needs to start using it.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Restart current transaction if we recieved unexpected GPEs instead
of needed ones.
http://bugzilla.kernel.org/show_bug.cgi?id=11896
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
There is a possibility that EC might break if next command is
issued within 1 us after write or burst-disable command.
Suggestd-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Make sure we can tell if the GPE storm workaround gets activated,
and avoid flooding the logs afterwards.
http://bugzilla.kernel.org/show_bug.cgi?id=11841
"plenty of line "ACPI: EC: non-query interrupt received,
switching to interrupt mode" in dmesg"
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
If an ACPI graphics device supports backlight brightness functions (cmp. with
latest ACPI spec Appendix B), let the ACPI video driver control backlight and
switch backlight control off in vendor specific ACPI drivers (asus_acpi,
thinkpad_acpi, eeepc, fujitsu_laptop, msi_laptop, sony_laptop, acer-wmi).
Currently it is possible to load above drivers and let both poke on the
brightness HW registers, the video and vendor specific ACPI drivers -> bad.
This patch provides the basic support to check for BIOS capabilities before
driver loading time. Driver specific modifications are in separate follow up
patches.
"acpi_backlight=vendor"
Prever vendor driver over ACPI driver for backlight.
"acpi_backlight=video" (default)
Prever ACPI driver over vendor driver for backlight.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This is a reimplemention of commit
0119509c4f
from Matthew Garrett <mjg59@srcf.ucam.org>
This patch got removed because of a regression: ThinkPads with a
Intel graphics card and an Integrated Graphics Device BIOS implementation
stopped working.
In fact, they only worked because the ACPI device of the discrete, the
wrong one, got used (via int10). So ACPI functions were poking on the wrong
hardware used which is a sever bug.
The next patch provides support for above ThinkPads to be able to
switch brightness via the legacy thinkpad_acpi driver and automatically
detect when to use it.
Original commit message from Matthew Garrett:
Vendors often ship machines with a choice of integrated or discrete
graphics, and use the same DSDT for both. As a result, the ACPI video
module will locate devices that may not exist on this specific platform.
Attempt to determine whether the device exists or not, and abort the
device creation if it doesn't.
http://bugzilla.kernel.org/show_bug.cgi?id=9614
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Len's tree branch release-2.6.27, found an unwanted return statement at
evgpe.c.
(git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
release-2.6.27)
Signed-of-by Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Reformat acpi.debug_layer and acpi.debug_level documentation so it's
more readable, add some clues about how to figure out the mask bits that
enable a specific ACPI_DEBUG_PRINT statement, and include some useful
examples.
Move the list of masks to Documentation/acpi/debug.txt (these are
copies of the authoritative values in acoutput.h and acpi_drivers.h).
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When CONFIG_ACPI_DEBUG=y, the default acpi_dbg_layer and acpi_dbg_level
values built into the ACPI CA have some debug output enabled. We'd
rather be quiet unless the user actually specified the acpi.debug_level
argument.
This enables distros to ship with CONFIG_ACPI_DEBUG=y without
inundating users with debug output.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
/sys/module/acpi/parameters/debug_layers used to contain only the
debug layers defined by the ACPI CA. This patch adds the additional
layer definitions for ACPI drivers.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Move all the component definitions for drivers to a single shared place,
include/acpi/acpi_drivers.h.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
breakage introduced by following patch
commit 27663c5855
Author: Matthew Wilcox <willy@linux.intel.com>
Date: Fri Oct 10 02:22:59 2008 -0400
acpi_evaluate_integer() does not clear passed variable if
there is an error at evaluation.
So if we ignore error, we must supply initialized variable.
http://bugzilla.kernel.org/show_bug.cgi?id=11917
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
Since commit bc45b1d39a acpi tables are
allowed to have an empty signature and /sys/firmware/acpi/tables uses the
signature as filename. Applications using naive recursion through /sys
loop forever. A possible solution would be: (replacing the zero length
filename with the string "NULL")
http://bugzilla.kernel.org/show_bug.cgi?id=11539
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Impact: cleanup
Use MACRO for rev 3 fadt id instead of 3 directly.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch is part of a larger patch series which will remove
the "char bus_id[20]" name string from struct device. The device
name is managed in the kobject anyway, and without any size
limitation, and just needlessly copied into "struct device".
To set and read the device name dev_name(dev) and dev_set_name(dev)
must be used. If your code uses static kobjects, which it shouldn't
do, "const char *init_name" can be used to statically provide the
name the registered device should have. At registration time, the
init_name field is cleared, to enforce the use of dev_name(dev) to
access the device name at a later time.
We need to get rid of all occurrences of bus_id in the entire tree
to be able to enable the new interface. Please apply this patch,
and possibly convert any remaining remaining occurrences of bus_id.
We want to submit a patch to -next, which will remove bus_id from
"struct device", to find the remaining pieces to convert, and finally
switch over to the new api, which will remove the 20 bytes array
and does no longer have a size limitation.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-Off-By: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Associating a Local SAPIC with a processor object is dependent upon the
processor object's definition type. CPUs declared as "Processor" should
use the Local SAPIC's 'processor_id', and CPUs declared as "Device"
should use the 'uid'. Note that for "Processor" declarations, even if a
'_UID' child object exists, it has no bearing with respect to mapping
Local SAPICs (see section 5.2.11.13 - Local SAPIC Structure; "Advanced
Configuration and Power Interface Specification", Revision 3.0b).
This patch changes the lsapic mapping logic to rely on the distinction of
how the processor object was declared - the mapping can't just try both
types of matches regardless of declaration type and rely on one failing
as is currently being done.
Signed-off-by: Myron Stowe <myron.stowe@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Declaring processors in ACPI namespace can be done using either a
"Processor" definition or a "Device" definition (see section 8.4 -
Declaring Processors; "Advanced Configuration and Power Interface
Specification", Revision 3.0b). Currently the two processor
declaration types are conflated.
This patch disambiguates the processor declaration's definition type
enabling subsequent code to behave uniquely based explicitly on the
declaration's type.
Signed-off-by: Myron Stowe <myron.stowe@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove CONFIG_ACPI_EC. It was always set the same as CONFIG_ACPI,
and it had no menu label, so there was no way to set it to anything
other than "y".
Per section 6.5.4 of the ACPI 3.0b specification,
OSPM must make Embedded Controller operation regions, accessed
via the Embedded Controllers described in ECDT, available before
executing any control method.
The ECDT table is optional, but if it is present, the above text
means that the EC it describes is a required part of the ACPI
subsystem, so CONFIG_ACPI_EC=n wouldn't make sense.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove CONFIG_ACPI_POWER. It was always set the same as CONFIG_ACPI,
and it had no menu label, so there was no way to set it to anything
other than "y".
The interfaces under CONFIG_ACPI_POWER (acpi_device_sleep_wake(),
acpi_power_transition(), etc) are called unconditionally from the
ACPI core, so we already depend on it always being present.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_cm_sbs_init() doesn't do anything, so we can just remove it.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
I don't think there's any point in cluttering the code with these.
Better to improve the documentation so *anybody* can figure out
what layer & level to use.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Introduce a new flag showing whether the event has an event handler/method.
For all the GPEs and Fixed Events,
1. ACPI_EVENT_FLAG_HANDLE is cleared, it's an "invalid" ACPI event.
2. Both ACPI_EVENT_FLAG_HANDLE and ACPI_EVENT_FLAG_DISABLE are set,
it's "disabled".
3. Both ACPI_EVENT_FLAG_HANDLE and ACPI_EVENT_FLAG_ENABLE are set,
it's "enabled".
4. Both ACPI_EVENT_FLAG_HANDLE and ACPI_EVENT_FLAG_WAKE_ENABLE are set,
it's "wake_enabled".
Among other things, this prevents incorrect reporting of ACPI events
as being "invalid" when it's really just (temporarily) "disabled".
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Len Brown <len.brown@intel.com>
On some laptops the Fan device is turned on/off by controlling the
corresponding power resource. For example: If the power resource
defined in _PR0 object is turned off, it indicates that the FAN device
is in off state(the ACPI state is in D3 state).
Maybe the device is already in D3 state and expected to be transited to
D3 state. As there is no _PR3 object, the power transition can't be
finished and it will be switched to the Unknown state.
Maybe it is more reasonable that the strick check in power transistion
is deleted.
http://bugzilla.kernel.org/show_bug.cgi?id=9485
Signed-off-by: yakui.zhao@intel.com
Signed-off-by: Len Brown <len.brown@intel.com>
Currently not always an EV_SYN event is reported to userland
after the EV_SW SW_LID event has been sent. This is easy to verify
by using “input-events” from input-utils and just closing and opening
the lid.
Signed-off-by: Guillem Jover <guillem.jover@nokia.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When trying to build 2.6.28-rc1 on ia64, make aborts with:
CC drivers/acpi/processor_perflib.o
drivers/acpi/processor_perflib.c:41:28: error: asm/cpufeature.h: No such file or directory
drivers/acpi/processor_perflib.c: In function ‘acpi_processor_get_performance_info’:
drivers/acpi/processor_perflib.c:364: error: implicit declaration of function ‘boot_cpu_has’
drivers/acpi/processor_perflib.c:364: error: ‘X86_FEATURE_EST’ undeclared (first use in this function)
drivers/acpi/processor_perflib.c:364: error: (Each undeclared identifier is reported only once
drivers/acpi/processor_perflib.c:364: error: for each function it appears in.)
make[2]: *** [drivers/acpi/processor_perflib.o] Error 1
make[1]: *** [drivers/acpi] Error 2
make: *** [drivers] Error 2
this patch fix it.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Acked-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (123 commits)
dock: make dock driver not a module
ACPI: fix ia64 build warning
ACPI: hack around sysfs warning with link order
ACPI suspend: fix build warning when CONFIG_ACPI_SLEEP=n
intel_menlo: fix build warning
panasonic-laptop: fix build
ACPICA: Update version to 20080926
ACPICA: Add support for zero-length buffer-to-string conversions
ACPICA: New: Validation for predefined ACPI methods/objects
ACPICA: Fix for implicit return compatibility
ACPICA: Fixed a couple memory leaks associated with "implicit return"
ACPICA: Optimize buffer allocation procedure
ACPICA: Fix possible memory leak, error exit path
ACPICA: Fix fault after mem allocation failure in AML parser
ACPICA: Remove unused ACPI register bit definition
ACPICA: Update version to 20080829
ACPICA: Fix possible memory leak in acpi_ns_get_external_pathname
ACPICA: Cleanup for internal Reference Object
ACPICA: Update comments - no functional changes
ACPICA: Update for Reference ACPI_OPERAND_OBJECT
...
To avoid dock driver is loaded after other drivers like libata, let's
make dock driver not a module.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
There exists the following warning message will appear after the
following commit is merged.
>commit f2e969acd6d5981e6b1272810002558650d0736e
>Author: Zhao Yakui <yakui.zhao@intel.com>
>Date: Mon Aug 11 14:57:50 2008 +0800
>ACPI: Add "acpi.power_nocheck=1" to disable power state check in
power transition:
>WARNING: at linux-2.6/fs/sysfs/dir.c:463 sysfs_add_one+0x33/0x39()
>sysfs: duplicate filename 'acpi' can not be created
>kobject_add_internal failed for acpi with -EEXIST, don't try to register
things with the same name in the same directory
In the above commit the "acpi.power_nocheck" module parameter is defined
in drivers/acpi/power.c file. As several module parameters using the same ACPI
prefix are defined in the different files(for example: power_nocheck is
defined in drivers/acpi/power.c,debug_layer/debug_level are defined in
drivers/acpi/debug.c) and there exists another module between them, the
warning message will be printed when using the current generic param code.
(In the function of param_sysfs_init).
In fact when ACPI is selected, the drivers/acpi/power will also be compiled
as built-in kernel.So this issue can be fixed by the following approach.
workaround it by adjusting the module link order in drivers/acpi/Makefile.
In such case the module parameter using the same prefix(ACPI) are put together
in the param data section.
Of course the better solution is to fix it in generic param code related
with sysfs.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Allow zero length strings during interpreter buffer-to-string
conversions. For example, during the ToDecimalString and
ToHexString operaters, as well as implicit conversions. Fiodor
Suietov. ACPICA BZ 585.
http://www.acpica.org/bugzilla/show_bug.cgi?id=585
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Validates predefined ACPI objects that appear in the namespace,
at the time they are evaluated. The argument count and the type of
the returned object are validated. The purpose of this validation
is to detect problems with the BIOS-exposed predefined ACPI objects
before the results are returned to the ACPI-related drivers.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Predicate can be used for an implicit return value.
This change improves the implicit return mechanism to be more
compatible with the MS interpreter.
http://www.acpica.org/bugzilla/show_bug.cgi?id=349
Below AML code from http://bugzilla.kernel.org/show_bug.cgi?id=10686
Store(0x07D6, OSYS)
Method (_CRT, 0, Serialized)
{
If (LLess (OSYS, 0x07D6))
{
If (LEqual (\_SB.TJ85, Zero))
{
Return (Add (0x0AAC, Multiply (TPC, 0x0A)))
}
Else
{
Return (Add (0x0AAC, Multiply (TP85, 0x0A)))
}
}
}
Previously _CRT returns 0x07D6, now it returns 0 (predicate value of LLess)
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixed a couple memory leaks associated with "implicit return" objects
when the AML Interpreter slack mode is enabled.
http://www.acpica.org/bugzilla/show_bug.cgi?id=349
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Eliminate duplicate code.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixed two possible memory leaks in the error exit paths of
acpi_ut_update_objerct_reference() and
acpi_ut_walk_package_tree()
These functions are similar in that they use a stack of state objects in
order to eliminate recursion. The stack must be fully deallocated
if an error occurs.
http://www.acpica.org/bugzilla/show_bug.cgi?id=383
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes a crash if a memory allocation fails during the Op completion
routine acpi_ps_complete_this_op().
http://www.acpica.org/bugzilla/show_bug.cgi?id=492
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Removed the ACPI_BITREG_WAKE_ENABLE definition and entry in the
global register table. This bit does not exist and is unused.
http://www.acpica.org/bugzilla/show_bug.cgi?id=442
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes a memory leak in the error exit path.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix some sloppiness in the Reference object. No longer use AML
opcodes to differentiate the types, introduce new reference
Class. Cleanup the debug output code.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Some formatting and spelling fixes.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
1) Add new field for use by DdbHandle (Value)
2) Use ACPI_CAST_INDIRECT_PTR to eliminate strict type warnings
3) Cleanup debug output
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Previously aborted with error if too few arguments were passed to
a control method via the external ACPICA interface. Now issue a
warning instead and continue. Handles the case where the method
inadvertently declares too many arguments, but does not actually
use the extra ones. Applies mainly to the predefined methods.
http://bugzilla.kernel.org/show_bug.cgi?id=11032
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Return AE_TYPE for objects that have no value and therefore
evaluation is undefined: Device, Event, Mutex, Region, Thermal,
and Scope.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Removed ACPI_DB_WARN and ACPI_DB_ERROR. These debug levels were
made obsolete by the ACPI_WARNING and ACPI_ERROR/ACPI_EXCEPTION
interfaces. Also added ACPI_DB_EVENTS to correspond with the
existing ACPI_LV_EVENTS.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI_DB_ERROR and ACPI_DB_WARN were removed from ACPICA core.
So replace ACPI_DEBUG_PRINT((ACPI_DB_ERROR, ...) with printk(KERN_ERR PREFIX ...)
and ACPI_DEBUG_PRINT((ACPI_DB_WARN, ...) with printk(KERN_WARNING PREFIX ...)
We do not use ACPI_ERROR/ACPI_WARNING since they're not exported, see
-------------------------------------------------------------
commit 6468463abd
Author: Len Brown <len.brown@intel.com>
Date: Mon Jun 26 23:41:38 2006 -0400
ACPI: un-export ACPI_ERROR() -- use printk(KERN_ERR...)
Signed-off-by: Len Brown <len.brown@intel.com>
-------------------------------------------------------------
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Better error messages during object conversion from internal
to the external ACPI_OBJECT. Used for external calls to
acpi_evaluate_object.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Created for improved error messages.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Also update the debugger so that the correct number of arguments is
passed to the method. Prevents a warning message from the debugger.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes warning from exconfig.c on 64-bit build.
AK: This actually was fixed earlier in Linux, this just syncs with
AK: the version of the fix that went into the ACPCA codebase
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Examines the return object from a call to acpi_evaluate_object.
Any Index or RefOf references are automatically dereferenced in
an attempt to return something useful (these reference types
cannot be converted into an external ACPI_OBJECT.)
Lin Ming, Bob Moore.
http://bugzilla.kernel.org/show_bug.cgi?id=11105
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Return status from acpi_ut_init_globals. This is used by both
the kernel subsystem and the utilities such as iASL compiler.
The function could possibly fail when the caches are initialized.
Yang Yi.
Signed-off-by: Yi Yang <yi.y.yang@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Split the ACPI table compare. First check that the lengths match
exactly. Then compare the data.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Without this change, a table cannot be loaded again once it has
been loaded/unloaded one time. The current mechanism does not
unregister a table upon an unload. During a load, if the same
table is found, this no longer returns an exception.
http://www.acpica.org/bugzilla/show_bug.cgi?id=722
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Return AE_BAD_PARAMETER if input handle is invalid.
http://www.acpica.org/bugzilla/show_bug.cgi?id=474
Signed-off-by: Fiodor Suietov <fiodor.f.suietov@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Previously, dynamically loaded tables were simply mapped, but on some machines
this memory is corrupted after suspend. Now copy the table to a local buffer.
For OpRegion case, added checksum verify. Use the table length from the table header,
not the region length. For Buffer case, use the table length also.
http://bugzilla.kernel.org/show_bug.cgi?id=10734
Signed-off-by: Dennis Noordsij <dennis.noordsij@helsinki.fi>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Slot detection drivers can co-exist with hotplug drivers. The names
of the detected/claimed slots may be different depending on module
load order.
For legacy reasons, we need to allow hotplug drivers to override
the slot name if a detection driver is loaded first (and they find
the same slots).
Creating and overriding slot names should be an atomic operation,
otherwise you get a locking nightmare as various drivers race to
call pci_create_slot().
pci_create_slot() is already serialized by grabbing the pci_bus_sem.
We update the API and add a 'hotplug' param, which is:
set if the caller is a hotplug driver
NULL if the caller is a detection driver
pci_create_slot() does not actually use the 'hotplug' parameter in this
patch. A later patch will add the logic that uses it.
Cc: kristen.c.accardi@intel.com
Cc: matthew@wil.cx
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Code in `pci_link.c' is calling the internal routine `acpi_ut_evaluate_object'
which is dangerous given that it is passing a NULL pointer when it should
be passing a pointer to a real object. The patch corrects the issue by
having the code call the external routine `acpi_evaluate_object', which
correctly handles a NULL pointer.
Signed-off-by: Don Dugger <donald.d.dugger@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
According to ACPI spec when the status of some device is not present
but functional, the device is valid and the children of this device
should be enumerated. It means that the device should be added to
linux acpi device tree. But the device driver for this device should not
be loaded.
The detailed info can be found in the section 6.3.7 of ACPI 3.0b spec.
_STA may return bit 0 clear (not present) with bit 3 set (device is
functional). This case is used to indicate a valid device for which no
device driver should be loaded (for example, a bridge device.).
Children of this device may be present and valid. OS should continue
enumeration below a device whose _STA returns this bit combination
http://bugzilla.kernel.org/show_bug.cgi?id=3358
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add the DMI check to disable power check in the course of device power
transistion.
http://bugzilla.kernel.org/show_bug.cgi?id=11000
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Maybe the incorrect power state is returned on the bogus bios, which
is different with the real power state. For example: the bios returns D0
state and the real power state is D3. OS expects to set the device to D0
state. In such case if OS uses the power state returned by the BIOS and
checks the device power state very strictly in power transition, the device
can't be transited to the correct power state.
So the boot option of "acpi.power_nocheck=1" is added to avoid checking
the device power in the course of device power transition.
http://bugzilla.kernel.org/show_bug.cgi?id=8049http://bugzilla.kernel.org/show_bug.cgi?id=11000
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Attach the ACPI device to the ACPI handle as early as possible so that OS
can get the corresponding ACPI device by the acpi handle in the course
of getting the power/wakeup/performance flags.
http://bugzilla.kernel.org/show_bug.cgi?id=8049http://bugzilla.kernel.org/show_bug.cgi?id=11000
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Get the device power state in the course of scanning device if the device
power flag is power_managable. i.e. The device has the _PSx/_PRx object.
At the same time before the drivers/acpi/power module is loaded, there is no
relation between acpi_power_resource and acpi device. So the first parameter
of acpi_power_get_state is changed to acpi_handle.
http://bugzilla.kernel.org/show_bug.cgi?id=8049http://bugzilla.kernel.org/show_bug.cgi?id=11000
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The AE_BAD_ADDRESS exception code is now unused in ACPICA.
For linux, it's only used at wmi.c and acer-wmi.c.
I checked both wmi.c and acer-wmi.c, the AE_BAD_ADDRESS exception code
has no special meaning. The parent functions just call AE_SUCCESS() or
AE_FAILURE() to check the return status.
So it's safe to replace AE_BAD_ADDRESS with AE_ERROR.
Signed-off-by Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Initially CONFIG_PM_SLEEP was defined as
CONFIG_SUSPEND || CONFIG_HIBERNATION and some ACPI code, most
importantly the code in drivers/acpi/main.c, was written with this
assumption. Currently, however, CONFIG_PM_SLEEP is also set when
CONFIG_XEN_SAVE_RESTORE is set.
This causes some compilation warnings to appear in
drivers/acpi/main.c if both CONFIG_SUSPEND and CONFIG_HIBERNATION
are unset and CONFIG_PM_SLEEP is set (this was impossible before).
To fix this problem, redefine CONFIG_ACPI_SLEEP do depend directly
on CONFIG_SUSPEND || CONFIG_HIBERNATION, as originally intended, and
use it instead of CONFIG_PM_SLEEP in drivers/acpi/main.c, wherever
appropriate.
Additionally, move the acpi_target_sleep_state definition from under
the #ifdef to prevent compilation from failing in some cases.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Tejun's commit 7b595756ec made sysfs
attribute->owner unnecessary. But the field was left in the structure to
ease the merge. It's been over a year since that change and it is now
time to start killing attribute->owner along with its users - one arch at
a time!
This patch is attempt #1 to get rid of attribute->owner only for
CONFIG_X86_64 or CONFIG_X86_32 . We will deal with other arches later on
as and when possible - avr32 will be the next since that is something I
can test. Compile (make allyesconfig / make allmodconfig / custom config)
and boot tested.
akpm: the idea is that we put the declaration of sttribute.owner inside
`#ifndef CONFIG_X86'. But that proved to be too ambitious for now because
new usages kept on turning up in subsystem trees.
[akpm: remove the ifdef for now]
Signed-off-by: Parag Warudkar <parag.lkml@gmail.com>
Cc: Greg KH <greg@kroah.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change ACPI to use the new bcd2bin/bin2bcd functions instead of the
obsolete BCD_TO_BIN/BIN_TO_BCD macros.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to ACPI 3.0, FADT.flags.RESET_REG_SUP indicates
whether the ACPI reboot mechanism is supported.
However, some boxes have this bit clear, have a valid
ACPI_RESET_REG & RESET_VALUE, and ACPI reboot is the only
mechanism that works for them after S3.
This suggests that other operating systems may not be checking
the RESET_REG_SUP bit, and are using other means to decide
whether to use the ACPI reboot mechanism or not.
Here we stop checking RESET_REG_SUP.
Instead, When acpi reboot is requested,
only the reset_register is checked. If the following
conditions are met, it indicates that the reset register is supported.
a. reset_register is not zero
b. the access width is eight
c. the bit_offset is zero
http://bugzilla.kernel.org/show_bug.cgi?id=7299http://bugzilla.kernel.org/show_bug.cgi?id=1148
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
http://bugzilla.kernel.org/show_bug.cgi?id=9129
lenb: Note that overriding a critical trip point
may simply fool the user into thinking that they
have control that they do not actually have.
For it is EC firmware that decides when the EC
sends Linux temperature change events, and the
EC may or may not decide to send Linux these events
anywhere in the neighborhood of the fake
override trip points. Beware.
note also that thermal.nocrt is already available
to disable crtical trip point actios,
and thermal.crt=-1 is already available to
disabled critical trip points entirely.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
On some broken BIOS the ACPI object in EC _REG method can't be found in
ACPI namespace, which causes that the status code of AE_NOT_FOUND is returned by
the EC _REG object. In such case the EC device can't be initialized correctly,
which causes that battery/AC adapter can't work normally. As the EC address
space handler is not removed and the memory pointed by its input argument is
already free, sometimes the kernel will also be panic when EC internal register
is still accessed. But the windows can work well on such broken BIOS.
Maybe it will be reasonable that OS ignores the AE_NOT_FOUND error
returned by the EC _REG object and continues to initialize EC device
on some broken BIOS.
For example: the ACPI object in EC _REG method can't be found and status error
code is AE_NOT_FOUND.
http://bugzilla.kernel.org/show_bug.cgi?id=8953http://bugzilla.kernel.org/show_bug.cgi?id=10237
lenb: we may find a more general solution to this in the future.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
asus_hotk_get_info should return -ENODEV if the model is not supported.
http://bugzilla.kernel.org/show_bug.cgi?id=10389
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
HP xw4600 Workstation is known to require the "old" (ie. compatible
with ACPI 1.0) suspend code ordering, so blacklist it for this
purpose.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: John Brown <john.brown3@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
On some machines, like for example MSI Wind U100, the BIOS doesn't
enable ACPI before returning control to the OS, which sometimes
causes resume to fail. This is against the ACPI specification,
which clearly states that "When the platform is waking from an S1, S2
or S3 state, OSPM assumes the hardware is already in the ACPI mode
and will not issue an ACPI_ENABLE", but it won't hurt to check the
SCI_EN bit and enable ACPI during resume from S3 if this bit is not
set.
Fortunately, we already have acpi_enable() for that, so use it in the
resume code path, before executing _BFS, in analogy with the
resume-from-hibernation code path.
NOTE: We aren't supposed to set SCI_EN directly, because it's owned
by the hardware.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
According to the ACPI specification 2.0c and later, the 64-bit waking vector
should be cleared and the 32-bit waking vector should be used, unless we want
the wake-up code to be called by the BIOS in Protected Mode. Moreover, some
systems (for example HP dv5-1004nr) are known to fail to resume if the 64-bit
waking vector is used. Therefore, modify the code to clear the 64-bit waking
vector, for FACS version 1 or greater, and set the 32-bit one before suspend.
http://bugzilla.kernel.org/show_bug.cgi?id=11368
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
The _TTS object is defined in the section 7.3 of acpi 3.0b spec.
The _TTS control method is executed by the OSPM at the beginning of
the sleep transition process for S1,S2, S3, S4, and orderly S5 shutdown.
OS will invoke _TTS before it has notified any native mode device drivers
of the sleep state transition. The target sleeping state value is passed to
the _TTS control method.
The _TTS control method is also executed by the OSPM at the end of
any sleep transition process when the system transitions to S0 from
S1, S2, S3, or S4. The _TTS object should be evaluated after it has
notified any native mode device drivers of the end of the sleep state
transition. The working state value (0) is passed to the _TTS control method.
So it is necessary to add the support for _TTS object. The _TTS object
will be evaluated if it exists.
At the same time a block notifier is added to the reboot notifier list so
that the _TTS object will also be evaluated when the system shutdown.
lenb: note that as of Sep 2008, I've not yet seen _TTS in any shipping BIOS.
So this patch is to future-proof Linux, rather than fix the installed base.
http://bugzilla.kernel.org/show_bug.cgi?id=11132
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
reflect the actual state entered in dev->last_state, when actaul state entered
is different from intended one.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The leading other brand OS appears to clear the WAK_STS flag on resume.
When rebooted, certain BIOSes assume that the system is actually
resuming if it's still set and so fail to reboot correctly. Make sure
that it's cleared at resume time.
Comment clarified as suggested by Bob Moore
http://bugzilla.kernel.org/show_bug.cgi?id=11634
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Tested-by: Romano Giannetti <romano.giannetti@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Move rtc_wake_setup() from drivers/acpi/glue.c into the RTC driver
in drivers/rtc/rtc-cmos.c.
This removes the ordering constraint between the module_init(acpi_rtc_init)
and the cmos_do_probe() code that depends on it.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit ed458df4d2 ("PnP: move
pnpacpi/pnpbios_init to after PCI init") moved the PnP RTC discovery
later, and now the ACPI RTC glue code doesn't find it any more, breaking
the RTC wakealarm sysfs interfaces, as reported by Rafael.
This really is fairly messy, and we have several annoying ordering
constraints here - the PnP code that sets up the RTC resources wants to
run after the PCI resources have to be registered, which in turn needs
to run after ACPI has at least enumerated the root PCI buses etc. Our
initcall ordering is not fine-grained enough to make this all painless.
So this moves the ACPI RTC glue ("acpi_rtc_init()") down to a regular
module call, which fixes the problem Rafael has. The reason this isn't
wonderful is that we really should do acpi_rtc_init before we do the
rtc_cmos init, and now those two are in the same module_init() section.
Which happens to work, but only because drivers/rtc is linked after
drivers/acpi. In other words, we still have a very subtle ordering
issue here. Grr.
Reported-and-tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
