spi: remove obsolete spi-s3c24xx-gpio driver
It was equivalent to spi-gpio, and there's no longer any in-tree users of it, so get rid of it. Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Acked-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This commit is contained in:
Peter Korsgaard
Grant Likely
parent
947b35d52d
commit
45fae7def6
|
|
@ -313,16 +313,6 @@ config SPI_S3C24XX_FIQ
|
|||
no free DMA channels, or when doing transfers that required both
|
||||
TX and RX data paths.
|
||||
|
||||
config SPI_S3C24XX_GPIO
|
||||
tristate "Samsung S3C24XX series SPI by GPIO"
|
||||
depends on ARCH_S3C2410 && EXPERIMENTAL
|
||||
select SPI_BITBANG
|
||||
help
|
||||
SPI driver for Samsung S3C24XX series ARM SoCs using
|
||||
GPIO lines to provide the SPI bus. This can be used where
|
||||
the inbuilt hardware cannot provide the transfer mode, or
|
||||
where the board is using non hardware connected pins.
|
||||
|
||||
config SPI_S3C64XX
|
||||
tristate "Samsung S3C64XX series type SPI"
|
||||
depends on (ARCH_S3C64XX || ARCH_S5P64X0)
|
||||
|
|
|
|||
|
|
@ -44,7 +44,6 @@ obj-$(CONFIG_SPI_PL022) += spi-pl022.o
|
|||
obj-$(CONFIG_SPI_PPC4xx) += spi-ppc4xx.o
|
||||
obj-$(CONFIG_SPI_PXA2XX) += spi-pxa2xx.o
|
||||
obj-$(CONFIG_SPI_PXA2XX_PCI) += spi-pxa2xx-pci.o
|
||||
obj-$(CONFIG_SPI_S3C24XX_GPIO) += spi-s3c24xx-gpio.o
|
||||
obj-$(CONFIG_SPI_S3C24XX) += spi-s3c24xx-hw.o
|
||||
spi-s3c24xx-hw-y := spi-s3c24xx.o
|
||||
spi-s3c24xx-hw-$(CONFIG_SPI_S3C24XX_FIQ) += spi-s3c24xx-fiq.o
|
||||
|
|
|
|||
|
|
@ -1,200 +0,0 @@
|
|||
/*
|
||||
* Copyright (c) 2006 Ben Dooks
|
||||
* Copyright (c) 2006 Simtec Electronics
|
||||
*
|
||||
* S3C24XX GPIO based SPI driver
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 as
|
||||
* published by the Free Software Foundation.
|
||||
*
|
||||
*/
|
||||
|
||||
#include <linux/kernel.h>
|
||||
#include <linux/init.h>
|
||||
#include <linux/delay.h>
|
||||
#include <linux/spinlock.h>
|
||||
#include <linux/workqueue.h>
|
||||
#include <linux/platform_device.h>
|
||||
#include <linux/gpio.h>
|
||||
|
||||
#include <linux/spi/spi.h>
|
||||
#include <linux/spi/spi_bitbang.h>
|
||||
|
||||
#include <mach/regs-gpio.h>
|
||||
#include <mach/spi-gpio.h>
|
||||
#include <mach/hardware.h>
|
||||
|
||||
struct s3c2410_spigpio {
|
||||
struct spi_bitbang bitbang;
|
||||
|
||||
struct s3c2410_spigpio_info *info;
|
||||
struct platform_device *dev;
|
||||
};
|
||||
|
||||
static inline struct s3c2410_spigpio *spidev_to_sg(struct spi_device *spi)
|
||||
{
|
||||
return spi_master_get_devdata(spi->master);
|
||||
}
|
||||
|
||||
static inline void setsck(struct spi_device *dev, int on)
|
||||
{
|
||||
struct s3c2410_spigpio *sg = spidev_to_sg(dev);
|
||||
s3c2410_gpio_setpin(sg->info->pin_clk, on ? 1 : 0);
|
||||
}
|
||||
|
||||
static inline void setmosi(struct spi_device *dev, int on)
|
||||
{
|
||||
struct s3c2410_spigpio *sg = spidev_to_sg(dev);
|
||||
s3c2410_gpio_setpin(sg->info->pin_mosi, on ? 1 : 0);
|
||||
}
|
||||
|
||||
static inline u32 getmiso(struct spi_device *dev)
|
||||
{
|
||||
struct s3c2410_spigpio *sg = spidev_to_sg(dev);
|
||||
return s3c2410_gpio_getpin(sg->info->pin_miso) ? 1 : 0;
|
||||
}
|
||||
|
||||
#define spidelay(x) ndelay(x)
|
||||
|
||||
#include "spi-bitbang-txrx.h"
|
||||
|
||||
|
||||
static u32 s3c2410_spigpio_txrx_mode0(struct spi_device *spi,
|
||||
unsigned nsecs, u32 word, u8 bits)
|
||||
{
|
||||
return bitbang_txrx_be_cpha0(spi, nsecs, 0, 0, word, bits);
|
||||
}
|
||||
|
||||
static u32 s3c2410_spigpio_txrx_mode1(struct spi_device *spi,
|
||||
unsigned nsecs, u32 word, u8 bits)
|
||||
{
|
||||
return bitbang_txrx_be_cpha1(spi, nsecs, 0, 0, word, bits);
|
||||
}
|
||||
|
||||
static u32 s3c2410_spigpio_txrx_mode2(struct spi_device *spi,
|
||||
unsigned nsecs, u32 word, u8 bits)
|
||||
{
|
||||
return bitbang_txrx_be_cpha0(spi, nsecs, 1, 0, word, bits);
|
||||
}
|
||||
|
||||
static u32 s3c2410_spigpio_txrx_mode3(struct spi_device *spi,
|
||||
unsigned nsecs, u32 word, u8 bits)
|
||||
{
|
||||
return bitbang_txrx_be_cpha1(spi, nsecs, 1, 0, word, bits);
|
||||
}
|
||||
|
||||
|
||||
static void s3c2410_spigpio_chipselect(struct spi_device *dev, int value)
|
||||
{
|
||||
struct s3c2410_spigpio *sg = spidev_to_sg(dev);
|
||||
|
||||
if (sg->info && sg->info->chip_select)
|
||||
(sg->info->chip_select)(sg->info, value);
|
||||
}
|
||||
|
||||
static int s3c2410_spigpio_probe(struct platform_device *dev)
|
||||
{
|
||||
struct s3c2410_spigpio_info *info;
|
||||
struct spi_master *master;
|
||||
struct s3c2410_spigpio *sp;
|
||||
int ret;
|
||||
|
||||
master = spi_alloc_master(&dev->dev, sizeof(struct s3c2410_spigpio));
|
||||
if (master == NULL) {
|
||||
dev_err(&dev->dev, "failed to allocate spi master\n");
|
||||
ret = -ENOMEM;
|
||||
goto err;
|
||||
}
|
||||
|
||||
sp = spi_master_get_devdata(master);
|
||||
|
||||
platform_set_drvdata(dev, sp);
|
||||
|
||||
/* copy in the plkatform data */
|
||||
info = sp->info = dev->dev.platform_data;
|
||||
|
||||
/* setup spi bitbang adaptor */
|
||||
sp->bitbang.master = spi_master_get(master);
|
||||
sp->bitbang.master->bus_num = info->bus_num;
|
||||
sp->bitbang.master->num_chipselect = info->num_chipselect;
|
||||
sp->bitbang.chipselect = s3c2410_spigpio_chipselect;
|
||||
|
||||
sp->bitbang.txrx_word[SPI_MODE_0] = s3c2410_spigpio_txrx_mode0;
|
||||
sp->bitbang.txrx_word[SPI_MODE_1] = s3c2410_spigpio_txrx_mode1;
|
||||
sp->bitbang.txrx_word[SPI_MODE_2] = s3c2410_spigpio_txrx_mode2;
|
||||
sp->bitbang.txrx_word[SPI_MODE_3] = s3c2410_spigpio_txrx_mode3;
|
||||
|
||||
/* set state of spi pins, always assume that the clock is
|
||||
* available, but do check the MOSI and MISO. */
|
||||
s3c2410_gpio_setpin(info->pin_clk, 0);
|
||||
s3c2410_gpio_cfgpin(info->pin_clk, S3C2410_GPIO_OUTPUT);
|
||||
|
||||
if (info->pin_mosi < S3C2410_GPH10) {
|
||||
s3c2410_gpio_setpin(info->pin_mosi, 0);
|
||||
s3c2410_gpio_cfgpin(info->pin_mosi, S3C2410_GPIO_OUTPUT);
|
||||
}
|
||||
|
||||
if (info->pin_miso != S3C2410_GPA0 && info->pin_miso < S3C2410_GPH10)
|
||||
s3c2410_gpio_cfgpin(info->pin_miso, S3C2410_GPIO_INPUT);
|
||||
|
||||
ret = spi_bitbang_start(&sp->bitbang);
|
||||
if (ret)
|
||||
goto err_no_bitbang;
|
||||
|
||||
return 0;
|
||||
|
||||
err_no_bitbang:
|
||||
spi_master_put(sp->bitbang.master);
|
||||
err:
|
||||
return ret;
|
||||
|
||||
}
|
||||
|
||||
static int s3c2410_spigpio_remove(struct platform_device *dev)
|
||||
{
|
||||
struct s3c2410_spigpio *sp = platform_get_drvdata(dev);
|
||||
|
||||
spi_bitbang_stop(&sp->bitbang);
|
||||
spi_master_put(sp->bitbang.master);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
/* all gpio should be held over suspend/resume, so we should
|
||||
* not need to deal with this
|
||||
*/
|
||||
|
||||
#define s3c2410_spigpio_suspend NULL
|
||||
#define s3c2410_spigpio_resume NULL
|
||||
|
||||
/* work with hotplug and coldplug */
|
||||
MODULE_ALIAS("platform:spi_s3c24xx_gpio");
|
||||
|
||||
static struct platform_driver s3c2410_spigpio_drv = {
|
||||
.probe = s3c2410_spigpio_probe,
|
||||
.remove = s3c2410_spigpio_remove,
|
||||
.suspend = s3c2410_spigpio_suspend,
|
||||
.resume = s3c2410_spigpio_resume,
|
||||
.driver = {
|
||||
.name = "spi_s3c24xx_gpio",
|
||||
.owner = THIS_MODULE,
|
||||
},
|
||||
};
|
||||
|
||||
static int __init s3c2410_spigpio_init(void)
|
||||
{
|
||||
return platform_driver_register(&s3c2410_spigpio_drv);
|
||||
}
|
||||
|
||||
static void __exit s3c2410_spigpio_exit(void)
|
||||
{
|
||||
platform_driver_unregister(&s3c2410_spigpio_drv);
|
||||
}
|
||||
|
||||
module_init(s3c2410_spigpio_init);
|
||||
module_exit(s3c2410_spigpio_exit);
|
||||
|
||||
MODULE_DESCRIPTION("S3C24XX SPI Driver");
|
||||
MODULE_AUTHOR("Ben Dooks, <ben@simtec.co.uk>");
|
||||
MODULE_LICENSE("GPL");
|
||||
Reference in New Issue