diff --git a/drivers/net/e1000/e1000.h b/drivers/net/e1000/e1000.h index 3042d33e2d4..f411bbb44f8 100644 --- a/drivers/net/e1000/e1000.h +++ b/drivers/net/e1000/e1000.h @@ -68,7 +68,6 @@ #ifdef NETIF_F_TSO #include #endif -#include #include #include #include @@ -143,6 +142,7 @@ struct e1000_adapter; #define AUTO_ALL_MODES 0 #define E1000_EEPROM_82544_APM 0x0004 +#define E1000_EEPROM_ICH8_APME 0x0004 #define E1000_EEPROM_APME 0x0400 #ifndef E1000_MASTER_SLAVE @@ -254,7 +254,6 @@ struct e1000_adapter { spinlock_t tx_queue_lock; #endif atomic_t irq_sem; - struct work_struct watchdog_task; struct work_struct reset_task; uint8_t fc_autoneg; @@ -339,8 +338,14 @@ struct e1000_adapter { #ifdef NETIF_F_TSO boolean_t tso_force; #endif + boolean_t smart_power_down; /* phy smart power down */ + unsigned long flags; }; +enum e1000_state_t { + __E1000_DRIVER_TESTING, + __E1000_RESETTING, +}; /* e1000_main.c */ extern char e1000_driver_name[]; @@ -348,6 +353,7 @@ extern char e1000_driver_version[]; int e1000_up(struct e1000_adapter *adapter); void e1000_down(struct e1000_adapter *adapter); void e1000_reset(struct e1000_adapter *adapter); +void e1000_reinit_locked(struct e1000_adapter *adapter); int e1000_setup_all_tx_resources(struct e1000_adapter *adapter); void e1000_free_all_tx_resources(struct e1000_adapter *adapter); int e1000_setup_all_rx_resources(struct e1000_adapter *adapter); diff --git a/drivers/net/e1000/e1000_ethtool.c b/drivers/net/e1000/e1000_ethtool.c index d1966489176..88a82ba88f5 100644 --- a/drivers/net/e1000/e1000_ethtool.c +++ b/drivers/net/e1000/e1000_ethtool.c @@ -109,7 +109,8 @@ e1000_get_settings(struct net_device *netdev, struct ethtool_cmd *ecmd) SUPPORTED_1000baseT_Full| SUPPORTED_Autoneg | SUPPORTED_TP); - + if (hw->phy_type == e1000_phy_ife) + ecmd->supported &= ~SUPPORTED_1000baseT_Full; ecmd->advertising = ADVERTISED_TP; if (hw->autoneg == 1) { @@ -203,11 +204,9 @@ e1000_set_settings(struct net_device *netdev, struct ethtool_cmd *ecmd) /* reset the link */ - if (netif_running(adapter->netdev)) { - e1000_down(adapter); - e1000_reset(adapter); - e1000_up(adapter); - } else + if (netif_running(adapter->netdev)) + e1000_reinit_locked(adapter); + else e1000_reset(adapter); return 0; @@ -254,10 +253,9 @@ e1000_set_pauseparam(struct net_device *netdev, hw->original_fc = hw->fc; if (adapter->fc_autoneg == AUTONEG_ENABLE) { - if (netif_running(adapter->netdev)) { - e1000_down(adapter); - e1000_up(adapter); - } else + if (netif_running(adapter->netdev)) + e1000_reinit_locked(adapter); + else e1000_reset(adapter); } else return ((hw->media_type == e1000_media_type_fiber) ? @@ -279,10 +277,9 @@ e1000_set_rx_csum(struct net_device *netdev, uint32_t data) struct e1000_adapter *adapter = netdev_priv(netdev); adapter->rx_csum = data; - if (netif_running(netdev)) { - e1000_down(adapter); - e1000_up(adapter); - } else + if (netif_running(netdev)) + e1000_reinit_locked(adapter); + else e1000_reset(adapter); return 0; } @@ -577,6 +574,7 @@ e1000_get_drvinfo(struct net_device *netdev, case e1000_82572: case e1000_82573: case e1000_80003es2lan: + case e1000_ich8lan: sprintf(firmware_version, "%d.%d-%d", (eeprom_data & 0xF000) >> 12, (eeprom_data & 0x0FF0) >> 4, @@ -631,6 +629,9 @@ e1000_set_ringparam(struct net_device *netdev, tx_ring_size = sizeof(struct e1000_tx_ring) * adapter->num_tx_queues; rx_ring_size = sizeof(struct e1000_rx_ring) * adapter->num_rx_queues; + while (test_and_set_bit(__E1000_RESETTING, &adapter->flags)) + msleep(1); + if (netif_running(adapter->netdev)) e1000_down(adapter); @@ -691,9 +692,11 @@ e1000_set_ringparam(struct net_device *netdev, adapter->rx_ring = rx_new; adapter->tx_ring = tx_new; if ((err = e1000_up(adapter))) - return err; + goto err_setup; } + clear_bit(__E1000_RESETTING, &adapter->flags); + return 0; err_setup_tx: e1000_free_all_rx_resources(adapter); @@ -701,6 +704,8 @@ err_setup_rx: adapter->rx_ring = rx_old; adapter->tx_ring = tx_old; e1000_up(adapter); +err_setup: + clear_bit(__E1000_RESETTING, &adapter->flags); return err; } @@ -754,6 +759,7 @@ e1000_reg_test(struct e1000_adapter *adapter, uint64_t *data) toggle = 0x7FFFF3FF; break; case e1000_82573: + case e1000_ich8lan: toggle = 0x7FFFF033; break; default: @@ -773,11 +779,12 @@ e1000_reg_test(struct e1000_adapter *adapter, uint64_t *data) } /* restore previous status */ E1000_WRITE_REG(&adapter->hw, STATUS, before); - - REG_PATTERN_TEST(FCAL, 0xFFFFFFFF, 0xFFFFFFFF); - REG_PATTERN_TEST(FCAH, 0x0000FFFF, 0xFFFFFFFF); - REG_PATTERN_TEST(FCT, 0x0000FFFF, 0xFFFFFFFF); - REG_PATTERN_TEST(VET, 0x0000FFFF, 0xFFFFFFFF); + if (adapter->hw.mac_type != e1000_ich8lan) { + REG_PATTERN_TEST(FCAL, 0xFFFFFFFF, 0xFFFFFFFF); + REG_PATTERN_TEST(FCAH, 0x0000FFFF, 0xFFFFFFFF); + REG_PATTERN_TEST(FCT, 0x0000FFFF, 0xFFFFFFFF); + REG_PATTERN_TEST(VET, 0x0000FFFF, 0xFFFFFFFF); + } REG_PATTERN_TEST(RDTR, 0x0000FFFF, 0xFFFFFFFF); REG_PATTERN_TEST(RDBAH, 0xFFFFFFFF, 0xFFFFFFFF); REG_PATTERN_TEST(RDLEN, 0x000FFF80, 0x000FFFFF); @@ -790,20 +797,22 @@ e1000_reg_test(struct e1000_adapter *adapter, uint64_t *data) REG_PATTERN_TEST(TDLEN, 0x000FFF80, 0x000FFFFF); REG_SET_AND_CHECK(RCTL, 0xFFFFFFFF, 0x00000000); - REG_SET_AND_CHECK(RCTL, 0x06DFB3FE, 0x003FFFFB); + before = (adapter->hw.mac_type == e1000_ich8lan ? + 0x06C3B33E : 0x06DFB3FE); + REG_SET_AND_CHECK(RCTL, before, 0x003FFFFB); REG_SET_AND_CHECK(TCTL, 0xFFFFFFFF, 0x00000000); if (adapter->hw.mac_type >= e1000_82543) { - REG_SET_AND_CHECK(RCTL, 0x06DFB3FE, 0xFFFFFFFF); + REG_SET_AND_CHECK(RCTL, before, 0xFFFFFFFF); REG_PATTERN_TEST(RDBAL, 0xFFFFFFF0, 0xFFFFFFFF); - REG_PATTERN_TEST(TXCW, 0xC000FFFF, 0x0000FFFF); + if (adapter->hw.mac_type != e1000_ich8lan) + REG_PATTERN_TEST(TXCW, 0xC000FFFF, 0x0000FFFF); REG_PATTERN_TEST(TDBAL, 0xFFFFFFF0, 0xFFFFFFFF); REG_PATTERN_TEST(TIDV, 0x0000FFFF, 0x0000FFFF); - - for (i = 0; i < E1000_RAR_ENTRIES; i++) { - REG_PATTERN_TEST(RA + ((i << 1) << 2), 0xFFFFFFFF, - 0xFFFFFFFF); + value = (adapter->hw.mac_type == e1000_ich8lan ? + E1000_RAR_ENTRIES_ICH8LAN : E1000_RAR_ENTRIES); + for (i = 0; i < value; i++) { REG_PATTERN_TEST(RA + (((i << 1) + 1) << 2), 0x8003FFFF, 0xFFFFFFFF); } @@ -817,7 +826,9 @@ e1000_reg_test(struct e1000_adapter *adapter, uint64_t *data) } - for (i = 0; i < E1000_MC_TBL_SIZE; i++) + value = (adapter->hw.mac_type == e1000_ich8lan ? + E1000_MC_TBL_SIZE_ICH8LAN : E1000_MC_TBL_SIZE); + for (i = 0; i < value; i++) REG_PATTERN_TEST(MTA + (i << 2), 0xFFFFFFFF, 0xFFFFFFFF); *data = 0; @@ -889,6 +900,8 @@ e1000_intr_test(struct e1000_adapter *adapter, uint64_t *data) /* Test each interrupt */ for (; i < 10; i++) { + if (adapter->hw.mac_type == e1000_ich8lan && i == 8) + continue; /* Interrupt to test */ mask = 1 << i; @@ -1246,18 +1259,33 @@ e1000_integrated_phy_loopback(struct e1000_adapter *adapter) } else if (adapter->hw.phy_type == e1000_phy_gg82563) { e1000_write_phy_reg(&adapter->hw, GG82563_PHY_KMRN_MODE_CTRL, - 0x1CE); + 0x1CC); } - /* force 1000, set loopback */ - e1000_write_phy_reg(&adapter->hw, PHY_CTRL, 0x4140); - /* Now set up the MAC to the same speed/duplex as the PHY. */ ctrl_reg = E1000_READ_REG(&adapter->hw, CTRL); - ctrl_reg &= ~E1000_CTRL_SPD_SEL; /* Clear the speed sel bits */ - ctrl_reg |= (E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */ - E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */ - E1000_CTRL_SPD_1000 |/* Force Speed to 1000 */ - E1000_CTRL_FD); /* Force Duplex to FULL */ + + if (adapter->hw.phy_type == e1000_phy_ife) { + /* force 100, set loopback */ + e1000_write_phy_reg(&adapter->hw, PHY_CTRL, 0x6100); + + /* Now set up the MAC to the same speed/duplex as the PHY. */ + ctrl_reg &= ~E1000_CTRL_SPD_SEL; /* Clear the speed sel bits */ + ctrl_reg |= (E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */ + E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */ + E1000_CTRL_SPD_100 |/* Force Speed to 100 */ + E1000_CTRL_FD); /* Force Duplex to FULL */ + } else { + /* force 1000, set loopback */ + e1000_write_phy_reg(&adapter->hw, PHY_CTRL, 0x4140); + + /* Now set up the MAC to the same speed/duplex as the PHY. */ + ctrl_reg = E1000_READ_REG(&adapter->hw, CTRL); + ctrl_reg &= ~E1000_CTRL_SPD_SEL; /* Clear the speed sel bits */ + ctrl_reg |= (E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */ + E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */ + E1000_CTRL_SPD_1000 |/* Force Speed to 1000 */ + E1000_CTRL_FD); /* Force Duplex to FULL */ + } if (adapter->hw.media_type == e1000_media_type_copper && adapter->hw.phy_type == e1000_phy_m88) { @@ -1317,6 +1345,7 @@ e1000_set_phy_loopback(struct e1000_adapter *adapter) case e1000_82572: case e1000_82573: case e1000_80003es2lan: + case e1000_ich8lan: return e1000_integrated_phy_loopback(adapter); break; @@ -1568,6 +1597,7 @@ e1000_diag_test(struct net_device *netdev, struct e1000_adapter *adapter = netdev_priv(netdev); boolean_t if_running = netif_running(netdev); + set_bit(__E1000_DRIVER_TESTING, &adapter->flags); if (eth_test->flags == ETH_TEST_FL_OFFLINE) { /* Offline tests */ @@ -1582,7 +1612,8 @@ e1000_diag_test(struct net_device *netdev, eth_test->flags |= ETH_TEST_FL_FAILED; if (if_running) - e1000_down(adapter); + /* indicate we're in test mode */ + dev_close(netdev); else e1000_reset(adapter); @@ -1607,8 +1638,9 @@ e1000_diag_test(struct net_device *netdev, adapter->hw.autoneg = autoneg; e1000_reset(adapter); + clear_bit(__E1000_DRIVER_TESTING, &adapter->flags); if (if_running) - e1000_up(adapter); + dev_open(netdev); } else { /* Online tests */ if (e1000_link_test(adapter, &data[4])) @@ -1619,6 +1651,8 @@ e1000_diag_test(struct net_device *netdev, data[1] = 0; data[2] = 0; data[3] = 0; + + clear_bit(__E1000_DRIVER_TESTING, &adapter->flags); } msleep_interruptible(4 * 1000); } @@ -1778,21 +1812,18 @@ e1000_phys_id(struct net_device *netdev, uint32_t data) mod_timer(&adapter->blink_timer, jiffies); msleep_interruptible(data * 1000); del_timer_sync(&adapter->blink_timer); - } else if (adapter->hw.mac_type < e1000_82573) { - E1000_WRITE_REG(&adapter->hw, LEDCTL, - (E1000_LEDCTL_LED2_BLINK_RATE | - E1000_LEDCTL_LED0_BLINK | E1000_LEDCTL_LED2_BLINK | - (E1000_LEDCTL_MODE_LED_ON << E1000_LEDCTL_LED2_MODE_SHIFT) | - (E1000_LEDCTL_MODE_LINK_ACTIVITY << E1000_LEDCTL_LED0_MODE_SHIFT) | - (E1000_LEDCTL_MODE_LED_OFF << E1000_LEDCTL_LED1_MODE_SHIFT))); + } else if (adapter->hw.phy_type == e1000_phy_ife) { + if (!adapter->blink_timer.function) { + init_timer(&adapter->blink_timer); + adapter->blink_timer.function = e1000_led_blink_callback; + adapter->blink_timer.data = (unsigned long) adapter; + } + mod_timer(&adapter->blink_timer, jiffies); msleep_interruptible(data * 1000); + del_timer_sync(&adapter->blink_timer); + e1000_write_phy_reg(&(adapter->hw), IFE_PHY_SPECIAL_CONTROL_LED, 0); } else { - E1000_WRITE_REG(&adapter->hw, LEDCTL, - (E1000_LEDCTL_LED2_BLINK_RATE | - E1000_LEDCTL_LED1_BLINK | E1000_LEDCTL_LED2_BLINK | - (E1000_LEDCTL_MODE_LED_ON << E1000_LEDCTL_LED2_MODE_SHIFT) | - (E1000_LEDCTL_MODE_LINK_ACTIVITY << E1000_LEDCTL_LED1_MODE_SHIFT) | - (E1000_LEDCTL_MODE_LED_OFF << E1000_LEDCTL_LED0_MODE_SHIFT))); + e1000_blink_led_start(&adapter->hw); msleep_interruptible(data * 1000); } @@ -1807,10 +1838,8 @@ static int e1000_nway_reset(struct net_device *netdev) { struct e1000_adapter *adapter = netdev_priv(netdev); - if (netif_running(netdev)) { - e1000_down(adapter); - e1000_up(adapter); - } + if (netif_running(netdev)) + e1000_reinit_locked(adapter); return 0; } diff --git a/drivers/net/e1000/e1000_hw.c b/drivers/net/e1000/e1000_hw.c index 3959039b16e..583518ae49c 100644 --- a/drivers/net/e1000/e1000_hw.c +++ b/drivers/net/e1000/e1000_hw.c @@ -101,7 +101,8 @@ static void e1000_write_reg_io(struct e1000_hw *hw, uint32_t offset, #define E1000_WRITE_REG_IO(a, reg, val) \ e1000_write_reg_io((a), E1000_##reg, val) -static int32_t e1000_configure_kmrn_for_10_100(struct e1000_hw *hw); +static int32_t e1000_configure_kmrn_for_10_100(struct e1000_hw *hw, + uint16_t duplex); static int32_t e1000_configure_kmrn_for_1000(struct e1000_hw *hw); /* IGP cable length table */ @@ -156,6 +157,14 @@ e1000_set_phy_type(struct e1000_hw *hw) hw->phy_type = e1000_phy_igp; break; } + case IGP03E1000_E_PHY_ID: + hw->phy_type = e1000_phy_igp_3; + break; + case IFE_E_PHY_ID: + case IFE_PLUS_E_PHY_ID: + case IFE_C_E_PHY_ID: + hw->phy_type = e1000_phy_ife; + break; case GG82563_E_PHY_ID: if (hw->mac_type == e1000_80003es2lan) { hw->phy_type = e1000_phy_gg82563; @@ -332,6 +341,7 @@ e1000_set_mac_type(struct e1000_hw *hw) break; case E1000_DEV_ID_82541EI: case E1000_DEV_ID_82541EI_MOBILE: + case E1000_DEV_ID_82541ER_LOM: hw->mac_type = e1000_82541; break; case E1000_DEV_ID_82541ER: @@ -341,6 +351,7 @@ e1000_set_mac_type(struct e1000_hw *hw) hw->mac_type = e1000_82541_rev_2; break; case E1000_DEV_ID_82547EI: + case E1000_DEV_ID_82547EI_MOBILE: hw->mac_type = e1000_82547; break; case E1000_DEV_ID_82547GI: @@ -354,6 +365,7 @@ e1000_set_mac_type(struct e1000_hw *hw) case E1000_DEV_ID_82572EI_COPPER: case E1000_DEV_ID_82572EI_FIBER: case E1000_DEV_ID_82572EI_SERDES: + case E1000_DEV_ID_82572EI: hw->mac_type = e1000_82572; break; case E1000_DEV_ID_82573E: @@ -361,16 +373,29 @@ e1000_set_mac_type(struct e1000_hw *hw) case E1000_DEV_ID_82573L: hw->mac_type = e1000_82573; break; + case E1000_DEV_ID_80003ES2LAN_COPPER_SPT: + case E1000_DEV_ID_80003ES2LAN_SERDES_SPT: case E1000_DEV_ID_80003ES2LAN_COPPER_DPT: case E1000_DEV_ID_80003ES2LAN_SERDES_DPT: hw->mac_type = e1000_80003es2lan; break; + case E1000_DEV_ID_ICH8_IGP_M_AMT: + case E1000_DEV_ID_ICH8_IGP_AMT: + case E1000_DEV_ID_ICH8_IGP_C: + case E1000_DEV_ID_ICH8_IFE: + case E1000_DEV_ID_ICH8_IGP_M: + hw->mac_type = e1000_ich8lan; + break; default: /* Should never have loaded on this device */ return -E1000_ERR_MAC_TYPE; } switch(hw->mac_type) { + case e1000_ich8lan: + hw->swfwhw_semaphore_present = TRUE; + hw->asf_firmware_present = TRUE; + break; case e1000_80003es2lan: hw->swfw_sync_present = TRUE; /* fall through */ @@ -423,6 +448,7 @@ e1000_set_media_type(struct e1000_hw *hw) case e1000_82542_rev2_1: hw->media_type = e1000_media_type_fiber; break; + case e1000_ich8lan: case e1000_82573: /* The STATUS_TBIMODE bit is reserved or reused for the this * device. @@ -527,6 +553,14 @@ e1000_reset_hw(struct e1000_hw *hw) } while(timeout); } + /* Workaround for ICH8 bit corruption issue in FIFO memory */ + if (hw->mac_type == e1000_ich8lan) { + /* Set Tx and Rx buffer allocation to 8k apiece. */ + E1000_WRITE_REG(hw, PBA, E1000_PBA_8K); + /* Set Packet Buffer Size to 16k. */ + E1000_WRITE_REG(hw, PBS, E1000_PBS_16K); + } + /* Issue a global reset to the MAC. This will reset the chip's * transmit, receive, DMA, and link units. It will not effect * the current PCI configuration. The global reset bit is self- @@ -550,6 +584,20 @@ e1000_reset_hw(struct e1000_hw *hw) /* Reset is performed on a shadow of the control register */ E1000_WRITE_REG(hw, CTRL_DUP, (ctrl | E1000_CTRL_RST)); break; + case e1000_ich8lan: + if (!hw->phy_reset_disable && + e1000_check_phy_reset_block(hw) == E1000_SUCCESS) { + /* e1000_ich8lan PHY HW reset requires MAC CORE reset + * at the same time to make sure the interface between + * MAC and the external PHY is reset. + */ + ctrl |= E1000_CTRL_PHY_RST; + } + + e1000_get_software_flag(hw); + E1000_WRITE_REG(hw, CTRL, (ctrl | E1000_CTRL_RST)); + msec_delay(5); + break; default: E1000_WRITE_REG(hw, CTRL, (ctrl | E1000_CTRL_RST)); break; @@ -591,6 +639,7 @@ e1000_reset_hw(struct e1000_hw *hw) /* fall through */ case e1000_82571: case e1000_82572: + case e1000_ich8lan: case e1000_80003es2lan: ret_val = e1000_get_auto_rd_done(hw); if(ret_val) @@ -633,6 +682,12 @@ e1000_reset_hw(struct e1000_hw *hw) e1000_pci_set_mwi(hw); } + if (hw->mac_type == e1000_ich8lan) { + uint32_t kab = E1000_READ_REG(hw, KABGTXD); + kab |= E1000_KABGTXD_BGSQLBIAS; + E1000_WRITE_REG(hw, KABGTXD, kab); + } + return E1000_SUCCESS; } @@ -675,9 +730,12 @@ e1000_init_hw(struct e1000_hw *hw) /* Disabling VLAN filtering. */ DEBUGOUT("Initializing the IEEE VLAN\n"); - if (hw->mac_type < e1000_82545_rev_3) - E1000_WRITE_REG(hw, VET, 0); - e1000_clear_vfta(hw); + /* VET hardcoded to standard value and VFTA removed in ICH8 LAN */ + if (hw->mac_type != e1000_ich8lan) { + if (hw->mac_type < e1000_82545_rev_3) + E1000_WRITE_REG(hw, VET, 0); + e1000_clear_vfta(hw); + } /* For 82542 (rev 2.0), disable MWI and put the receiver into reset */ if(hw->mac_type == e1000_82542_rev2_0) { @@ -705,8 +763,14 @@ e1000_init_hw(struct e1000_hw *hw) /* Zero out the Multicast HASH table */ DEBUGOUT("Zeroing the MTA\n"); mta_size = E1000_MC_TBL_SIZE; - for(i = 0; i < mta_size; i++) + if (hw->mac_type == e1000_ich8lan) + mta_size = E1000_MC_TBL_SIZE_ICH8LAN; + for(i = 0; i < mta_size; i++) { E1000_WRITE_REG_ARRAY(hw, MTA, i, 0); + /* use write flush to prevent Memory Write Block (MWB) from + * occuring when accessing our register space */ + E1000_WRITE_FLUSH(hw); + } /* Set the PCI priority bit correctly in the CTRL register. This * determines if the adapter gives priority to receives, or if it @@ -744,6 +808,10 @@ e1000_init_hw(struct e1000_hw *hw) break; } + /* More time needed for PHY to initialize */ + if (hw->mac_type == e1000_ich8lan) + msec_delay(15); + /* Call a subroutine to configure the link and setup flow control. */ ret_val = e1000_setup_link(hw); @@ -757,6 +825,7 @@ e1000_init_hw(struct e1000_hw *hw) case e1000_82571: case e1000_82572: case e1000_82573: + case e1000_ich8lan: case e1000_80003es2lan: ctrl |= E1000_TXDCTL_COUNT_DESC; break; @@ -795,6 +864,7 @@ e1000_init_hw(struct e1000_hw *hw) /* Fall through */ case e1000_82571: case e1000_82572: + case e1000_ich8lan: ctrl = E1000_READ_REG(hw, TXDCTL1); ctrl = (ctrl & ~E1000_TXDCTL_WTHRESH) | E1000_TXDCTL_FULL_TX_DESC_WB; if(hw->mac_type >= e1000_82571) @@ -818,6 +888,11 @@ e1000_init_hw(struct e1000_hw *hw) */ e1000_clear_hw_cntrs(hw); + /* ICH8 No-snoop bits are opposite polarity. + * Set to snoop by default after reset. */ + if (hw->mac_type == e1000_ich8lan) + e1000_set_pci_ex_no_snoop(hw, PCI_EX_82566_SNOOP_ALL); + if (hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER || hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3) { ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); @@ -905,6 +980,7 @@ e1000_setup_link(struct e1000_hw *hw) */ if (hw->fc == e1000_fc_default) { switch (hw->mac_type) { + case e1000_ich8lan: case e1000_82573: hw->fc = e1000_fc_full; break; @@ -971,9 +1047,12 @@ e1000_setup_link(struct e1000_hw *hw) */ DEBUGOUT("Initializing the Flow Control address, type and timer regs\n"); - E1000_WRITE_REG(hw, FCAL, FLOW_CONTROL_ADDRESS_LOW); - E1000_WRITE_REG(hw, FCAH, FLOW_CONTROL_ADDRESS_HIGH); - E1000_WRITE_REG(hw, FCT, FLOW_CONTROL_TYPE); + /* FCAL/H and FCT are hardcoded to standard values in e1000_ich8lan. */ + if (hw->mac_type != e1000_ich8lan) { + E1000_WRITE_REG(hw, FCT, FLOW_CONTROL_TYPE); + E1000_WRITE_REG(hw, FCAH, FLOW_CONTROL_ADDRESS_HIGH); + E1000_WRITE_REG(hw, FCAL, FLOW_CONTROL_ADDRESS_LOW); + } E1000_WRITE_REG(hw, FCTTV, hw->fc_pause_time); @@ -1237,12 +1316,13 @@ e1000_copper_link_igp_setup(struct e1000_hw *hw) /* Wait 10ms for MAC to configure PHY from eeprom settings */ msec_delay(15); - + if (hw->mac_type != e1000_ich8lan) { /* Configure activity LED after PHY reset */ led_ctrl = E1000_READ_REG(hw, LEDCTL); led_ctrl &= IGP_ACTIVITY_LED_MASK; led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE); E1000_WRITE_REG(hw, LEDCTL, led_ctrl); + } /* disable lplu d3 during driver init */ ret_val = e1000_set_d3_lplu_state(hw, FALSE); @@ -1478,8 +1558,7 @@ e1000_copper_link_ggp_setup(struct e1000_hw *hw) if (ret_val) return ret_val; - /* Enable Pass False Carrier on the PHY */ - phy_data |= GG82563_KMCR_PASS_FALSE_CARRIER; + phy_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, phy_data); @@ -1561,28 +1640,40 @@ e1000_copper_link_mgp_setup(struct e1000_hw *hw) phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL; if(hw->disable_polarity_correction == 1) phy_data |= M88E1000_PSCR_POLARITY_REVERSAL; - ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); - if(ret_val) - return ret_val; - - /* Force TX_CLK in the Extended PHY Specific Control Register - * to 25MHz clock. - */ - ret_val = e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data); - if(ret_val) + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); + if (ret_val) return ret_val; - phy_data |= M88E1000_EPSCR_TX_CLK_25; - if (hw->phy_revision < M88E1011_I_REV_4) { - /* Configure Master and Slave downshift values */ - phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK | - M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK); - phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X | - M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X); - ret_val = e1000_write_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, phy_data); - if(ret_val) + /* Force TX_CLK in the Extended PHY Specific Control Register + * to 25MHz clock. + */ + ret_val = e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data); + if (ret_val) return ret_val; + + phy_data |= M88E1000_EPSCR_TX_CLK_25; + + if ((hw->phy_revision == E1000_REVISION_2) && + (hw->phy_id == M88E1111_I_PHY_ID)) { + /* Vidalia Phy, set the downshift counter to 5x */ + phy_data &= ~(M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK); + phy_data |= M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X; + ret_val = e1000_write_phy_reg(hw, + M88E1000_EXT_PHY_SPEC_CTRL, phy_data); + if (ret_val) + return ret_val; + } else { + /* Configure Master and Slave downshift values */ + phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK | + M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK); + phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X | + M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X); + ret_val = e1000_write_phy_reg(hw, + M88E1000_EXT_PHY_SPEC_CTRL, phy_data); + if (ret_val) + return ret_val; + } } /* SW Reset the PHY so all changes take effect */ @@ -1620,6 +1711,10 @@ e1000_copper_link_autoneg(struct e1000_hw *hw) if(hw->autoneg_advertised == 0) hw->autoneg_advertised = AUTONEG_ADVERTISE_SPEED_DEFAULT; + /* IFE phy only supports 10/100 */ + if (hw->phy_type == e1000_phy_ife) + hw->autoneg_advertised &= AUTONEG_ADVERTISE_10_100_ALL; + DEBUGOUT("Reconfiguring auto-neg advertisement params\n"); ret_val = e1000_phy_setup_autoneg(hw); if(ret_val) { @@ -1717,6 +1812,26 @@ e1000_setup_copper_link(struct e1000_hw *hw) DEBUGFUNC("e1000_setup_copper_link"); + switch (hw->mac_type) { + case e1000_80003es2lan: + case e1000_ich8lan: + /* Set the mac to wait the maximum time between each + * iteration and increase the max iterations when + * polling the phy; this fixes erroneous timeouts at 10Mbps. */ + ret_val = e1000_write_kmrn_reg(hw, GG82563_REG(0x34, 4), 0xFFFF); + if (ret_val) + return ret_val; + ret_val = e1000_read_kmrn_reg(hw, GG82563_REG(0x34, 9), ®_data); + if (ret_val) + return ret_val; + reg_data |= 0x3F; + ret_val = e1000_write_kmrn_reg(hw, GG82563_REG(0x34, 9), reg_data); + if (ret_val) + return ret_val; + default: + break; + } + /* Check if it is a valid PHY and set PHY mode if necessary. */ ret_val = e1000_copper_link_preconfig(hw); if(ret_val) @@ -1724,10 +1839,8 @@ e1000_setup_copper_link(struct e1000_hw *hw) switch (hw->mac_type) { case e1000_80003es2lan: - ret_val = e1000_read_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_INB_CTRL, - ®_data); - if (ret_val) - return ret_val; + /* Kumeran registers are written-only */ + reg_data = E1000_KUMCTRLSTA_INB_CTRL_LINK_STATUS_TX_TIMEOUT_DEFAULT; reg_data |= E1000_KUMCTRLSTA_INB_CTRL_DIS_PADDING; ret_val = e1000_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_INB_CTRL, reg_data); @@ -1739,6 +1852,7 @@ e1000_setup_copper_link(struct e1000_hw *hw) } if (hw->phy_type == e1000_phy_igp || + hw->phy_type == e1000_phy_igp_3 || hw->phy_type == e1000_phy_igp_2) { ret_val = e1000_copper_link_igp_setup(hw); if(ret_val) @@ -1803,7 +1917,7 @@ e1000_setup_copper_link(struct e1000_hw *hw) * hw - Struct containing variables accessed by shared code ******************************************************************************/ static int32_t -e1000_configure_kmrn_for_10_100(struct e1000_hw *hw) +e1000_configure_kmrn_for_10_100(struct e1000_hw *hw, uint16_t duplex) { int32_t ret_val = E1000_SUCCESS; uint32_t tipg; @@ -1823,6 +1937,18 @@ e1000_configure_kmrn_for_10_100(struct e1000_hw *hw) tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_10_100; E1000_WRITE_REG(hw, TIPG, tipg); + ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data); + + if (ret_val) + return ret_val; + + if (duplex == HALF_DUPLEX) + reg_data |= GG82563_KMCR_PASS_FALSE_CARRIER; + else + reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; + + ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data); + return ret_val; } @@ -1847,6 +1973,14 @@ e1000_configure_kmrn_for_1000(struct e1000_hw *hw) tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_1000; E1000_WRITE_REG(hw, TIPG, tipg); + ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data); + + if (ret_val) + return ret_val; + + reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; + ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data); + return ret_val; } @@ -1869,10 +2003,13 @@ e1000_phy_setup_autoneg(struct e1000_hw *hw) if(ret_val) return ret_val; - /* Read the MII 1000Base-T Control Register (Address 9). */ - ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg); - if(ret_val) - return ret_val; + if (hw->phy_type != e1000_phy_ife) { + /* Read the MII 1000Base-T Control Register (Address 9). */ + ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg); + if (ret_val) + return ret_val; + } else + mii_1000t_ctrl_reg=0; /* Need to parse both autoneg_advertised and fc and set up * the appropriate PHY registers. First we will parse for @@ -1923,6 +2060,9 @@ e1000_phy_setup_autoneg(struct e1000_hw *hw) if(hw->autoneg_advertised & ADVERTISE_1000_FULL) { DEBUGOUT("Advertise 1000mb Full duplex\n"); mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS; + if (hw->phy_type == e1000_phy_ife) { + DEBUGOUT("e1000_phy_ife is a 10/100 PHY. Gigabit speed is not supported.\n"); + } } /* Check for a software override of the flow control settings, and @@ -1984,9 +2124,11 @@ e1000_phy_setup_autoneg(struct e1000_hw *hw) DEBUGOUT1("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg); - ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg); - if(ret_val) - return ret_val; + if (hw->phy_type != e1000_phy_ife) { + ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg); + if (ret_val) + return ret_val; + } return E1000_SUCCESS; } @@ -2089,6 +2231,18 @@ e1000_phy_force_speed_duplex(struct e1000_hw *hw) /* Need to reset the PHY or these changes will be ignored */ mii_ctrl_reg |= MII_CR_RESET; + /* Disable MDI-X support for 10/100 */ + } else if (hw->phy_type == e1000_phy_ife) { + ret_val = e1000_read_phy_reg(hw, IFE_PHY_MDIX_CONTROL, &phy_data); + if (ret_val) + return ret_val; + + phy_data &= ~IFE_PMC_AUTO_MDIX; + phy_data &= ~IFE_PMC_FORCE_MDIX; + + ret_val = e1000_write_phy_reg(hw, IFE_PHY_MDIX_CONTROL, phy_data); + if (ret_val) + return ret_val; } else { /* Clear Auto-Crossover to force MDI manually. IGP requires MDI * forced whenever speed or duplex are forced. @@ -2721,8 +2875,12 @@ e1000_check_for_link(struct e1000_hw *hw) */ if(hw->tbi_compatibility_en) { uint16_t speed, duplex; - e1000_get_speed_and_duplex(hw, &speed, &duplex); - if(speed != SPEED_1000) { + ret_val = e1000_get_speed_and_duplex(hw, &speed, &duplex); + if (ret_val) { + DEBUGOUT("Error getting link speed and duplex\n"); + return ret_val; + } + if (speed != SPEED_1000) { /* If link speed is not set to gigabit speed, we do not need * to enable TBI compatibility. */ @@ -2889,7 +3047,13 @@ e1000_get_speed_and_duplex(struct e1000_hw *hw, if (*speed == SPEED_1000) ret_val = e1000_configure_kmrn_for_1000(hw); else - ret_val = e1000_configure_kmrn_for_10_100(hw); + ret_val = e1000_configure_kmrn_for_10_100(hw, *duplex); + if (ret_val) + return ret_val; + } + + if ((hw->phy_type == e1000_phy_igp_3) && (*speed == SPEED_1000)) { + ret_val = e1000_kumeran_lock_loss_workaround(hw); if (ret_val) return ret_val; } @@ -3079,6 +3243,9 @@ e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask) DEBUGFUNC("e1000_swfw_sync_acquire"); + if (hw->swfwhw_semaphore_present) + return e1000_get_software_flag(hw); + if (!hw->swfw_sync_present) return e1000_get_hw_eeprom_semaphore(hw); @@ -3118,6 +3285,11 @@ e1000_swfw_sync_release(struct e1000_hw *hw, uint16_t mask) DEBUGFUNC("e1000_swfw_sync_release"); + if (hw->swfwhw_semaphore_present) { + e1000_release_software_flag(hw); + return; + } + if (!hw->swfw_sync_present) { e1000_put_hw_eeprom_semaphore(hw); return; @@ -3160,7 +3332,8 @@ e1000_read_phy_reg(struct e1000_hw *hw, if (e1000_swfw_sync_acquire(hw, swfw)) return -E1000_ERR_SWFW_SYNC; - if((hw->phy_type == e1000_phy_igp || + if ((hw->phy_type == e1000_phy_igp || + hw->phy_type == e1000_phy_igp_3 || hw->phy_type == e1000_phy_igp_2) && (reg_addr > MAX_PHY_MULTI_PAGE_REG)) { ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT, @@ -3299,7 +3472,8 @@ e1000_write_phy_reg(struct e1000_hw *hw, if (e1000_swfw_sync_acquire(hw, swfw)) return -E1000_ERR_SWFW_SYNC; - if((hw->phy_type == e1000_phy_igp || + if ((hw->phy_type == e1000_phy_igp || + hw->phy_type == e1000_phy_igp_3 || hw->phy_type == e1000_phy_igp_2) && (reg_addr > MAX_PHY_MULTI_PAGE_REG)) { ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT, @@ -3514,7 +3688,7 @@ e1000_phy_hw_reset(struct e1000_hw *hw) E1000_WRITE_FLUSH(hw); if (hw->mac_type >= e1000_82571) - msec_delay(10); + msec_delay_irq(10); e1000_swfw_sync_release(hw, swfw); } else { /* Read the Extended Device Control Register, assert the PHY_RESET_DIR @@ -3544,6 +3718,12 @@ e1000_phy_hw_reset(struct e1000_hw *hw) ret_val = e1000_get_phy_cfg_done(hw); e1000_release_software_semaphore(hw); + if ((hw->mac_type == e1000_ich8lan) && + (hw->phy_type == e1000_phy_igp_3)) { + ret_val = e1000_init_lcd_from_nvm(hw); + if (ret_val) + return ret_val; + } return ret_val; } @@ -3572,9 +3752,11 @@ e1000_phy_reset(struct e1000_hw *hw) case e1000_82541_rev_2: case e1000_82571: case e1000_82572: + case e1000_ich8lan: ret_val = e1000_phy_hw_reset(hw); if(ret_val) return ret_val; + break; default: ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data); @@ -3596,12 +3778,121 @@ e1000_phy_reset(struct e1000_hw *hw) return E1000_SUCCESS; } +/****************************************************************************** +* Work-around for 82566 power-down: on D3 entry- +* 1) disable gigabit link +* 2) write VR power-down enable +* 3) read it back +* if successful continue, else issue LCD reset and repeat +* +* hw - struct containing variables accessed by shared code +******************************************************************************/ +void +e1000_phy_powerdown_workaround(struct e1000_hw *hw) +{ + int32_t reg; + uint16_t phy_data; + int32_t retry = 0; + + DEBUGFUNC("e1000_phy_powerdown_workaround"); + + if (hw->phy_type != e1000_phy_igp_3) + return; + + do { + /* Disable link */ + reg = E1000_READ_REG(hw, PHY_CTRL); + E1000_WRITE_REG(hw, PHY_CTRL, reg | E1000_PHY_CTRL_GBE_DISABLE | + E1000_PHY_CTRL_NOND0A_GBE_DISABLE); + + /* Write VR power-down enable */ + e1000_read_phy_reg(hw, IGP3_VR_CTRL, &phy_data); + e1000_write_phy_reg(hw, IGP3_VR_CTRL, phy_data | + IGP3_VR_CTRL_MODE_SHUT); + + /* Read it back and test */ + e1000_read_phy_reg(hw, IGP3_VR_CTRL, &phy_data); + if ((phy_data & IGP3_VR_CTRL_MODE_SHUT) || retry) + break; + + /* Issue PHY reset and repeat at most one more time */ + reg = E1000_READ_REG(hw, CTRL); + E1000_WRITE_REG(hw, CTRL, reg | E1000_CTRL_PHY_RST); + retry++; + } while (retry); + + return; + +} + +/****************************************************************************** +* Work-around for 82566 Kumeran PCS lock loss: +* On link status change (i.e. PCI reset, speed change) and link is up and +* speed is gigabit- +* 0) if workaround is optionally disabled do nothing +* 1) wait 1ms for Kumeran link to come up +* 2) check Kumeran Diagnostic register PCS lock loss bit +* 3) if not set the link is locked (all is good), otherwise... +* 4) reset the PHY +* 5) repeat up to 10 times +* Note: this is only called for IGP3 copper when speed is 1gb. +* +* hw - struct containing variables accessed by shared code +******************************************************************************/ +int32_t +e1000_kumeran_lock_loss_workaround(struct e1000_hw *hw) +{ + int32_t ret_val; + int32_t reg; + int32_t cnt; + uint16_t phy_data; + + if (hw->kmrn_lock_loss_workaround_disabled) + return E1000_SUCCESS; + + /* Make sure link is up before proceeding. If not just return. + * Attempting this while link is negotiating fouls up link + * stability */ + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); + + if (phy_data & MII_SR_LINK_STATUS) { + for (cnt = 0; cnt < 10; cnt++) { + /* read once to clear */ + ret_val = e1000_read_phy_reg(hw, IGP3_KMRN_DIAG, &phy_data); + if (ret_val) + return ret_val; + /* and again to get new status */ + ret_val = e1000_read_phy_reg(hw, IGP3_KMRN_DIAG, &phy_data); + if (ret_val) + return ret_val; + + /* check for PCS lock */ + if (!(phy_data & IGP3_KMRN_DIAG_PCS_LOCK_LOSS)) + return E1000_SUCCESS; + + /* Issue PHY reset */ + e1000_phy_hw_reset(hw); + msec_delay_irq(5); + } + /* Disable GigE link negotiation */ + reg = E1000_READ_REG(hw, PHY_CTRL); + E1000_WRITE_REG(hw, PHY_CTRL, reg | E1000_PHY_CTRL_GBE_DISABLE | + E1000_PHY_CTRL_NOND0A_GBE_DISABLE); + + /* unable to acquire PCS lock */ + return E1000_ERR_PHY; + } + + return E1000_SUCCESS; +} + /****************************************************************************** * Probes the expected PHY address for known PHY IDs * * hw - Struct containing variables accessed by shared code ******************************************************************************/ -static int32_t +int32_t e1000_detect_gig_phy(struct e1000_hw *hw) { int32_t phy_init_status, ret_val; @@ -3613,8 +3904,8 @@ e1000_detect_gig_phy(struct e1000_hw *hw) /* The 82571 firmware may still be configuring the PHY. In this * case, we cannot access the PHY until the configuration is done. So * we explicitly set the PHY values. */ - if(hw->mac_type == e1000_82571 || - hw->mac_type == e1000_82572) { + if (hw->mac_type == e1000_82571 || + hw->mac_type == e1000_82572) { hw->phy_id = IGP01E1000_I_PHY_ID; hw->phy_type = e1000_phy_igp_2; return E1000_SUCCESS; @@ -3631,7 +3922,7 @@ e1000_detect_gig_phy(struct e1000_hw *hw) /* Read the PHY ID Registers to identify which PHY is onboard. */ ret_val = e1000_read_phy_reg(hw, PHY_ID1, &phy_id_high); - if(ret_val) + if (ret_val) return ret_val; hw->phy_id = (uint32_t) (phy_id_high << 16); @@ -3669,6 +3960,12 @@ e1000_detect_gig_phy(struct e1000_hw *hw) case e1000_80003es2lan: if (hw->phy_id == GG82563_E_PHY_ID) match = TRUE; break; + case e1000_ich8lan: + if (hw->phy_id == IGP03E1000_E_PHY_ID) match = TRUE; + if (hw->phy_id == IFE_E_PHY_ID) match = TRUE; + if (hw->phy_id == IFE_PLUS_E_PHY_ID) match = TRUE; + if (hw->phy_id == IFE_C_E_PHY_ID) match = TRUE; + break; default: DEBUGOUT1("Invalid MAC type %d\n", hw->mac_type); return -E1000_ERR_CONFIG; @@ -3783,6 +4080,53 @@ e1000_phy_igp_get_info(struct e1000_hw *hw, return E1000_SUCCESS; } +/****************************************************************************** +* Get PHY information from various PHY registers for ife PHY only. +* +* hw - Struct containing variables accessed by shared code +* phy_info - PHY information structure +******************************************************************************/ +int32_t +e1000_phy_ife_get_info(struct e1000_hw *hw, + struct e1000_phy_info *phy_info) +{ + int32_t ret_val; + uint16_t phy_data, polarity; + + DEBUGFUNC("e1000_phy_ife_get_info"); + + phy_info->downshift = (e1000_downshift)hw->speed_downgraded; + phy_info->extended_10bt_distance = e1000_10bt_ext_dist_enable_normal; + + ret_val = e1000_read_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL, &phy_data); + if (ret_val) + return ret_val; + phy_info->polarity_correction = + (phy_data & IFE_PSC_AUTO_POLARITY_DISABLE) >> + IFE_PSC_AUTO_POLARITY_DISABLE_SHIFT; + + if (phy_info->polarity_correction == e1000_polarity_reversal_enabled) { + ret_val = e1000_check_polarity(hw, &polarity); + if (ret_val) + return ret_val; + } else { + /* Polarity is forced. */ + polarity = (phy_data & IFE_PSC_FORCE_POLARITY) >> + IFE_PSC_FORCE_POLARITY_SHIFT; + } + phy_info->cable_polarity = polarity; + + ret_val = e1000_read_phy_reg(hw, IFE_PHY_MDIX_CONTROL, &phy_data); + if (ret_val) + return ret_val; + + phy_info->mdix_mode = + (phy_data & (IFE_PMC_AUTO_MDIX | IFE_PMC_FORCE_MDIX)) >> + IFE_PMC_MDIX_MODE_SHIFT; + + return E1000_SUCCESS; +} + /****************************************************************************** * Get PHY information from various PHY registers fot m88 PHY only. * @@ -3898,9 +4242,12 @@ e1000_phy_get_info(struct e1000_hw *hw, return -E1000_ERR_CONFIG; } - if(hw->phy_type == e1000_phy_igp || + if (hw->phy_type == e1000_phy_igp || + hw->phy_type == e1000_phy_igp_3 || hw->phy_type == e1000_phy_igp_2) return e1000_phy_igp_get_info(hw, phy_info); + else if (hw->phy_type == e1000_phy_ife) + return e1000_phy_ife_get_info(hw, phy_info); else return e1000_phy_m88_get_info(hw, phy_info); } @@ -4049,6 +4396,35 @@ e1000_init_eeprom_params(struct e1000_hw *hw) eeprom->use_eerd = TRUE; eeprom->use_eewr = FALSE; break; + case e1000_ich8lan: + { + int32_t i = 0; + uint32_t flash_size = E1000_READ_ICH8_REG(hw, ICH8_FLASH_GFPREG); + + eeprom->type = e1000_eeprom_ich8; + eeprom->use_eerd = FALSE; + eeprom->use_eewr = FALSE; + eeprom->word_size = E1000_SHADOW_RAM_WORDS; + + /* Zero the shadow RAM structure. But don't load it from NVM + * so as to save time for driver init */ + if (hw->eeprom_shadow_ram != NULL) { + for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) { + hw->eeprom_shadow_ram[i].modified = FALSE; + hw->eeprom_shadow_ram[i].eeprom_word = 0xFFFF; + } + } + + hw->flash_base_addr = (flash_size & ICH8_GFPREG_BASE_MASK) * + ICH8_FLASH_SECTOR_SIZE; + + hw->flash_bank_size = ((flash_size >> 16) & ICH8_GFPREG_BASE_MASK) + 1; + hw->flash_bank_size -= (flash_size & ICH8_GFPREG_BASE_MASK); + hw->flash_bank_size *= ICH8_FLASH_SECTOR_SIZE; + hw->flash_bank_size /= 2 * sizeof(uint16_t); + + break; + } default: break; } @@ -4469,7 +4845,10 @@ e1000_read_eeprom(struct e1000_hw *hw, return ret_val; } - if(eeprom->type == e1000_eeprom_spi) { + if (eeprom->type == e1000_eeprom_ich8) + return e1000_read_eeprom_ich8(hw, offset, words, data); + + if (eeprom->type == e1000_eeprom_spi) { uint16_t word_in; uint8_t read_opcode = EEPROM_READ_OPCODE_SPI; @@ -4636,7 +5015,10 @@ e1000_is_onboard_nvm_eeprom(struct e1000_hw *hw) DEBUGFUNC("e1000_is_onboard_nvm_eeprom"); - if(hw->mac_type == e1000_82573) { + if (hw->mac_type == e1000_ich8lan) + return FALSE; + + if (hw->mac_type == e1000_82573) { eecd = E1000_READ_REG(hw, EECD); /* Isolate bits 15 & 16 */ @@ -4686,8 +5068,22 @@ e1000_validate_eeprom_checksum(struct e1000_hw *hw) } } - for(i = 0; i < (EEPROM_CHECKSUM_REG + 1); i++) { - if(e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) { + if (hw->mac_type == e1000_ich8lan) { + /* Drivers must allocate the shadow ram structure for the + * EEPROM checksum to be updated. Otherwise, this bit as well + * as the checksum must both be set correctly for this + * validation to pass. + */ + e1000_read_eeprom(hw, 0x19, 1, &eeprom_data); + if ((eeprom_data & 0x40) == 0) { + eeprom_data |= 0x40; + e1000_write_eeprom(hw, 0x19, 1, &eeprom_data); + e1000_update_eeprom_checksum(hw); + } + } + + for (i = 0; i < (EEPROM_CHECKSUM_REG + 1); i++) { + if (e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) { DEBUGOUT("EEPROM Read Error\n"); return -E1000_ERR_EEPROM; } @@ -4713,6 +5109,7 @@ e1000_validate_eeprom_checksum(struct e1000_hw *hw) int32_t e1000_update_eeprom_checksum(struct e1000_hw *hw) { + uint32_t ctrl_ext; uint16_t checksum = 0; uint16_t i, eeprom_data; @@ -4731,6 +5128,14 @@ e1000_update_eeprom_checksum(struct e1000_hw *hw) return -E1000_ERR_EEPROM; } else if (hw->eeprom.type == e1000_eeprom_flash) { e1000_commit_shadow_ram(hw); + } else if (hw->eeprom.type == e1000_eeprom_ich8) { + e1000_commit_shadow_ram(hw); + /* Reload the EEPROM, or else modifications will not appear + * until after next adapter reset. */ + ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); + ctrl_ext |= E1000_CTRL_EXT_EE_RST; + E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); + msec_delay(10); } return E1000_SUCCESS; } @@ -4770,6 +5175,9 @@ e1000_write_eeprom(struct e1000_hw *hw, if(eeprom->use_eewr == TRUE) return e1000_write_eeprom_eewr(hw, offset, words, data); + if (eeprom->type == e1000_eeprom_ich8) + return e1000_write_eeprom_ich8(hw, offset, words, data); + /* Prepare the EEPROM for writing */ if (e1000_acquire_eeprom(hw) != E1000_SUCCESS) return -E1000_ERR_EEPROM; @@ -4957,11 +5365,17 @@ e1000_commit_shadow_ram(struct e1000_hw *hw) uint32_t flop = 0; uint32_t i = 0; int32_t error = E1000_SUCCESS; - - /* The flop register will be used to determine if flash type is STM */ - flop = E1000_READ_REG(hw, FLOP); + uint32_t old_bank_offset = 0; + uint32_t new_bank_offset = 0; + uint32_t sector_retries = 0; + uint8_t low_byte = 0; + uint8_t high_byte = 0; + uint8_t temp_byte = 0; + boolean_t sector_write_failed = FALSE; if (hw->mac_type == e1000_82573) { + /* The flop register will be used to determine if flash type is STM */ + flop = E1000_READ_REG(hw, FLOP); for (i=0; i < attempts; i++) { eecd = E1000_READ_REG(hw, EECD); if ((eecd & E1000_EECD_FLUPD) == 0) { @@ -4995,6 +5409,106 @@ e1000_commit_shadow_ram(struct e1000_hw *hw) } } + if (hw->mac_type == e1000_ich8lan && hw->eeprom_shadow_ram != NULL) { + /* We're writing to the opposite bank so if we're on bank 1, + * write to bank 0 etc. We also need to erase the segment that + * is going to be written */ + if (!(E1000_READ_REG(hw, EECD) & E1000_EECD_SEC1VAL)) { + new_bank_offset = hw->flash_bank_size * 2; + old_bank_offset = 0; + e1000_erase_ich8_4k_segment(hw, 1); + } else { + old_bank_offset = hw->flash_bank_size * 2; + new_bank_offset = 0; + e1000_erase_ich8_4k_segment(hw, 0); + } + + do { + sector_write_failed = FALSE; + /* Loop for every byte in the shadow RAM, + * which is in units of words. */ + for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) { + /* Determine whether to write the value stored + * in the other NVM bank or a modified value stored + * in the shadow RAM */ + if (hw->eeprom_shadow_ram[i].modified == TRUE) { + low_byte = (uint8_t)hw->eeprom_shadow_ram[i].eeprom_word; + e1000_read_ich8_byte(hw, (i << 1) + old_bank_offset, + &temp_byte); + udelay(100); + error = e1000_verify_write_ich8_byte(hw, + (i << 1) + new_bank_offset, + low_byte); + if (error != E1000_SUCCESS) + sector_write_failed = TRUE; + high_byte = + (uint8_t)(hw->eeprom_shadow_ram[i].eeprom_word >> 8); + e1000_read_ich8_byte(hw, (i << 1) + old_bank_offset + 1, + &temp_byte); + udelay(100); + } else { + e1000_read_ich8_byte(hw, (i << 1) + old_bank_offset, + &low_byte); + udelay(100); + error = e1000_verify_write_ich8_byte(hw, + (i << 1) + new_bank_offset, low_byte); + if (error != E1000_SUCCESS) + sector_write_failed = TRUE; + e1000_read_ich8_byte(hw, (i << 1) + old_bank_offset + 1, + &high_byte); + } + + /* If the word is 0x13, then make sure the signature bits + * (15:14) are 11b until the commit has completed. + * This will allow us to write 10b which indicates the + * signature is valid. We want to do this after the write + * has completed so that we don't mark the segment valid + * while the write is still in progress */ + if (i == E1000_ICH8_NVM_SIG_WORD) + high_byte = E1000_ICH8_NVM_SIG_MASK | high_byte; + + error = e1000_verify_write_ich8_byte(hw, + (i << 1) + new_bank_offset + 1, high_byte); + if (error != E1000_SUCCESS) + sector_write_failed = TRUE; + + if (sector_write_failed == FALSE) { + /* Clear the now not used entry in the cache */ + hw->eeprom_shadow_ram[i].modified = FALSE; + hw->eeprom_shadow_ram[i].eeprom_word = 0xFFFF; + } + } + + /* Don't bother writing the segment valid bits if sector + * programming failed. */ + if (sector_write_failed == FALSE) { + /* Finally validate the new segment by setting bit 15:14 + * to 10b in word 0x13 , this can be done without an + * erase as well since these bits are 11 to start with + * and we need to change bit 14 to 0b */ + e1000_read_ich8_byte(hw, + E1000_ICH8_NVM_SIG_WORD * 2 + 1 + new_bank_offset, + &high_byte); + high_byte &= 0xBF; + error = e1000_verify_write_ich8_byte(hw, + E1000_ICH8_NVM_SIG_WORD * 2 + 1 + new_bank_offset, + high_byte); + if (error != E1000_SUCCESS) + sector_write_failed = TRUE; + + /* And invalidate the previously valid segment by setting + * its signature word (0x13) high_byte to 0b. This can be + * done without an erase because flash erase sets all bits + * to 1's. We can write 1's to 0's without an erase */ + error = e1000_verify_write_ich8_byte(hw, + E1000_ICH8_NVM_SIG_WORD * 2 + 1 + old_bank_offset, + 0); + if (error != E1000_SUCCESS) + sector_write_failed = TRUE; + } + } while (++sector_retries < 10 && sector_write_failed == TRUE); + } + return error; } @@ -5102,15 +5616,19 @@ e1000_init_rx_addrs(struct e1000_hw *hw) * the other port. */ if ((hw->mac_type == e1000_82571) && (hw->laa_is_present == TRUE)) rar_num -= 1; + if (hw->mac_type == e1000_ich8lan) + rar_num = E1000_RAR_ENTRIES_ICH8LAN; + /* Zero out the other 15 receive addresses. */ DEBUGOUT("Clearing RAR[1-15]\n"); for(i = 1; i < rar_num; i++) { E1000_WRITE_REG_ARRAY(hw, RA, (i << 1), 0); + E1000_WRITE_FLUSH(hw); E1000_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0); + E1000_WRITE_FLUSH(hw); } } -#if 0 /****************************************************************************** * Updates the MAC's list of multicast addresses. * @@ -5145,6 +5663,8 @@ e1000_mc_addr_list_update(struct e1000_hw *hw, /* Clear RAR[1-15] */ DEBUGOUT(" Clearing RAR[1-15]\n"); num_rar_entry = E1000_RAR_ENTRIES; + if (hw->mac_type == e1000_ich8lan) + num_rar_entry = E1000_RAR_ENTRIES_ICH8LAN; /* Reserve a spot for the Locally Administered Address to work around * an 82571 issue in which a reset on one port will reload the MAC on * the other port. */ @@ -5153,14 +5673,19 @@ e1000_mc_addr_list_update(struct e1000_hw *hw, for(i = rar_used_count; i < num_rar_entry; i++) { E1000_WRITE_REG_ARRAY(hw, RA, (i << 1), 0); + E1000_WRITE_FLUSH(hw); E1000_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0); + E1000_WRITE_FLUSH(hw); } /* Clear the MTA */ DEBUGOUT(" Clearing MTA\n"); num_mta_entry = E1000_NUM_MTA_REGISTERS; + if (hw->mac_type == e1000_ich8lan) + num_mta_entry = E1000_NUM_MTA_REGISTERS_ICH8LAN; for(i = 0; i < num_mta_entry; i++) { E1000_WRITE_REG_ARRAY(hw, MTA, i, 0); + E1000_WRITE_FLUSH(hw); } /* Add the new addresses */ @@ -5194,7 +5719,6 @@ e1000_mc_addr_list_update(struct e1000_hw *hw, } DEBUGOUT("MC Update Complete\n"); } -#endif /* 0 */ /****************************************************************************** * Hashes an address to determine its location in the multicast table @@ -5217,24 +5741,46 @@ e1000_hash_mc_addr(struct e1000_hw *hw, * LSB MSB */ case 0: - /* [47:36] i.e. 0x563 for above example address */ - hash_value = ((mc_addr[4] >> 4) | (((uint16_t) mc_addr[5]) << 4)); + if (hw->mac_type == e1000_ich8lan) { + /* [47:38] i.e. 0x158 for above example address */ + hash_value = ((mc_addr[4] >> 6) | (((uint16_t) mc_addr[5]) << 2)); + } else { + /* [47:36] i.e. 0x563 for above example address */ + hash_value = ((mc_addr[4] >> 4) | (((uint16_t) mc_addr[5]) << 4)); + } break; case 1: - /* [46:35] i.e. 0xAC6 for above example address */ - hash_value = ((mc_addr[4] >> 3) | (((uint16_t) mc_addr[5]) << 5)); + if (hw->mac_type == e1000_ich8lan) { + /* [46:37] i.e. 0x2B1 for above example address */ + hash_value = ((mc_addr[4] >> 5) | (((uint16_t) mc_addr[5]) << 3)); + } else { + /* [46:35] i.e. 0xAC6 for above example address */ + hash_value = ((mc_addr[4] >> 3) | (((uint16_t) mc_addr[5]) << 5)); + } break; case 2: - /* [45:34] i.e. 0x5D8 for above example address */ - hash_value = ((mc_addr[4] >> 2) | (((uint16_t) mc_addr[5]) << 6)); + if (hw->mac_type == e1000_ich8lan) { + /*[45:36] i.e. 0x163 for above example address */ + hash_value = ((mc_addr[4] >> 4) | (((uint16_t) mc_addr[5]) << 4)); + } else { + /* [45:34] i.e. 0x5D8 for above example address */ + hash_value = ((mc_addr[4] >> 2) | (((uint16_t) mc_addr[5]) << 6)); + } break; case 3: - /* [43:32] i.e. 0x634 for above example address */ - hash_value = ((mc_addr[4]) | (((uint16_t) mc_addr[5]) << 8)); + if (hw->mac_type == e1000_ich8lan) { + /* [43:34] i.e. 0x18D for above example address */ + hash_value = ((mc_addr[4] >> 2) | (((uint16_t) mc_addr[5]) << 6)); + } else { + /* [43:32] i.e. 0x634 for above example address */ + hash_value = ((mc_addr[4]) | (((uint16_t) mc_addr[5]) << 8)); + } break; } hash_value &= 0xFFF; + if (hw->mac_type == e1000_ich8lan) + hash_value &= 0x3FF; return hash_value; } @@ -5262,6 +5808,8 @@ e1000_mta_set(struct e1000_hw *hw, * register are determined by the lower 5 bits of the value. */ hash_reg = (hash_value >> 5) & 0x7F; + if (hw->mac_type == e1000_ich8lan) + hash_reg &= 0x1F; hash_bit = hash_value & 0x1F; mta = E1000_READ_REG_ARRAY(hw, MTA, hash_reg); @@ -5275,9 +5823,12 @@ e1000_mta_set(struct e1000_hw *hw, if((hw->mac_type == e1000_82544) && ((hash_reg & 0x1) == 1)) { temp = E1000_READ_REG_ARRAY(hw, MTA, (hash_reg - 1)); E1000_WRITE_REG_ARRAY(hw, MTA, hash_reg, mta); + E1000_WRITE_FLUSH(hw); E1000_WRITE_REG_ARRAY(hw, MTA, (hash_reg - 1), temp); + E1000_WRITE_FLUSH(hw); } else { E1000_WRITE_REG_ARRAY(hw, MTA, hash_reg, mta); + E1000_WRITE_FLUSH(hw); } } @@ -5334,7 +5885,9 @@ e1000_rar_set(struct e1000_hw *hw, } E1000_WRITE_REG_ARRAY(hw, RA, (index << 1), rar_low); + E1000_WRITE_FLUSH(hw); E1000_WRITE_REG_ARRAY(hw, RA, ((index << 1) + 1), rar_high); + E1000_WRITE_FLUSH(hw); } /****************************************************************************** @@ -5351,12 +5904,18 @@ e1000_write_vfta(struct e1000_hw *hw, { uint32_t temp; - if((hw->mac_type == e1000_82544) && ((offset & 0x1) == 1)) { + if (hw->mac_type == e1000_ich8lan) + return; + + if ((hw->mac_type == e1000_82544) && ((offset & 0x1) == 1)) { temp = E1000_READ_REG_ARRAY(hw, VFTA, (offset - 1)); E1000_WRITE_REG_ARRAY(hw, VFTA, offset, value); + E1000_WRITE_FLUSH(hw); E1000_WRITE_REG_ARRAY(hw, VFTA, (offset - 1), temp); + E1000_WRITE_FLUSH(hw); } else { E1000_WRITE_REG_ARRAY(hw, VFTA, offset, value); + E1000_WRITE_FLUSH(hw); } } @@ -5373,6 +5932,9 @@ e1000_clear_vfta(struct e1000_hw *hw) uint32_t vfta_offset = 0; uint32_t vfta_bit_in_reg = 0; + if (hw->mac_type == e1000_ich8lan) + return; + if (hw->mac_type == e1000_82573) { if (hw->mng_cookie.vlan_id != 0) { /* The VFTA is a 4096b bit-field, each identifying a single VLAN @@ -5392,6 +5954,7 @@ e1000_clear_vfta(struct e1000_hw *hw) * manageability unit */ vfta_value = (offset == vfta_offset) ? vfta_bit_in_reg : 0; E1000_WRITE_REG_ARRAY(hw, VFTA, offset, vfta_value); + E1000_WRITE_FLUSH(hw); } } @@ -5421,9 +5984,18 @@ e1000_id_led_init(struct e1000_hw * hw) DEBUGOUT("EEPROM Read Error\n"); return -E1000_ERR_EEPROM; } - if((eeprom_data== ID_LED_RESERVED_0000) || - (eeprom_data == ID_LED_RESERVED_FFFF)) eeprom_data = ID_LED_DEFAULT; - for(i = 0; i < 4; i++) { + + if ((hw->mac_type == e1000_82573) && + (eeprom_data == ID_LED_RESERVED_82573)) + eeprom_data = ID_LED_DEFAULT_82573; + else if ((eeprom_data == ID_LED_RESERVED_0000) || + (eeprom_data == ID_LED_RESERVED_FFFF)) { + if (hw->mac_type == e1000_ich8lan) + eeprom_data = ID_LED_DEFAULT_ICH8LAN; + else + eeprom_data = ID_LED_DEFAULT; + } + for (i = 0; i < 4; i++) { temp = (eeprom_data >> (i << 2)) & led_mask; switch(temp) { case ID_LED_ON1_DEF2: @@ -5518,6 +6090,44 @@ e1000_setup_led(struct e1000_hw *hw) return E1000_SUCCESS; } +/****************************************************************************** + * Used on 82571 and later Si that has LED blink bits. + * Callers must use their own timer and should have already called + * e1000_id_led_init() + * Call e1000_cleanup led() to stop blinking + * + * hw - Struct containing variables accessed by shared code + *****************************************************************************/ +int32_t +e1000_blink_led_start(struct e1000_hw *hw) +{ + int16_t i; + uint32_t ledctl_blink = 0; + + DEBUGFUNC("e1000_id_led_blink_on"); + + if (hw->mac_type < e1000_82571) { + /* Nothing to do */ + return E1000_SUCCESS; + } + if (hw->media_type == e1000_media_type_fiber) { + /* always blink LED0 for PCI-E fiber */ + ledctl_blink = E1000_LEDCTL_LED0_BLINK | + (E1000_LEDCTL_MODE_LED_ON << E1000_LEDCTL_LED0_MODE_SHIFT); + } else { + /* set the blink bit for each LED that's "on" (0x0E) in ledctl_mode2 */ + ledctl_blink = hw->ledctl_mode2; + for (i=0; i < 4; i++) + if (((hw->ledctl_mode2 >> (i * 8)) & 0xFF) == + E1000_LEDCTL_MODE_LED_ON) + ledctl_blink |= (E1000_LEDCTL_LED0_BLINK << (i * 8)); + } + + E1000_WRITE_REG(hw, LEDCTL, ledctl_blink); + + return E1000_SUCCESS; +} + /****************************************************************************** * Restores the saved state of the SW controlable LED. * @@ -5548,6 +6158,10 @@ e1000_cleanup_led(struct e1000_hw *hw) return ret_val; /* Fall Through */ default: + if (hw->phy_type == e1000_phy_ife) { + e1000_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL_LED, 0); + break; + } /* Restore LEDCTL settings */ E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_default); break; @@ -5592,7 +6206,10 @@ e1000_led_on(struct e1000_hw *hw) /* Clear SW Defineable Pin 0 to turn on the LED */ ctrl &= ~E1000_CTRL_SWDPIN0; ctrl |= E1000_CTRL_SWDPIO0; - } else if(hw->media_type == e1000_media_type_copper) { + } else if (hw->phy_type == e1000_phy_ife) { + e1000_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL_LED, + (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_ON)); + } else if (hw->media_type == e1000_media_type_copper) { E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_mode2); return E1000_SUCCESS; } @@ -5640,7 +6257,10 @@ e1000_led_off(struct e1000_hw *hw) /* Set SW Defineable Pin 0 to turn off the LED */ ctrl |= E1000_CTRL_SWDPIN0; ctrl |= E1000_CTRL_SWDPIO0; - } else if(hw->media_type == e1000_media_type_copper) { + } else if (hw->phy_type == e1000_phy_ife) { + e1000_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL_LED, + (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_OFF)); + } else if (hw->media_type == e1000_media_type_copper) { E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_mode1); return E1000_SUCCESS; } @@ -5678,12 +6298,16 @@ e1000_clear_hw_cntrs(struct e1000_hw *hw) temp = E1000_READ_REG(hw, XOFFRXC); temp = E1000_READ_REG(hw, XOFFTXC); temp = E1000_READ_REG(hw, FCRUC); + + if (hw->mac_type != e1000_ich8lan) { temp = E1000_READ_REG(hw, PRC64); temp = E1000_READ_REG(hw, PRC127); temp = E1000_READ_REG(hw, PRC255); temp = E1000_READ_REG(hw, PRC511); temp = E1000_READ_REG(hw, PRC1023); temp = E1000_READ_REG(hw, PRC1522); + } + temp = E1000_READ_REG(hw, GPRC); temp = E1000_READ_REG(hw, BPRC); temp = E1000_READ_REG(hw, MPRC); @@ -5703,12 +6327,16 @@ e1000_clear_hw_cntrs(struct e1000_hw *hw) temp = E1000_READ_REG(hw, TOTH); temp = E1000_READ_REG(hw, TPR); temp = E1000_READ_REG(hw, TPT); + + if (hw->mac_type != e1000_ich8lan) { temp = E1000_READ_REG(hw, PTC64); temp = E1000_READ_REG(hw, PTC127); temp = E1000_READ_REG(hw, PTC255); temp = E1000_READ_REG(hw, PTC511); temp = E1000_READ_REG(hw, PTC1023); temp = E1000_READ_REG(hw, PTC1522); + } + temp = E1000_READ_REG(hw, MPTC); temp = E1000_READ_REG(hw, BPTC); @@ -5731,6 +6359,9 @@ e1000_clear_hw_cntrs(struct e1000_hw *hw) temp = E1000_READ_REG(hw, IAC); temp = E1000_READ_REG(hw, ICRXOC); + + if (hw->mac_type == e1000_ich8lan) return; + temp = E1000_READ_REG(hw, ICRXPTC); temp = E1000_READ_REG(hw, ICRXATC); temp = E1000_READ_REG(hw, ICTXPTC); @@ -5911,6 +6542,7 @@ e1000_get_bus_info(struct e1000_hw *hw) hw->bus_width = e1000_bus_width_pciex_1; break; case e1000_82571: + case e1000_ich8lan: case e1000_80003es2lan: hw->bus_type = e1000_bus_type_pci_express; hw->bus_speed = e1000_bus_speed_2500; @@ -5948,8 +6580,6 @@ e1000_get_bus_info(struct e1000_hw *hw) break; } } - -#if 0 /****************************************************************************** * Reads a value from one of the devices registers using port I/O (as opposed * memory mapped I/O). Only 82544 and newer devices support port I/O. @@ -5967,7 +6597,6 @@ e1000_read_reg_io(struct e1000_hw *hw, e1000_io_write(hw, io_addr, offset); return e1000_io_read(hw, io_data); } -#endif /* 0 */ /****************************************************************************** * Writes a value to one of the devices registers using port I/O (as opposed to @@ -6012,8 +6641,6 @@ e1000_get_cable_length(struct e1000_hw *hw, { int32_t ret_val; uint16_t agc_value = 0; - uint16_t cur_agc, min_agc = IGP01E1000_AGC_LENGTH_TABLE_SIZE; - uint16_t max_agc = 0; uint16_t i, phy_data; uint16_t cable_length; @@ -6086,6 +6713,8 @@ e1000_get_cable_length(struct e1000_hw *hw, break; } } else if(hw->phy_type == e1000_phy_igp) { /* For IGP PHY */ + uint16_t cur_agc_value; + uint16_t min_agc_value = IGP01E1000_AGC_LENGTH_TABLE_SIZE; uint16_t agc_reg_array[IGP01E1000_PHY_CHANNEL_NUM] = {IGP01E1000_PHY_AGC_A, IGP01E1000_PHY_AGC_B, @@ -6098,23 +6727,23 @@ e1000_get_cable_length(struct e1000_hw *hw, if(ret_val) return ret_val; - cur_agc = phy_data >> IGP01E1000_AGC_LENGTH_SHIFT; + cur_agc_value = phy_data >> IGP01E1000_AGC_LENGTH_SHIFT; - /* Array bound check. */ - if((cur_agc >= IGP01E1000_AGC_LENGTH_TABLE_SIZE - 1) || - (cur_agc == 0)) + /* Value bound check. */ + if ((cur_agc_value >= IGP01E1000_AGC_LENGTH_TABLE_SIZE - 1) || + (cur_agc_value == 0)) return -E1000_ERR_PHY; - agc_value += cur_agc; + agc_value += cur_agc_value; /* Update minimal AGC value. */ - if(min_agc > cur_agc) - min_agc = cur_agc; + if (min_agc_value > cur_agc_value) + min_agc_value = cur_agc_value; } /* Remove the minimal AGC result for length < 50m */ - if(agc_value < IGP01E1000_PHY_CHANNEL_NUM * e1000_igp_cable_length_50) { - agc_value -= min_agc; + if (agc_value < IGP01E1000_PHY_CHANNEL_NUM * e1000_igp_cable_length_50) { + agc_value -= min_agc_value; /* Get the average length of the remaining 3 channels */ agc_value /= (IGP01E1000_PHY_CHANNEL_NUM - 1); @@ -6130,7 +6759,10 @@ e1000_get_cable_length(struct e1000_hw *hw, IGP01E1000_AGC_RANGE) : 0; *max_length = e1000_igp_cable_length_table[agc_value] + IGP01E1000_AGC_RANGE; - } else if (hw->phy_type == e1000_phy_igp_2) { + } else if (hw->phy_type == e1000_phy_igp_2 || + hw->phy_type == e1000_phy_igp_3) { + uint16_t cur_agc_index, max_agc_index = 0; + uint16_t min_agc_index = IGP02E1000_AGC_LENGTH_TABLE_SIZE - 1; uint16_t agc_reg_array[IGP02E1000_PHY_CHANNEL_NUM] = {IGP02E1000_PHY_AGC_A, IGP02E1000_PHY_AGC_B, @@ -6145,19 +6777,27 @@ e1000_get_cable_length(struct e1000_hw *hw, /* Getting bits 15:9, which represent the combination of course and * fine gain values. The result is a number that can be put into * the lookup table to obtain the approximate cable length. */ - cur_agc = (phy_data >> IGP02E1000_AGC_LENGTH_SHIFT) & - IGP02E1000_AGC_LENGTH_MASK; + cur_agc_index = (phy_data >> IGP02E1000_AGC_LENGTH_SHIFT) & + IGP02E1000_AGC_LENGTH_MASK; + + /* Array index bound check. */ + if ((cur_agc_index >= IGP02E1000_AGC_LENGTH_TABLE_SIZE) || + (cur_agc_index == 0)) + return -E1000_ERR_PHY; /* Remove min & max AGC values from calculation. */ - if (e1000_igp_2_cable_length_table[min_agc] > e1000_igp_2_cable_length_table[cur_agc]) - min_agc = cur_agc; - if (e1000_igp_2_cable_length_table[max_agc] < e1000_igp_2_cable_length_table[cur_agc]) - max_agc = cur_agc; + if (e1000_igp_2_cable_length_table[min_agc_index] > + e1000_igp_2_cable_length_table[cur_agc_index]) + min_agc_index = cur_agc_index; + if (e1000_igp_2_cable_length_table[max_agc_index] < + e1000_igp_2_cable_length_table[cur_agc_index]) + max_agc_index = cur_agc_index; - agc_value += e1000_igp_2_cable_length_table[cur_agc]; + agc_value += e1000_igp_2_cable_length_table[cur_agc_index]; } - agc_value -= (e1000_igp_2_cable_length_table[min_agc] + e1000_igp_2_cable_length_table[max_agc]); + agc_value -= (e1000_igp_2_cable_length_table[min_agc_index] + + e1000_igp_2_cable_length_table[max_agc_index]); agc_value /= (IGP02E1000_PHY_CHANNEL_NUM - 2); /* Calculate cable length with the error range of +/- 10 meters. */ @@ -6203,7 +6843,8 @@ e1000_check_polarity(struct e1000_hw *hw, return ret_val; *polarity = (phy_data & M88E1000_PSSR_REV_POLARITY) >> M88E1000_PSSR_REV_POLARITY_SHIFT; - } else if(hw->phy_type == e1000_phy_igp || + } else if (hw->phy_type == e1000_phy_igp || + hw->phy_type == e1000_phy_igp_3 || hw->phy_type == e1000_phy_igp_2) { /* Read the Status register to check the speed */ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS, @@ -6229,6 +6870,13 @@ e1000_check_polarity(struct e1000_hw *hw, * 100 Mbps this bit is always 0) */ *polarity = phy_data & IGP01E1000_PSSR_POLARITY_REVERSED; } + } else if (hw->phy_type == e1000_phy_ife) { + ret_val = e1000_read_phy_reg(hw, IFE_PHY_EXTENDED_STATUS_CONTROL, + &phy_data); + if (ret_val) + return ret_val; + *polarity = (phy_data & IFE_PESC_POLARITY_REVERSED) >> + IFE_PESC_POLARITY_REVERSED_SHIFT; } return E1000_SUCCESS; } @@ -6256,7 +6904,8 @@ e1000_check_downshift(struct e1000_hw *hw) DEBUGFUNC("e1000_check_downshift"); - if(hw->phy_type == e1000_phy_igp || + if (hw->phy_type == e1000_phy_igp || + hw->phy_type == e1000_phy_igp_3 || hw->phy_type == e1000_phy_igp_2) { ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_LINK_HEALTH, &phy_data); @@ -6273,6 +6922,9 @@ e1000_check_downshift(struct e1000_hw *hw) hw->speed_downgraded = (phy_data & M88E1000_PSSR_DOWNSHIFT) >> M88E1000_PSSR_DOWNSHIFT_SHIFT; + } else if (hw->phy_type == e1000_phy_ife) { + /* e1000_phy_ife supports 10/100 speed only */ + hw->speed_downgraded = FALSE; } return E1000_SUCCESS; @@ -6317,7 +6969,9 @@ e1000_config_dsp_after_link_change(struct e1000_hw *hw, if(speed == SPEED_1000) { - e1000_get_cable_length(hw, &min_length, &max_length); + ret_val = e1000_get_cable_length(hw, &min_length, &max_length); + if (ret_val) + return ret_val; if((hw->dsp_config_state == e1000_dsp_config_enabled) && min_length >= e1000_igp_cable_length_50) { @@ -6525,20 +7179,27 @@ static int32_t e1000_set_d3_lplu_state(struct e1000_hw *hw, boolean_t active) { + uint32_t phy_ctrl = 0; int32_t ret_val; uint16_t phy_data; DEBUGFUNC("e1000_set_d3_lplu_state"); - if(hw->phy_type != e1000_phy_igp && hw->phy_type != e1000_phy_igp_2) + if (hw->phy_type != e1000_phy_igp && hw->phy_type != e1000_phy_igp_2 + && hw->phy_type != e1000_phy_igp_3) return E1000_SUCCESS; /* During driver activity LPLU should not be used or it will attain link * from the lowest speeds starting from 10Mbps. The capability is used for * Dx transitions and states */ - if(hw->mac_type == e1000_82541_rev_2 || hw->mac_type == e1000_82547_rev_2) { + if (hw->mac_type == e1000_82541_rev_2 || hw->mac_type == e1000_82547_rev_2) { ret_val = e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO, &phy_data); - if(ret_val) + if (ret_val) return ret_val; + } else if (hw->mac_type == e1000_ich8lan) { + /* MAC writes into PHY register based on the state transition + * and start auto-negotiation. SW driver can overwrite the settings + * in CSR PHY power control E1000_PHY_CTRL register. */ + phy_ctrl = E1000_READ_REG(hw, PHY_CTRL); } else { ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data); if(ret_val) @@ -6553,11 +7214,16 @@ e1000_set_d3_lplu_state(struct e1000_hw *hw, if(ret_val) return ret_val; } else { + if (hw->mac_type == e1000_ich8lan) { + phy_ctrl &= ~E1000_PHY_CTRL_NOND0A_LPLU; + E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl); + } else { phy_data &= ~IGP02E1000_PM_D3_LPLU; ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, phy_data); if (ret_val) return ret_val; + } } /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during @@ -6593,17 +7259,22 @@ e1000_set_d3_lplu_state(struct e1000_hw *hw, (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_100_ALL)) { if(hw->mac_type == e1000_82541_rev_2 || - hw->mac_type == e1000_82547_rev_2) { + hw->mac_type == e1000_82547_rev_2) { phy_data |= IGP01E1000_GMII_FLEX_SPD; ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, phy_data); if(ret_val) return ret_val; } else { + if (hw->mac_type == e1000_ich8lan) { + phy_ctrl |= E1000_PHY_CTRL_NOND0A_LPLU; + E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl); + } else { phy_data |= IGP02E1000_PM_D3_LPLU; ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, phy_data); if (ret_val) return ret_val; + } } /* When LPLU is enabled we should disable SmartSpeed */ @@ -6638,6 +7309,7 @@ static int32_t e1000_set_d0_lplu_state(struct e1000_hw *hw, boolean_t active) { + uint32_t phy_ctrl = 0; int32_t ret_val; uint16_t phy_data; DEBUGFUNC("e1000_set_d0_lplu_state"); @@ -6645,15 +7317,24 @@ e1000_set_d0_lplu_state(struct e1000_hw *hw, if(hw->mac_type <= e1000_82547_rev_2) return E1000_SUCCESS; + if (hw->mac_type == e1000_ich8lan) { + phy_ctrl = E1000_READ_REG(hw, PHY_CTRL); + } else { ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data); if(ret_val) return ret_val; + } if (!active) { + if (hw->mac_type == e1000_ich8lan) { + phy_ctrl &= ~E1000_PHY_CTRL_D0A_LPLU; + E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl); + } else { phy_data &= ~IGP02E1000_PM_D0_LPLU; ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, phy_data); if (ret_val) return ret_val; + } /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during * Dx states where the power conservation is most important. During @@ -6686,10 +7367,15 @@ e1000_set_d0_lplu_state(struct e1000_hw *hw, } else { + if (hw->mac_type == e1000_ich8lan) { + phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU; + E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl); + } else { phy_data |= IGP02E1000_PM_D0_LPLU; ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, phy_data); if (ret_val) return ret_val; + } /* When LPLU is enabled we should disable SmartSpeed */ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, &phy_data); @@ -6928,8 +7614,10 @@ e1000_mng_write_cmd_header(struct e1000_hw * hw, length >>= 2; /* The device driver writes the relevant command block into the ram area. */ - for (i = 0; i < length; i++) + for (i = 0; i < length; i++) { E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, i, *((uint32_t *) hdr + i)); + E1000_WRITE_FLUSH(hw); + } return E1000_SUCCESS; } @@ -6961,15 +7649,18 @@ e1000_mng_write_commit( * returns - TRUE when the mode is IAMT or FALSE. ****************************************************************************/ boolean_t -e1000_check_mng_mode( - struct e1000_hw *hw) +e1000_check_mng_mode(struct e1000_hw *hw) { uint32_t fwsm; fwsm = E1000_READ_REG(hw, FWSM); - if((fwsm & E1000_FWSM_MODE_MASK) == - (E1000_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT)) + if (hw->mac_type == e1000_ich8lan) { + if ((fwsm & E1000_FWSM_MODE_MASK) == + (E1000_MNG_ICH_IAMT_MODE << E1000_FWSM_MODE_SHIFT)) + return TRUE; + } else if ((fwsm & E1000_FWSM_MODE_MASK) == + (E1000_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT)) return TRUE; return FALSE; @@ -7209,7 +7900,6 @@ e1000_set_pci_express_master_disable(struct e1000_hw *hw) E1000_WRITE_REG(hw, CTRL, ctrl); } -#if 0 /*************************************************************************** * * Enables PCI-Express master access. @@ -7233,7 +7923,6 @@ e1000_enable_pciex_master(struct e1000_hw *hw) ctrl &= ~E1000_CTRL_GIO_MASTER_DISABLE; E1000_WRITE_REG(hw, CTRL, ctrl); } -#endif /* 0 */ /******************************************************************************* * @@ -7299,8 +7988,10 @@ e1000_get_auto_rd_done(struct e1000_hw *hw) case e1000_82572: case e1000_82573: case e1000_80003es2lan: - while(timeout) { - if (E1000_READ_REG(hw, EECD) & E1000_EECD_AUTO_RD) break; + case e1000_ich8lan: + while (timeout) { + if (E1000_READ_REG(hw, EECD) & E1000_EECD_AUTO_RD) + break; else msec_delay(1); timeout--; } @@ -7340,7 +8031,7 @@ e1000_get_phy_cfg_done(struct e1000_hw *hw) switch (hw->mac_type) { default: - msec_delay(10); + msec_delay_irq(10); break; case e1000_80003es2lan: /* Separate *_CFG_DONE_* bit for each port */ @@ -7523,6 +8214,13 @@ int32_t e1000_check_phy_reset_block(struct e1000_hw *hw) { uint32_t manc = 0; + uint32_t fwsm = 0; + + if (hw->mac_type == e1000_ich8lan) { + fwsm = E1000_READ_REG(hw, FWSM); + return (fwsm & E1000_FWSM_RSPCIPHY) ? E1000_SUCCESS + : E1000_BLK_PHY_RESET; + } if (hw->mac_type > e1000_82547_rev_2) manc = E1000_READ_REG(hw, MANC); @@ -7549,6 +8247,8 @@ e1000_arc_subsystem_valid(struct e1000_hw *hw) if((fwsm & E1000_FWSM_MODE_MASK) != 0) return TRUE; break; + case e1000_ich8lan: + return TRUE; default: break; } @@ -7556,4 +8256,846 @@ e1000_arc_subsystem_valid(struct e1000_hw *hw) } +/****************************************************************************** + * Configure PCI-Ex no-snoop + * + * hw - Struct containing variables accessed by shared code. + * no_snoop - Bitmap of no-snoop events. + * + * returns: E1000_SUCCESS + * + *****************************************************************************/ +int32_t +e1000_set_pci_ex_no_snoop(struct e1000_hw *hw, uint32_t no_snoop) +{ + uint32_t gcr_reg = 0; + + DEBUGFUNC("e1000_set_pci_ex_no_snoop"); + + if (hw->bus_type == e1000_bus_type_unknown) + e1000_get_bus_info(hw); + + if (hw->bus_type != e1000_bus_type_pci_express) + return E1000_SUCCESS; + + if (no_snoop) { + gcr_reg = E1000_READ_REG(hw, GCR); + gcr_reg &= ~(PCI_EX_NO_SNOOP_ALL); + gcr_reg |= no_snoop; + E1000_WRITE_REG(hw, GCR, gcr_reg); + } + if (hw->mac_type == e1000_ich8lan) { + uint32_t ctrl_ext; + + E1000_WRITE_REG(hw, GCR, PCI_EX_82566_SNOOP_ALL); + + ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); + ctrl_ext |= E1000_CTRL_EXT_RO_DIS; + E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); + } + + return E1000_SUCCESS; +} + +/*************************************************************************** + * + * Get software semaphore FLAG bit (SWFLAG). + * SWFLAG is used to synchronize the access to all shared resource between + * SW, FW and HW. + * + * hw: Struct containing variables accessed by shared code + * + ***************************************************************************/ +int32_t +e1000_get_software_flag(struct e1000_hw *hw) +{ + int32_t timeout = PHY_CFG_TIMEOUT; + uint32_t extcnf_ctrl; + + DEBUGFUNC("e1000_get_software_flag"); + + if (hw->mac_type == e1000_ich8lan) { + while (timeout) { + extcnf_ctrl = E1000_READ_REG(hw, EXTCNF_CTRL); + extcnf_ctrl |= E1000_EXTCNF_CTRL_SWFLAG; + E1000_WRITE_REG(hw, EXTCNF_CTRL, extcnf_ctrl); + + extcnf_ctrl = E1000_READ_REG(hw, EXTCNF_CTRL); + if (extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG) + break; + msec_delay_irq(1); + timeout--; + } + + if (!timeout) { + DEBUGOUT("FW or HW locks the resource too long.\n"); + return -E1000_ERR_CONFIG; + } + } + + return E1000_SUCCESS; +} + +/*************************************************************************** + * + * Release software semaphore FLAG bit (SWFLAG). + * SWFLAG is used to synchronize the access to all shared resource between + * SW, FW and HW. + * + * hw: Struct containing variables accessed by shared code + * + ***************************************************************************/ +void +e1000_release_software_flag(struct e1000_hw *hw) +{ + uint32_t extcnf_ctrl; + + DEBUGFUNC("e1000_release_software_flag"); + + if (hw->mac_type == e1000_ich8lan) { + extcnf_ctrl= E1000_READ_REG(hw, EXTCNF_CTRL); + extcnf_ctrl &= ~E1000_EXTCNF_CTRL_SWFLAG; + E1000_WRITE_REG(hw, EXTCNF_CTRL, extcnf_ctrl); + } + + return; +} + +/*************************************************************************** + * + * Disable dynamic power down mode in ife PHY. + * It can be used to workaround band-gap problem. + * + * hw: Struct containing variables accessed by shared code + * + ***************************************************************************/ +int32_t +e1000_ife_disable_dynamic_power_down(struct e1000_hw *hw) +{ + uint16_t phy_data; + int32_t ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_ife_disable_dynamic_power_down"); + + if (hw->phy_type == e1000_phy_ife) { + ret_val = e1000_read_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL, &phy_data); + if (ret_val) + return ret_val; + + phy_data |= IFE_PSC_DISABLE_DYNAMIC_POWER_DOWN; + ret_val = e1000_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL, phy_data); + } + + return ret_val; +} + +/*************************************************************************** + * + * Enable dynamic power down mode in ife PHY. + * It can be used to workaround band-gap problem. + * + * hw: Struct containing variables accessed by shared code + * + ***************************************************************************/ +int32_t +e1000_ife_enable_dynamic_power_down(struct e1000_hw *hw) +{ + uint16_t phy_data; + int32_t ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_ife_enable_dynamic_power_down"); + + if (hw->phy_type == e1000_phy_ife) { + ret_val = e1000_read_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL, &phy_data); + if (ret_val) + return ret_val; + + phy_data &= ~IFE_PSC_DISABLE_DYNAMIC_POWER_DOWN; + ret_val = e1000_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL, phy_data); + } + + return ret_val; +} + +/****************************************************************************** + * Reads a 16 bit word or words from the EEPROM using the ICH8's flash access + * register. + * + * hw - Struct containing variables accessed by shared code + * offset - offset of word in the EEPROM to read + * data - word read from the EEPROM + * words - number of words to read + *****************************************************************************/ +int32_t +e1000_read_eeprom_ich8(struct e1000_hw *hw, uint16_t offset, uint16_t words, + uint16_t *data) +{ + int32_t error = E1000_SUCCESS; + uint32_t flash_bank = 0; + uint32_t act_offset = 0; + uint32_t bank_offset = 0; + uint16_t word = 0; + uint16_t i = 0; + + /* We need to know which is the valid flash bank. In the event + * that we didn't allocate eeprom_shadow_ram, we may not be + * managing flash_bank. So it cannot be trusted and needs + * to be updated with each read. + */ + /* Value of bit 22 corresponds to the flash bank we're on. */ + flash_bank = (E1000_READ_REG(hw, EECD) & E1000_EECD_SEC1VAL) ? 1 : 0; + + /* Adjust offset appropriately if we're on bank 1 - adjust for word size */ + bank_offset = flash_bank * (hw->flash_bank_size * 2); + + error = e1000_get_software_flag(hw); + if (error != E1000_SUCCESS) + return error; + + for (i = 0; i < words; i++) { + if (hw->eeprom_shadow_ram != NULL && + hw->eeprom_shadow_ram[offset+i].modified == TRUE) { + data[i] = hw->eeprom_shadow_ram[offset+i].eeprom_word; + } else { + /* The NVM part needs a byte offset, hence * 2 */ + act_offset = bank_offset + ((offset + i) * 2); + error = e1000_read_ich8_word(hw, act_offset, &word); + if (error != E1000_SUCCESS) + break; + data[i] = word; + } + } + + e1000_release_software_flag(hw); + + return error; +} + +/****************************************************************************** + * Writes a 16 bit word or words to the EEPROM using the ICH8's flash access + * register. Actually, writes are written to the shadow ram cache in the hw + * structure hw->e1000_shadow_ram. e1000_commit_shadow_ram flushes this to + * the NVM, which occurs when the NVM checksum is updated. + * + * hw - Struct containing variables accessed by shared code + * offset - offset of word in the EEPROM to write + * words - number of words to write + * data - words to write to the EEPROM + *****************************************************************************/ +int32_t +e1000_write_eeprom_ich8(struct e1000_hw *hw, uint16_t offset, uint16_t words, + uint16_t *data) +{ + uint32_t i = 0; + int32_t error = E1000_SUCCESS; + + error = e1000_get_software_flag(hw); + if (error != E1000_SUCCESS) + return error; + + /* A driver can write to the NVM only if it has eeprom_shadow_ram + * allocated. Subsequent reads to the modified words are read from + * this cached structure as well. Writes will only go into this + * cached structure unless it's followed by a call to + * e1000_update_eeprom_checksum() where it will commit the changes + * and clear the "modified" field. + */ + if (hw->eeprom_shadow_ram != NULL) { + for (i = 0; i < words; i++) { + if ((offset + i) < E1000_SHADOW_RAM_WORDS) { + hw->eeprom_shadow_ram[offset+i].modified = TRUE; + hw->eeprom_shadow_ram[offset+i].eeprom_word = data[i]; + } else { + error = -E1000_ERR_EEPROM; + break; + } + } + } else { + /* Drivers have the option to not allocate eeprom_shadow_ram as long + * as they don't perform any NVM writes. An attempt in doing so + * will result in this error. + */ + error = -E1000_ERR_EEPROM; + } + + e1000_release_software_flag(hw); + + return error; +} + +/****************************************************************************** + * This function does initial flash setup so that a new read/write/erase cycle + * can be started. + * + * hw - The pointer to the hw structure + ****************************************************************************/ +int32_t +e1000_ich8_cycle_init(struct e1000_hw *hw) +{ + union ich8_hws_flash_status hsfsts; + int32_t error = E1000_ERR_EEPROM; + int32_t i = 0; + + DEBUGFUNC("e1000_ich8_cycle_init"); + + hsfsts.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFSTS); + + /* May be check the Flash Des Valid bit in Hw status */ + if (hsfsts.hsf_status.fldesvalid == 0) { + DEBUGOUT("Flash descriptor invalid. SW Sequencing must be used."); + return error; + } + + /* Clear FCERR in Hw status by writing 1 */ + /* Clear DAEL in Hw status by writing a 1 */ + hsfsts.hsf_status.flcerr = 1; + hsfsts.hsf_status.dael = 1; + + E1000_WRITE_ICH8_REG16(hw, ICH8_FLASH_HSFSTS, hsfsts.regval); + + /* Either we should have a hardware SPI cycle in progress bit to check + * against, in order to start a new cycle or FDONE bit should be changed + * in the hardware so that it is 1 after harware reset, which can then be + * used as an indication whether a cycle is in progress or has been + * completed .. we should also have some software semaphore mechanism to + * guard FDONE or the cycle in progress bit so that two threads access to + * those bits can be sequentiallized or a way so that 2 threads dont + * start the cycle at the same time */ + + if (hsfsts.hsf_status.flcinprog == 0) { + /* There is no cycle running at present, so we can start a cycle */ + /* Begin by setting Flash Cycle Done. */ + hsfsts.hsf_status.flcdone = 1; + E1000_WRITE_ICH8_REG16(hw, ICH8_FLASH_HSFSTS, hsfsts.regval); + error = E1000_SUCCESS; + } else { + /* otherwise poll for sometime so the current cycle has a chance + * to end before giving up. */ + for (i = 0; i < ICH8_FLASH_COMMAND_TIMEOUT; i++) { + hsfsts.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFSTS); + if (hsfsts.hsf_status.flcinprog == 0) { + error = E1000_SUCCESS; + break; + } + udelay(1); + } + if (error == E1000_SUCCESS) { + /* Successful in waiting for previous cycle to timeout, + * now set the Flash Cycle Done. */ + hsfsts.hsf_status.flcdone = 1; + E1000_WRITE_ICH8_REG16(hw, ICH8_FLASH_HSFSTS, hsfsts.regval); + } else { + DEBUGOUT("Flash controller busy, cannot get access"); + } + } + return error; +} + +/****************************************************************************** + * This function starts a flash cycle and waits for its completion + * + * hw - The pointer to the hw structure + ****************************************************************************/ +int32_t +e1000_ich8_flash_cycle(struct e1000_hw *hw, uint32_t timeout) +{ + union ich8_hws_flash_ctrl hsflctl; + union ich8_hws_flash_status hsfsts; + int32_t error = E1000_ERR_EEPROM; + uint32_t i = 0; + + /* Start a cycle by writing 1 in Flash Cycle Go in Hw Flash Control */ + hsflctl.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFCTL); + hsflctl.hsf_ctrl.flcgo = 1; + E1000_WRITE_ICH8_REG16(hw, ICH8_FLASH_HSFCTL, hsflctl.regval); + + /* wait till FDONE bit is set to 1 */ + do { + hsfsts.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFSTS); + if (hsfsts.hsf_status.flcdone == 1) + break; + udelay(1); + i++; + } while (i < timeout); + if (hsfsts.hsf_status.flcdone == 1 && hsfsts.hsf_status.flcerr == 0) { + error = E1000_SUCCESS; + } + return error; +} + +/****************************************************************************** + * Reads a byte or word from the NVM using the ICH8 flash access registers. + * + * hw - The pointer to the hw structure + * index - The index of the byte or word to read. + * size - Size of data to read, 1=byte 2=word + * data - Pointer to the word to store the value read. + *****************************************************************************/ +int32_t +e1000_read_ich8_data(struct e1000_hw *hw, uint32_t index, + uint32_t size, uint16_t* data) +{ + union ich8_hws_flash_status hsfsts; + union ich8_hws_flash_ctrl hsflctl; + uint32_t flash_linear_address; + uint32_t flash_data = 0; + int32_t error = -E1000_ERR_EEPROM; + int32_t count = 0; + + DEBUGFUNC("e1000_read_ich8_data"); + + if (size < 1 || size > 2 || data == 0x0 || + index > ICH8_FLASH_LINEAR_ADDR_MASK) + return error; + + flash_linear_address = (ICH8_FLASH_LINEAR_ADDR_MASK & index) + + hw->flash_base_addr; + + do { + udelay(1); + /* Steps */ + error = e1000_ich8_cycle_init(hw); + if (error != E1000_SUCCESS) + break; + + hsflctl.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFCTL); + /* 0b/1b corresponds to 1 or 2 byte size, respectively. */ + hsflctl.hsf_ctrl.fldbcount = size - 1; + hsflctl.hsf_ctrl.flcycle = ICH8_CYCLE_READ; + E1000_WRITE_ICH8_REG16(hw, ICH8_FLASH_HSFCTL, hsflctl.regval); + + /* Write the last 24 bits of index into Flash Linear address field in + * Flash Address */ + /* TODO: TBD maybe check the index against the size of flash */ + + E1000_WRITE_ICH8_REG(hw, ICH8_FLASH_FADDR, flash_linear_address); + + error = e1000_ich8_flash_cycle(hw, ICH8_FLASH_COMMAND_TIMEOUT); + + /* Check if FCERR is set to 1, if set to 1, clear it and try the whole + * sequence a few more times, else read in (shift in) the Flash Data0, + * the order is least significant byte first msb to lsb */ + if (error == E1000_SUCCESS) { + flash_data = E1000_READ_ICH8_REG(hw, ICH8_FLASH_FDATA0); + if (size == 1) { + *data = (uint8_t)(flash_data & 0x000000FF); + } else if (size == 2) { + *data = (uint16_t)(flash_data & 0x0000FFFF); + } + break; + } else { + /* If we've gotten here, then things are probably completely hosed, + * but if the error condition is detected, it won't hurt to give + * it another try...ICH8_FLASH_CYCLE_REPEAT_COUNT times. + */ + hsfsts.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFSTS); + if (hsfsts.hsf_status.flcerr == 1) { + /* Repeat for some time before giving up. */ + continue; + } else if (hsfsts.hsf_status.flcdone == 0) { + DEBUGOUT("Timeout error - flash cycle did not complete."); + break; + } + } + } while (count++ < ICH8_FLASH_CYCLE_REPEAT_COUNT); + + return error; +} + +/****************************************************************************** + * Writes One /two bytes to the NVM using the ICH8 flash access registers. + * + * hw - The pointer to the hw structure + * index - The index of the byte/word to read. + * size - Size of data to read, 1=byte 2=word + * data - The byte(s) to write to the NVM. + *****************************************************************************/ +int32_t +e1000_write_ich8_data(struct e1000_hw *hw, uint32_t index, uint32_t size, + uint16_t data) +{ + union ich8_hws_flash_status hsfsts; + union ich8_hws_flash_ctrl hsflctl; + uint32_t flash_linear_address; + uint32_t flash_data = 0; + int32_t error = -E1000_ERR_EEPROM; + int32_t count = 0; + + DEBUGFUNC("e1000_write_ich8_data"); + + if (size < 1 || size > 2 || data > size * 0xff || + index > ICH8_FLASH_LINEAR_ADDR_MASK) + return error; + + flash_linear_address = (ICH8_FLASH_LINEAR_ADDR_MASK & index) + + hw->flash_base_addr; + + do { + udelay(1); + /* Steps */ + error = e1000_ich8_cycle_init(hw); + if (error != E1000_SUCCESS) + break; + + hsflctl.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFCTL); + /* 0b/1b corresponds to 1 or 2 byte size, respectively. */ + hsflctl.hsf_ctrl.fldbcount = size -1; + hsflctl.hsf_ctrl.flcycle = ICH8_CYCLE_WRITE; + E1000_WRITE_ICH8_REG16(hw, ICH8_FLASH_HSFCTL, hsflctl.regval); + + /* Write the last 24 bits of index into Flash Linear address field in + * Flash Address */ + E1000_WRITE_ICH8_REG(hw, ICH8_FLASH_FADDR, flash_linear_address); + + if (size == 1) + flash_data = (uint32_t)data & 0x00FF; + else + flash_data = (uint32_t)data; + + E1000_WRITE_ICH8_REG(hw, ICH8_FLASH_FDATA0, flash_data); + + /* check if FCERR is set to 1 , if set to 1, clear it and try the whole + * sequence a few more times else done */ + error = e1000_ich8_flash_cycle(hw, ICH8_FLASH_COMMAND_TIMEOUT); + if (error == E1000_SUCCESS) { + break; + } else { + /* If we're here, then things are most likely completely hosed, + * but if the error condition is detected, it won't hurt to give + * it another try...ICH8_FLASH_CYCLE_REPEAT_COUNT times. + */ + hsfsts.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFSTS); + if (hsfsts.hsf_status.flcerr == 1) { + /* Repeat for some time before giving up. */ + continue; + } else if (hsfsts.hsf_status.flcdone == 0) { + DEBUGOUT("Timeout error - flash cycle did not complete."); + break; + } + } + } while (count++ < ICH8_FLASH_CYCLE_REPEAT_COUNT); + + return error; +} + +/****************************************************************************** + * Reads a single byte from the NVM using the ICH8 flash access registers. + * + * hw - pointer to e1000_hw structure + * index - The index of the byte to read. + * data - Pointer to a byte to store the value read. + *****************************************************************************/ +int32_t +e1000_read_ich8_byte(struct e1000_hw *hw, uint32_t index, uint8_t* data) +{ + int32_t status = E1000_SUCCESS; + uint16_t word = 0; + + status = e1000_read_ich8_data(hw, index, 1, &word); + if (status == E1000_SUCCESS) { + *data = (uint8_t)word; + } + + return status; +} + +/****************************************************************************** + * Writes a single byte to the NVM using the ICH8 flash access registers. + * Performs verification by reading back the value and then going through + * a retry algorithm before giving up. + * + * hw - pointer to e1000_hw structure + * index - The index of the byte to write. + * byte - The byte to write to the NVM. + *****************************************************************************/ +int32_t +e1000_verify_write_ich8_byte(struct e1000_hw *hw, uint32_t index, uint8_t byte) +{ + int32_t error = E1000_SUCCESS; + int32_t program_retries; + uint8_t temp_byte; + + e1000_write_ich8_byte(hw, index, byte); + udelay(100); + + for (program_retries = 0; program_retries < 100; program_retries++) { + e1000_read_ich8_byte(hw, index, &temp_byte); + if (temp_byte == byte) + break; + udelay(10); + e1000_write_ich8_byte(hw, index, byte); + udelay(100); + } + if (program_retries == 100) + error = E1000_ERR_EEPROM; + + return error; +} + +/****************************************************************************** + * Writes a single byte to the NVM using the ICH8 flash access registers. + * + * hw - pointer to e1000_hw structure + * index - The index of the byte to read. + * data - The byte to write to the NVM. + *****************************************************************************/ +int32_t +e1000_write_ich8_byte(struct e1000_hw *hw, uint32_t index, uint8_t data) +{ + int32_t status = E1000_SUCCESS; + uint16_t word = (uint16_t)data; + + status = e1000_write_ich8_data(hw, index, 1, word); + + return status; +} + +/****************************************************************************** + * Reads a word from the NVM using the ICH8 flash access registers. + * + * hw - pointer to e1000_hw structure + * index - The starting byte index of the word to read. + * data - Pointer to a word to store the value read. + *****************************************************************************/ +int32_t +e1000_read_ich8_word(struct e1000_hw *hw, uint32_t index, uint16_t *data) +{ + int32_t status = E1000_SUCCESS; + status = e1000_read_ich8_data(hw, index, 2, data); + return status; +} + +/****************************************************************************** + * Writes a word to the NVM using the ICH8 flash access registers. + * + * hw - pointer to e1000_hw structure + * index - The starting byte index of the word to read. + * data - The word to write to the NVM. + *****************************************************************************/ +int32_t +e1000_write_ich8_word(struct e1000_hw *hw, uint32_t index, uint16_t data) +{ + int32_t status = E1000_SUCCESS; + status = e1000_write_ich8_data(hw, index, 2, data); + return status; +} + +/****************************************************************************** + * Erases the bank specified. Each bank is a 4k block. Segments are 0 based. + * segment N is 4096 * N + flash_reg_addr. + * + * hw - pointer to e1000_hw structure + * segment - 0 for first segment, 1 for second segment, etc. + *****************************************************************************/ +int32_t +e1000_erase_ich8_4k_segment(struct e1000_hw *hw, uint32_t segment) +{ + union ich8_hws_flash_status hsfsts; + union ich8_hws_flash_ctrl hsflctl; + uint32_t flash_linear_address; + int32_t count = 0; + int32_t error = E1000_ERR_EEPROM; + int32_t iteration, seg_size; + int32_t sector_size; + int32_t j = 0; + int32_t error_flag = 0; + + hsfsts.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFSTS); + + /* Determine HW Sector size: Read BERASE bits of Hw flash Status register */ + /* 00: The Hw sector is 256 bytes, hence we need to erase 16 + * consecutive sectors. The start index for the nth Hw sector can be + * calculated as = segment * 4096 + n * 256 + * 01: The Hw sector is 4K bytes, hence we need to erase 1 sector. + * The start index for the nth Hw sector can be calculated + * as = segment * 4096 + * 10: Error condition + * 11: The Hw sector size is much bigger than the size asked to + * erase...error condition */ + if (hsfsts.hsf_status.berasesz == 0x0) { + /* Hw sector size 256 */ + sector_size = seg_size = ICH8_FLASH_SEG_SIZE_256; + iteration = ICH8_FLASH_SECTOR_SIZE / ICH8_FLASH_SEG_SIZE_256; + } else if (hsfsts.hsf_status.berasesz == 0x1) { + sector_size = seg_size = ICH8_FLASH_SEG_SIZE_4K; + iteration = 1; + } else if (hsfsts.hsf_status.berasesz == 0x3) { + sector_size = seg_size = ICH8_FLASH_SEG_SIZE_64K; + iteration = 1; + } else { + return error; + } + + for (j = 0; j < iteration ; j++) { + do { + count++; + /* Steps */ + error = e1000_ich8_cycle_init(hw); + if (error != E1000_SUCCESS) { + error_flag = 1; + break; + } + + /* Write a value 11 (block Erase) in Flash Cycle field in Hw flash + * Control */ + hsflctl.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFCTL); + hsflctl.hsf_ctrl.flcycle = ICH8_CYCLE_ERASE; + E1000_WRITE_ICH8_REG16(hw, ICH8_FLASH_HSFCTL, hsflctl.regval); + + /* Write the last 24 bits of an index within the block into Flash + * Linear address field in Flash Address. This probably needs to + * be calculated here based off the on-chip segment size and the + * software segment size assumed (4K) */ + /* TBD */ + flash_linear_address = segment * sector_size + j * seg_size; + flash_linear_address &= ICH8_FLASH_LINEAR_ADDR_MASK; + flash_linear_address += hw->flash_base_addr; + + E1000_WRITE_ICH8_REG(hw, ICH8_FLASH_FADDR, flash_linear_address); + + error = e1000_ich8_flash_cycle(hw, 1000000); + /* Check if FCERR is set to 1. If 1, clear it and try the whole + * sequence a few more times else Done */ + if (error == E1000_SUCCESS) { + break; + } else { + hsfsts.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFSTS); + if (hsfsts.hsf_status.flcerr == 1) { + /* repeat for some time before giving up */ + continue; + } else if (hsfsts.hsf_status.flcdone == 0) { + error_flag = 1; + break; + } + } + } while ((count < ICH8_FLASH_CYCLE_REPEAT_COUNT) && !error_flag); + if (error_flag == 1) + break; + } + if (error_flag != 1) + error = E1000_SUCCESS; + return error; +} + +/****************************************************************************** + * + * Reverse duplex setting without breaking the link. + * + * hw: Struct containing variables accessed by shared code + * + *****************************************************************************/ +int32_t +e1000_duplex_reversal(struct e1000_hw *hw) +{ + int32_t ret_val; + uint16_t phy_data; + + if (hw->phy_type != e1000_phy_igp_3) + return E1000_SUCCESS; + + ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data); + if (ret_val) + return ret_val; + + phy_data ^= MII_CR_FULL_DUPLEX; + + ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data); + if (ret_val) + return ret_val; + + ret_val = e1000_read_phy_reg(hw, IGP3E1000_PHY_MISC_CTRL, &phy_data); + if (ret_val) + return ret_val; + + phy_data |= IGP3_PHY_MISC_DUPLEX_MANUAL_SET; + ret_val = e1000_write_phy_reg(hw, IGP3E1000_PHY_MISC_CTRL, phy_data); + + return ret_val; +} + +int32_t +e1000_init_lcd_from_nvm_config_region(struct e1000_hw *hw, + uint32_t cnf_base_addr, uint32_t cnf_size) +{ + uint32_t ret_val = E1000_SUCCESS; + uint16_t word_addr, reg_data, reg_addr; + uint16_t i; + + /* cnf_base_addr is in DWORD */ + word_addr = (uint16_t)(cnf_base_addr << 1); + + /* cnf_size is returned in size of dwords */ + for (i = 0; i < cnf_size; i++) { + ret_val = e1000_read_eeprom(hw, (word_addr + i*2), 1, ®_data); + if (ret_val) + return ret_val; + + ret_val = e1000_read_eeprom(hw, (word_addr + i*2 + 1), 1, ®_addr); + if (ret_val) + return ret_val; + + ret_val = e1000_get_software_flag(hw); + if (ret_val != E1000_SUCCESS) + return ret_val; + + ret_val = e1000_write_phy_reg_ex(hw, (uint32_t)reg_addr, reg_data); + + e1000_release_software_flag(hw); + } + + return ret_val; +} + + +int32_t +e1000_init_lcd_from_nvm(struct e1000_hw *hw) +{ + uint32_t reg_data, cnf_base_addr, cnf_size, ret_val, loop; + + if (hw->phy_type != e1000_phy_igp_3) + return E1000_SUCCESS; + + /* Check if SW needs configure the PHY */ + reg_data = E1000_READ_REG(hw, FEXTNVM); + if (!(reg_data & FEXTNVM_SW_CONFIG)) + return E1000_SUCCESS; + + /* Wait for basic configuration completes before proceeding*/ + loop = 0; + do { + reg_data = E1000_READ_REG(hw, STATUS) & E1000_STATUS_LAN_INIT_DONE; + udelay(100); + loop++; + } while ((!reg_data) && (loop < 50)); + + /* Clear the Init Done bit for the next init event */ + reg_data = E1000_READ_REG(hw, STATUS); + reg_data &= ~E1000_STATUS_LAN_INIT_DONE; + E1000_WRITE_REG(hw, STATUS, reg_data); + + /* Make sure HW does not configure LCD from PHY extended configuration + before SW configuration */ + reg_data = E1000_READ_REG(hw, EXTCNF_CTRL); + if ((reg_data & E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE) == 0x0000) { + reg_data = E1000_READ_REG(hw, EXTCNF_SIZE); + cnf_size = reg_data & E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH; + cnf_size >>= 16; + if (cnf_size) { + reg_data = E1000_READ_REG(hw, EXTCNF_CTRL); + cnf_base_addr = reg_data & E1000_EXTCNF_CTRL_EXT_CNF_POINTER; + /* cnf_base_addr is in DWORD */ + cnf_base_addr >>= 16; + + /* Configure LCD from extended configuration region. */ + ret_val = e1000_init_lcd_from_nvm_config_region(hw, cnf_base_addr, + cnf_size); + if (ret_val) + return ret_val; + } + } + + return E1000_SUCCESS; +} + + diff --git a/drivers/net/e1000/e1000_hw.h b/drivers/net/e1000/e1000_hw.h index 467c9ed944f..f9341e3276b 100644 --- a/drivers/net/e1000/e1000_hw.h +++ b/drivers/net/e1000/e1000_hw.h @@ -62,6 +62,7 @@ typedef enum { e1000_82572, e1000_82573, e1000_80003es2lan, + e1000_ich8lan, e1000_num_macs } e1000_mac_type; @@ -70,6 +71,7 @@ typedef enum { e1000_eeprom_spi, e1000_eeprom_microwire, e1000_eeprom_flash, + e1000_eeprom_ich8, e1000_eeprom_none, /* No NVM support */ e1000_num_eeprom_types } e1000_eeprom_type; @@ -98,6 +100,11 @@ typedef enum { e1000_fc_default = 0xFF } e1000_fc_type; +struct e1000_shadow_ram { + uint16_t eeprom_word; + boolean_t modified; +}; + /* PCI bus types */ typedef enum { e1000_bus_type_unknown = 0, @@ -218,6 +225,8 @@ typedef enum { e1000_phy_igp, e1000_phy_igp_2, e1000_phy_gg82563, + e1000_phy_igp_3, + e1000_phy_ife, e1000_phy_undefined = 0xFF } e1000_phy_type; @@ -313,6 +322,10 @@ int32_t e1000_read_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t *phy int32_t e1000_write_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t data); int32_t e1000_phy_hw_reset(struct e1000_hw *hw); int32_t e1000_phy_reset(struct e1000_hw *hw); +void e1000_phy_powerdown_workaround(struct e1000_hw *hw); +int32_t e1000_kumeran_lock_loss_workaround(struct e1000_hw *hw); +int32_t e1000_init_lcd_from_nvm_config_region(struct e1000_hw *hw, uint32_t cnf_base_addr, uint32_t cnf_size); +int32_t e1000_init_lcd_from_nvm(struct e1000_hw *hw); int32_t e1000_phy_get_info(struct e1000_hw *hw, struct e1000_phy_info *phy_info); int32_t e1000_validate_mdi_setting(struct e1000_hw *hw); int32_t e1000_read_kmrn_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t *data); @@ -331,6 +344,7 @@ uint32_t e1000_enable_mng_pass_thru(struct e1000_hw *hw); #define E1000_MNG_DHCP_COOKIE_OFFSET 0x6F0 /* Cookie offset */ #define E1000_MNG_DHCP_COOKIE_LENGTH 0x10 /* Cookie length */ #define E1000_MNG_IAMT_MODE 0x3 +#define E1000_MNG_ICH_IAMT_MODE 0x2 #define E1000_IAMT_SIGNATURE 0x544D4149 /* Intel(R) Active Management Technology signature */ #define E1000_MNG_DHCP_COOKIE_STATUS_PARSING_SUPPORT 0x1 /* DHCP parsing enabled */ @@ -388,6 +402,8 @@ int32_t e1000_read_part_num(struct e1000_hw *hw, uint32_t * part_num); int32_t e1000_read_mac_addr(struct e1000_hw * hw); int32_t e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask); void e1000_swfw_sync_release(struct e1000_hw *hw, uint16_t mask); +void e1000_release_software_flag(struct e1000_hw *hw); +int32_t e1000_get_software_flag(struct e1000_hw *hw); /* Filters (multicast, vlan, receive) */ void e1000_mc_addr_list_update(struct e1000_hw *hw, uint8_t * mc_addr_list, uint32_t mc_addr_count, uint32_t pad, uint32_t rar_used_count); @@ -401,6 +417,7 @@ int32_t e1000_setup_led(struct e1000_hw *hw); int32_t e1000_cleanup_led(struct e1000_hw *hw); int32_t e1000_led_on(struct e1000_hw *hw); int32_t e1000_led_off(struct e1000_hw *hw); +int32_t e1000_blink_led_start(struct e1000_hw *hw); /* Adaptive IFS Functions */ @@ -422,6 +439,29 @@ int32_t e1000_disable_pciex_master(struct e1000_hw *hw); int32_t e1000_get_software_semaphore(struct e1000_hw *hw); void e1000_release_software_semaphore(struct e1000_hw *hw); int32_t e1000_check_phy_reset_block(struct e1000_hw *hw); +int32_t e1000_set_pci_ex_no_snoop(struct e1000_hw *hw, uint32_t no_snoop); + +int32_t e1000_read_ich8_byte(struct e1000_hw *hw, uint32_t index, + uint8_t *data); +int32_t e1000_verify_write_ich8_byte(struct e1000_hw *hw, uint32_t index, + uint8_t byte); +int32_t e1000_write_ich8_byte(struct e1000_hw *hw, uint32_t index, + uint8_t byte); +int32_t e1000_read_ich8_word(struct e1000_hw *hw, uint32_t index, + uint16_t *data); +int32_t e1000_read_ich8_data(struct e1000_hw *hw, uint32_t index, + uint32_t size, uint16_t *data); +int32_t e1000_read_eeprom_ich8(struct e1000_hw *hw, uint16_t offset, + uint16_t words, uint16_t *data); +int32_t e1000_write_eeprom_ich8(struct e1000_hw *hw, uint16_t offset, + uint16_t words, uint16_t *data); +int32_t e1000_erase_ich8_4k_segment(struct e1000_hw *hw, uint32_t segment); + + +#define E1000_READ_REG_IO(a, reg) \ + e1000_read_reg_io((a), E1000_##reg) +#define E1000_WRITE_REG_IO(a, reg, val) \ + e1000_write_reg_io((a), E1000_##reg, val) /* PCI Device IDs */ #define E1000_DEV_ID_82542 0x1000 @@ -446,6 +486,7 @@ int32_t e1000_check_phy_reset_block(struct e1000_hw *hw); #define E1000_DEV_ID_82546EB_QUAD_COPPER 0x101D #define E1000_DEV_ID_82541EI 0x1013 #define E1000_DEV_ID_82541EI_MOBILE 0x1018 +#define E1000_DEV_ID_82541ER_LOM 0x1014 #define E1000_DEV_ID_82541ER 0x1078 #define E1000_DEV_ID_82547GI 0x1075 #define E1000_DEV_ID_82541GI 0x1076 @@ -457,18 +498,28 @@ int32_t e1000_check_phy_reset_block(struct e1000_hw *hw); #define E1000_DEV_ID_82546GB_PCIE 0x108A #define E1000_DEV_ID_82546GB_QUAD_COPPER 0x1099 #define E1000_DEV_ID_82547EI 0x1019 +#define E1000_DEV_ID_82547EI_MOBILE 0x101A #define E1000_DEV_ID_82571EB_COPPER 0x105E #define E1000_DEV_ID_82571EB_FIBER 0x105F #define E1000_DEV_ID_82571EB_SERDES 0x1060 #define E1000_DEV_ID_82572EI_COPPER 0x107D #define E1000_DEV_ID_82572EI_FIBER 0x107E #define E1000_DEV_ID_82572EI_SERDES 0x107F +#define E1000_DEV_ID_82572EI 0x10B9 #define E1000_DEV_ID_82573E 0x108B #define E1000_DEV_ID_82573E_IAMT 0x108C #define E1000_DEV_ID_82573L 0x109A #define E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3 0x10B5 #define E1000_DEV_ID_80003ES2LAN_COPPER_DPT 0x1096 #define E1000_DEV_ID_80003ES2LAN_SERDES_DPT 0x1098 +#define E1000_DEV_ID_80003ES2LAN_COPPER_SPT 0x10BA +#define E1000_DEV_ID_80003ES2LAN_SERDES_SPT 0x10BB + +#define E1000_DEV_ID_ICH8_IGP_M_AMT 0x1049 +#define E1000_DEV_ID_ICH8_IGP_AMT 0x104A +#define E1000_DEV_ID_ICH8_IGP_C 0x104B +#define E1000_DEV_ID_ICH8_IFE 0x104C +#define E1000_DEV_ID_ICH8_IGP_M 0x104D #define NODE_ADDRESS_SIZE 6 @@ -539,6 +590,14 @@ int32_t e1000_check_phy_reset_block(struct e1000_hw *hw); E1000_IMS_RXSEQ | \ E1000_IMS_LSC) +/* Additional interrupts need to be handled for e1000_ich8lan: + DSW = The FW changed the status of the DISSW bit in FWSM + PHYINT = The LAN connected device generates an interrupt + EPRST = Manageability reset event */ +#define IMS_ICH8LAN_ENABLE_MASK (\ + E1000_IMS_DSW | \ + E1000_IMS_PHYINT | \ + E1000_IMS_EPRST) /* Number of high/low register pairs in the RAR. The RAR (Receive Address * Registers) holds the directed and multicast addresses that we monitor. We @@ -546,6 +605,7 @@ int32_t e1000_check_phy_reset_block(struct e1000_hw *hw); * E1000_RAR_ENTRIES - 1 multicast addresses. */ #define E1000_RAR_ENTRIES 15 +#define E1000_RAR_ENTRIES_ICH8LAN 7 #define MIN_NUMBER_OF_DESCRIPTORS 8 #define MAX_NUMBER_OF_DESCRIPTORS 0xFFF8 @@ -767,6 +827,9 @@ struct e1000_data_desc { #define E1000_MC_TBL_SIZE 128 /* Multicast Filter Table (4096 bits) */ #define E1000_VLAN_FILTER_TBL_SIZE 128 /* VLAN Filter Table (4096 bits) */ +#define E1000_NUM_UNICAST_ICH8LAN 7 +#define E1000_MC_TBL_SIZE_ICH8LAN 32 + /* Receive Address Register */ struct e1000_rar { @@ -776,6 +839,7 @@ struct e1000_rar { /* Number of entries in the Multicast Table Array (MTA). */ #define E1000_NUM_MTA_REGISTERS 128 +#define E1000_NUM_MTA_REGISTERS_ICH8LAN 32 /* IPv4 Address Table Entry */ struct e1000_ipv4_at_entry { @@ -786,6 +850,7 @@ struct e1000_ipv4_at_entry { /* Four wakeup IP addresses are supported */ #define E1000_WAKEUP_IP_ADDRESS_COUNT_MAX 4 #define E1000_IP4AT_SIZE E1000_WAKEUP_IP_ADDRESS_COUNT_MAX +#define E1000_IP4AT_SIZE_ICH8LAN 3 #define E1000_IP6AT_SIZE 1 /* IPv6 Address Table Entry */ @@ -844,6 +909,7 @@ struct e1000_ffvt_entry { #define E1000_FLA 0x0001C /* Flash Access - RW */ #define E1000_MDIC 0x00020 /* MDI Control - RW */ #define E1000_SCTL 0x00024 /* SerDes Control - RW */ +#define E1000_FEXTNVM 0x00028 /* Future Extended NVM register */ #define E1000_FCAL 0x00028 /* Flow Control Address Low - RW */ #define E1000_FCAH 0x0002C /* Flow Control Address High -RW */ #define E1000_FCT 0x00030 /* Flow Control Type - RW */ @@ -872,6 +938,8 @@ struct e1000_ffvt_entry { #define E1000_LEDCTL 0x00E00 /* LED Control - RW */ #define E1000_EXTCNF_CTRL 0x00F00 /* Extended Configuration Control */ #define E1000_EXTCNF_SIZE 0x00F08 /* Extended Configuration Size */ +#define E1000_PHY_CTRL 0x00F10 /* PHY Control Register in CSR */ +#define FEXTNVM_SW_CONFIG 0x0001 #define E1000_PBA 0x01000 /* Packet Buffer Allocation - RW */ #define E1000_PBS 0x01008 /* Packet Buffer Size */ #define E1000_EEMNGCTL 0x01010 /* MNG EEprom Control */ @@ -899,11 +967,13 @@ struct e1000_ffvt_entry { #define E1000_RDH0 E1000_RDH /* RX Desc Head (0) - RW */ #define E1000_RDT0 E1000_RDT /* RX Desc Tail (0) - RW */ #define E1000_RDTR0 E1000_RDTR /* RX Delay Timer (0) - RW */ -#define E1000_RXDCTL 0x02828 /* RX Descriptor Control - RW */ +#define E1000_RXDCTL 0x02828 /* RX Descriptor Control queue 0 - RW */ +#define E1000_RXDCTL1 0x02928 /* RX Descriptor Control queue 1 - RW */ #define E1000_RADV 0x0282C /* RX Interrupt Absolute Delay Timer - RW */ #define E1000_RSRPD 0x02C00 /* RX Small Packet Detect - RW */ #define E1000_RAID 0x02C08 /* Receive Ack Interrupt Delay - RW */ #define E1000_TXDMAC 0x03000 /* TX DMA Control - RW */ +#define E1000_KABGTXD 0x03004 /* AFE Band Gap Transmit Ref Data */ #define E1000_TDFH 0x03410 /* TX Data FIFO Head - RW */ #define E1000_TDFT 0x03418 /* TX Data FIFO Tail - RW */ #define E1000_TDFHS 0x03420 /* TX Data FIFO Head Saved - RW */ @@ -1050,6 +1120,7 @@ struct e1000_ffvt_entry { #define E1000_82542_FLA E1000_FLA #define E1000_82542_MDIC E1000_MDIC #define E1000_82542_SCTL E1000_SCTL +#define E1000_82542_FEXTNVM E1000_FEXTNVM #define E1000_82542_FCAL E1000_FCAL #define E1000_82542_FCAH E1000_FCAH #define E1000_82542_FCT E1000_FCT @@ -1073,6 +1144,19 @@ struct e1000_ffvt_entry { #define E1000_82542_RDLEN0 E1000_82542_RDLEN #define E1000_82542_RDH0 E1000_82542_RDH #define E1000_82542_RDT0 E1000_82542_RDT +#define E1000_82542_SRRCTL(_n) (0x280C + ((_n) << 8)) /* Split and Replication + * RX Control - RW */ +#define E1000_82542_DCA_RXCTRL(_n) (0x02814 + ((_n) << 8)) +#define E1000_82542_RDBAH3 0x02B04 /* RX Desc Base High Queue 3 - RW */ +#define E1000_82542_RDBAL3 0x02B00 /* RX Desc Low Queue 3 - RW */ +#define E1000_82542_RDLEN3 0x02B08 /* RX Desc Length Queue 3 - RW */ +#define E1000_82542_RDH3 0x02B10 /* RX Desc Head Queue 3 - RW */ +#define E1000_82542_RDT3 0x02B18 /* RX Desc Tail Queue 3 - RW */ +#define E1000_82542_RDBAL2 0x02A00 /* RX Desc Base Low Queue 2 - RW */ +#define E1000_82542_RDBAH2 0x02A04 /* RX Desc Base High Queue 2 - RW */ +#define E1000_82542_RDLEN2 0x02A08 /* RX Desc Length Queue 2 - RW */ +#define E1000_82542_RDH2 0x02A10 /* RX Desc Head Queue 2 - RW */ +#define E1000_82542_RDT2 0x02A18 /* RX Desc Tail Queue 2 - RW */ #define E1000_82542_RDTR1 0x00130 #define E1000_82542_RDBAL1 0x00138 #define E1000_82542_RDBAH1 0x0013C @@ -1110,11 +1194,14 @@ struct e1000_ffvt_entry { #define E1000_82542_FLOP E1000_FLOP #define E1000_82542_EXTCNF_CTRL E1000_EXTCNF_CTRL #define E1000_82542_EXTCNF_SIZE E1000_EXTCNF_SIZE +#define E1000_82542_PHY_CTRL E1000_PHY_CTRL #define E1000_82542_ERT E1000_ERT #define E1000_82542_RXDCTL E1000_RXDCTL +#define E1000_82542_RXDCTL1 E1000_RXDCTL1 #define E1000_82542_RADV E1000_RADV #define E1000_82542_RSRPD E1000_RSRPD #define E1000_82542_TXDMAC E1000_TXDMAC +#define E1000_82542_KABGTXD E1000_KABGTXD #define E1000_82542_TDFHS E1000_TDFHS #define E1000_82542_TDFTS E1000_TDFTS #define E1000_82542_TDFPC E1000_TDFPC @@ -1310,13 +1397,16 @@ struct e1000_hw_stats { /* Structure containing variables used by the shared code (e1000_hw.c) */ struct e1000_hw { - uint8_t __iomem *hw_addr; + uint8_t *hw_addr; uint8_t *flash_address; e1000_mac_type mac_type; e1000_phy_type phy_type; uint32_t phy_init_script; e1000_media_type media_type; void *back; + struct e1000_shadow_ram *eeprom_shadow_ram; + uint32_t flash_bank_size; + uint32_t flash_base_addr; e1000_fc_type fc; e1000_bus_speed bus_speed; e1000_bus_width bus_width; @@ -1328,6 +1418,7 @@ struct e1000_hw { uint32_t asf_firmware_present; uint32_t eeprom_semaphore_present; uint32_t swfw_sync_present; + uint32_t swfwhw_semaphore_present; unsigned long io_base; uint32_t phy_id; uint32_t phy_revision; @@ -1387,6 +1478,7 @@ struct e1000_hw { boolean_t in_ifs_mode; boolean_t mng_reg_access_disabled; boolean_t leave_av_bit_off; + boolean_t kmrn_lock_loss_workaround_disabled; }; @@ -1435,6 +1527,7 @@ struct e1000_hw { #define E1000_CTRL_RTE 0x20000000 /* Routing tag enable */ #define E1000_CTRL_VME 0x40000000 /* IEEE VLAN mode enable */ #define E1000_CTRL_PHY_RST 0x80000000 /* PHY Reset */ +#define E1000_CTRL_SW2FW_INT 0x02000000 /* Initiate an interrupt to manageability engine */ /* Device Status */ #define E1000_STATUS_FD 0x00000001 /* Full duplex.0=half,1=full */ @@ -1449,6 +1542,8 @@ struct e1000_hw { #define E1000_STATUS_SPEED_10 0x00000000 /* Speed 10Mb/s */ #define E1000_STATUS_SPEED_100 0x00000040 /* Speed 100Mb/s */ #define E1000_STATUS_SPEED_1000 0x00000080 /* Speed 1000Mb/s */ +#define E1000_STATUS_LAN_INIT_DONE 0x00000200 /* Lan Init Completion + by EEPROM/Flash */ #define E1000_STATUS_ASDV 0x00000300 /* Auto speed detect value */ #define E1000_STATUS_DOCK_CI 0x00000800 /* Change in Dock/Undock state. Clear on write '0'. */ #define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Status of Master requests. */ @@ -1506,6 +1601,10 @@ struct e1000_hw { #define E1000_STM_OPCODE 0xDB00 #define E1000_HICR_FW_RESET 0xC0 +#define E1000_SHADOW_RAM_WORDS 2048 +#define E1000_ICH8_NVM_SIG_WORD 0x13 +#define E1000_ICH8_NVM_SIG_MASK 0xC0 + /* EEPROM Read */ #define E1000_EERD_START 0x00000001 /* Start Read */ #define E1000_EERD_DONE 0x00000010 /* Read Done */ @@ -1551,7 +1650,6 @@ struct e1000_hw { #define E1000_CTRL_EXT_WR_WMARK_320 0x01000000 #define E1000_CTRL_EXT_WR_WMARK_384 0x02000000 #define E1000_CTRL_EXT_WR_WMARK_448 0x03000000 -#define E1000_CTRL_EXT_CANC 0x04000000 /* Interrupt delay cancellation */ #define E1000_CTRL_EXT_DRV_LOAD 0x10000000 /* Driver loaded bit for FW */ #define E1000_CTRL_EXT_IAME 0x08000000 /* Interrupt acknowledge Auto-mask */ #define E1000_CTRL_EXT_INT_TIMER_CLR 0x20000000 /* Clear Interrupt timers after IMS clear */ @@ -1591,12 +1689,31 @@ struct e1000_hw { #define E1000_KUMCTRLSTA_FIFO_CTRL_TX_BYPASS 0x00000800 /* In-Band Control */ +#define E1000_KUMCTRLSTA_INB_CTRL_LINK_STATUS_TX_TIMEOUT_DEFAULT 0x00000500 #define E1000_KUMCTRLSTA_INB_CTRL_DIS_PADDING 0x00000010 /* Half-Duplex Control */ #define E1000_KUMCTRLSTA_HD_CTRL_10_100_DEFAULT 0x00000004 #define E1000_KUMCTRLSTA_HD_CTRL_1000_DEFAULT 0x00000000 +#define E1000_KUMCTRLSTA_OFFSET_K0S_CTRL 0x0000001E + +#define E1000_KUMCTRLSTA_DIAG_FELPBK 0x2000 +#define E1000_KUMCTRLSTA_DIAG_NELPBK 0x1000 + +#define E1000_KUMCTRLSTA_K0S_100_EN 0x2000 +#define E1000_KUMCTRLSTA_K0S_GBE_EN 0x1000 +#define E1000_KUMCTRLSTA_K0S_ENTRY_LATENCY_MASK 0x0003 + +#define E1000_KABGTXD_BGSQLBIAS 0x00050000 + +#define E1000_PHY_CTRL_SPD_EN 0x00000001 +#define E1000_PHY_CTRL_D0A_LPLU 0x00000002 +#define E1000_PHY_CTRL_NOND0A_LPLU 0x00000004 +#define E1000_PHY_CTRL_NOND0A_GBE_DISABLE 0x00000008 +#define E1000_PHY_CTRL_GBE_DISABLE 0x00000040 +#define E1000_PHY_CTRL_B2B_EN 0x00000080 + /* LED Control */ #define E1000_LEDCTL_LED0_MODE_MASK 0x0000000F #define E1000_LEDCTL_LED0_MODE_SHIFT 0 @@ -1666,6 +1783,9 @@ struct e1000_hw { #define E1000_ICR_RXD_FIFO_PAR1 0x01000000 /* queue 1 Rx descriptor FIFO parity error */ #define E1000_ICR_TXD_FIFO_PAR1 0x02000000 /* queue 1 Tx descriptor FIFO parity error */ #define E1000_ICR_ALL_PARITY 0x03F00000 /* all parity error bits */ +#define E1000_ICR_DSW 0x00000020 /* FW changed the status of DISSW bit in the FWSM */ +#define E1000_ICR_PHYINT 0x00001000 /* LAN connected device generates an interrupt */ +#define E1000_ICR_EPRST 0x00100000 /* ME handware reset occurs */ /* Interrupt Cause Set */ #define E1000_ICS_TXDW E1000_ICR_TXDW /* Transmit desc written back */ @@ -1692,6 +1812,9 @@ struct e1000_hw { #define E1000_ICS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */ #define E1000_ICS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */ #define E1000_ICS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */ +#define E1000_ICS_DSW E1000_ICR_DSW +#define E1000_ICS_PHYINT E1000_ICR_PHYINT +#define E1000_ICS_EPRST E1000_ICR_EPRST /* Interrupt Mask Set */ #define E1000_IMS_TXDW E1000_ICR_TXDW /* Transmit desc written back */ @@ -1718,6 +1841,9 @@ struct e1000_hw { #define E1000_IMS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */ #define E1000_IMS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */ #define E1000_IMS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */ +#define E1000_IMS_DSW E1000_ICR_DSW +#define E1000_IMS_PHYINT E1000_ICR_PHYINT +#define E1000_IMS_EPRST E1000_ICR_EPRST /* Interrupt Mask Clear */ #define E1000_IMC_TXDW E1000_ICR_TXDW /* Transmit desc written back */ @@ -1744,6 +1870,9 @@ struct e1000_hw { #define E1000_IMC_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */ #define E1000_IMC_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */ #define E1000_IMC_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */ +#define E1000_IMC_DSW E1000_ICR_DSW +#define E1000_IMC_PHYINT E1000_ICR_PHYINT +#define E1000_IMC_EPRST E1000_ICR_EPRST /* Receive Control */ #define E1000_RCTL_RST 0x00000001 /* Software reset */ @@ -1918,9 +2047,10 @@ struct e1000_hw { #define E1000_MRQC_RSS_FIELD_MASK 0xFFFF0000 #define E1000_MRQC_RSS_FIELD_IPV4_TCP 0x00010000 #define E1000_MRQC_RSS_FIELD_IPV4 0x00020000 -#define E1000_MRQC_RSS_FIELD_IPV6_TCP 0x00040000 +#define E1000_MRQC_RSS_FIELD_IPV6_TCP_EX 0x00040000 #define E1000_MRQC_RSS_FIELD_IPV6_EX 0x00080000 #define E1000_MRQC_RSS_FIELD_IPV6 0x00100000 +#define E1000_MRQC_RSS_FIELD_IPV6_TCP 0x00200000 /* Definitions for power management and wakeup registers */ /* Wake Up Control */ @@ -2010,6 +2140,15 @@ struct e1000_hw { #define E1000_FWSM_MODE_SHIFT 1 #define E1000_FWSM_FW_VALID 0x00008000 /* FW established a valid mode */ +#define E1000_FWSM_RSPCIPHY 0x00000040 /* Reset PHY on PCI reset */ +#define E1000_FWSM_DISSW 0x10000000 /* FW disable SW Write Access */ +#define E1000_FWSM_SKUSEL_MASK 0x60000000 /* LAN SKU select */ +#define E1000_FWSM_SKUEL_SHIFT 29 +#define E1000_FWSM_SKUSEL_EMB 0x0 /* Embedded SKU */ +#define E1000_FWSM_SKUSEL_CONS 0x1 /* Consumer SKU */ +#define E1000_FWSM_SKUSEL_PERF_100 0x2 /* Perf & Corp 10/100 SKU */ +#define E1000_FWSM_SKUSEL_PERF_GBE 0x3 /* Perf & Copr GbE SKU */ + /* FFLT Debug Register */ #define E1000_FFLT_DBG_INVC 0x00100000 /* Invalid /C/ code handling */ @@ -2082,6 +2221,8 @@ struct e1000_host_command_info { E1000_GCR_TXDSCW_NO_SNOOP | \ E1000_GCR_TXDSCR_NO_SNOOP) +#define PCI_EX_82566_SNOOP_ALL PCI_EX_NO_SNOOP_ALL + #define E1000_GCR_L1_ACT_WITHOUT_L0S_RX 0x08000000 /* Function Active and Power State to MNG */ #define E1000_FACTPS_FUNC0_POWER_STATE_MASK 0x00000003 @@ -2140,8 +2281,10 @@ struct e1000_host_command_info { #define EEPROM_PHY_CLASS_WORD 0x0007 #define EEPROM_INIT_CONTROL1_REG 0x000A #define EEPROM_INIT_CONTROL2_REG 0x000F +#define EEPROM_SWDEF_PINS_CTRL_PORT_1 0x0010 #define EEPROM_INIT_CONTROL3_PORT_B 0x0014 #define EEPROM_INIT_3GIO_3 0x001A +#define EEPROM_SWDEF_PINS_CTRL_PORT_0 0x0020 #define EEPROM_INIT_CONTROL3_PORT_A 0x0024 #define EEPROM_CFG 0x0012 #define EEPROM_FLASH_VERSION 0x0032 @@ -2153,10 +2296,16 @@ struct e1000_host_command_info { /* Word definitions for ID LED Settings */ #define ID_LED_RESERVED_0000 0x0000 #define ID_LED_RESERVED_FFFF 0xFFFF +#define ID_LED_RESERVED_82573 0xF746 +#define ID_LED_DEFAULT_82573 0x1811 #define ID_LED_DEFAULT ((ID_LED_OFF1_ON2 << 12) | \ (ID_LED_OFF1_OFF2 << 8) | \ (ID_LED_DEF1_DEF2 << 4) | \ (ID_LED_DEF1_DEF2)) +#define ID_LED_DEFAULT_ICH8LAN ((ID_LED_DEF1_DEF2 << 12) | \ + (ID_LED_DEF1_OFF2 << 8) | \ + (ID_LED_DEF1_ON2 << 4) | \ + (ID_LED_DEF1_DEF2)) #define ID_LED_DEF1_DEF2 0x1 #define ID_LED_DEF1_ON2 0x2 #define ID_LED_DEF1_OFF2 0x3 @@ -2191,6 +2340,11 @@ struct e1000_host_command_info { #define EEPROM_WORD0F_ASM_DIR 0x2000 #define EEPROM_WORD0F_ANE 0x0800 #define EEPROM_WORD0F_SWPDIO_EXT 0x00F0 +#define EEPROM_WORD0F_LPLU 0x0001 + +/* Mask bits for fields in Word 0x10/0x20 of the EEPROM */ +#define EEPROM_WORD1020_GIGA_DISABLE 0x0010 +#define EEPROM_WORD1020_GIGA_DISABLE_NON_D0A 0x0008 /* Mask bits for fields in Word 0x1a of the EEPROM */ #define EEPROM_WORD1A_ASPM_MASK 0x000C @@ -2265,23 +2419,29 @@ struct e1000_host_command_info { #define E1000_EXTCNF_CTRL_D_UD_OWNER 0x00000010 #define E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP 0x00000020 #define E1000_EXTCNF_CTRL_MDIO_HW_OWNERSHIP 0x00000040 -#define E1000_EXTCNF_CTRL_EXT_CNF_POINTER 0x1FFF0000 +#define E1000_EXTCNF_CTRL_EXT_CNF_POINTER 0x0FFF0000 #define E1000_EXTCNF_SIZE_EXT_PHY_LENGTH 0x000000FF #define E1000_EXTCNF_SIZE_EXT_DOCK_LENGTH 0x0000FF00 #define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH 0x00FF0000 +#define E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE 0x00000001 +#define E1000_EXTCNF_CTRL_SWFLAG 0x00000020 /* PBA constants */ +#define E1000_PBA_8K 0x0008 /* 8KB, default Rx allocation */ #define E1000_PBA_12K 0x000C /* 12KB, default Rx allocation */ #define E1000_PBA_16K 0x0010 /* 16KB, default TX allocation */ #define E1000_PBA_22K 0x0016 #define E1000_PBA_24K 0x0018 #define E1000_PBA_30K 0x001E #define E1000_PBA_32K 0x0020 +#define E1000_PBA_34K 0x0022 #define E1000_PBA_38K 0x0026 #define E1000_PBA_40K 0x0028 #define E1000_PBA_48K 0x0030 /* 48KB, default RX allocation */ +#define E1000_PBS_16K E1000_PBA_16K + /* Flow Control Constants */ #define FLOW_CONTROL_ADDRESS_LOW 0x00C28001 #define FLOW_CONTROL_ADDRESS_HIGH 0x00000100 @@ -2336,7 +2496,7 @@ struct e1000_host_command_info { /* Number of milliseconds we wait for Eeprom auto read bit done after MAC reset */ #define AUTO_READ_DONE_TIMEOUT 10 /* Number of milliseconds we wait for PHY configuration done after MAC reset */ -#define PHY_CFG_TIMEOUT 40 +#define PHY_CFG_TIMEOUT 100 #define E1000_TX_BUFFER_SIZE ((uint32_t)1514) @@ -2764,6 +2924,17 @@ struct e1000_host_command_info { #define M88E1000_EPSCR_TX_CLK_25 0x0070 /* 25 MHz TX_CLK */ #define M88E1000_EPSCR_TX_CLK_0 0x0000 /* NO TX_CLK */ +/* M88EC018 Rev 2 specific DownShift settings */ +#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK 0x0E00 +#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_1X 0x0000 +#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_2X 0x0200 +#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_3X 0x0400 +#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_4X 0x0600 +#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X 0x0800 +#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_6X 0x0A00 +#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_7X 0x0C00 +#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_8X 0x0E00 + /* IGP01E1000 Specific Port Config Register - R/W */ #define IGP01E1000_PSCFR_AUTO_MDIX_PAR_DETECT 0x0010 #define IGP01E1000_PSCFR_PRE_EN 0x0020 @@ -2990,6 +3161,221 @@ struct e1000_host_command_info { #define L1LXT971A_PHY_ID 0x001378E0 #define GG82563_E_PHY_ID 0x01410CA0 + +/* Bits... + * 15-5: page + * 4-0: register offset + */ +#define PHY_PAGE_SHIFT 5 +#define PHY_REG(page, reg) \ + (((page) << PHY_PAGE_SHIFT) | ((reg) & MAX_PHY_REG_ADDRESS)) + +#define IGP3_PHY_PORT_CTRL \ + PHY_REG(769, 17) /* Port General Configuration */ +#define IGP3_PHY_RATE_ADAPT_CTRL \ + PHY_REG(769, 25) /* Rate Adapter Control Register */ + +#define IGP3_KMRN_FIFO_CTRL_STATS \ + PHY_REG(770, 16) /* KMRN FIFO's control/status register */ +#define IGP3_KMRN_POWER_MNG_CTRL \ + PHY_REG(770, 17) /* KMRN Power Management Control Register */ +#define IGP3_KMRN_INBAND_CTRL \ + PHY_REG(770, 18) /* KMRN Inband Control Register */ +#define IGP3_KMRN_DIAG \ + PHY_REG(770, 19) /* KMRN Diagnostic register */ +#define IGP3_KMRN_DIAG_PCS_LOCK_LOSS 0x0002 /* RX PCS is not synced */ +#define IGP3_KMRN_ACK_TIMEOUT \ + PHY_REG(770, 20) /* KMRN Acknowledge Timeouts register */ + +#define IGP3_VR_CTRL \ + PHY_REG(776, 18) /* Voltage regulator control register */ +#define IGP3_VR_CTRL_MODE_SHUT 0x0200 /* Enter powerdown, shutdown VRs */ + +#define IGP3_CAPABILITY \ + PHY_REG(776, 19) /* IGP3 Capability Register */ + +/* Capabilities for SKU Control */ +#define IGP3_CAP_INITIATE_TEAM 0x0001 /* Able to initiate a team */ +#define IGP3_CAP_WFM 0x0002 /* Support WoL and PXE */ +#define IGP3_CAP_ASF 0x0004 /* Support ASF */ +#define IGP3_CAP_LPLU 0x0008 /* Support Low Power Link Up */ +#define IGP3_CAP_DC_AUTO_SPEED 0x0010 /* Support AC/DC Auto Link Speed */ +#define IGP3_CAP_SPD 0x0020 /* Support Smart Power Down */ +#define IGP3_CAP_MULT_QUEUE 0x0040 /* Support 2 tx & 2 rx queues */ +#define IGP3_CAP_RSS 0x0080 /* Support RSS */ +#define IGP3_CAP_8021PQ 0x0100 /* Support 802.1Q & 802.1p */ +#define IGP3_CAP_AMT_CB 0x0200 /* Support active manageability and circuit breaker */ + +#define IGP3_PPC_JORDAN_EN 0x0001 +#define IGP3_PPC_JORDAN_GIGA_SPEED 0x0002 + +#define IGP3_KMRN_PMC_EE_IDLE_LINK_DIS 0x0001 +#define IGP3_KMRN_PMC_K0S_ENTRY_LATENCY_MASK 0x001E +#define IGP3_KMRN_PMC_K0S_MODE1_EN_GIGA 0x0020 +#define IGP3_KMRN_PMC_K0S_MODE1_EN_100 0x0040 + +#define IGP3E1000_PHY_MISC_CTRL 0x1B /* Misc. Ctrl register */ +#define IGP3_PHY_MISC_DUPLEX_MANUAL_SET 0x1000 /* Duplex Manual Set */ + +#define IGP3_KMRN_EXT_CTRL PHY_REG(770, 18) +#define IGP3_KMRN_EC_DIS_INBAND 0x0080 + +#define IGP03E1000_E_PHY_ID 0x02A80390 +#define IFE_E_PHY_ID 0x02A80330 /* 10/100 PHY */ +#define IFE_PLUS_E_PHY_ID 0x02A80320 +#define IFE_C_E_PHY_ID 0x02A80310 + +#define IFE_PHY_EXTENDED_STATUS_CONTROL 0x10 /* 100BaseTx Extended Status, Control and Address */ +#define IFE_PHY_SPECIAL_CONTROL 0x11 /* 100BaseTx PHY special control register */ +#define IFE_PHY_RCV_FALSE_CARRIER 0x13 /* 100BaseTx Receive False Carrier Counter */ +#define IFE_PHY_RCV_DISCONNECT 0x14 /* 100BaseTx Receive Disconnet Counter */ +#define IFE_PHY_RCV_ERROT_FRAME 0x15 /* 100BaseTx Receive Error Frame Counter */ +#define IFE_PHY_RCV_SYMBOL_ERR 0x16 /* Receive Symbol Error Counter */ +#define IFE_PHY_PREM_EOF_ERR 0x17 /* 100BaseTx Receive Premature End Of Frame Error Counter */ +#define IFE_PHY_RCV_EOF_ERR 0x18 /* 10BaseT Receive End Of Frame Error Counter */ +#define IFE_PHY_TX_JABBER_DETECT 0x19 /* 10BaseT Transmit Jabber Detect Counter */ +#define IFE_PHY_EQUALIZER 0x1A /* PHY Equalizer Control and Status */ +#define IFE_PHY_SPECIAL_CONTROL_LED 0x1B /* PHY special control and LED configuration */ +#define IFE_PHY_MDIX_CONTROL 0x1C /* MDI/MDI-X Control register */ +#define IFE_PHY_HWI_CONTROL 0x1D /* Hardware Integrity Control (HWI) */ + +#define IFE_PESC_REDUCED_POWER_DOWN_DISABLE 0x2000 /* Defaut 1 = Disable auto reduced power down */ +#define IFE_PESC_100BTX_POWER_DOWN 0x0400 /* Indicates the power state of 100BASE-TX */ +#define IFE_PESC_10BTX_POWER_DOWN 0x0200 /* Indicates the power state of 10BASE-T */ +#define IFE_PESC_POLARITY_REVERSED 0x0100 /* Indicates 10BASE-T polarity */ +#define IFE_PESC_PHY_ADDR_MASK 0x007C /* Bit 6:2 for sampled PHY address */ +#define IFE_PESC_SPEED 0x0002 /* Auto-negotiation speed result 1=100Mbs, 0=10Mbs */ +#define IFE_PESC_DUPLEX 0x0001 /* Auto-negotiation duplex result 1=Full, 0=Half */ +#define IFE_PESC_POLARITY_REVERSED_SHIFT 8 + +#define IFE_PSC_DISABLE_DYNAMIC_POWER_DOWN 0x0100 /* 1 = Dyanmic Power Down disabled */ +#define IFE_PSC_FORCE_POLARITY 0x0020 /* 1=Reversed Polarity, 0=Normal */ +#define IFE_PSC_AUTO_POLARITY_DISABLE 0x0010 /* 1=Auto Polarity Disabled, 0=Enabled */ +#define IFE_PSC_JABBER_FUNC_DISABLE 0x0001 /* 1=Jabber Disabled, 0=Normal Jabber Operation */ +#define IFE_PSC_FORCE_POLARITY_SHIFT 5 +#define IFE_PSC_AUTO_POLARITY_DISABLE_SHIFT 4 + +#define IFE_PMC_AUTO_MDIX 0x0080 /* 1=enable MDI/MDI-X feature, default 0=disabled */ +#define IFE_PMC_FORCE_MDIX 0x0040 /* 1=force MDIX-X, 0=force MDI */ +#define IFE_PMC_MDIX_STATUS 0x0020 /* 1=MDI-X, 0=MDI */ +#define IFE_PMC_AUTO_MDIX_COMPLETE 0x0010 /* Resolution algorthm is completed */ +#define IFE_PMC_MDIX_MODE_SHIFT 6 +#define IFE_PHC_MDIX_RESET_ALL_MASK 0x0000 /* Disable auto MDI-X */ + +#define IFE_PHC_HWI_ENABLE 0x8000 /* Enable the HWI feature */ +#define IFE_PHC_ABILITY_CHECK 0x4000 /* 1= Test Passed, 0=failed */ +#define IFE_PHC_TEST_EXEC 0x2000 /* PHY launch test pulses on the wire */ +#define IFE_PHC_HIGHZ 0x0200 /* 1 = Open Circuit */ +#define IFE_PHC_LOWZ 0x0400 /* 1 = Short Circuit */ +#define IFE_PHC_LOW_HIGH_Z_MASK 0x0600 /* Mask for indication type of problem on the line */ +#define IFE_PHC_DISTANCE_MASK 0x01FF /* Mask for distance to the cable problem, in 80cm granularity */ +#define IFE_PHC_RESET_ALL_MASK 0x0000 /* Disable HWI */ +#define IFE_PSCL_PROBE_MODE 0x0020 /* LED Probe mode */ +#define IFE_PSCL_PROBE_LEDS_OFF 0x0006 /* Force LEDs 0 and 2 off */ +#define IFE_PSCL_PROBE_LEDS_ON 0x0007 /* Force LEDs 0 and 2 on */ + +#define ICH8_FLASH_COMMAND_TIMEOUT 500 /* 500 ms , should be adjusted */ +#define ICH8_FLASH_CYCLE_REPEAT_COUNT 10 /* 10 cycles , should be adjusted */ +#define ICH8_FLASH_SEG_SIZE_256 256 +#define ICH8_FLASH_SEG_SIZE_4K 4096 +#define ICH8_FLASH_SEG_SIZE_64K 65536 + +#define ICH8_CYCLE_READ 0x0 +#define ICH8_CYCLE_RESERVED 0x1 +#define ICH8_CYCLE_WRITE 0x2 +#define ICH8_CYCLE_ERASE 0x3 + +#define ICH8_FLASH_GFPREG 0x0000 +#define ICH8_FLASH_HSFSTS 0x0004 +#define ICH8_FLASH_HSFCTL 0x0006 +#define ICH8_FLASH_FADDR 0x0008 +#define ICH8_FLASH_FDATA0 0x0010 +#define ICH8_FLASH_FRACC 0x0050 +#define ICH8_FLASH_FREG0 0x0054 +#define ICH8_FLASH_FREG1 0x0058 +#define ICH8_FLASH_FREG2 0x005C +#define ICH8_FLASH_FREG3 0x0060 +#define ICH8_FLASH_FPR0 0x0074 +#define ICH8_FLASH_FPR1 0x0078 +#define ICH8_FLASH_SSFSTS 0x0090 +#define ICH8_FLASH_SSFCTL 0x0092 +#define ICH8_FLASH_PREOP 0x0094 +#define ICH8_FLASH_OPTYPE 0x0096 +#define ICH8_FLASH_OPMENU 0x0098 + +#define ICH8_FLASH_REG_MAPSIZE 0x00A0 +#define ICH8_FLASH_SECTOR_SIZE 4096 +#define ICH8_GFPREG_BASE_MASK 0x1FFF +#define ICH8_FLASH_LINEAR_ADDR_MASK 0x00FFFFFF + +/* ICH8 GbE Flash Hardware Sequencing Flash Status Register bit breakdown */ +/* Offset 04h HSFSTS */ +union ich8_hws_flash_status { + struct ich8_hsfsts { +#ifdef E1000_BIG_ENDIAN + uint16_t reserved2 :6; + uint16_t fldesvalid :1; + uint16_t flockdn :1; + uint16_t flcdone :1; + uint16_t flcerr :1; + uint16_t dael :1; + uint16_t berasesz :2; + uint16_t flcinprog :1; + uint16_t reserved1 :2; +#else + uint16_t flcdone :1; /* bit 0 Flash Cycle Done */ + uint16_t flcerr :1; /* bit 1 Flash Cycle Error */ + uint16_t dael :1; /* bit 2 Direct Access error Log */ + uint16_t berasesz :2; /* bit 4:3 Block/Sector Erase Size */ + uint16_t flcinprog :1; /* bit 5 flash SPI cycle in Progress */ + uint16_t reserved1 :2; /* bit 13:6 Reserved */ + uint16_t reserved2 :6; /* bit 13:6 Reserved */ + uint16_t fldesvalid :1; /* bit 14 Flash Descriptor Valid */ + uint16_t flockdn :1; /* bit 15 Flash Configuration Lock-Down */ +#endif + } hsf_status; + uint16_t regval; +}; + +/* ICH8 GbE Flash Hardware Sequencing Flash control Register bit breakdown */ +/* Offset 06h FLCTL */ +union ich8_hws_flash_ctrl { + struct ich8_hsflctl { +#ifdef E1000_BIG_ENDIAN + uint16_t fldbcount :2; + uint16_t flockdn :6; + uint16_t flcgo :1; + uint16_t flcycle :2; + uint16_t reserved :5; +#else + uint16_t flcgo :1; /* 0 Flash Cycle Go */ + uint16_t flcycle :2; /* 2:1 Flash Cycle */ + uint16_t reserved :5; /* 7:3 Reserved */ + uint16_t fldbcount :2; /* 9:8 Flash Data Byte Count */ + uint16_t flockdn :6; /* 15:10 Reserved */ +#endif + } hsf_ctrl; + uint16_t regval; +}; + +/* ICH8 Flash Region Access Permissions */ +union ich8_hws_flash_regacc { + struct ich8_flracc { +#ifdef E1000_BIG_ENDIAN + uint32_t gmwag :8; + uint32_t gmrag :8; + uint32_t grwa :8; + uint32_t grra :8; +#else + uint32_t grra :8; /* 0:7 GbE region Read Access */ + uint32_t grwa :8; /* 8:15 GbE region Write Access */ + uint32_t gmrag :8; /* 23:16 GbE Master Read Access Grant */ + uint32_t gmwag :8; /* 31:24 GbE Master Write Access Grant */ +#endif + } hsf_flregacc; + uint16_t regval; +}; + /* Miscellaneous PHY bit definitions. */ #define PHY_PREAMBLE 0xFFFFFFFF #define PHY_SOF 0x01 diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c index f77624f5f17..f06b281c8f6 100644 --- a/drivers/net/e1000/e1000_main.c +++ b/drivers/net/e1000/e1000_main.c @@ -36,7 +36,7 @@ static char e1000_driver_string[] = "Intel(R) PRO/1000 Network Driver"; #else #define DRIVERNAPI "-NAPI" #endif -#define DRV_VERSION "7.0.38-k4"DRIVERNAPI +#define DRV_VERSION "7.1.9-k2"DRIVERNAPI char e1000_driver_version[] = DRV_VERSION; static char e1000_copyright[] = "Copyright (c) 1999-2006 Intel Corporation."; @@ -73,6 +73,11 @@ static struct pci_device_id e1000_pci_tbl[] = { INTEL_E1000_ETHERNET_DEVICE(0x1026), INTEL_E1000_ETHERNET_DEVICE(0x1027), INTEL_E1000_ETHERNET_DEVICE(0x1028), + INTEL_E1000_ETHERNET_DEVICE(0x1049), + INTEL_E1000_ETHERNET_DEVICE(0x104A), + INTEL_E1000_ETHERNET_DEVICE(0x104B), + INTEL_E1000_ETHERNET_DEVICE(0x104C), + INTEL_E1000_ETHERNET_DEVICE(0x104D), INTEL_E1000_ETHERNET_DEVICE(0x105E), INTEL_E1000_ETHERNET_DEVICE(0x105F), INTEL_E1000_ETHERNET_DEVICE(0x1060), @@ -96,6 +101,8 @@ static struct pci_device_id e1000_pci_tbl[] = { INTEL_E1000_ETHERNET_DEVICE(0x109A), INTEL_E1000_ETHERNET_DEVICE(0x10B5), INTEL_E1000_ETHERNET_DEVICE(0x10B9), + INTEL_E1000_ETHERNET_DEVICE(0x10BA), + INTEL_E1000_ETHERNET_DEVICE(0x10BB), /* required last entry */ {0,} }; @@ -133,7 +140,6 @@ static void e1000_clean_rx_ring(struct e1000_adapter *adapter, static void e1000_set_multi(struct net_device *netdev); static void e1000_update_phy_info(unsigned long data); static void e1000_watchdog(unsigned long data); -static void e1000_watchdog_task(struct e1000_adapter *adapter); static void e1000_82547_tx_fifo_stall(unsigned long data); static int e1000_xmit_frame(struct sk_buff *skb, struct net_device *netdev); static struct net_device_stats * e1000_get_stats(struct net_device *netdev); @@ -178,8 +184,8 @@ static void e1000_vlan_rx_add_vid(struct net_device *netdev, uint16_t vid); static void e1000_vlan_rx_kill_vid(struct net_device *netdev, uint16_t vid); static void e1000_restore_vlan(struct e1000_adapter *adapter); -#ifdef CONFIG_PM static int e1000_suspend(struct pci_dev *pdev, pm_message_t state); +#ifdef CONFIG_PM static int e1000_resume(struct pci_dev *pdev); #endif static void e1000_shutdown(struct pci_dev *pdev); @@ -206,8 +212,8 @@ static struct pci_driver e1000_driver = { .probe = e1000_probe, .remove = __devexit_p(e1000_remove), /* Power Managment Hooks */ -#ifdef CONFIG_PM .suspend = e1000_suspend, +#ifdef CONFIG_PM .resume = e1000_resume, #endif .shutdown = e1000_shutdown, @@ -261,6 +267,44 @@ e1000_exit_module(void) module_exit(e1000_exit_module); +static int e1000_request_irq(struct e1000_adapter *adapter) +{ + struct net_device *netdev = adapter->netdev; + int flags, err = 0; + + flags = IRQF_SHARED; +#ifdef CONFIG_PCI_MSI + if (adapter->hw.mac_type > e1000_82547_rev_2) { + adapter->have_msi = TRUE; + if ((err = pci_enable_msi(adapter->pdev))) { + DPRINTK(PROBE, ERR, + "Unable to allocate MSI interrupt Error: %d\n", err); + adapter->have_msi = FALSE; + } + } + if (adapter->have_msi) + flags &= ~SA_SHIRQ; +#endif + if ((err = request_irq(adapter->pdev->irq, &e1000_intr, flags, + netdev->name, netdev))) + DPRINTK(PROBE, ERR, + "Unable to allocate interrupt Error: %d\n", err); + + return err; +} + +static void e1000_free_irq(struct e1000_adapter *adapter) +{ + struct net_device *netdev = adapter->netdev; + + free_irq(adapter->pdev->irq, netdev); + +#ifdef CONFIG_PCI_MSI + if (adapter->have_msi) + pci_disable_msi(adapter->pdev); +#endif +} + /** * e1000_irq_disable - Mask off interrupt generation on the NIC * @adapter: board private structure @@ -329,6 +373,7 @@ e1000_release_hw_control(struct e1000_adapter *adapter) { uint32_t ctrl_ext; uint32_t swsm; + uint32_t extcnf; /* Let firmware taken over control of h/w */ switch (adapter->hw.mac_type) { @@ -343,6 +388,11 @@ e1000_release_hw_control(struct e1000_adapter *adapter) swsm = E1000_READ_REG(&adapter->hw, SWSM); E1000_WRITE_REG(&adapter->hw, SWSM, swsm & ~E1000_SWSM_DRV_LOAD); + case e1000_ich8lan: + extcnf = E1000_READ_REG(&adapter->hw, CTRL_EXT); + E1000_WRITE_REG(&adapter->hw, CTRL_EXT, + extcnf & ~E1000_CTRL_EXT_DRV_LOAD); + break; default: break; } @@ -364,6 +414,7 @@ e1000_get_hw_control(struct e1000_adapter *adapter) { uint32_t ctrl_ext; uint32_t swsm; + uint32_t extcnf; /* Let firmware know the driver has taken over */ switch (adapter->hw.mac_type) { case e1000_82571: @@ -378,6 +429,11 @@ e1000_get_hw_control(struct e1000_adapter *adapter) E1000_WRITE_REG(&adapter->hw, SWSM, swsm | E1000_SWSM_DRV_LOAD); break; + case e1000_ich8lan: + extcnf = E1000_READ_REG(&adapter->hw, EXTCNF_CTRL); + E1000_WRITE_REG(&adapter->hw, EXTCNF_CTRL, + extcnf | E1000_EXTCNF_CTRL_SWFLAG); + break; default: break; } @@ -387,18 +443,10 @@ int e1000_up(struct e1000_adapter *adapter) { struct net_device *netdev = adapter->netdev; - int i, err; + int i; /* hardware has been reset, we need to reload some things */ - /* Reset the PHY if it was previously powered down */ - if (adapter->hw.media_type == e1000_media_type_copper) { - uint16_t mii_reg; - e1000_read_phy_reg(&adapter->hw, PHY_CTRL, &mii_reg); - if (mii_reg & MII_CR_POWER_DOWN) - e1000_phy_hw_reset(&adapter->hw); - } - e1000_set_multi(netdev); e1000_restore_vlan(adapter); @@ -415,24 +463,6 @@ e1000_up(struct e1000_adapter *adapter) E1000_DESC_UNUSED(ring)); } -#ifdef CONFIG_PCI_MSI - if (adapter->hw.mac_type > e1000_82547_rev_2) { - adapter->have_msi = TRUE; - if ((err = pci_enable_msi(adapter->pdev))) { - DPRINTK(PROBE, ERR, - "Unable to allocate MSI interrupt Error: %d\n", err); - adapter->have_msi = FALSE; - } - } -#endif - if ((err = request_irq(adapter->pdev->irq, &e1000_intr, - IRQF_SHARED | IRQF_SAMPLE_RANDOM, - netdev->name, netdev))) { - DPRINTK(PROBE, ERR, - "Unable to allocate interrupt Error: %d\n", err); - return err; - } - adapter->tx_queue_len = netdev->tx_queue_len; mod_timer(&adapter->watchdog_timer, jiffies); @@ -445,21 +475,60 @@ e1000_up(struct e1000_adapter *adapter) return 0; } +/** + * e1000_power_up_phy - restore link in case the phy was powered down + * @adapter: address of board private structure + * + * The phy may be powered down to save power and turn off link when the + * driver is unloaded and wake on lan is not enabled (among others) + * *** this routine MUST be followed by a call to e1000_reset *** + * + **/ + +static void e1000_power_up_phy(struct e1000_adapter *adapter) +{ + uint16_t mii_reg = 0; + + /* Just clear the power down bit to wake the phy back up */ + if (adapter->hw.media_type == e1000_media_type_copper) { + /* according to the manual, the phy will retain its + * settings across a power-down/up cycle */ + e1000_read_phy_reg(&adapter->hw, PHY_CTRL, &mii_reg); + mii_reg &= ~MII_CR_POWER_DOWN; + e1000_write_phy_reg(&adapter->hw, PHY_CTRL, mii_reg); + } +} + +static void e1000_power_down_phy(struct e1000_adapter *adapter) +{ + boolean_t mng_mode_enabled = (adapter->hw.mac_type >= e1000_82571) && + e1000_check_mng_mode(&adapter->hw); + /* Power down the PHY so no link is implied when interface is down + * The PHY cannot be powered down if any of the following is TRUE + * (a) WoL is enabled + * (b) AMT is active + * (c) SoL/IDER session is active */ + if (!adapter->wol && adapter->hw.mac_type >= e1000_82540 && + adapter->hw.mac_type != e1000_ich8lan && + adapter->hw.media_type == e1000_media_type_copper && + !(E1000_READ_REG(&adapter->hw, MANC) & E1000_MANC_SMBUS_EN) && + !mng_mode_enabled && + !e1000_check_phy_reset_block(&adapter->hw)) { + uint16_t mii_reg = 0; + e1000_read_phy_reg(&adapter->hw, PHY_CTRL, &mii_reg); + mii_reg |= MII_CR_POWER_DOWN; + e1000_write_phy_reg(&adapter->hw, PHY_CTRL, mii_reg); + mdelay(1); + } +} + void e1000_down(struct e1000_adapter *adapter) { struct net_device *netdev = adapter->netdev; - boolean_t mng_mode_enabled = (adapter->hw.mac_type >= e1000_82571) && - e1000_check_mng_mode(&adapter->hw); e1000_irq_disable(adapter); - free_irq(adapter->pdev->irq, netdev); -#ifdef CONFIG_PCI_MSI - if (adapter->hw.mac_type > e1000_82547_rev_2 && - adapter->have_msi == TRUE) - pci_disable_msi(adapter->pdev); -#endif del_timer_sync(&adapter->tx_fifo_stall_timer); del_timer_sync(&adapter->watchdog_timer); del_timer_sync(&adapter->phy_info_timer); @@ -476,23 +545,17 @@ e1000_down(struct e1000_adapter *adapter) e1000_reset(adapter); e1000_clean_all_tx_rings(adapter); e1000_clean_all_rx_rings(adapter); +} - /* Power down the PHY so no link is implied when interface is down * - * The PHY cannot be powered down if any of the following is TRUE * - * (a) WoL is enabled - * (b) AMT is active - * (c) SoL/IDER session is active */ - if (!adapter->wol && adapter->hw.mac_type >= e1000_82540 && - adapter->hw.media_type == e1000_media_type_copper && - !(E1000_READ_REG(&adapter->hw, MANC) & E1000_MANC_SMBUS_EN) && - !mng_mode_enabled && - !e1000_check_phy_reset_block(&adapter->hw)) { - uint16_t mii_reg; - e1000_read_phy_reg(&adapter->hw, PHY_CTRL, &mii_reg); - mii_reg |= MII_CR_POWER_DOWN; - e1000_write_phy_reg(&adapter->hw, PHY_CTRL, mii_reg); - mdelay(1); - } +void +e1000_reinit_locked(struct e1000_adapter *adapter) +{ + WARN_ON(in_interrupt()); + while (test_and_set_bit(__E1000_RESETTING, &adapter->flags)) + msleep(1); + e1000_down(adapter); + e1000_up(adapter); + clear_bit(__E1000_RESETTING, &adapter->flags); } void @@ -518,6 +581,9 @@ e1000_reset(struct e1000_adapter *adapter) case e1000_82573: pba = E1000_PBA_12K; break; + case e1000_ich8lan: + pba = E1000_PBA_8K; + break; default: pba = E1000_PBA_48K; break; @@ -542,6 +608,12 @@ e1000_reset(struct e1000_adapter *adapter) /* Set the FC high water mark to 90% of the FIFO size. * Required to clear last 3 LSB */ fc_high_water_mark = ((pba * 9216)/10) & 0xFFF8; + /* We can't use 90% on small FIFOs because the remainder + * would be less than 1 full frame. In this case, we size + * it to allow at least a full frame above the high water + * mark. */ + if (pba < E1000_PBA_16K) + fc_high_water_mark = (pba * 1024) - 1600; adapter->hw.fc_high_water = fc_high_water_mark; adapter->hw.fc_low_water = fc_high_water_mark - 8; @@ -564,6 +636,23 @@ e1000_reset(struct e1000_adapter *adapter) e1000_reset_adaptive(&adapter->hw); e1000_phy_get_info(&adapter->hw, &adapter->phy_info); + + if (!adapter->smart_power_down && + (adapter->hw.mac_type == e1000_82571 || + adapter->hw.mac_type == e1000_82572)) { + uint16_t phy_data = 0; + /* speed up time to link by disabling smart power down, ignore + * the return value of this function because there is nothing + * different we would do if it failed */ + e1000_read_phy_reg(&adapter->hw, IGP02E1000_PHY_POWER_MGMT, + &phy_data); + phy_data &= ~IGP02E1000_PM_SPD; + e1000_write_phy_reg(&adapter->hw, IGP02E1000_PHY_POWER_MGMT, + phy_data); + } + + if (adapter->hw.mac_type < e1000_ich8lan) + /* FIXME: this code is duplicate and wrong for PCI Express */ if (adapter->en_mng_pt) { manc = E1000_READ_REG(&adapter->hw, MANC); manc |= (E1000_MANC_ARP_EN | E1000_MANC_EN_MNG2HOST); @@ -590,6 +679,7 @@ e1000_probe(struct pci_dev *pdev, struct net_device *netdev; struct e1000_adapter *adapter; unsigned long mmio_start, mmio_len; + unsigned long flash_start, flash_len; static int cards_found = 0; static int e1000_ksp3_port_a = 0; /* global ksp3 port a indication */ @@ -599,10 +689,12 @@ e1000_probe(struct pci_dev *pdev, if ((err = pci_enable_device(pdev))) return err; - if (!(err = pci_set_dma_mask(pdev, DMA_64BIT_MASK))) { + if (!(err = pci_set_dma_mask(pdev, DMA_64BIT_MASK)) && + !(err = pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK))) { pci_using_dac = 1; } else { - if ((err = pci_set_dma_mask(pdev, DMA_32BIT_MASK))) { + if ((err = pci_set_dma_mask(pdev, DMA_32BIT_MASK)) && + (err = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK))) { E1000_ERR("No usable DMA configuration, aborting\n"); return err; } @@ -682,6 +774,19 @@ e1000_probe(struct pci_dev *pdev, if ((err = e1000_sw_init(adapter))) goto err_sw_init; + /* Flash BAR mapping must happen after e1000_sw_init + * because it depends on mac_type */ + if ((adapter->hw.mac_type == e1000_ich8lan) && + (pci_resource_flags(pdev, 1) & IORESOURCE_MEM)) { + flash_start = pci_resource_start(pdev, 1); + flash_len = pci_resource_len(pdev, 1); + adapter->hw.flash_address = ioremap(flash_start, flash_len); + if (!adapter->hw.flash_address) { + err = -EIO; + goto err_flashmap; + } + } + if ((err = e1000_check_phy_reset_block(&adapter->hw))) DPRINTK(PROBE, INFO, "PHY reset is blocked due to SOL/IDER session.\n"); @@ -700,6 +805,8 @@ e1000_probe(struct pci_dev *pdev, NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX | NETIF_F_HW_VLAN_FILTER; + if (adapter->hw.mac_type == e1000_ich8lan) + netdev->features &= ~NETIF_F_HW_VLAN_FILTER; } #ifdef NETIF_F_TSO @@ -715,11 +822,17 @@ e1000_probe(struct pci_dev *pdev, if (pci_using_dac) netdev->features |= NETIF_F_HIGHDMA; - /* hard_start_xmit is safe against parallel locking */ netdev->features |= NETIF_F_LLTX; adapter->en_mng_pt = e1000_enable_mng_pass_thru(&adapter->hw); + /* initialize eeprom parameters */ + + if (e1000_init_eeprom_params(&adapter->hw)) { + E1000_ERR("EEPROM initialization failed\n"); + return -EIO; + } + /* before reading the EEPROM, reset the controller to * put the device in a known good starting state */ @@ -758,9 +871,6 @@ e1000_probe(struct pci_dev *pdev, adapter->watchdog_timer.function = &e1000_watchdog; adapter->watchdog_timer.data = (unsigned long) adapter; - INIT_WORK(&adapter->watchdog_task, - (void (*)(void *))e1000_watchdog_task, adapter); - init_timer(&adapter->phy_info_timer); adapter->phy_info_timer.function = &e1000_update_phy_info; adapter->phy_info_timer.data = (unsigned long) adapter; @@ -790,6 +900,11 @@ e1000_probe(struct pci_dev *pdev, EEPROM_INIT_CONTROL2_REG, 1, &eeprom_data); eeprom_apme_mask = E1000_EEPROM_82544_APM; break; + case e1000_ich8lan: + e1000_read_eeprom(&adapter->hw, + EEPROM_INIT_CONTROL1_REG, 1, &eeprom_data); + eeprom_apme_mask = E1000_EEPROM_ICH8_APME; + break; case e1000_82546: case e1000_82546_rev_3: case e1000_82571: @@ -849,6 +964,9 @@ e1000_probe(struct pci_dev *pdev, return 0; err_register: + if (adapter->hw.flash_address) + iounmap(adapter->hw.flash_address); +err_flashmap: err_sw_init: err_eeprom: iounmap(adapter->hw.hw_addr); @@ -882,6 +1000,7 @@ e1000_remove(struct pci_dev *pdev) flush_scheduled_work(); if (adapter->hw.mac_type >= e1000_82540 && + adapter->hw.mac_type != e1000_ich8lan && adapter->hw.media_type == e1000_media_type_copper) { manc = E1000_READ_REG(&adapter->hw, MANC); if (manc & E1000_MANC_SMBUS_EN) { @@ -910,6 +1029,8 @@ e1000_remove(struct pci_dev *pdev) #endif iounmap(adapter->hw.hw_addr); + if (adapter->hw.flash_address) + iounmap(adapter->hw.flash_address); pci_release_regions(pdev); free_netdev(netdev); @@ -960,13 +1081,6 @@ e1000_sw_init(struct e1000_adapter *adapter) return -EIO; } - /* initialize eeprom parameters */ - - if (e1000_init_eeprom_params(hw)) { - E1000_ERR("EEPROM initialization failed\n"); - return -EIO; - } - switch (hw->mac_type) { default: break; @@ -1078,6 +1192,10 @@ e1000_open(struct net_device *netdev) struct e1000_adapter *adapter = netdev_priv(netdev); int err; + /* disallow open during test */ + if (test_bit(__E1000_DRIVER_TESTING, &adapter->flags)) + return -EBUSY; + /* allocate transmit descriptors */ if ((err = e1000_setup_all_tx_resources(adapter))) @@ -1088,6 +1206,12 @@ e1000_open(struct net_device *netdev) if ((err = e1000_setup_all_rx_resources(adapter))) goto err_setup_rx; + err = e1000_request_irq(adapter); + if (err) + goto err_up; + + e1000_power_up_phy(adapter); + if ((err = e1000_up(adapter))) goto err_up; adapter->mng_vlan_id = E1000_MNG_VLAN_NONE; @@ -1131,7 +1255,10 @@ e1000_close(struct net_device *netdev) { struct e1000_adapter *adapter = netdev_priv(netdev); + WARN_ON(test_bit(__E1000_RESETTING, &adapter->flags)); e1000_down(adapter); + e1000_power_down_phy(adapter); + e1000_free_irq(adapter); e1000_free_all_tx_resources(adapter); e1000_free_all_rx_resources(adapter); @@ -1189,8 +1316,7 @@ e1000_setup_tx_resources(struct e1000_adapter *adapter, int size; size = sizeof(struct e1000_buffer) * txdr->count; - - txdr->buffer_info = vmalloc_node(size, pcibus_to_node(pdev->bus)); + txdr->buffer_info = vmalloc(size); if (!txdr->buffer_info) { DPRINTK(PROBE, ERR, "Unable to allocate memory for the transmit descriptor ring\n"); @@ -1302,11 +1428,11 @@ e1000_configure_tx(struct e1000_adapter *adapter) tdba = adapter->tx_ring[0].dma; tdlen = adapter->tx_ring[0].count * sizeof(struct e1000_tx_desc); - E1000_WRITE_REG(hw, TDBAL, (tdba & 0x00000000ffffffffULL)); - E1000_WRITE_REG(hw, TDBAH, (tdba >> 32)); E1000_WRITE_REG(hw, TDLEN, tdlen); - E1000_WRITE_REG(hw, TDH, 0); + E1000_WRITE_REG(hw, TDBAH, (tdba >> 32)); + E1000_WRITE_REG(hw, TDBAL, (tdba & 0x00000000ffffffffULL)); E1000_WRITE_REG(hw, TDT, 0); + E1000_WRITE_REG(hw, TDH, 0); adapter->tx_ring[0].tdh = E1000_TDH; adapter->tx_ring[0].tdt = E1000_TDT; break; @@ -1418,7 +1544,7 @@ e1000_setup_rx_resources(struct e1000_adapter *adapter, int size, desc_len; size = sizeof(struct e1000_buffer) * rxdr->count; - rxdr->buffer_info = vmalloc_node(size, pcibus_to_node(pdev->bus)); + rxdr->buffer_info = vmalloc(size); if (!rxdr->buffer_info) { DPRINTK(PROBE, ERR, "Unable to allocate memory for the receive descriptor ring\n"); @@ -1560,9 +1686,6 @@ e1000_setup_rctl(struct e1000_adapter *adapter) E1000_RCTL_LBM_NO | E1000_RCTL_RDMTS_HALF | (adapter->hw.mc_filter_type << E1000_RCTL_MO_SHIFT); - if (adapter->hw.mac_type > e1000_82543) - rctl |= E1000_RCTL_SECRC; - if (adapter->hw.tbi_compatibility_on == 1) rctl |= E1000_RCTL_SBP; else @@ -1628,7 +1751,7 @@ e1000_setup_rctl(struct e1000_adapter *adapter) rfctl |= E1000_RFCTL_IPV6_DIS; E1000_WRITE_REG(&adapter->hw, RFCTL, rfctl); - rctl |= E1000_RCTL_DTYP_PS | E1000_RCTL_SECRC; + rctl |= E1000_RCTL_DTYP_PS; psrctl |= adapter->rx_ps_bsize0 >> E1000_PSRCTL_BSIZE0_SHIFT; @@ -1712,11 +1835,11 @@ e1000_configure_rx(struct e1000_adapter *adapter) case 1: default: rdba = adapter->rx_ring[0].dma; - E1000_WRITE_REG(hw, RDBAL, (rdba & 0x00000000ffffffffULL)); - E1000_WRITE_REG(hw, RDBAH, (rdba >> 32)); E1000_WRITE_REG(hw, RDLEN, rdlen); - E1000_WRITE_REG(hw, RDH, 0); + E1000_WRITE_REG(hw, RDBAH, (rdba >> 32)); + E1000_WRITE_REG(hw, RDBAL, (rdba & 0x00000000ffffffffULL)); E1000_WRITE_REG(hw, RDT, 0); + E1000_WRITE_REG(hw, RDH, 0); adapter->rx_ring[0].rdh = E1000_RDH; adapter->rx_ring[0].rdt = E1000_RDT; break; @@ -1741,9 +1864,6 @@ e1000_configure_rx(struct e1000_adapter *adapter) E1000_WRITE_REG(hw, RXCSUM, rxcsum); } - if (hw->mac_type == e1000_82573) - E1000_WRITE_REG(hw, ERT, 0x0100); - /* Enable Receives */ E1000_WRITE_REG(hw, RCTL, rctl); } @@ -2083,6 +2203,12 @@ e1000_set_multi(struct net_device *netdev) uint32_t rctl; uint32_t hash_value; int i, rar_entries = E1000_RAR_ENTRIES; + int mta_reg_count = (hw->mac_type == e1000_ich8lan) ? + E1000_NUM_MTA_REGISTERS_ICH8LAN : + E1000_NUM_MTA_REGISTERS; + + if (adapter->hw.mac_type == e1000_ich8lan) + rar_entries = E1000_RAR_ENTRIES_ICH8LAN; /* reserve RAR[14] for LAA over-write work-around */ if (adapter->hw.mac_type == e1000_82571) @@ -2121,14 +2247,18 @@ e1000_set_multi(struct net_device *netdev) mc_ptr = mc_ptr->next; } else { E1000_WRITE_REG_ARRAY(hw, RA, i << 1, 0); + E1000_WRITE_FLUSH(hw); E1000_WRITE_REG_ARRAY(hw, RA, (i << 1) + 1, 0); + E1000_WRITE_FLUSH(hw); } } /* clear the old settings from the multicast hash table */ - for (i = 0; i < E1000_NUM_MTA_REGISTERS; i++) + for (i = 0; i < mta_reg_count; i++) { E1000_WRITE_REG_ARRAY(hw, MTA, i, 0); + E1000_WRITE_FLUSH(hw); + } /* load any remaining addresses into the hash table */ @@ -2201,19 +2331,19 @@ static void e1000_watchdog(unsigned long data) { struct e1000_adapter *adapter = (struct e1000_adapter *) data; - - /* Do the rest outside of interrupt context */ - schedule_work(&adapter->watchdog_task); -} - -static void -e1000_watchdog_task(struct e1000_adapter *adapter) -{ struct net_device *netdev = adapter->netdev; struct e1000_tx_ring *txdr = adapter->tx_ring; uint32_t link, tctl; + int32_t ret_val; - e1000_check_for_link(&adapter->hw); + ret_val = e1000_check_for_link(&adapter->hw); + if ((ret_val == E1000_ERR_PHY) && + (adapter->hw.phy_type == e1000_phy_igp_3) && + (E1000_READ_REG(&adapter->hw, CTRL) & E1000_PHY_CTRL_GBE_DISABLE)) { + /* See e1000_kumeran_lock_loss_workaround() */ + DPRINTK(LINK, INFO, + "Gigabit has been disabled, downgrading speed\n"); + } if (adapter->hw.mac_type == e1000_82573) { e1000_enable_tx_pkt_filtering(&adapter->hw); if (adapter->mng_vlan_id != adapter->hw.mng_cookie.vlan_id) @@ -2779,9 +2909,10 @@ e1000_xmit_frame(struct sk_buff *skb, struct net_device *netdev) case e1000_82571: case e1000_82572: case e1000_82573: + case e1000_ich8lan: pull_size = min((unsigned int)4, skb->data_len); if (!__pskb_pull_tail(skb, pull_size)) { - printk(KERN_ERR + DPRINTK(DRV, ERR, "__pskb_pull_tail failed.\n"); dev_kfree_skb_any(skb); return NETDEV_TX_OK; @@ -2919,8 +3050,7 @@ e1000_reset_task(struct net_device *netdev) { struct e1000_adapter *adapter = netdev_priv(netdev); - e1000_down(adapter); - e1000_up(adapter); + e1000_reinit_locked(adapter); } /** @@ -2964,6 +3094,7 @@ e1000_change_mtu(struct net_device *netdev, int new_mtu) /* Adapter-specific max frame size limits. */ switch (adapter->hw.mac_type) { case e1000_undefined ... e1000_82542_rev2_1: + case e1000_ich8lan: if (max_frame > MAXIMUM_ETHERNET_FRAME_SIZE) { DPRINTK(PROBE, ERR, "Jumbo Frames not supported.\n"); return -EINVAL; @@ -3026,10 +3157,8 @@ e1000_change_mtu(struct net_device *netdev, int new_mtu) netdev->mtu = new_mtu; - if (netif_running(netdev)) { - e1000_down(adapter); - e1000_up(adapter); - } + if (netif_running(netdev)) + e1000_reinit_locked(adapter); adapter->hw.max_frame_size = max_frame; @@ -3074,12 +3203,15 @@ e1000_update_stats(struct e1000_adapter *adapter) adapter->stats.bprc += E1000_READ_REG(hw, BPRC); adapter->stats.mprc += E1000_READ_REG(hw, MPRC); adapter->stats.roc += E1000_READ_REG(hw, ROC); + + if (adapter->hw.mac_type != e1000_ich8lan) { adapter->stats.prc64 += E1000_READ_REG(hw, PRC64); adapter->stats.prc127 += E1000_READ_REG(hw, PRC127); adapter->stats.prc255 += E1000_READ_REG(hw, PRC255); adapter->stats.prc511 += E1000_READ_REG(hw, PRC511); adapter->stats.prc1023 += E1000_READ_REG(hw, PRC1023); adapter->stats.prc1522 += E1000_READ_REG(hw, PRC1522); + } adapter->stats.symerrs += E1000_READ_REG(hw, SYMERRS); adapter->stats.mpc += E1000_READ_REG(hw, MPC); @@ -3107,12 +3239,16 @@ e1000_update_stats(struct e1000_adapter *adapter) adapter->stats.totl += E1000_READ_REG(hw, TOTL); adapter->stats.toth += E1000_READ_REG(hw, TOTH); adapter->stats.tpr += E1000_READ_REG(hw, TPR); + + if (adapter->hw.mac_type != e1000_ich8lan) { adapter->stats.ptc64 += E1000_READ_REG(hw, PTC64); adapter->stats.ptc127 += E1000_READ_REG(hw, PTC127); adapter->stats.ptc255 += E1000_READ_REG(hw, PTC255); adapter->stats.ptc511 += E1000_READ_REG(hw, PTC511); adapter->stats.ptc1023 += E1000_READ_REG(hw, PTC1023); adapter->stats.ptc1522 += E1000_READ_REG(hw, PTC1522); + } + adapter->stats.mptc += E1000_READ_REG(hw, MPTC); adapter->stats.bptc += E1000_READ_REG(hw, BPTC); @@ -3134,6 +3270,8 @@ e1000_update_stats(struct e1000_adapter *adapter) if (hw->mac_type > e1000_82547_rev_2) { adapter->stats.iac += E1000_READ_REG(hw, IAC); adapter->stats.icrxoc += E1000_READ_REG(hw, ICRXOC); + + if (adapter->hw.mac_type != e1000_ich8lan) { adapter->stats.icrxptc += E1000_READ_REG(hw, ICRXPTC); adapter->stats.icrxatc += E1000_READ_REG(hw, ICRXATC); adapter->stats.ictxptc += E1000_READ_REG(hw, ICTXPTC); @@ -3141,6 +3279,7 @@ e1000_update_stats(struct e1000_adapter *adapter) adapter->stats.ictxqec += E1000_READ_REG(hw, ICTXQEC); adapter->stats.ictxqmtc += E1000_READ_REG(hw, ICTXQMTC); adapter->stats.icrxdmtc += E1000_READ_REG(hw, ICRXDMTC); + } } /* Fill out the OS statistics structure */ @@ -3547,7 +3686,8 @@ e1000_clean_rx_irq(struct e1000_adapter *adapter, /* All receives must fit into a single buffer */ E1000_DBG("%s: Receive packet consumed multiple" " buffers\n", netdev->name); - dev_kfree_skb_irq(skb); + /* recycle */ + buffer_info-> skb = skb; goto next_desc; } @@ -3675,7 +3815,6 @@ e1000_clean_rx_irq_ps(struct e1000_adapter *adapter, buffer_info = &rx_ring->buffer_info[i]; while (staterr & E1000_RXD_STAT_DD) { - buffer_info = &rx_ring->buffer_info[i]; ps_page = &rx_ring->ps_page[i]; ps_page_dma = &rx_ring->ps_page_dma[i]; #ifdef CONFIG_E1000_NAPI @@ -4180,10 +4319,9 @@ e1000_mii_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd) return retval; } } - if (netif_running(adapter->netdev)) { - e1000_down(adapter); - e1000_up(adapter); - } else + if (netif_running(adapter->netdev)) + e1000_reinit_locked(adapter); + else e1000_reset(adapter); break; case M88E1000_PHY_SPEC_CTRL: @@ -4200,10 +4338,9 @@ e1000_mii_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd) case PHY_CTRL: if (mii_reg & MII_CR_POWER_DOWN) break; - if (netif_running(adapter->netdev)) { - e1000_down(adapter); - e1000_up(adapter); - } else + if (netif_running(adapter->netdev)) + e1000_reinit_locked(adapter); + else e1000_reset(adapter); break; } @@ -4277,18 +4414,21 @@ e1000_vlan_rx_register(struct net_device *netdev, struct vlan_group *grp) ctrl |= E1000_CTRL_VME; E1000_WRITE_REG(&adapter->hw, CTRL, ctrl); + if (adapter->hw.mac_type != e1000_ich8lan) { /* enable VLAN receive filtering */ rctl = E1000_READ_REG(&adapter->hw, RCTL); rctl |= E1000_RCTL_VFE; rctl &= ~E1000_RCTL_CFIEN; E1000_WRITE_REG(&adapter->hw, RCTL, rctl); e1000_update_mng_vlan(adapter); + } } else { /* disable VLAN tag insert/strip */ ctrl = E1000_READ_REG(&adapter->hw, CTRL); ctrl &= ~E1000_CTRL_VME; E1000_WRITE_REG(&adapter->hw, CTRL, ctrl); + if (adapter->hw.mac_type != e1000_ich8lan) { /* disable VLAN filtering */ rctl = E1000_READ_REG(&adapter->hw, RCTL); rctl &= ~E1000_RCTL_VFE; @@ -4297,6 +4437,7 @@ e1000_vlan_rx_register(struct net_device *netdev, struct vlan_group *grp) e1000_vlan_rx_kill_vid(netdev, adapter->mng_vlan_id); adapter->mng_vlan_id = E1000_MNG_VLAN_NONE; } + } } e1000_irq_enable(adapter); @@ -4458,12 +4599,16 @@ e1000_suspend(struct pci_dev *pdev, pm_message_t state) struct e1000_adapter *adapter = netdev_priv(netdev); uint32_t ctrl, ctrl_ext, rctl, manc, status; uint32_t wufc = adapter->wol; +#ifdef CONFIG_PM int retval = 0; +#endif netif_device_detach(netdev); - if (netif_running(netdev)) + if (netif_running(netdev)) { + WARN_ON(test_bit(__E1000_RESETTING, &adapter->flags)); e1000_down(adapter); + } #ifdef CONFIG_PM /* Implement our own version of pci_save_state(pdev) because pci- @@ -4521,7 +4666,9 @@ e1000_suspend(struct pci_dev *pdev, pm_message_t state) pci_enable_wake(pdev, PCI_D3cold, 0); } + /* FIXME: this code is incorrect for PCI Express */ if (adapter->hw.mac_type >= e1000_82540 && + adapter->hw.mac_type != e1000_ich8lan && adapter->hw.media_type == e1000_media_type_copper) { manc = E1000_READ_REG(&adapter->hw, MANC); if (manc & E1000_MANC_SMBUS_EN) { @@ -4532,6 +4679,9 @@ e1000_suspend(struct pci_dev *pdev, pm_message_t state) } } + if (adapter->hw.phy_type == e1000_phy_igp_3) + e1000_phy_powerdown_workaround(&adapter->hw); + /* Release control of h/w to f/w. If f/w is AMT enabled, this * would have already happened in close and is redundant. */ e1000_release_hw_control(adapter); @@ -4567,7 +4717,9 @@ e1000_resume(struct pci_dev *pdev) netif_device_attach(netdev); + /* FIXME: this code is incorrect for PCI Express */ if (adapter->hw.mac_type >= e1000_82540 && + adapter->hw.mac_type != e1000_ich8lan && adapter->hw.media_type == e1000_media_type_copper) { manc = E1000_READ_REG(&adapter->hw, MANC); manc &= ~(E1000_MANC_ARP_EN); diff --git a/drivers/net/e1000/e1000_osdep.h b/drivers/net/e1000/e1000_osdep.h index 048d052be29..2d3e8b06cab 100644 --- a/drivers/net/e1000/e1000_osdep.h +++ b/drivers/net/e1000/e1000_osdep.h @@ -127,4 +127,17 @@ typedef enum { #define E1000_WRITE_FLUSH(a) E1000_READ_REG(a, STATUS) +#define E1000_WRITE_ICH8_REG(a, reg, value) ( \ + writel((value), ((a)->flash_address + reg))) + +#define E1000_READ_ICH8_REG(a, reg) ( \ + readl((a)->flash_address + reg)) + +#define E1000_WRITE_ICH8_REG16(a, reg, value) ( \ + writew((value), ((a)->flash_address + reg))) + +#define E1000_READ_ICH8_REG16(a, reg) ( \ + readw((a)->flash_address + reg)) + + #endif /* _E1000_OSDEP_H_ */ diff --git a/drivers/net/e1000/e1000_param.c b/drivers/net/e1000/e1000_param.c index e55f8969a0f..0ef413172c6 100644 --- a/drivers/net/e1000/e1000_param.c +++ b/drivers/net/e1000/e1000_param.c @@ -45,6 +45,16 @@ */ #define E1000_PARAM_INIT { [0 ... E1000_MAX_NIC] = OPTION_UNSET } +/* Module Parameters are always initialized to -1, so that the driver + * can tell the difference between no user specified value or the + * user asking for the default value. + * The true default values are loaded in when e1000_check_options is called. + * + * This is a GCC extension to ANSI C. + * See the item "Labeled Elements in Initializers" in the section + * "Extensions to the C Language Family" of the GCC documentation. + */ + #define E1000_PARAM(X, desc) \ static int __devinitdata X[E1000_MAX_NIC+1] = E1000_PARAM_INIT; \ static int num_##X = 0; \ @@ -183,6 +193,24 @@ E1000_PARAM(RxAbsIntDelay, "Receive Absolute Interrupt Delay"); E1000_PARAM(InterruptThrottleRate, "Interrupt Throttling Rate"); +/* Enable Smart Power Down of the PHY + * + * Valid Range: 0, 1 + * + * Default Value: 0 (disabled) + */ + +E1000_PARAM(SmartPowerDownEnable, "Enable PHY smart power down"); + +/* Enable Kumeran Lock Loss workaround + * + * Valid Range: 0, 1 + * + * Default Value: 1 (enabled) + */ + +E1000_PARAM(KumeranLockLoss, "Enable Kumeran lock loss workaround"); + #define AUTONEG_ADV_DEFAULT 0x2F #define AUTONEG_ADV_MASK 0x2F #define FLOW_CONTROL_DEFAULT FLOW_CONTROL_FULL @@ -296,6 +324,7 @@ e1000_check_options(struct e1000_adapter *adapter) DPRINTK(PROBE, NOTICE, "Warning: no configuration for board #%i\n", bd); DPRINTK(PROBE, NOTICE, "Using defaults for all values\n"); + bd = E1000_MAX_NIC; } { /* Transmit Descriptor Count */ @@ -313,14 +342,9 @@ e1000_check_options(struct e1000_adapter *adapter) opt.arg.r.max = mac_type < e1000_82544 ? E1000_MAX_TXD : E1000_MAX_82544_TXD; - if (num_TxDescriptors > bd) { - tx_ring->count = TxDescriptors[bd]; - e1000_validate_option(&tx_ring->count, &opt, adapter); - E1000_ROUNDUP(tx_ring->count, - REQ_TX_DESCRIPTOR_MULTIPLE); - } else { - tx_ring->count = opt.def; - } + tx_ring->count = TxDescriptors[bd]; + e1000_validate_option(&tx_ring->count, &opt, adapter); + E1000_ROUNDUP(tx_ring->count, REQ_TX_DESCRIPTOR_MULTIPLE); for (i = 0; i < adapter->num_tx_queues; i++) tx_ring[i].count = tx_ring->count; } @@ -339,14 +363,9 @@ e1000_check_options(struct e1000_adapter *adapter) opt.arg.r.max = mac_type < e1000_82544 ? E1000_MAX_RXD : E1000_MAX_82544_RXD; - if (num_RxDescriptors > bd) { - rx_ring->count = RxDescriptors[bd]; - e1000_validate_option(&rx_ring->count, &opt, adapter); - E1000_ROUNDUP(rx_ring->count, - REQ_RX_DESCRIPTOR_MULTIPLE); - } else { - rx_ring->count = opt.def; - } + rx_ring->count = RxDescriptors[bd]; + e1000_validate_option(&rx_ring->count, &opt, adapter); + E1000_ROUNDUP(rx_ring->count, REQ_RX_DESCRIPTOR_MULTIPLE); for (i = 0; i < adapter->num_rx_queues; i++) rx_ring[i].count = rx_ring->count; } @@ -358,13 +377,9 @@ e1000_check_options(struct e1000_adapter *adapter) .def = OPTION_ENABLED }; - if (num_XsumRX > bd) { - int rx_csum = XsumRX[bd]; - e1000_validate_option(&rx_csum, &opt, adapter); - adapter->rx_csum = rx_csum; - } else { - adapter->rx_csum = opt.def; - } + int rx_csum = XsumRX[bd]; + e1000_validate_option(&rx_csum, &opt, adapter); + adapter->rx_csum = rx_csum; } { /* Flow Control */ @@ -384,13 +399,9 @@ e1000_check_options(struct e1000_adapter *adapter) .p = fc_list }} }; - if (num_FlowControl > bd) { - int fc = FlowControl[bd]; - e1000_validate_option(&fc, &opt, adapter); - adapter->hw.fc = adapter->hw.original_fc = fc; - } else { - adapter->hw.fc = adapter->hw.original_fc = opt.def; - } + int fc = FlowControl[bd]; + e1000_validate_option(&fc, &opt, adapter); + adapter->hw.fc = adapter->hw.original_fc = fc; } { /* Transmit Interrupt Delay */ struct e1000_option opt = { @@ -402,13 +413,8 @@ e1000_check_options(struct e1000_adapter *adapter) .max = MAX_TXDELAY }} }; - if (num_TxIntDelay > bd) { - adapter->tx_int_delay = TxIntDelay[bd]; - e1000_validate_option(&adapter->tx_int_delay, &opt, - adapter); - } else { - adapter->tx_int_delay = opt.def; - } + adapter->tx_int_delay = TxIntDelay[bd]; + e1000_validate_option(&adapter->tx_int_delay, &opt, adapter); } { /* Transmit Absolute Interrupt Delay */ struct e1000_option opt = { @@ -420,13 +426,9 @@ e1000_check_options(struct e1000_adapter *adapter) .max = MAX_TXABSDELAY }} }; - if (num_TxAbsIntDelay > bd) { - adapter->tx_abs_int_delay = TxAbsIntDelay[bd]; - e1000_validate_option(&adapter->tx_abs_int_delay, &opt, - adapter); - } else { - adapter->tx_abs_int_delay = opt.def; - } + adapter->tx_abs_int_delay = TxAbsIntDelay[bd]; + e1000_validate_option(&adapter->tx_abs_int_delay, &opt, + adapter); } { /* Receive Interrupt Delay */ struct e1000_option opt = { @@ -438,13 +440,8 @@ e1000_check_options(struct e1000_adapter *adapter) .max = MAX_RXDELAY }} }; - if (num_RxIntDelay > bd) { - adapter->rx_int_delay = RxIntDelay[bd]; - e1000_validate_option(&adapter->rx_int_delay, &opt, - adapter); - } else { - adapter->rx_int_delay = opt.def; - } + adapter->rx_int_delay = RxIntDelay[bd]; + e1000_validate_option(&adapter->rx_int_delay, &opt, adapter); } { /* Receive Absolute Interrupt Delay */ struct e1000_option opt = { @@ -456,13 +453,9 @@ e1000_check_options(struct e1000_adapter *adapter) .max = MAX_RXABSDELAY }} }; - if (num_RxAbsIntDelay > bd) { - adapter->rx_abs_int_delay = RxAbsIntDelay[bd]; - e1000_validate_option(&adapter->rx_abs_int_delay, &opt, - adapter); - } else { - adapter->rx_abs_int_delay = opt.def; - } + adapter->rx_abs_int_delay = RxAbsIntDelay[bd]; + e1000_validate_option(&adapter->rx_abs_int_delay, &opt, + adapter); } { /* Interrupt Throttling Rate */ struct e1000_option opt = { @@ -474,26 +467,44 @@ e1000_check_options(struct e1000_adapter *adapter) .max = MAX_ITR }} }; - if (num_InterruptThrottleRate > bd) { - adapter->itr = InterruptThrottleRate[bd]; - switch (adapter->itr) { - case 0: - DPRINTK(PROBE, INFO, "%s turned off\n", - opt.name); - break; - case 1: - DPRINTK(PROBE, INFO, "%s set to dynamic mode\n", - opt.name); - break; - default: - e1000_validate_option(&adapter->itr, &opt, - adapter); - break; - } - } else { - adapter->itr = opt.def; + adapter->itr = InterruptThrottleRate[bd]; + switch (adapter->itr) { + case 0: + DPRINTK(PROBE, INFO, "%s turned off\n", opt.name); + break; + case 1: + DPRINTK(PROBE, INFO, "%s set to dynamic mode\n", + opt.name); + break; + default: + e1000_validate_option(&adapter->itr, &opt, adapter); + break; } } + { /* Smart Power Down */ + struct e1000_option opt = { + .type = enable_option, + .name = "PHY Smart Power Down", + .err = "defaulting to Disabled", + .def = OPTION_DISABLED + }; + + int spd = SmartPowerDownEnable[bd]; + e1000_validate_option(&spd, &opt, adapter); + adapter->smart_power_down = spd; + } + { /* Kumeran Lock Loss Workaround */ + struct e1000_option opt = { + .type = enable_option, + .name = "Kumeran Lock Loss Workaround", + .err = "defaulting to Enabled", + .def = OPTION_ENABLED + }; + + int kmrn_lock_loss = KumeranLockLoss[bd]; + e1000_validate_option(&kmrn_lock_loss, &opt, adapter); + adapter->hw.kmrn_lock_loss_workaround_disabled = !kmrn_lock_loss; + } switch (adapter->hw.media_type) { case e1000_media_type_fiber: @@ -519,17 +530,18 @@ static void __devinit e1000_check_fiber_options(struct e1000_adapter *adapter) { int bd = adapter->bd_number; - if (num_Speed > bd) { + bd = bd > E1000_MAX_NIC ? E1000_MAX_NIC : bd; + if ((Speed[bd] != OPTION_UNSET)) { DPRINTK(PROBE, INFO, "Speed not valid for fiber adapters, " "parameter ignored\n"); } - if (num_Duplex > bd) { + if ((Duplex[bd] != OPTION_UNSET)) { DPRINTK(PROBE, INFO, "Duplex not valid for fiber adapters, " "parameter ignored\n"); } - if ((num_AutoNeg > bd) && (AutoNeg[bd] != 0x20)) { + if ((AutoNeg[bd] != OPTION_UNSET) && (AutoNeg[bd] != 0x20)) { DPRINTK(PROBE, INFO, "AutoNeg other than 1000/Full is " "not valid for fiber adapters, " "parameter ignored\n"); @@ -548,6 +560,7 @@ e1000_check_copper_options(struct e1000_adapter *adapter) { int speed, dplx, an; int bd = adapter->bd_number; + bd = bd > E1000_MAX_NIC ? E1000_MAX_NIC : bd; { /* Speed */ struct e1000_opt_list speed_list[] = {{ 0, "" }, @@ -564,12 +577,8 @@ e1000_check_copper_options(struct e1000_adapter *adapter) .p = speed_list }} }; - if (num_Speed > bd) { - speed = Speed[bd]; - e1000_validate_option(&speed, &opt, adapter); - } else { - speed = opt.def; - } + speed = Speed[bd]; + e1000_validate_option(&speed, &opt, adapter); } { /* Duplex */ struct e1000_opt_list dplx_list[] = {{ 0, "" }, @@ -591,15 +600,11 @@ e1000_check_copper_options(struct e1000_adapter *adapter) "Speed/Duplex/AutoNeg parameter ignored.\n"); return; } - if (num_Duplex > bd) { - dplx = Duplex[bd]; - e1000_validate_option(&dplx, &opt, adapter); - } else { - dplx = opt.def; - } + dplx = Duplex[bd]; + e1000_validate_option(&dplx, &opt, adapter); } - if ((num_AutoNeg > bd) && (speed != 0 || dplx != 0)) { + if (AutoNeg[bd] != OPTION_UNSET && (speed != 0 || dplx != 0)) { DPRINTK(PROBE, INFO, "AutoNeg specified along with Speed or Duplex, " "parameter ignored\n"); @@ -648,19 +653,15 @@ e1000_check_copper_options(struct e1000_adapter *adapter) .p = an_list }} }; - if (num_AutoNeg > bd) { - an = AutoNeg[bd]; - e1000_validate_option(&an, &opt, adapter); - } else { - an = opt.def; - } + an = AutoNeg[bd]; + e1000_validate_option(&an, &opt, adapter); adapter->hw.autoneg_advertised = an; } switch (speed + dplx) { case 0: adapter->hw.autoneg = adapter->fc_autoneg = 1; - if ((num_Speed > bd) && (speed != 0 || dplx != 0)) + if (Speed[bd] != OPTION_UNSET || Duplex[bd] != OPTION_UNSET) DPRINTK(PROBE, INFO, "Speed and duplex autonegotiation enabled\n"); break;