dect/linux-2.6
Archived
14
0
Fork 0
Code Releases Activity

xhci: Remove references to HC_STATE_HALT.

Browse source 
The xHCI driver doesn't ever test hcd->state for HC_STATE_HALT.  The USB
core recently stopped using it internally, so there's no point in setting
it in the driver.  We still need to set HC_STATE_RUNNING in order to make
it past the USB core's hcd->state check in register_roothub().

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This commit is contained in:
Sarah Sharp 2011-03-11 08:47:33 -08:00
parent bdfca5025a
commit ac04e6ff3e
2 changed files with 2 additions and 8 deletions
Show stats Download patch file Download diff file Expand all files Collapse all files

5
drivers/usb/host/xhci-ring.c
View file

@ -819,8 +819,7 @@ void xhci_stop_endpoint_command_watchdog(unsigned long arg)
if (ret < 0) {
/* This is bad; the host is not responding to commands and it's
* not allowing itself to be halted. At least interrupts are
* disabled, so we can set HC_STATE_HALT and notify the
* USB core. But if we call usb_hc_died(), it will attempt to
* disabled. If we call usb_hc_died(), it will attempt to
* disconnect all device drivers under this host. Those
* disconnect() methods will wait for all URBs to be unlinked,
* so we must complete them.
@ -865,7 +864,6 @@ void xhci_stop_endpoint_command_watchdog(unsigned long arg)
}
}
spin_unlock(&xhci->lock);
xhci_to_hcd(xhci)->state = HC_STATE_HALT;
xhci_dbg(xhci, "Calling usb_hc_died()\n");
usb_hc_died(xhci_to_hcd(xhci));
xhci_dbg(xhci, "xHCI host controller is dead.\n");
@ -2113,7 +2111,6 @@ irqreturn_t xhci_irq(struct usb_hcd *hcd)
xhci_warn(xhci, "WARNING: Host System Error\n");
xhci_halt(xhci);
hw_died:
xhci_to_hcd(xhci)->state = HC_STATE_HALT;
spin_unlock(&xhci->lock);
return -ESHUTDOWN;
}

5
drivers/usb/host/xhci.c
View file

@ -95,7 +95,6 @@ void xhci_quiesce(struct xhci_hcd *xhci)
* HC will complete any current and actively pipelined transactions, and
* should halt within 16 ms of the run/stop bit being cleared.
* Read HC Halted bit in the status register to see when the HC is finished.
* XXX: shouldn't we set HC_STATE_HALT here somewhere?
*/
int xhci_halt(struct xhci_hcd *xhci)
{
@ -134,7 +133,7 @@ int xhci_start(struct xhci_hcd *xhci)
}
/*
* Reset a halted HC, and set the internal HC state to HC_STATE_HALT.
* Reset a halted HC.
*
* This resets pipelines, timers, counters, state machines, etc.
* Transactions will be terminated immediately, and operational registers
@ -156,8 +155,6 @@ int xhci_reset(struct xhci_hcd *xhci)
command = xhci_readl(xhci, &xhci->op_regs->command);
command |= CMD_RESET;
xhci_writel(xhci, command, &xhci->op_regs->command);
/* XXX: Why does EHCI set this here? Shouldn't other code do this? */
xhci_to_hcd(xhci)->state = HC_STATE_HALT;
ret = handshake(xhci, &xhci->op_regs->command,
CMD_RESET, 0, 250 * 1000);