diff --git a/arch/powerpc/platforms/chrp/gg2.h b/arch/powerpc/platforms/chrp/gg2.h new file mode 100644 index 00000000000..341ae55b99f --- /dev/null +++ b/arch/powerpc/platforms/chrp/gg2.h @@ -0,0 +1,61 @@ +/* + * include/asm-ppc/gg2.h -- VLSI VAS96011/12 `Golden Gate 2' register definitions + * + * Copyright (C) 1997 Geert Uytterhoeven + * + * This file is based on the following documentation: + * + * The VAS96011/12 Chipset, Data Book, Edition 1.0 + * VLSI Technology, Inc. + * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file COPYING in the main directory of this archive + * for more details. + */ + +#ifndef _ASMPPC_GG2_H +#define _ASMPPC_GG2_H + + /* + * Memory Map (CHRP mode) + */ + +#define GG2_PCI_MEM_BASE 0xc0000000 /* Peripheral memory space */ +#define GG2_ISA_MEM_BASE 0xf7000000 /* Peripheral memory alias */ +#define GG2_ISA_IO_BASE 0xf8000000 /* Peripheral I/O space */ +#define GG2_PCI_CONFIG_BASE 0xfec00000 /* PCI configuration space */ +#define GG2_INT_ACK_SPECIAL 0xfec80000 /* Interrupt acknowledge and */ + /* special PCI cycles */ +#define GG2_ROM_BASE0 0xff000000 /* ROM bank 0 */ +#define GG2_ROM_BASE1 0xff800000 /* ROM bank 1 */ + + + /* + * GG2 specific PCI Registers + */ + +extern void __iomem *gg2_pci_config_base; /* kernel virtual address */ + +#define GG2_PCI_BUSNO 0x40 /* Bus number */ +#define GG2_PCI_SUBBUSNO 0x41 /* Subordinate bus number */ +#define GG2_PCI_DISCCTR 0x42 /* Disconnect counter */ +#define GG2_PCI_PPC_CTRL 0x50 /* PowerPC interface control register */ +#define GG2_PCI_ADDR_MAP 0x5c /* Address map */ +#define GG2_PCI_PCI_CTRL 0x60 /* PCI interface control register */ +#define GG2_PCI_ROM_CTRL 0x70 /* ROM interface control register */ +#define GG2_PCI_ROM_TIME 0x74 /* ROM timing */ +#define GG2_PCI_CC_CTRL 0x80 /* Cache controller control register */ +#define GG2_PCI_DRAM_BANK0 0x90 /* Control register for DRAM bank #0 */ +#define GG2_PCI_DRAM_BANK1 0x94 /* Control register for DRAM bank #1 */ +#define GG2_PCI_DRAM_BANK2 0x98 /* Control register for DRAM bank #2 */ +#define GG2_PCI_DRAM_BANK3 0x9c /* Control register for DRAM bank #3 */ +#define GG2_PCI_DRAM_BANK4 0xa0 /* Control register for DRAM bank #4 */ +#define GG2_PCI_DRAM_BANK5 0xa4 /* Control register for DRAM bank #5 */ +#define GG2_PCI_DRAM_TIME0 0xb0 /* Timing parameters set #0 */ +#define GG2_PCI_DRAM_TIME1 0xb4 /* Timing parameters set #1 */ +#define GG2_PCI_DRAM_CTRL 0xc0 /* DRAM control */ +#define GG2_PCI_ERR_CTRL 0xd0 /* Error control register */ +#define GG2_PCI_ERR_STATUS 0xd4 /* Error status register */ + /* Cleared when read */ + +#endif /* _ASMPPC_GG2_H */ diff --git a/arch/powerpc/platforms/chrp/pci.c b/arch/powerpc/platforms/chrp/pci.c index 974952ed15c..e43465d34d2 100644 --- a/arch/powerpc/platforms/chrp/pci.c +++ b/arch/powerpc/platforms/chrp/pci.c @@ -13,7 +13,6 @@ #include #include #include -#include #include #include #include @@ -21,6 +20,7 @@ #include #include "chrp.h" +#include "gg2.h" /* LongTrail */ void __iomem *gg2_pci_config_base; diff --git a/arch/powerpc/platforms/chrp/setup.c b/arch/powerpc/platforms/chrp/setup.c index dde5ef4dde3..96498ad7b94 100644 --- a/arch/powerpc/platforms/chrp/setup.c +++ b/arch/powerpc/platforms/chrp/setup.c @@ -37,7 +37,6 @@ #include #include #include -#include #include #include #include @@ -51,6 +50,7 @@ #include #include "chrp.h" +#include "gg2.h" void rtas_indicator_progress(char *, unsigned short); diff --git a/arch/powerpc/platforms/embedded6xx/linkstation.c b/arch/powerpc/platforms/embedded6xx/linkstation.c index 8c60e0207d0..61ca02c2d64 100644 --- a/arch/powerpc/platforms/embedded6xx/linkstation.c +++ b/arch/powerpc/platforms/embedded6xx/linkstation.c @@ -18,9 +18,10 @@ #include #include #include -#include #include +#include "mpc10x.h" + static struct mtd_partition linkstation_physmap_partitions[] = { { .name = "mtd_firmimg", diff --git a/arch/powerpc/platforms/embedded6xx/ls_uart.c b/arch/powerpc/platforms/embedded6xx/ls_uart.c index f7a4def5eff..0d9f1500a67 100644 --- a/arch/powerpc/platforms/embedded6xx/ls_uart.c +++ b/arch/powerpc/platforms/embedded6xx/ls_uart.c @@ -4,10 +4,11 @@ #include #include #include -#include #include #include +#include "mpc10x.h" + static void __iomem *avr_addr; static unsigned long avr_clock; diff --git a/arch/powerpc/platforms/embedded6xx/mpc10x.h b/arch/powerpc/platforms/embedded6xx/mpc10x.h new file mode 100644 index 00000000000..b30a6a3b5bd --- /dev/null +++ b/arch/powerpc/platforms/embedded6xx/mpc10x.h @@ -0,0 +1,180 @@ +/* + * Common routines for the Motorola SPS MPC106/8240/107 Host bridge/Mem + * ctlr/EPIC/etc. + * + * Author: Mark A. Greer + * mgreer@mvista.com + * + * 2001 (c) MontaVista, Software, Inc. This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + */ +#ifndef __PPC_KERNEL_MPC10X_H +#define __PPC_KERNEL_MPC10X_H + +#include +#include + +/* + * The values here don't completely map everything but should work in most + * cases. + * + * MAP A (PReP Map) + * Processor: 0x80000000 - 0x807fffff -> PCI I/O: 0x00000000 - 0x007fffff + * Processor: 0xc0000000 - 0xdfffffff -> PCI MEM: 0x00000000 - 0x1fffffff + * PCI MEM: 0x80000000 -> Processor System Memory: 0x00000000 + * EUMB mapped to: ioremap_base - 0x00100000 (ioremap_base - 1 MB) + * + * MAP B (CHRP Map) + * Processor: 0xfe000000 - 0xfebfffff -> PCI I/O: 0x00000000 - 0x00bfffff + * Processor: 0x80000000 - 0xbfffffff -> PCI MEM: 0x80000000 - 0xbfffffff + * PCI MEM: 0x00000000 -> Processor System Memory: 0x00000000 + * EUMB mapped to: ioremap_base - 0x00100000 (ioremap_base - 1 MB) + */ + +/* + * Define the vendor/device IDs for the various bridges--should be added to + * + */ +#define MPC10X_BRIDGE_106 ((PCI_DEVICE_ID_MOTOROLA_MPC106 << 16) | \ + PCI_VENDOR_ID_MOTOROLA) +#define MPC10X_BRIDGE_8240 ((0x0003 << 16) | PCI_VENDOR_ID_MOTOROLA) +#define MPC10X_BRIDGE_107 ((0x0004 << 16) | PCI_VENDOR_ID_MOTOROLA) +#define MPC10X_BRIDGE_8245 ((0x0006 << 16) | PCI_VENDOR_ID_MOTOROLA) + +/* Define the type of map to use */ +#define MPC10X_MEM_MAP_A 1 +#define MPC10X_MEM_MAP_B 2 + +/* Map A (PReP Map) Defines */ +#define MPC10X_MAPA_CNFG_ADDR 0x80000cf8 +#define MPC10X_MAPA_CNFG_DATA 0x80000cfc + +#define MPC10X_MAPA_ISA_IO_BASE 0x80000000 +#define MPC10X_MAPA_ISA_MEM_BASE 0xc0000000 +#define MPC10X_MAPA_DRAM_OFFSET 0x80000000 + +#define MPC10X_MAPA_PCI_INTACK_ADDR 0xbffffff0 +#define MPC10X_MAPA_PCI_IO_START 0x00000000 +#define MPC10X_MAPA_PCI_IO_END (0x00800000 - 1) +#define MPC10X_MAPA_PCI_MEM_START 0x00000000 +#define MPC10X_MAPA_PCI_MEM_END (0x20000000 - 1) + +#define MPC10X_MAPA_PCI_MEM_OFFSET (MPC10X_MAPA_ISA_MEM_BASE - \ + MPC10X_MAPA_PCI_MEM_START) + +/* Map B (CHRP Map) Defines */ +#define MPC10X_MAPB_CNFG_ADDR 0xfec00000 +#define MPC10X_MAPB_CNFG_DATA 0xfee00000 + +#define MPC10X_MAPB_ISA_IO_BASE 0xfe000000 +#define MPC10X_MAPB_ISA_MEM_BASE 0x80000000 +#define MPC10X_MAPB_DRAM_OFFSET 0x00000000 + +#define MPC10X_MAPB_PCI_INTACK_ADDR 0xfef00000 +#define MPC10X_MAPB_PCI_IO_START 0x00000000 +#define MPC10X_MAPB_PCI_IO_END (0x00c00000 - 1) +#define MPC10X_MAPB_PCI_MEM_START 0x80000000 +#define MPC10X_MAPB_PCI_MEM_END (0xc0000000 - 1) + +#define MPC10X_MAPB_PCI_MEM_OFFSET (MPC10X_MAPB_ISA_MEM_BASE - \ + MPC10X_MAPB_PCI_MEM_START) + +/* Set hose members to values appropriate for the mem map used */ +#define MPC10X_SETUP_HOSE(hose, map) { \ + (hose)->pci_mem_offset = MPC10X_MAP##map##_PCI_MEM_OFFSET; \ + (hose)->io_space.start = MPC10X_MAP##map##_PCI_IO_START; \ + (hose)->io_space.end = MPC10X_MAP##map##_PCI_IO_END; \ + (hose)->mem_space.start = MPC10X_MAP##map##_PCI_MEM_START; \ + (hose)->mem_space.end = MPC10X_MAP##map##_PCI_MEM_END; \ + (hose)->io_base_virt = (void *)MPC10X_MAP##map##_ISA_IO_BASE; \ +} + + +/* Miscellaneous Configuration register offsets */ +#define MPC10X_CFG_PIR_REG 0x09 +#define MPC10X_CFG_PIR_HOST_BRIDGE 0x00 +#define MPC10X_CFG_PIR_AGENT 0x01 + +#define MPC10X_CFG_EUMBBAR 0x78 + +#define MPC10X_CFG_PICR1_REG 0xa8 +#define MPC10X_CFG_PICR1_ADDR_MAP_MASK 0x00010000 +#define MPC10X_CFG_PICR1_ADDR_MAP_A 0x00010000 +#define MPC10X_CFG_PICR1_ADDR_MAP_B 0x00000000 +#define MPC10X_CFG_PICR1_SPEC_PCI_RD 0x00000004 +#define MPC10X_CFG_PICR1_ST_GATH_EN 0x00000040 + +#define MPC10X_CFG_PICR2_REG 0xac +#define MPC10X_CFG_PICR2_COPYBACK_OPT 0x00000001 + +#define MPC10X_CFG_MAPB_OPTIONS_REG 0xe0 +#define MPC10X_CFG_MAPB_OPTIONS_CFAE 0x80 /* CPU_FD_ALIAS_EN */ +#define MPC10X_CFG_MAPB_OPTIONS_PFAE 0x40 /* PCI_FD_ALIAS_EN */ +#define MPC10X_CFG_MAPB_OPTIONS_DR 0x20 /* DLL_RESET */ +#define MPC10X_CFG_MAPB_OPTIONS_PCICH 0x08 /* PCI_COMPATIBILITY_HOLE */ +#define MPC10X_CFG_MAPB_OPTIONS_PROCCH 0x04 /* PROC_COMPATIBILITY_HOLE */ + +/* Define offsets for the memory controller registers in the config space */ +#define MPC10X_MCTLR_MEM_START_1 0x80 /* Banks 0-3 */ +#define MPC10X_MCTLR_MEM_START_2 0x84 /* Banks 4-7 */ +#define MPC10X_MCTLR_EXT_MEM_START_1 0x88 /* Banks 0-3 */ +#define MPC10X_MCTLR_EXT_MEM_START_2 0x8c /* Banks 4-7 */ + +#define MPC10X_MCTLR_MEM_END_1 0x90 /* Banks 0-3 */ +#define MPC10X_MCTLR_MEM_END_2 0x94 /* Banks 4-7 */ +#define MPC10X_MCTLR_EXT_MEM_END_1 0x98 /* Banks 0-3 */ +#define MPC10X_MCTLR_EXT_MEM_END_2 0x9c /* Banks 4-7 */ + +#define MPC10X_MCTLR_MEM_BANK_ENABLES 0xa0 + +/* Define some offset in the EUMB */ +#define MPC10X_EUMB_SIZE 0x00100000 /* Total EUMB size (1MB) */ + +#define MPC10X_EUMB_MU_OFFSET 0x00000000 /* Msg Unit reg offset */ +#define MPC10X_EUMB_MU_SIZE 0x00001000 /* Msg Unit reg size */ +#define MPC10X_EUMB_DMA_OFFSET 0x00001000 /* DMA Unit reg offset */ +#define MPC10X_EUMB_DMA_SIZE 0x00001000 /* DMA Unit reg size */ +#define MPC10X_EUMB_ATU_OFFSET 0x00002000 /* Addr xlate reg offset */ +#define MPC10X_EUMB_ATU_SIZE 0x00001000 /* Addr xlate reg size */ +#define MPC10X_EUMB_I2C_OFFSET 0x00003000 /* I2C Unit reg offset */ +#define MPC10X_EUMB_I2C_SIZE 0x00001000 /* I2C Unit reg size */ +#define MPC10X_EUMB_DUART_OFFSET 0x00004000 /* DUART Unit reg offset (8245) */ +#define MPC10X_EUMB_DUART_SIZE 0x00001000 /* DUART Unit reg size (8245) */ +#define MPC10X_EUMB_EPIC_OFFSET 0x00040000 /* EPIC offset in EUMB */ +#define MPC10X_EUMB_EPIC_SIZE 0x00030000 /* EPIC size */ +#define MPC10X_EUMB_PM_OFFSET 0x000fe000 /* Performance Monitor reg offset (8245) */ +#define MPC10X_EUMB_PM_SIZE 0x00001000 /* Performance Monitor reg size (8245) */ +#define MPC10X_EUMB_WP_OFFSET 0x000ff000 /* Data path diagnostic, watchpoint reg offset */ +#define MPC10X_EUMB_WP_SIZE 0x00001000 /* Data path diagnostic, watchpoint reg size */ + +/* + * Define some recommended places to put the EUMB regs. + * For both maps, recommend putting the EUMB from 0xeff00000 to 0xefffffff. + */ +extern unsigned long ioremap_base; +#define MPC10X_MAPA_EUMB_BASE (ioremap_base - MPC10X_EUMB_SIZE) +#define MPC10X_MAPB_EUMB_BASE MPC10X_MAPA_EUMB_BASE + +enum ppc_sys_devices { + MPC10X_IIC1, + MPC10X_DMA0, + MPC10X_DMA1, + MPC10X_UART0, + MPC10X_UART1, + NUM_PPC_SYS_DEVS, +}; + +int mpc10x_bridge_init(struct pci_controller *hose, + uint current_map, + uint new_map, + uint phys_eumb_base); +unsigned long mpc10x_get_mem_size(uint mem_map); +int mpc10x_enable_store_gathering(struct pci_controller *hose); +int mpc10x_disable_store_gathering(struct pci_controller *hose); + +/* For MPC107 boards that use the built-in openpic */ +void mpc10x_set_openpic(void); + +#endif /* __PPC_KERNEL_MPC10X_H */ diff --git a/drivers/macintosh/ans-lcd.c b/drivers/macintosh/ans-lcd.c index e54c4d9f636..73c50bc0209 100644 --- a/drivers/macintosh/ans-lcd.c +++ b/drivers/macintosh/ans-lcd.c @@ -14,9 +14,10 @@ #include #include #include -#include #include +#include "ans-lcd.h" + #define ANSLCD_ADDR 0xf301c000 #define ANSLCD_CTRL_IX 0x00 #define ANSLCD_DATA_IX 0x10 diff --git a/include/asm-ppc/ans-lcd.h b/drivers/macintosh/ans-lcd.h similarity index 100% rename from include/asm-ppc/ans-lcd.h rename to drivers/macintosh/ans-lcd.h diff --git a/include/asm-powerpc/8xx_immap.h b/include/asm-powerpc/8xx_immap.h new file mode 100644 index 00000000000..1311cefdfd3 --- /dev/null +++ b/include/asm-powerpc/8xx_immap.h @@ -0,0 +1,564 @@ +/* + * MPC8xx Internal Memory Map + * Copyright (c) 1997 Dan Malek (dmalek@jlc.net) + * + * The I/O on the MPC860 is comprised of blocks of special registers + * and the dual port ram for the Communication Processor Module. + * Within this space are functional units such as the SIU, memory + * controller, system timers, and other control functions. It is + * a combination that I found difficult to separate into logical + * functional files.....but anyone else is welcome to try. -- Dan + */ +#ifdef __KERNEL__ +#ifndef __IMMAP_8XX__ +#define __IMMAP_8XX__ + +/* System configuration registers. +*/ +typedef struct sys_conf { + uint sc_siumcr; + uint sc_sypcr; + uint sc_swt; + char res1[2]; + ushort sc_swsr; + uint sc_sipend; + uint sc_simask; + uint sc_siel; + uint sc_sivec; + uint sc_tesr; + char res2[0xc]; + uint sc_sdcr; + char res3[0x4c]; +} sysconf8xx_t; + +/* PCMCIA configuration registers. +*/ +typedef struct pcmcia_conf { + uint pcmc_pbr0; + uint pcmc_por0; + uint pcmc_pbr1; + uint pcmc_por1; + uint pcmc_pbr2; + uint pcmc_por2; + uint pcmc_pbr3; + uint pcmc_por3; + uint pcmc_pbr4; + uint pcmc_por4; + uint pcmc_pbr5; + uint pcmc_por5; + uint pcmc_pbr6; + uint pcmc_por6; + uint pcmc_pbr7; + uint pcmc_por7; + char res1[0x20]; + uint pcmc_pgcra; + uint pcmc_pgcrb; + uint pcmc_pscr; + char res2[4]; + uint pcmc_pipr; + char res3[4]; + uint pcmc_per; + char res4[4]; +} pcmconf8xx_t; + +/* Memory controller registers. +*/ +typedef struct mem_ctlr { + uint memc_br0; + uint memc_or0; + uint memc_br1; + uint memc_or1; + uint memc_br2; + uint memc_or2; + uint memc_br3; + uint memc_or3; + uint memc_br4; + uint memc_or4; + uint memc_br5; + uint memc_or5; + uint memc_br6; + uint memc_or6; + uint memc_br7; + uint memc_or7; + char res1[0x24]; + uint memc_mar; + uint memc_mcr; + char res2[4]; + uint memc_mamr; + uint memc_mbmr; + ushort memc_mstat; + ushort memc_mptpr; + uint memc_mdr; + char res3[0x80]; +} memctl8xx_t; + +/*----------------------------------------------------------------------- + * BR - Memory Controler: Base Register 16-9 + */ +#define BR_BA_MSK 0xffff8000 /* Base Address Mask */ +#define BR_AT_MSK 0x00007000 /* Address Type Mask */ +#define BR_PS_MSK 0x00000c00 /* Port Size Mask */ +#define BR_PS_32 0x00000000 /* 32 bit port size */ +#define BR_PS_16 0x00000800 /* 16 bit port size */ +#define BR_PS_8 0x00000400 /* 8 bit port size */ +#define BR_PARE 0x00000200 /* Parity Enable */ +#define BR_WP 0x00000100 /* Write Protect */ +#define BR_MS_MSK 0x000000c0 /* Machine Select Mask */ +#define BR_MS_GPCM 0x00000000 /* G.P.C.M. Machine Select */ +#define BR_MS_UPMA 0x00000080 /* U.P.M.A Machine Select */ +#define BR_MS_UPMB 0x000000c0 /* U.P.M.B Machine Select */ +#define BR_V 0x00000001 /* Bank Valid */ + +/*----------------------------------------------------------------------- + * OR - Memory Controler: Option Register 16-11 + */ +#define OR_AM_MSK 0xffff8000 /* Address Mask Mask */ +#define OR_ATM_MSK 0x00007000 /* Address Type Mask Mask */ +#define OR_CSNT_SAM 0x00000800 /* Chip Select Negation Time/ Start */ + /* Address Multiplex */ +#define OR_ACS_MSK 0x00000600 /* Address to Chip Select Setup mask */ +#define OR_ACS_DIV1 0x00000000 /* CS is output at the same time */ +#define OR_ACS_DIV4 0x00000400 /* CS is output 1/4 a clock later */ +#define OR_ACS_DIV2 0x00000600 /* CS is output 1/2 a clock later */ +#define OR_G5LA 0x00000400 /* Output #GPL5 on #GPL_A5 */ +#define OR_G5LS 0x00000200 /* Drive #GPL high on falling edge of...*/ +#define OR_BI 0x00000100 /* Burst inhibit */ +#define OR_SCY_MSK 0x000000f0 /* Cycle Lenght in Clocks */ +#define OR_SCY_0_CLK 0x00000000 /* 0 clock cycles wait states */ +#define OR_SCY_1_CLK 0x00000010 /* 1 clock cycles wait states */ +#define OR_SCY_2_CLK 0x00000020 /* 2 clock cycles wait states */ +#define OR_SCY_3_CLK 0x00000030 /* 3 clock cycles wait states */ +#define OR_SCY_4_CLK 0x00000040 /* 4 clock cycles wait states */ +#define OR_SCY_5_CLK 0x00000050 /* 5 clock cycles wait states */ +#define OR_SCY_6_CLK 0x00000060 /* 6 clock cycles wait states */ +#define OR_SCY_7_CLK 0x00000070 /* 7 clock cycles wait states */ +#define OR_SCY_8_CLK 0x00000080 /* 8 clock cycles wait states */ +#define OR_SCY_9_CLK 0x00000090 /* 9 clock cycles wait states */ +#define OR_SCY_10_CLK 0x000000a0 /* 10 clock cycles wait states */ +#define OR_SCY_11_CLK 0x000000b0 /* 11 clock cycles wait states */ +#define OR_SCY_12_CLK 0x000000c0 /* 12 clock cycles wait states */ +#define OR_SCY_13_CLK 0x000000d0 /* 13 clock cycles wait states */ +#define OR_SCY_14_CLK 0x000000e0 /* 14 clock cycles wait states */ +#define OR_SCY_15_CLK 0x000000f0 /* 15 clock cycles wait states */ +#define OR_SETA 0x00000008 /* External Transfer Acknowledge */ +#define OR_TRLX 0x00000004 /* Timing Relaxed */ +#define OR_EHTR 0x00000002 /* Extended Hold Time on Read */ + +/* System Integration Timers. +*/ +typedef struct sys_int_timers { + ushort sit_tbscr; + char res0[0x02]; + uint sit_tbreff0; + uint sit_tbreff1; + char res1[0x14]; + ushort sit_rtcsc; + char res2[0x02]; + uint sit_rtc; + uint sit_rtsec; + uint sit_rtcal; + char res3[0x10]; + ushort sit_piscr; + char res4[2]; + uint sit_pitc; + uint sit_pitr; + char res5[0x34]; +} sit8xx_t; + +#define TBSCR_TBIRQ_MASK ((ushort)0xff00) +#define TBSCR_REFA ((ushort)0x0080) +#define TBSCR_REFB ((ushort)0x0040) +#define TBSCR_REFAE ((ushort)0x0008) +#define TBSCR_REFBE ((ushort)0x0004) +#define TBSCR_TBF ((ushort)0x0002) +#define TBSCR_TBE ((ushort)0x0001) + +#define RTCSC_RTCIRQ_MASK ((ushort)0xff00) +#define RTCSC_SEC ((ushort)0x0080) +#define RTCSC_ALR ((ushort)0x0040) +#define RTCSC_38K ((ushort)0x0010) +#define RTCSC_SIE ((ushort)0x0008) +#define RTCSC_ALE ((ushort)0x0004) +#define RTCSC_RTF ((ushort)0x0002) +#define RTCSC_RTE ((ushort)0x0001) + +#define PISCR_PIRQ_MASK ((ushort)0xff00) +#define PISCR_PS ((ushort)0x0080) +#define PISCR_PIE ((ushort)0x0004) +#define PISCR_PTF ((ushort)0x0002) +#define PISCR_PTE ((ushort)0x0001) + +/* Clocks and Reset. +*/ +typedef struct clk_and_reset { + uint car_sccr; + uint car_plprcr; + uint car_rsr; + char res[0x74]; /* Reserved area */ +} car8xx_t; + +/* System Integration Timers keys. +*/ +typedef struct sitk { + uint sitk_tbscrk; + uint sitk_tbreff0k; + uint sitk_tbreff1k; + uint sitk_tbk; + char res1[0x10]; + uint sitk_rtcsck; + uint sitk_rtck; + uint sitk_rtseck; + uint sitk_rtcalk; + char res2[0x10]; + uint sitk_piscrk; + uint sitk_pitck; + char res3[0x38]; +} sitk8xx_t; + +/* Clocks and reset keys. +*/ +typedef struct cark { + uint cark_sccrk; + uint cark_plprcrk; + uint cark_rsrk; + char res[0x474]; +} cark8xx_t; + +/* The key to unlock registers maintained by keep-alive power. +*/ +#define KAPWR_KEY ((unsigned int)0x55ccaa33) + +/* Video interface. MPC823 Only. +*/ +typedef struct vid823 { + ushort vid_vccr; + ushort res1; + u_char vid_vsr; + u_char res2; + u_char vid_vcmr; + u_char res3; + uint vid_vbcb; + uint res4; + uint vid_vfcr0; + uint vid_vfaa0; + uint vid_vfba0; + uint vid_vfcr1; + uint vid_vfaa1; + uint vid_vfba1; + u_char res5[0x18]; +} vid823_t; + +/* LCD interface. 823 Only. +*/ +typedef struct lcd { + uint lcd_lccr; + uint lcd_lchcr; + uint lcd_lcvcr; + char res1[4]; + uint lcd_lcfaa; + uint lcd_lcfba; + char lcd_lcsr; + char res2[0x7]; +} lcd823_t; + +/* I2C +*/ +typedef struct i2c { + u_char i2c_i2mod; + char res1[3]; + u_char i2c_i2add; + char res2[3]; + u_char i2c_i2brg; + char res3[3]; + u_char i2c_i2com; + char res4[3]; + u_char i2c_i2cer; + char res5[3]; + u_char i2c_i2cmr; + char res6[0x8b]; +} i2c8xx_t; + +/* DMA control/status registers. +*/ +typedef struct sdma_csr { + char res1[4]; + uint sdma_sdar; + u_char sdma_sdsr; + char res3[3]; + u_char sdma_sdmr; + char res4[3]; + u_char sdma_idsr1; + char res5[3]; + u_char sdma_idmr1; + char res6[3]; + u_char sdma_idsr2; + char res7[3]; + u_char sdma_idmr2; + char res8[0x13]; +} sdma8xx_t; + +/* Communication Processor Module Interrupt Controller. +*/ +typedef struct cpm_ic { + ushort cpic_civr; + char res[0xe]; + uint cpic_cicr; + uint cpic_cipr; + uint cpic_cimr; + uint cpic_cisr; +} cpic8xx_t; + +/* Input/Output Port control/status registers. +*/ +typedef struct io_port { + ushort iop_padir; + ushort iop_papar; + ushort iop_paodr; + ushort iop_padat; + char res1[8]; + ushort iop_pcdir; + ushort iop_pcpar; + ushort iop_pcso; + ushort iop_pcdat; + ushort iop_pcint; + char res2[6]; + ushort iop_pddir; + ushort iop_pdpar; + char res3[2]; + ushort iop_pddat; + uint utmode; + char res4[4]; +} iop8xx_t; + +/* Communication Processor Module Timers +*/ +typedef struct cpm_timers { + ushort cpmt_tgcr; + char res1[0xe]; + ushort cpmt_tmr1; + ushort cpmt_tmr2; + ushort cpmt_trr1; + ushort cpmt_trr2; + ushort cpmt_tcr1; + ushort cpmt_tcr2; + ushort cpmt_tcn1; + ushort cpmt_tcn2; + ushort cpmt_tmr3; + ushort cpmt_tmr4; + ushort cpmt_trr3; + ushort cpmt_trr4; + ushort cpmt_tcr3; + ushort cpmt_tcr4; + ushort cpmt_tcn3; + ushort cpmt_tcn4; + ushort cpmt_ter1; + ushort cpmt_ter2; + ushort cpmt_ter3; + ushort cpmt_ter4; + char res2[8]; +} cpmtimer8xx_t; + +/* Finally, the Communication Processor stuff..... +*/ +typedef struct scc { /* Serial communication channels */ + uint scc_gsmrl; + uint scc_gsmrh; + ushort scc_psmr; + char res1[2]; + ushort scc_todr; + ushort scc_dsr; + ushort scc_scce; + char res2[2]; + ushort scc_sccm; + char res3; + u_char scc_sccs; + char res4[8]; +} scc_t; + +typedef struct smc { /* Serial management channels */ + char res1[2]; + ushort smc_smcmr; + char res2[2]; + u_char smc_smce; + char res3[3]; + u_char smc_smcm; + char res4[5]; +} smc_t; + +/* MPC860T Fast Ethernet Controller. It isn't part of the CPM, but + * it fits within the address space. + */ + +typedef struct fec { + uint fec_addr_low; /* lower 32 bits of station address */ + ushort fec_addr_high; /* upper 16 bits of station address */ + ushort res1; /* reserved */ + uint fec_hash_table_high; /* upper 32-bits of hash table */ + uint fec_hash_table_low; /* lower 32-bits of hash table */ + uint fec_r_des_start; /* beginning of Rx descriptor ring */ + uint fec_x_des_start; /* beginning of Tx descriptor ring */ + uint fec_r_buff_size; /* Rx buffer size */ + uint res2[9]; /* reserved */ + uint fec_ecntrl; /* ethernet control register */ + uint fec_ievent; /* interrupt event register */ + uint fec_imask; /* interrupt mask register */ + uint fec_ivec; /* interrupt level and vector status */ + uint fec_r_des_active; /* Rx ring updated flag */ + uint fec_x_des_active; /* Tx ring updated flag */ + uint res3[10]; /* reserved */ + uint fec_mii_data; /* MII data register */ + uint fec_mii_speed; /* MII speed control register */ + uint res4[17]; /* reserved */ + uint fec_r_bound; /* end of RAM (read-only) */ + uint fec_r_fstart; /* Rx FIFO start address */ + uint res5[6]; /* reserved */ + uint fec_x_fstart; /* Tx FIFO start address */ + uint res6[17]; /* reserved */ + uint fec_fun_code; /* fec SDMA function code */ + uint res7[3]; /* reserved */ + uint fec_r_cntrl; /* Rx control register */ + uint fec_r_hash; /* Rx hash register */ + uint res8[14]; /* reserved */ + uint fec_x_cntrl; /* Tx control register */ + uint res9[0x1e]; /* reserved */ +} fec_t; + +/* The FEC and LCD color map share the same address space.... + * I guess we will never see an 823T :-). + */ +union fec_lcd { + fec_t fl_un_fec; + u_char fl_un_cmap[0x200]; +}; + +typedef struct comm_proc { + /* General control and status registers. + */ + ushort cp_cpcr; + u_char res1[2]; + ushort cp_rccr; + u_char res2; + u_char cp_rmds; + u_char res3[4]; + ushort cp_cpmcr1; + ushort cp_cpmcr2; + ushort cp_cpmcr3; + ushort cp_cpmcr4; + u_char res4[2]; + ushort cp_rter; + u_char res5[2]; + ushort cp_rtmr; + u_char res6[0x14]; + + /* Baud rate generators. + */ + uint cp_brgc1; + uint cp_brgc2; + uint cp_brgc3; + uint cp_brgc4; + + /* Serial Communication Channels. + */ + scc_t cp_scc[4]; + + /* Serial Management Channels. + */ + smc_t cp_smc[2]; + + /* Serial Peripheral Interface. + */ + ushort cp_spmode; + u_char res7[4]; + u_char cp_spie; + u_char res8[3]; + u_char cp_spim; + u_char res9[2]; + u_char cp_spcom; + u_char res10[2]; + + /* Parallel Interface Port. + */ + u_char res11[2]; + ushort cp_pipc; + u_char res12[2]; + ushort cp_ptpr; + uint cp_pbdir; + uint cp_pbpar; + u_char res13[2]; + ushort cp_pbodr; + uint cp_pbdat; + + /* Port E - MPC87x/88x only. + */ + uint cp_pedir; + uint cp_pepar; + uint cp_peso; + uint cp_peodr; + uint cp_pedat; + + /* Communications Processor Timing Register - + Contains RMII Timing for the FECs on MPC87x/88x only. + */ + uint cp_cptr; + + /* Serial Interface and Time Slot Assignment. + */ + uint cp_simode; + u_char cp_sigmr; + u_char res15; + u_char cp_sistr; + u_char cp_sicmr; + u_char res16[4]; + uint cp_sicr; + uint cp_sirp; + u_char res17[0xc]; + + /* 256 bytes of MPC823 video controller RAM array. + */ + u_char cp_vcram[0x100]; + u_char cp_siram[0x200]; + + /* The fast ethernet controller is not really part of the CPM, + * but it resides in the address space. + * The LCD color map is also here. + */ + union fec_lcd fl_un; +#define cp_fec fl_un.fl_un_fec +#define lcd_cmap fl_un.fl_un_cmap + char res18[0xE00]; + + /* The DUET family has a second FEC here */ + fec_t cp_fec2; +#define cp_fec1 cp_fec /* consistency macro */ + + /* Dual Ported RAM follows. + * There are many different formats for this memory area + * depending upon the devices used and options chosen. + * Some processors don't have all of it populated. + */ + u_char cp_dpmem[0x1C00]; /* BD / Data / ucode */ + u_char cp_dparam[0x400]; /* Parameter RAM */ +} cpm8xx_t; + +/* Internal memory map. +*/ +typedef struct immap { + sysconf8xx_t im_siu_conf; /* SIU Configuration */ + pcmconf8xx_t im_pcmcia; /* PCMCIA Configuration */ + memctl8xx_t im_memctl; /* Memory Controller */ + sit8xx_t im_sit; /* System integration timers */ + car8xx_t im_clkrst; /* Clocks and reset */ + sitk8xx_t im_sitk; /* Sys int timer keys */ + cark8xx_t im_clkrstk; /* Clocks and reset keys */ + vid823_t im_vid; /* Video (823 only) */ + lcd823_t im_lcd; /* LCD (823 only) */ + i2c8xx_t im_i2c; /* I2C control/status */ + sdma8xx_t im_sdma; /* SDMA control/status */ + cpic8xx_t im_cpic; /* CPM Interrupt Controller */ + iop8xx_t im_ioport; /* IO Port control/status */ + cpmtimer8xx_t im_cpmtimer; /* CPM timers */ + cpm8xx_t im_cpm; /* Communication processor */ +} immap_t; + +#endif /* __IMMAP_8XX__ */ +#endif /* __KERNEL__ */ diff --git a/include/asm-powerpc/commproc.h b/include/asm-powerpc/commproc.h new file mode 100644 index 00000000000..397248705e0 --- /dev/null +++ b/include/asm-powerpc/commproc.h @@ -0,0 +1,692 @@ +/* + * MPC8xx Communication Processor Module. + * Copyright (c) 1997 Dan Malek (dmalek@jlc.net) + * + * This file contains structures and information for the communication + * processor channels. Some CPM control and status is available + * throught the MPC8xx internal memory map. See immap.h for details. + * This file only contains what I need for the moment, not the total + * CPM capabilities. I (or someone else) will add definitions as they + * are needed. -- Dan + * + * On the MBX board, EPPC-Bug loads CPM microcode into the first 512 + * bytes of the DP RAM and relocates the I2C parameter area to the + * IDMA1 space. The remaining DP RAM is available for buffer descriptors + * or other use. + */ +#ifndef __CPM_8XX__ +#define __CPM_8XX__ + +#include +#include + +/* CPM Command register. +*/ +#define CPM_CR_RST ((ushort)0x8000) +#define CPM_CR_OPCODE ((ushort)0x0f00) +#define CPM_CR_CHAN ((ushort)0x00f0) +#define CPM_CR_FLG ((ushort)0x0001) + +/* Some commands (there are more...later) +*/ +#define CPM_CR_INIT_TRX ((ushort)0x0000) +#define CPM_CR_INIT_RX ((ushort)0x0001) +#define CPM_CR_INIT_TX ((ushort)0x0002) +#define CPM_CR_HUNT_MODE ((ushort)0x0003) +#define CPM_CR_STOP_TX ((ushort)0x0004) +#define CPM_CR_GRA_STOP_TX ((ushort)0x0005) +#define CPM_CR_RESTART_TX ((ushort)0x0006) +#define CPM_CR_CLOSE_RX_BD ((ushort)0x0007) +#define CPM_CR_SET_GADDR ((ushort)0x0008) +#define CPM_CR_SET_TIMER CPM_CR_SET_GADDR + +/* Channel numbers. +*/ +#define CPM_CR_CH_SCC1 ((ushort)0x0000) +#define CPM_CR_CH_I2C ((ushort)0x0001) /* I2C and IDMA1 */ +#define CPM_CR_CH_SCC2 ((ushort)0x0004) +#define CPM_CR_CH_SPI ((ushort)0x0005) /* SPI / IDMA2 / Timers */ +#define CPM_CR_CH_TIMER CPM_CR_CH_SPI +#define CPM_CR_CH_SCC3 ((ushort)0x0008) +#define CPM_CR_CH_SMC1 ((ushort)0x0009) /* SMC1 / DSP1 */ +#define CPM_CR_CH_SCC4 ((ushort)0x000c) +#define CPM_CR_CH_SMC2 ((ushort)0x000d) /* SMC2 / DSP2 */ + +#define mk_cr_cmd(CH, CMD) ((CMD << 8) | (CH << 4)) + +/* The dual ported RAM is multi-functional. Some areas can be (and are + * being) used for microcode. There is an area that can only be used + * as data ram for buffer descriptors, which is all we use right now. + * Currently the first 512 and last 256 bytes are used for microcode. + */ +#define CPM_DATAONLY_BASE ((uint)0x0800) +#define CPM_DATAONLY_SIZE ((uint)0x0700) +#define CPM_DP_NOSPACE ((uint)0x7fffffff) + +/* Export the base address of the communication processor registers + * and dual port ram. + */ +extern cpm8xx_t *cpmp; /* Pointer to comm processor */ +extern unsigned long cpm_dpalloc(uint size, uint align); +extern int cpm_dpfree(unsigned long offset); +extern unsigned long cpm_dpalloc_fixed(unsigned long offset, uint size, uint align); +extern void cpm_dpdump(void); +extern void *cpm_dpram_addr(unsigned long offset); +extern uint cpm_dpram_phys(u8* addr); +extern void cpm_setbrg(uint brg, uint rate); + +extern uint m8xx_cpm_hostalloc(uint size); +extern int m8xx_cpm_hostfree(uint start); +extern void m8xx_cpm_hostdump(void); + +extern void cpm_load_patch(volatile immap_t *immr); + +/* Buffer descriptors used by many of the CPM protocols. +*/ +typedef struct cpm_buf_desc { + ushort cbd_sc; /* Status and Control */ + ushort cbd_datlen; /* Data length in buffer */ + uint cbd_bufaddr; /* Buffer address in host memory */ +} cbd_t; + +#define BD_SC_EMPTY ((ushort)0x8000) /* Receive is empty */ +#define BD_SC_READY ((ushort)0x8000) /* Transmit is ready */ +#define BD_SC_WRAP ((ushort)0x2000) /* Last buffer descriptor */ +#define BD_SC_INTRPT ((ushort)0x1000) /* Interrupt on change */ +#define BD_SC_LAST ((ushort)0x0800) /* Last buffer in frame */ +#define BD_SC_TC ((ushort)0x0400) /* Transmit CRC */ +#define BD_SC_CM ((ushort)0x0200) /* Continous mode */ +#define BD_SC_ID ((ushort)0x0100) /* Rec'd too many idles */ +#define BD_SC_P ((ushort)0x0100) /* xmt preamble */ +#define BD_SC_BR ((ushort)0x0020) /* Break received */ +#define BD_SC_FR ((ushort)0x0010) /* Framing error */ +#define BD_SC_PR ((ushort)0x0008) /* Parity error */ +#define BD_SC_NAK ((ushort)0x0004) /* NAK - did not respond */ +#define BD_SC_OV ((ushort)0x0002) /* Overrun */ +#define BD_SC_UN ((ushort)0x0002) /* Underrun */ +#define BD_SC_CD ((ushort)0x0001) /* ?? */ +#define BD_SC_CL ((ushort)0x0001) /* Collision */ + +/* Parameter RAM offsets. +*/ +#define PROFF_SCC1 ((uint)0x0000) +#define PROFF_IIC ((uint)0x0080) +#define PROFF_SCC2 ((uint)0x0100) +#define PROFF_SPI ((uint)0x0180) +#define PROFF_SCC3 ((uint)0x0200) +#define PROFF_SMC1 ((uint)0x0280) +#define PROFF_SCC4 ((uint)0x0300) +#define PROFF_SMC2 ((uint)0x0380) + +/* Define enough so I can at least use the serial port as a UART. + * The MBX uses SMC1 as the host serial port. + */ +typedef struct smc_uart { + ushort smc_rbase; /* Rx Buffer descriptor base address */ + ushort smc_tbase; /* Tx Buffer descriptor base address */ + u_char smc_rfcr; /* Rx function code */ + u_char smc_tfcr; /* Tx function code */ + ushort smc_mrblr; /* Max receive buffer length */ + uint smc_rstate; /* Internal */ + uint smc_idp; /* Internal */ + ushort smc_rbptr; /* Internal */ + ushort smc_ibc; /* Internal */ + uint smc_rxtmp; /* Internal */ + uint smc_tstate; /* Internal */ + uint smc_tdp; /* Internal */ + ushort smc_tbptr; /* Internal */ + ushort smc_tbc; /* Internal */ + uint smc_txtmp; /* Internal */ + ushort smc_maxidl; /* Maximum idle characters */ + ushort smc_tmpidl; /* Temporary idle counter */ + ushort smc_brklen; /* Last received break length */ + ushort smc_brkec; /* rcv'd break condition counter */ + ushort smc_brkcr; /* xmt break count register */ + ushort smc_rmask; /* Temporary bit mask */ + char res1[8]; /* Reserved */ + ushort smc_rpbase; /* Relocation pointer */ +} smc_uart_t; + +/* Function code bits. +*/ +#define SMC_EB ((u_char)0x10) /* Set big endian byte order */ + +/* SMC uart mode register. +*/ +#define SMCMR_REN ((ushort)0x0001) +#define SMCMR_TEN ((ushort)0x0002) +#define SMCMR_DM ((ushort)0x000c) +#define SMCMR_SM_GCI ((ushort)0x0000) +#define SMCMR_SM_UART ((ushort)0x0020) +#define SMCMR_SM_TRANS ((ushort)0x0030) +#define SMCMR_SM_MASK ((ushort)0x0030) +#define SMCMR_PM_EVEN ((ushort)0x0100) /* Even parity, else odd */ +#define SMCMR_REVD SMCMR_PM_EVEN +#define SMCMR_PEN ((ushort)0x0200) /* Parity enable */ +#define SMCMR_BS SMCMR_PEN +#define SMCMR_SL ((ushort)0x0400) /* Two stops, else one */ +#define SMCR_CLEN_MASK ((ushort)0x7800) /* Character length */ +#define smcr_mk_clen(C) (((C) << 11) & SMCR_CLEN_MASK) + +/* SMC2 as Centronics parallel printer. It is half duplex, in that + * it can only receive or transmit. The parameter ram values for + * each direction are either unique or properly overlap, so we can + * include them in one structure. + */ +typedef struct smc_centronics { + ushort scent_rbase; + ushort scent_tbase; + u_char scent_cfcr; + u_char scent_smask; + ushort scent_mrblr; + uint scent_rstate; + uint scent_r_ptr; + ushort scent_rbptr; + ushort scent_r_cnt; + uint scent_rtemp; + uint scent_tstate; + uint scent_t_ptr; + ushort scent_tbptr; + ushort scent_t_cnt; + uint scent_ttemp; + ushort scent_max_sl; + ushort scent_sl_cnt; + ushort scent_character1; + ushort scent_character2; + ushort scent_character3; + ushort scent_character4; + ushort scent_character5; + ushort scent_character6; + ushort scent_character7; + ushort scent_character8; + ushort scent_rccm; + ushort scent_rccr; +} smc_cent_t; + +/* Centronics Status Mask Register. +*/ +#define SMC_CENT_F ((u_char)0x08) +#define SMC_CENT_PE ((u_char)0x04) +#define SMC_CENT_S ((u_char)0x02) + +/* SMC Event and Mask register. +*/ +#define SMCM_BRKE ((unsigned char)0x40) /* When in UART Mode */ +#define SMCM_BRK ((unsigned char)0x10) /* When in UART Mode */ +#define SMCM_TXE ((unsigned char)0x10) /* When in Transparent Mode */ +#define SMCM_BSY ((unsigned char)0x04) +#define SMCM_TX ((unsigned char)0x02) +#define SMCM_RX ((unsigned char)0x01) + +/* Baud rate generators. +*/ +#define CPM_BRG_RST ((uint)0x00020000) +#define CPM_BRG_EN ((uint)0x00010000) +#define CPM_BRG_EXTC_INT ((uint)0x00000000) +#define CPM_BRG_EXTC_CLK2 ((uint)0x00004000) +#define CPM_BRG_EXTC_CLK6 ((uint)0x00008000) +#define CPM_BRG_ATB ((uint)0x00002000) +#define CPM_BRG_CD_MASK ((uint)0x00001ffe) +#define CPM_BRG_DIV16 ((uint)0x00000001) + +/* SI Clock Route Register +*/ +#define SICR_RCLK_SCC1_BRG1 ((uint)0x00000000) +#define SICR_TCLK_SCC1_BRG1 ((uint)0x00000000) +#define SICR_RCLK_SCC2_BRG2 ((uint)0x00000800) +#define SICR_TCLK_SCC2_BRG2 ((uint)0x00000100) +#define SICR_RCLK_SCC3_BRG3 ((uint)0x00100000) +#define SICR_TCLK_SCC3_BRG3 ((uint)0x00020000) +#define SICR_RCLK_SCC4_BRG4 ((uint)0x18000000) +#define SICR_TCLK_SCC4_BRG4 ((uint)0x03000000) + +/* SCCs. +*/ +#define SCC_GSMRH_IRP ((uint)0x00040000) +#define SCC_GSMRH_GDE ((uint)0x00010000) +#define SCC_GSMRH_TCRC_CCITT ((uint)0x00008000) +#define SCC_GSMRH_TCRC_BISYNC ((uint)0x00004000) +#define SCC_GSMRH_TCRC_HDLC ((uint)0x00000000) +#define SCC_GSMRH_REVD ((uint)0x00002000) +#define SCC_GSMRH_TRX ((uint)0x00001000) +#define SCC_GSMRH_TTX ((uint)0x00000800) +#define SCC_GSMRH_CDP ((uint)0x00000400) +#define SCC_GSMRH_CTSP ((uint)0x00000200) +#define SCC_GSMRH_CDS ((uint)0x00000100) +#define SCC_GSMRH_CTSS ((uint)0x00000080) +#define SCC_GSMRH_TFL ((uint)0x00000040) +#define SCC_GSMRH_RFW ((uint)0x00000020) +#define SCC_GSMRH_TXSY ((uint)0x00000010) +#define SCC_GSMRH_SYNL16 ((uint)0x0000000c) +#define SCC_GSMRH_SYNL8 ((uint)0x00000008) +#define SCC_GSMRH_SYNL4 ((uint)0x00000004) +#define SCC_GSMRH_RTSM ((uint)0x00000002) +#define SCC_GSMRH_RSYN ((uint)0x00000001) + +#define SCC_GSMRL_SIR ((uint)0x80000000) /* SCC2 only */ +#define SCC_GSMRL_EDGE_NONE ((uint)0x60000000) +#define SCC_GSMRL_EDGE_NEG ((uint)0x40000000) +#define SCC_GSMRL_EDGE_POS ((uint)0x20000000) +#define SCC_GSMRL_EDGE_BOTH ((uint)0x00000000) +#define SCC_GSMRL_TCI ((uint)0x10000000) +#define SCC_GSMRL_TSNC_3 ((uint)0x0c000000) +#define SCC_GSMRL_TSNC_4 ((uint)0x08000000) +#define SCC_GSMRL_TSNC_14 ((uint)0x04000000) +#define SCC_GSMRL_TSNC_INF ((uint)0x00000000) +#define SCC_GSMRL_RINV ((uint)0x02000000) +#define SCC_GSMRL_TINV ((uint)0x01000000) +#define SCC_GSMRL_TPL_128 ((uint)0x00c00000) +#define SCC_GSMRL_TPL_64 ((uint)0x00a00000) +#define SCC_GSMRL_TPL_48 ((uint)0x00800000) +#define SCC_GSMRL_TPL_32 ((uint)0x00600000) +#define SCC_GSMRL_TPL_16 ((uint)0x00400000) +#define SCC_GSMRL_TPL_8 ((uint)0x00200000) +#define SCC_GSMRL_TPL_NONE ((uint)0x00000000) +#define SCC_GSMRL_TPP_ALL1 ((uint)0x00180000) +#define SCC_GSMRL_TPP_01 ((uint)0x00100000) +#define SCC_GSMRL_TPP_10 ((uint)0x00080000) +#define SCC_GSMRL_TPP_ZEROS ((uint)0x00000000) +#define SCC_GSMRL_TEND ((uint)0x00040000) +#define SCC_GSMRL_TDCR_32 ((uint)0x00030000) +#define SCC_GSMRL_TDCR_16 ((uint)0x00020000) +#define SCC_GSMRL_TDCR_8 ((uint)0x00010000) +#define SCC_GSMRL_TDCR_1 ((uint)0x00000000) +#define SCC_GSMRL_RDCR_32 ((uint)0x0000c000) +#define SCC_GSMRL_RDCR_16 ((uint)0x00008000) +#define SCC_GSMRL_RDCR_8 ((uint)0x00004000) +#define SCC_GSMRL_RDCR_1 ((uint)0x00000000) +#define SCC_GSMRL_RENC_DFMAN ((uint)0x00003000) +#define SCC_GSMRL_RENC_MANCH ((uint)0x00002000) +#define SCC_GSMRL_RENC_FM0 ((uint)0x00001000) +#define SCC_GSMRL_RENC_NRZI ((uint)0x00000800) +#define SCC_GSMRL_RENC_NRZ ((uint)0x00000000) +#define SCC_GSMRL_TENC_DFMAN ((uint)0x00000600) +#define SCC_GSMRL_TENC_MANCH ((uint)0x00000400) +#define SCC_GSMRL_TENC_FM0 ((uint)0x00000200) +#define SCC_GSMRL_TENC_NRZI ((uint)0x00000100) +#define SCC_GSMRL_TENC_NRZ ((uint)0x00000000) +#define SCC_GSMRL_DIAG_LE ((uint)0x000000c0) /* Loop and echo */ +#define SCC_GSMRL_DIAG_ECHO ((uint)0x00000080) +#define SCC_GSMRL_DIAG_LOOP ((uint)0x00000040) +#define SCC_GSMRL_DIAG_NORM ((uint)0x00000000) +#define SCC_GSMRL_ENR ((uint)0x00000020) +#define SCC_GSMRL_ENT ((uint)0x00000010) +#define SCC_GSMRL_MODE_ENET ((uint)0x0000000c) +#define SCC_GSMRL_MODE_QMC ((uint)0x0000000a) +#define SCC_GSMRL_MODE_DDCMP ((uint)0x00000009) +#define SCC_GSMRL_MODE_BISYNC ((uint)0x00000008) +#define SCC_GSMRL_MODE_V14 ((uint)0x00000007) +#define SCC_GSMRL_MODE_AHDLC ((uint)0x00000006) +#define SCC_GSMRL_MODE_PROFIBUS ((uint)0x00000005) +#define SCC_GSMRL_MODE_UART ((uint)0x00000004) +#define SCC_GSMRL_MODE_SS7 ((uint)0x00000003) +#define SCC_GSMRL_MODE_ATALK ((uint)0x00000002) +#define SCC_GSMRL_MODE_HDLC ((uint)0x00000000) + +#define SCC_TODR_TOD ((ushort)0x8000) + +/* SCC Event and Mask register. +*/ +#define SCCM_TXE ((unsigned char)0x10) +#define SCCM_BSY ((unsigned char)0x04) +#define SCCM_TX ((unsigned char)0x02) +#define SCCM_RX ((unsigned char)0x01) + +typedef struct scc_param { + ushort scc_rbase; /* Rx Buffer descriptor base address */ + ushort scc_tbase; /* Tx Buffer descriptor base address */ + u_char scc_rfcr; /* Rx function code */ + u_char scc_tfcr; /* Tx function code */ + ushort scc_mrblr; /* Max receive buffer length */ + uint scc_rstate; /* Internal */ + uint scc_idp; /* Internal */ + ushort scc_rbptr; /* Internal */ + ushort scc_ibc; /* Internal */ + uint scc_rxtmp; /* Internal */ + uint scc_tstate; /* Internal */ + uint scc_tdp; /* Internal */ + ushort scc_tbptr; /* Internal */ + ushort scc_tbc; /* Internal */ + uint scc_txtmp; /* Internal */ + uint scc_rcrc; /* Internal */ + uint scc_tcrc; /* Internal */ +} sccp_t; + +/* Function code bits. +*/ +#define SCC_EB ((u_char)0x10) /* Set big endian byte order */ + +/* CPM Ethernet through SCCx. + */ +typedef struct scc_enet { + sccp_t sen_genscc; + uint sen_cpres; /* Preset CRC */ + uint sen_cmask; /* Constant mask for CRC */ + uint sen_crcec; /* CRC Error counter */ + uint sen_alec; /* alignment error counter */ + uint sen_disfc; /* discard frame counter */ + ushort sen_pads; /* Tx short frame pad character */ + ushort sen_retlim; /* Retry limit threshold */ + ushort sen_retcnt; /* Retry limit counter */ + ushort sen_maxflr; /* maximum frame length register */ + ushort sen_minflr; /* minimum frame length register */ + ushort sen_maxd1; /* maximum DMA1 length */ + ushort sen_maxd2; /* maximum DMA2 length */ + ushort sen_maxd; /* Rx max DMA */ + ushort sen_dmacnt; /* Rx DMA counter */ + ushort sen_maxb; /* Max BD byte count */ + ushort sen_gaddr1; /* Group address filter */ + ushort sen_gaddr2; + ushort sen_gaddr3; + ushort sen_gaddr4; + uint sen_tbuf0data0; /* Save area 0 - current frame */ + uint sen_tbuf0data1; /* Save area 1 - current frame */ + uint sen_tbuf0rba; /* Internal */ + uint sen_tbuf0crc; /* Internal */ + ushort sen_tbuf0bcnt; /* Internal */ + ushort sen_paddrh; /* physical address (MSB) */ + ushort sen_paddrm; + ushort sen_paddrl; /* physical address (LSB) */ + ushort sen_pper; /* persistence */ + ushort sen_rfbdptr; /* Rx first BD pointer */ + ushort sen_tfbdptr; /* Tx first BD pointer */ + ushort sen_tlbdptr; /* Tx last BD pointer */ + uint sen_tbuf1data0; /* Save area 0 - current frame */ + uint sen_tbuf1data1; /* Save area 1 - current frame */ + uint sen_tbuf1rba; /* Internal */ + uint sen_tbuf1crc; /* Internal */ + ushort sen_tbuf1bcnt; /* Internal */ + ushort sen_txlen; /* Tx Frame length counter */ + ushort sen_iaddr1; /* Individual address filter */ + ushort sen_iaddr2; + ushort sen_iaddr3; + ushort sen_iaddr4; + ushort sen_boffcnt; /* Backoff counter */ + + /* NOTE: Some versions of the manual have the following items + * incorrectly documented. Below is the proper order. + */ + ushort sen_taddrh; /* temp address (MSB) */ + ushort sen_taddrm; + ushort sen_taddrl; /* temp address (LSB) */ +} scc_enet_t; + +/* SCC Event register as used by Ethernet. +*/ +#define SCCE_ENET_GRA ((ushort)0x0080) /* Graceful stop complete */ +#define SCCE_ENET_TXE ((ushort)0x0010) /* Transmit Error */ +#define SCCE_ENET_RXF ((ushort)0x0008) /* Full frame received */ +#define SCCE_ENET_BSY ((ushort)0x0004) /* All incoming buffers full */ +#define SCCE_ENET_TXB ((ushort)0x0002) /* A buffer was transmitted */ +#define SCCE_ENET_RXB ((ushort)0x0001) /* A buffer was received */ + +/* SCC Mode Register (PMSR) as used by Ethernet. +*/ +#define SCC_PSMR_HBC ((ushort)0x8000) /* Enable heartbeat */ +#define SCC_PSMR_FC ((ushort)0x4000) /* Force collision */ +#define SCC_PSMR_RSH ((ushort)0x2000) /* Receive short frames */ +#define SCC_PSMR_IAM ((ushort)0x1000) /* Check individual hash */ +#define SCC_PSMR_ENCRC ((ushort)0x0800) /* Ethernet CRC mode */ +#define SCC_PSMR_PRO ((ushort)0x0200) /* Promiscuous mode */ +#define SCC_PSMR_BRO ((ushort)0x0100) /* Catch broadcast pkts */ +#define SCC_PSMR_SBT ((ushort)0x0080) /* Special backoff timer */ +#define SCC_PSMR_LPB ((ushort)0x0040) /* Set Loopback mode */ +#define SCC_PSMR_SIP ((ushort)0x0020) /* Sample Input Pins */ +#define SCC_PSMR_LCW ((ushort)0x0010) /* Late collision window */ +#define SCC_PSMR_NIB22 ((ushort)0x000a) /* Start frame search */ +#define SCC_PSMR_FDE ((ushort)0x0001) /* Full duplex enable */ + +/* Buffer descriptor control/status used by Ethernet receive. +*/ +#define BD_ENET_RX_EMPTY ((ushort)0x8000) +#define BD_ENET_RX_WRAP ((ushort)0x2000) +#define BD_ENET_RX_INTR ((ushort)0x1000) +#define BD_ENET_RX_LAST ((ushort)0x0800) +#define BD_ENET_RX_FIRST ((ushort)0x0400) +#define BD_ENET_RX_MISS ((ushort)0x0100) +#define BD_ENET_RX_LG ((ushort)0x0020) +#define BD_ENET_RX_NO ((ushort)0x0010) +#define BD_ENET_RX_SH ((ushort)0x0008) +#define BD_ENET_RX_CR ((ushort)0x0004) +#define BD_ENET_RX_OV ((ushort)0x0002) +#define BD_ENET_RX_CL ((ushort)0x0001) +#define BD_ENET_RX_BC ((ushort)0x0080) /* DA is Broadcast */ +#define BD_ENET_RX_MC ((ushort)0x0040) /* DA is Multicast */ +#define BD_ENET_RX_STATS ((ushort)0x013f) /* All status bits */ + +/* Buffer descriptor control/status used by Ethernet transmit. +*/ +#define BD_ENET_TX_READY ((ushort)0x8000) +#define BD_ENET_TX_PAD ((ushort)0x4000) +#define BD_ENET_TX_WRAP ((ushort)0x2000) +#define BD_ENET_TX_INTR ((ushort)0x1000) +#define BD_ENET_TX_LAST ((ushort)0x0800) +#define BD_ENET_TX_TC ((ushort)0x0400) +#define BD_ENET_TX_DEF ((ushort)0x0200) +#define BD_ENET_TX_HB ((ushort)0x0100) +#define BD_ENET_TX_LC ((ushort)0x0080) +#define BD_ENET_TX_RL ((ushort)0x0040) +#define BD_ENET_TX_RCMASK ((ushort)0x003c) +#define BD_ENET_TX_UN ((ushort)0x0002) +#define BD_ENET_TX_CSL ((ushort)0x0001) +#define BD_ENET_TX_STATS ((ushort)0x03ff) /* All status bits */ + +/* SCC as UART +*/ +typedef struct scc_uart { + sccp_t scc_genscc; + char res1[8]; /* Reserved */ + ushort scc_maxidl; /* Maximum idle chars */ + ushort scc_idlc; /* temp idle counter */ + ushort scc_brkcr; /* Break count register */ + ushort scc_parec; /* receive parity error counter */ + ushort scc_frmec; /* receive framing error counter */ + ushort scc_nosec; /* receive noise counter */ + ushort scc_brkec; /* receive break condition counter */ + ushort scc_brkln; /* last received break length */ + ushort scc_uaddr1; /* UART address character 1 */ + ushort scc_uaddr2; /* UART address character 2 */ + ushort scc_rtemp; /* Temp storage */ + ushort scc_toseq; /* Transmit out of sequence char */ + ushort scc_char1; /* control character 1 */ + ushort scc_char2; /* control character 2 */ + ushort scc_char3; /* control character 3 */ + ushort scc_char4; /* control character 4 */ + ushort scc_char5; /* control character 5 */ + ushort scc_char6; /* control character 6 */ + ushort scc_char7; /* control character 7 */ + ushort scc_char8; /* control character 8 */ + ushort scc_rccm; /* receive control character mask */ + ushort scc_rccr; /* receive control character register */ + ushort scc_rlbc; /* receive last break character */ +} scc_uart_t; + +/* SCC Event and Mask registers when it is used as a UART. +*/ +#define UART_SCCM_GLR ((ushort)0x1000) +#define UART_SCCM_GLT ((ushort)0x0800) +#define UART_SCCM_AB ((ushort)0x0200) +#define UART_SCCM_IDL ((ushort)0x0100) +#define UART_SCCM_GRA ((ushort)0x0080) +#define UART_SCCM_BRKE ((ushort)0x0040) +#define UART_SCCM_BRKS ((ushort)0x0020) +#define UART_SCCM_CCR ((ushort)0x0008) +#define UART_SCCM_BSY ((ushort)0x0004) +#define UART_SCCM_TX ((ushort)0x0002) +#define UART_SCCM_RX ((ushort)0x0001) + +/* The SCC PMSR when used as a UART. +*/ +#define SCU_PSMR_FLC ((ushort)0x8000) +#define SCU_PSMR_SL ((ushort)0x4000) +#define SCU_PSMR_CL ((ushort)0x3000) +#define SCU_PSMR_UM ((ushort)0x0c00) +#define SCU_PSMR_FRZ ((ushort)0x0200) +#define SCU_PSMR_RZS ((ushort)0x0100) +#define SCU_PSMR_SYN ((ushort)0x0080) +#define SCU_PSMR_DRT ((ushort)0x0040) +#define SCU_PSMR_PEN ((ushort)0x0010) +#define SCU_PSMR_RPM ((ushort)0x000c) +#define SCU_PSMR_REVP ((ushort)0x0008) +#define SCU_PSMR_TPM ((ushort)0x0003) +#define SCU_PSMR_TEVP ((ushort)0x0002) + +/* CPM Transparent mode SCC. + */ +typedef struct scc_trans { + sccp_t st_genscc; + uint st_cpres; /* Preset CRC */ + uint st_cmask; /* Constant mask for CRC */ +} scc_trans_t; + +#define BD_SCC_TX_LAST ((ushort)0x0800) + +/* IIC parameter RAM. +*/ +typedef struct iic { + ushort iic_rbase; /* Rx Buffer descriptor base address */ + ushort iic_tbase; /* Tx Buffer descriptor base address */ + u_char iic_rfcr; /* Rx function code */ + u_char iic_tfcr; /* Tx function code */ + ushort iic_mrblr; /* Max receive buffer length */ + uint iic_rstate; /* Internal */ + uint iic_rdp; /* Internal */ + ushort iic_rbptr; /* Internal */ + ushort iic_rbc; /* Internal */ + uint iic_rxtmp; /* Internal */ + uint iic_tstate; /* Internal */ + uint iic_tdp; /* Internal */ + ushort iic_tbptr; /* Internal */ + ushort iic_tbc; /* Internal */ + uint iic_txtmp; /* Internal */ + char res1[4]; /* Reserved */ + ushort iic_rpbase; /* Relocation pointer */ + char res2[2]; /* Reserved */ +} iic_t; + +#define BD_IIC_START ((ushort)0x0400) + +/* SPI parameter RAM. +*/ +typedef struct spi { + ushort spi_rbase; /* Rx Buffer descriptor base address */ + ushort spi_tbase; /* Tx Buffer descriptor base address */ + u_char spi_rfcr; /* Rx function code */ + u_char spi_tfcr; /* Tx function code */ + ushort spi_mrblr; /* Max receive buffer length */ + uint spi_rstate; /* Internal */ + uint spi_rdp; /* Internal */ + ushort spi_rbptr; /* Internal */ + ushort spi_rbc; /* Internal */ + uint spi_rxtmp; /* Internal */ + uint spi_tstate; /* Internal */ + uint spi_tdp; /* Internal */ + ushort spi_tbptr; /* Internal */ + ushort spi_tbc; /* Internal */ + uint spi_txtmp; /* Internal */ + uint spi_res; + ushort spi_rpbase; /* Relocation pointer */ + ushort spi_res2; +} spi_t; + +/* SPI Mode register. +*/ +#define SPMODE_LOOP ((ushort)0x4000) /* Loopback */ +#define SPMODE_CI ((ushort)0x2000) /* Clock Invert */ +#define SPMODE_CP ((ushort)0x1000) /* Clock Phase */ +#define SPMODE_DIV16 ((ushort)0x0800) /* BRG/16 mode */ +#define SPMODE_REV ((ushort)0x0400) /* Reversed Data */ +#define SPMODE_MSTR ((ushort)0x0200) /* SPI Master */ +#define SPMODE_EN ((ushort)0x0100) /* Enable */ +#define SPMODE_LENMSK ((ushort)0x00f0) /* character length */ +#define SPMODE_LEN4 ((ushort)0x0030) /* 4 bits per char */ +#define SPMODE_LEN8 ((ushort)0x0070) /* 8 bits per char */ +#define SPMODE_LEN16 ((ushort)0x00f0) /* 16 bits per char */ +#define SPMODE_PMMSK ((ushort)0x000f) /* prescale modulus */ + +/* SPIE fields */ +#define SPIE_MME 0x20 +#define SPIE_TXE 0x10 +#define SPIE_BSY 0x04 +#define SPIE_TXB 0x02 +#define SPIE_RXB 0x01 + +/* + * RISC Controller Configuration Register definitons + */ +#define RCCR_TIME 0x8000 /* RISC Timer Enable */ +#define RCCR_TIMEP(t) (((t) & 0x3F)<<8) /* RISC Timer Period */ +#define RCCR_TIME_MASK 0x00FF /* not RISC Timer related bits */ + +/* RISC Timer Parameter RAM offset */ +#define PROFF_RTMR ((uint)0x01B0) + +typedef struct risc_timer_pram { + unsigned short tm_base; /* RISC Timer Table Base Address */ + unsigned short tm_ptr; /* RISC Timer Table Pointer (internal) */ + unsigned short r_tmr; /* RISC Timer Mode Register */ + unsigned short r_tmv; /* RISC Timer Valid Register */ + unsigned long tm_cmd; /* RISC Timer Command Register */ + unsigned long tm_cnt; /* RISC Timer Internal Count */ +} rt_pram_t; + +/* Bits in RISC Timer Command Register */ +#define TM_CMD_VALID 0x80000000 /* Valid - Enables the timer */ +#define TM_CMD_RESTART 0x40000000 /* Restart - for automatic restart */ +#define TM_CMD_PWM 0x20000000 /* Run in Pulse Width Modulation Mode */ +#define TM_CMD_NUM(n) (((n)&0xF)<<16) /* Timer Number */ +#define TM_CMD_PERIOD(p) ((p)&0xFFFF) /* Timer Period */ + +/* CPM interrupts. There are nearly 32 interrupts generated by CPM + * channels or devices. All of these are presented to the PPC core + * as a single interrupt. The CPM interrupt handler dispatches its + * own handlers, in a similar fashion to the PPC core handler. We + * use the table as defined in the manuals (i.e. no special high + * priority and SCC1 == SCCa, etc...). + */ +#define CPMVEC_NR 32 +#define CPMVEC_PIO_PC15 ((ushort)0x1f) +#define CPMVEC_SCC1 ((ushort)0x1e) +#define CPMVEC_SCC2 ((ushort)0x1d) +#define CPMVEC_SCC3 ((ushort)0x1c) +#define CPMVEC_SCC4 ((ushort)0x1b) +#define CPMVEC_PIO_PC14 ((ushort)0x1a) +#define CPMVEC_TIMER1 ((ushort)0x19) +#define CPMVEC_PIO_PC13 ((ushort)0x18) +#define CPMVEC_PIO_PC12 ((ushort)0x17) +#define CPMVEC_SDMA_CB_ERR ((ushort)0x16) +#define CPMVEC_IDMA1 ((ushort)0x15) +#define CPMVEC_IDMA2 ((ushort)0x14) +#define CPMVEC_TIMER2 ((ushort)0x12) +#define CPMVEC_RISCTIMER ((ushort)0x11) +#define CPMVEC_I2C ((ushort)0x10) +#define CPMVEC_PIO_PC11 ((ushort)0x0f) +#define CPMVEC_PIO_PC10 ((ushort)0x0e) +#define CPMVEC_TIMER3 ((ushort)0x0c) +#define CPMVEC_PIO_PC9 ((ushort)0x0b) +#define CPMVEC_PIO_PC8 ((ushort)0x0a) +#define CPMVEC_PIO_PC7 ((ushort)0x09) +#define CPMVEC_TIMER4 ((ushort)0x07) +#define CPMVEC_PIO_PC6 ((ushort)0x06) +#define CPMVEC_SPI ((ushort)0x05) +#define CPMVEC_SMC1 ((ushort)0x04) +#define CPMVEC_SMC2 ((ushort)0x03) +#define CPMVEC_PIO_PC5 ((ushort)0x02) +#define CPMVEC_PIO_PC4 ((ushort)0x01) +#define CPMVEC_ERROR ((ushort)0x00) + +/* CPM interrupt configuration vector. +*/ +#define CICR_SCD_SCC4 ((uint)0x00c00000) /* SCC4 @ SCCd */ +#define CICR_SCC_SCC3 ((uint)0x00200000) /* SCC3 @ SCCc */ +#define CICR_SCB_SCC2 ((uint)0x00040000) /* SCC2 @ SCCb */ +#define CICR_SCA_SCC1 ((uint)0x00000000) /* SCC1 @ SCCa */ +#define CICR_IRL_MASK ((uint)0x0000e000) /* Core interrrupt */ +#define CICR_HP_MASK ((uint)0x00001f00) /* Hi-pri int. */ +#define CICR_IEN ((uint)0x00000080) /* Int. enable */ +#define CICR_SPS ((uint)0x00000001) /* SCC Spread */ + +extern void cpm_install_handler(int vec, void (*handler)(void *), void *dev_id); +extern void cpm_free_handler(int vec); + +#endif /* __CPM_8XX__ */ diff --git a/include/asm-powerpc/cpm2.h b/include/asm-powerpc/cpm2.h new file mode 100644 index 00000000000..12a2860f9a9 --- /dev/null +++ b/include/asm-powerpc/cpm2.h @@ -0,0 +1,1248 @@ +/* + * Communication Processor Module v2. + * + * This file contains structures and information for the communication + * processor channels found in the dual port RAM or parameter RAM. + * All CPM control and status is available through the CPM2 internal + * memory map. See immap_cpm2.h for details. + */ +#ifdef __KERNEL__ +#ifndef __CPM2__ +#define __CPM2__ + +#include + +/* CPM Command register. +*/ +#define CPM_CR_RST ((uint)0x80000000) +#define CPM_CR_PAGE ((uint)0x7c000000) +#define CPM_CR_SBLOCK ((uint)0x03e00000) +#define CPM_CR_FLG ((uint)0x00010000) +#define CPM_CR_MCN ((uint)0x00003fc0) +#define CPM_CR_OPCODE ((uint)0x0000000f) + +/* Device sub-block and page codes. +*/ +#define CPM_CR_SCC1_SBLOCK (0x04) +#define CPM_CR_SCC2_SBLOCK (0x05) +#define CPM_CR_SCC3_SBLOCK (0x06) +#define CPM_CR_SCC4_SBLOCK (0x07) +#define CPM_CR_SMC1_SBLOCK (0x08) +#define CPM_CR_SMC2_SBLOCK (0x09) +#define CPM_CR_SPI_SBLOCK (0x0a) +#define CPM_CR_I2C_SBLOCK (0x0b) +#define CPM_CR_TIMER_SBLOCK (0x0f) +#define CPM_CR_RAND_SBLOCK (0x0e) +#define CPM_CR_FCC1_SBLOCK (0x10) +#define CPM_CR_FCC2_SBLOCK (0x11) +#define CPM_CR_FCC3_SBLOCK (0x12) +#define CPM_CR_IDMA1_SBLOCK (0x14) +#define CPM_CR_IDMA2_SBLOCK (0x15) +#define CPM_CR_IDMA3_SBLOCK (0x16) +#define CPM_CR_IDMA4_SBLOCK (0x17) +#define CPM_CR_MCC1_SBLOCK (0x1c) + +#define CPM_CR_FCC_SBLOCK(x) (x + 0x10) + +#define CPM_CR_SCC1_PAGE (0x00) +#define CPM_CR_SCC2_PAGE (0x01) +#define CPM_CR_SCC3_PAGE (0x02) +#define CPM_CR_SCC4_PAGE (0x03) +#define CPM_CR_SMC1_PAGE (0x07) +#define CPM_CR_SMC2_PAGE (0x08) +#define CPM_CR_SPI_PAGE (0x09) +#define CPM_CR_I2C_PAGE (0x0a) +#define CPM_CR_TIMER_PAGE (0x0a) +#define CPM_CR_RAND_PAGE (0x0a) +#define CPM_CR_FCC1_PAGE (0x04) +#define CPM_CR_FCC2_PAGE (0x05) +#define CPM_CR_FCC3_PAGE (0x06) +#define CPM_CR_IDMA1_PAGE (0x07) +#define CPM_CR_IDMA2_PAGE (0x08) +#define CPM_CR_IDMA3_PAGE (0x09) +#define CPM_CR_IDMA4_PAGE (0x0a) +#define CPM_CR_MCC1_PAGE (0x07) +#define CPM_CR_MCC2_PAGE (0x08) + +#define CPM_CR_FCC_PAGE(x) (x + 0x04) + +/* Some opcodes (there are more...later) +*/ +#define CPM_CR_INIT_TRX ((ushort)0x0000) +#define CPM_CR_INIT_RX ((ushort)0x0001) +#define CPM_CR_INIT_TX ((ushort)0x0002) +#define CPM_CR_HUNT_MODE ((ushort)0x0003) +#define CPM_CR_STOP_TX ((ushort)0x0004) +#define CPM_CR_GRA_STOP_TX ((ushort)0x0005) +#define CPM_CR_RESTART_TX ((ushort)0x0006) +#define CPM_CR_SET_GADDR ((ushort)0x0008) +#define CPM_CR_START_IDMA ((ushort)0x0009) +#define CPM_CR_STOP_IDMA ((ushort)0x000b) + +#define mk_cr_cmd(PG, SBC, MCN, OP) \ + ((PG << 26) | (SBC << 21) | (MCN << 6) | OP) + +/* Dual Port RAM addresses. The first 16K is available for almost + * any CPM use, so we put the BDs there. The first 128 bytes are + * used for SMC1 and SMC2 parameter RAM, so we start allocating + * BDs above that. All of this must change when we start + * downloading RAM microcode. + */ +#define CPM_DATAONLY_BASE ((uint)128) +#define CPM_DP_NOSPACE ((uint)0x7fffffff) +#if defined(CONFIG_8272) || defined(CONFIG_MPC8555) +#define CPM_DATAONLY_SIZE ((uint)(8 * 1024) - CPM_DATAONLY_BASE) +#define CPM_FCC_SPECIAL_BASE ((uint)0x00009000) +#else +#define CPM_DATAONLY_SIZE ((uint)(16 * 1024) - CPM_DATAONLY_BASE) +#define CPM_FCC_SPECIAL_BASE ((uint)0x0000b000) +#endif + +/* The number of pages of host memory we allocate for CPM. This is + * done early in kernel initialization to get physically contiguous + * pages. + */ +#define NUM_CPM_HOST_PAGES 2 + +/* Export the base address of the communication processor registers + * and dual port ram. + */ +extern cpm_cpm2_t *cpmp; /* Pointer to comm processor */ + +extern unsigned long cpm_dpalloc(uint size, uint align); +extern int cpm_dpfree(unsigned long offset); +extern unsigned long cpm_dpalloc_fixed(unsigned long offset, uint size, uint align); +extern void cpm_dpdump(void); +extern void *cpm_dpram_addr(unsigned long offset); +extern void cpm_setbrg(uint brg, uint rate); +extern void cpm2_fastbrg(uint brg, uint rate, int div16); +extern void cpm2_reset(void); + + +/* Buffer descriptors used by many of the CPM protocols. +*/ +typedef struct cpm_buf_desc { + ushort cbd_sc; /* Status and Control */ + ushort cbd_datlen; /* Data length in buffer */ + uint cbd_bufaddr; /* Buffer address in host memory */ +} cbd_t; + +#define BD_SC_EMPTY ((ushort)0x8000) /* Receive is empty */ +#define BD_SC_READY ((ushort)0x8000) /* Transmit is ready */ +#define BD_SC_WRAP ((ushort)0x2000) /* Last buffer descriptor */ +#define BD_SC_INTRPT ((ushort)0x1000) /* Interrupt on change */ +#define BD_SC_LAST ((ushort)0x0800) /* Last buffer in frame */ +#define BD_SC_CM ((ushort)0x0200) /* Continous mode */ +#define BD_SC_ID ((ushort)0x0100) /* Rec'd too many idles */ +#define BD_SC_P ((ushort)0x0100) /* xmt preamble */ +#define BD_SC_BR ((ushort)0x0020) /* Break received */ +#define BD_SC_FR ((ushort)0x0010) /* Framing error */ +#define BD_SC_PR ((ushort)0x0008) /* Parity error */ +#define BD_SC_OV ((ushort)0x0002) /* Overrun */ +#define BD_SC_CD ((ushort)0x0001) /* ?? */ + +/* Function code bits, usually generic to devices. +*/ +#define CPMFCR_GBL ((u_char)0x20) /* Set memory snooping */ +#define CPMFCR_EB ((u_char)0x10) /* Set big endian byte order */ +#define CPMFCR_TC2 ((u_char)0x04) /* Transfer code 2 value */ +#define CPMFCR_DTB ((u_char)0x02) /* Use local bus for data when set */ +#define CPMFCR_BDB ((u_char)0x01) /* Use local bus for BD when set */ + +/* Parameter RAM offsets from the base. +*/ +#define PROFF_SCC1 ((uint)0x8000) +#define PROFF_SCC2 ((uint)0x8100) +#define PROFF_SCC3 ((uint)0x8200) +#define PROFF_SCC4 ((uint)0x8300) +#define PROFF_FCC1 ((uint)0x8400) +#define PROFF_FCC2 ((uint)0x8500) +#define PROFF_FCC3 ((uint)0x8600) +#define PROFF_MCC1 ((uint)0x8700) +#define PROFF_SMC1_BASE ((uint)0x87fc) +#define PROFF_IDMA1_BASE ((uint)0x87fe) +#define PROFF_MCC2 ((uint)0x8800) +#define PROFF_SMC2_BASE ((uint)0x88fc) +#define PROFF_IDMA2_BASE ((uint)0x88fe) +#define PROFF_SPI_BASE ((uint)0x89fc) +#define PROFF_IDMA3_BASE ((uint)0x89fe) +#define PROFF_TIMERS ((uint)0x8ae0) +#define PROFF_REVNUM ((uint)0x8af0) +#define PROFF_RAND ((uint)0x8af8) +#define PROFF_I2C_BASE ((uint)0x8afc) +#define PROFF_IDMA4_BASE ((uint)0x8afe) + +#define PROFF_SCC_SIZE ((uint)0x100) +#define PROFF_FCC_SIZE ((uint)0x100) +#define PROFF_SMC_SIZE ((uint)64) + +/* The SMCs are relocated to any of the first eight DPRAM pages. + * We will fix these at the first locations of DPRAM, until we + * get some microcode patches :-). + * The parameter ram space for the SMCs is fifty-some bytes, and + * they are required to start on a 64 byte boundary. + */ +#define PROFF_SMC1 (0) +#define PROFF_SMC2 (64) + + +/* Define enough so I can at least use the serial port as a UART. + */ +typedef struct smc_uart { + ushort smc_rbase; /* Rx Buffer descriptor base address */ + ushort smc_tbase; /* Tx Buffer descriptor base address */ + u_char smc_rfcr; /* Rx function code */ + u_char smc_tfcr; /* Tx function code */ + ushort smc_mrblr; /* Max receive buffer length */ + uint smc_rstate; /* Internal */ + uint smc_idp; /* Internal */ + ushort smc_rbptr; /* Internal */ + ushort smc_ibc; /* Internal */ + uint smc_rxtmp; /* Internal */ + uint smc_tstate; /* Internal */ + uint smc_tdp; /* Internal */ + ushort smc_tbptr; /* Internal */ + ushort smc_tbc; /* Internal */ + uint smc_txtmp; /* Internal */ + ushort smc_maxidl; /* Maximum idle characters */ + ushort smc_tmpidl; /* Temporary idle counter */ + ushort smc_brklen; /* Last received break length */ + ushort smc_brkec; /* rcv'd break condition counter */ + ushort smc_brkcr; /* xmt break count register */ + ushort smc_rmask; /* Temporary bit mask */ + uint smc_stmp; /* SDMA Temp */ +} smc_uart_t; + +/* SMC uart mode register (Internal memory map). +*/ +#define SMCMR_REN ((ushort)0x0001) +#define SMCMR_TEN ((ushort)0x0002) +#define SMCMR_DM ((ushort)0x000c) +#define SMCMR_SM_GCI ((ushort)0x0000) +#define SMCMR_SM_UART ((ushort)0x0020) +#define SMCMR_SM_TRANS ((ushort)0x0030) +#define SMCMR_SM_MASK ((ushort)0x0030) +#define SMCMR_PM_EVEN ((ushort)0x0100) /* Even parity, else odd */ +#define SMCMR_REVD SMCMR_PM_EVEN +#define SMCMR_PEN ((ushort)0x0200) /* Parity enable */ +#define SMCMR_BS SMCMR_PEN +#define SMCMR_SL ((ushort)0x0400) /* Two stops, else one */ +#define SMCR_CLEN_MASK ((ushort)0x7800) /* Character length */ +#define smcr_mk_clen(C) (((C) << 11) & SMCR_CLEN_MASK) + +/* SMC Event and Mask register. +*/ +#define SMCM_BRKE ((unsigned char)0x40) /* When in UART Mode */ +#define SMCM_BRK ((unsigned char)0x10) /* When in UART Mode */ +#define SMCM_TXE ((unsigned char)0x10) +#define SMCM_BSY ((unsigned char)0x04) +#define SMCM_TX ((unsigned char)0x02) +#define SMCM_RX ((unsigned char)0x01) + +/* Baud rate generators. +*/ +#define CPM_BRG_RST ((uint)0x00020000) +#define CPM_BRG_EN ((uint)0x00010000) +#define CPM_BRG_EXTC_INT ((uint)0x00000000) +#define CPM_BRG_EXTC_CLK3_9 ((uint)0x00004000) +#define CPM_BRG_EXTC_CLK5_15 ((uint)0x00008000) +#define CPM_BRG_ATB ((uint)0x00002000) +#define CPM_BRG_CD_MASK ((uint)0x00001ffe) +#define CPM_BRG_DIV16 ((uint)0x00000001) + +/* SCCs. +*/ +#define SCC_GSMRH_IRP ((uint)0x00040000) +#define SCC_GSMRH_GDE ((uint)0x00010000) +#define SCC_GSMRH_TCRC_CCITT ((uint)0x00008000) +#define SCC_GSMRH_TCRC_BISYNC ((uint)0x00004000) +#define SCC_GSMRH_TCRC_HDLC ((uint)0x00000000) +#define SCC_GSMRH_REVD ((uint)0x00002000) +#define SCC_GSMRH_TRX ((uint)0x00001000) +#define SCC_GSMRH_TTX ((uint)0x00000800) +#define SCC_GSMRH_CDP ((uint)0x00000400) +#define SCC_GSMRH_CTSP ((uint)0x00000200) +#define SCC_GSMRH_CDS ((uint)0x00000100) +#define SCC_GSMRH_CTSS ((uint)0x00000080) +#define SCC_GSMRH_TFL ((uint)0x00000040) +#define SCC_GSMRH_RFW ((uint)0x00000020) +#define SCC_GSMRH_TXSY ((uint)0x00000010) +#define SCC_GSMRH_SYNL16 ((uint)0x0000000c) +#define SCC_GSMRH_SYNL8 ((uint)0x00000008) +#define SCC_GSMRH_SYNL4 ((uint)0x00000004) +#define SCC_GSMRH_RTSM ((uint)0x00000002) +#define SCC_GSMRH_RSYN ((uint)0x00000001) + +#define SCC_GSMRL_SIR ((uint)0x80000000) /* SCC2 only */ +#define SCC_GSMRL_EDGE_NONE ((uint)0x60000000) +#define SCC_GSMRL_EDGE_NEG ((uint)0x40000000) +#define SCC_GSMRL_EDGE_POS ((uint)0x20000000) +#define SCC_GSMRL_EDGE_BOTH ((uint)0x00000000) +#define SCC_GSMRL_TCI ((uint)0x10000000) +#define SCC_GSMRL_TSNC_3 ((uint)0x0c000000) +#define SCC_GSMRL_TSNC_4 ((uint)0x08000000) +#define SCC_GSMRL_TSNC_14 ((uint)0x04000000) +#define SCC_GSMRL_TSNC_INF ((uint)0x00000000) +#define SCC_GSMRL_RINV ((uint)0x02000000) +#define SCC_GSMRL_TINV ((uint)0x01000000) +#define SCC_GSMRL_TPL_128 ((uint)0x00c00000) +#define SCC_GSMRL_TPL_64 ((uint)0x00a00000) +#define SCC_GSMRL_TPL_48 ((uint)0x00800000) +#define SCC_GSMRL_TPL_32 ((uint)0x00600000) +#define SCC_GSMRL_TPL_16 ((uint)0x00400000) +#define SCC_GSMRL_TPL_8 ((uint)0x00200000) +#define SCC_GSMRL_TPL_NONE ((uint)0x00000000) +#define SCC_GSMRL_TPP_ALL1 ((uint)0x00180000) +#define SCC_GSMRL_TPP_01 ((uint)0x00100000) +#define SCC_GSMRL_TPP_10 ((uint)0x00080000) +#define SCC_GSMRL_TPP_ZEROS ((uint)0x00000000) +#define SCC_GSMRL_TEND ((uint)0x00040000) +#define SCC_GSMRL_TDCR_32 ((uint)0x00030000) +#define SCC_GSMRL_TDCR_16 ((uint)0x00020000) +#define SCC_GSMRL_TDCR_8 ((uint)0x00010000) +#define SCC_GSMRL_TDCR_1 ((uint)0x00000000) +#define SCC_GSMRL_RDCR_32 ((uint)0x0000c000) +#define SCC_GSMRL_RDCR_16 ((uint)0x00008000) +#define SCC_GSMRL_RDCR_8 ((uint)0x00004000) +#define SCC_GSMRL_RDCR_1 ((uint)0x00000000) +#define SCC_GSMRL_RENC_DFMAN ((uint)0x00003000) +#define SCC_GSMRL_RENC_MANCH ((uint)0x00002000) +#define SCC_GSMRL_RENC_FM0 ((uint)0x00001000) +#define SCC_GSMRL_RENC_NRZI ((uint)0x00000800) +#define SCC_GSMRL_RENC_NRZ ((uint)0x00000000) +#define SCC_GSMRL_TENC_DFMAN ((uint)0x00000600) +#define SCC_GSMRL_TENC_MANCH ((uint)0x00000400) +#define SCC_GSMRL_TENC_FM0 ((uint)0x00000200) +#define SCC_GSMRL_TENC_NRZI ((uint)0x00000100) +#define SCC_GSMRL_TENC_NRZ ((uint)0x00000000) +#define SCC_GSMRL_DIAG_LE ((uint)0x000000c0) /* Loop and echo */ +#define SCC_GSMRL_DIAG_ECHO ((uint)0x00000080) +#define SCC_GSMRL_DIAG_LOOP ((uint)0x00000040) +#define SCC_GSMRL_DIAG_NORM ((uint)0x00000000) +#define SCC_GSMRL_ENR ((uint)0x00000020) +#define SCC_GSMRL_ENT ((uint)0x00000010) +#define SCC_GSMRL_MODE_ENET ((uint)0x0000000c) +#define SCC_GSMRL_MODE_DDCMP ((uint)0x00000009) +#define SCC_GSMRL_MODE_BISYNC ((uint)0x00000008) +#define SCC_GSMRL_MODE_V14 ((uint)0x00000007) +#define SCC_GSMRL_MODE_AHDLC ((uint)0x00000006) +#define SCC_GSMRL_MODE_PROFIBUS ((uint)0x00000005) +#define SCC_GSMRL_MODE_UART ((uint)0x00000004) +#define SCC_GSMRL_MODE_SS7 ((uint)0x00000003) +#define SCC_GSMRL_MODE_ATALK ((uint)0x00000002) +#define SCC_GSMRL_MODE_HDLC ((uint)0x00000000) + +#define SCC_TODR_TOD ((ushort)0x8000) + +/* SCC Event and Mask register. +*/ +#define SCCM_TXE ((unsigned char)0x10) +#define SCCM_BSY ((unsigned char)0x04) +#define SCCM_TX ((unsigned char)0x02) +#define SCCM_RX ((unsigned char)0x01) + +typedef struct scc_param { + ushort scc_rbase; /* Rx Buffer descriptor base address */ + ushort scc_tbase; /* Tx Buffer descriptor base address */ + u_char scc_rfcr; /* Rx function code */ + u_char scc_tfcr; /* Tx function code */ + ushort scc_mrblr; /* Max receive buffer length */ + uint scc_rstate; /* Internal */ + uint scc_idp; /* Internal */ + ushort scc_rbptr; /* Internal */ + ushort scc_ibc; /* Internal */ + uint scc_rxtmp; /* Internal */ + uint scc_tstate; /* Internal */ + uint scc_tdp; /* Internal */ + ushort scc_tbptr; /* Internal */ + ushort scc_tbc; /* Internal */ + uint scc_txtmp; /* Internal */ + uint scc_rcrc; /* Internal */ + uint scc_tcrc; /* Internal */ +} sccp_t; + +/* CPM Ethernet through SCC1. + */ +typedef struct scc_enet { + sccp_t sen_genscc; + uint sen_cpres; /* Preset CRC */ + uint sen_cmask; /* Constant mask for CRC */ + uint sen_crcec; /* CRC Error counter */ + uint sen_alec; /* alignment error counter */ + uint sen_disfc; /* discard frame counter */ + ushort sen_pads; /* Tx short frame pad character */ + ushort sen_retlim; /* Retry limit threshold */ + ushort sen_retcnt; /* Retry limit counter */ + ushort sen_maxflr; /* maximum frame length register */ + ushort sen_minflr; /* minimum frame length register */ + ushort sen_maxd1; /* maximum DMA1 length */ + ushort sen_maxd2; /* maximum DMA2 length */ + ushort sen_maxd; /* Rx max DMA */ + ushort sen_dmacnt; /* Rx DMA counter */ + ushort sen_maxb; /* Max BD byte count */ + ushort sen_gaddr1; /* Group address filter */ + ushort sen_gaddr2; + ushort sen_gaddr3; + ushort sen_gaddr4; + uint sen_tbuf0data0; /* Save area 0 - current frame */ + uint sen_tbuf0data1; /* Save area 1 - current frame */ + uint sen_tbuf0rba; /* Internal */ + uint sen_tbuf0crc; /* Internal */ + ushort sen_tbuf0bcnt; /* Internal */ + ushort sen_paddrh; /* physical address (MSB) */ + ushort sen_paddrm; + ushort sen_paddrl; /* physical address (LSB) */ + ushort sen_pper; /* persistence */ + ushort sen_rfbdptr; /* Rx first BD pointer */ + ushort sen_tfbdptr; /* Tx first BD pointer */ + ushort sen_tlbdptr; /* Tx last BD pointer */ + uint sen_tbuf1data0; /* Save area 0 - current frame */ + uint sen_tbuf1data1; /* Save area 1 - current frame */ + uint sen_tbuf1rba; /* Internal */ + uint sen_tbuf1crc; /* Internal */ + ushort sen_tbuf1bcnt; /* Internal */ + ushort sen_txlen; /* Tx Frame length counter */ + ushort sen_iaddr1; /* Individual address filter */ + ushort sen_iaddr2; + ushort sen_iaddr3; + ushort sen_iaddr4; + ushort sen_boffcnt; /* Backoff counter */ + + /* NOTE: Some versions of the manual have the following items + * incorrectly documented. Below is the proper order. + */ + ushort sen_taddrh; /* temp address (MSB) */ + ushort sen_taddrm; + ushort sen_taddrl; /* temp address (LSB) */ +} scc_enet_t; + + +/* SCC Event register as used by Ethernet. +*/ +#define SCCE_ENET_GRA ((ushort)0x0080) /* Graceful stop complete */ +#define SCCE_ENET_TXE ((ushort)0x0010) /* Transmit Error */ +#define SCCE_ENET_RXF ((ushort)0x0008) /* Full frame received */ +#define SCCE_ENET_BSY ((ushort)0x0004) /* All incoming buffers full */ +#define SCCE_ENET_TXB ((ushort)0x0002) /* A buffer was transmitted */ +#define SCCE_ENET_RXB ((ushort)0x0001) /* A buffer was received */ + +/* SCC Mode Register (PSMR) as used by Ethernet. +*/ +#define SCC_PSMR_HBC ((ushort)0x8000) /* Enable heartbeat */ +#define SCC_PSMR_FC ((ushort)0x4000) /* Force collision */ +#define SCC_PSMR_RSH ((ushort)0x2000) /* Receive short frames */ +#define SCC_PSMR_IAM ((ushort)0x1000) /* Check individual hash */ +#define SCC_PSMR_ENCRC ((ushort)0x0800) /* Ethernet CRC mode */ +#define SCC_PSMR_PRO ((ushort)0x0200) /* Promiscuous mode */ +#define SCC_PSMR_BRO ((ushort)0x0100) /* Catch broadcast pkts */ +#define SCC_PSMR_SBT ((ushort)0x0080) /* Special backoff timer */ +#define SCC_PSMR_LPB ((ushort)0x0040) /* Set Loopback mode */ +#define SCC_PSMR_SIP ((ushort)0x0020) /* Sample Input Pins */ +#define SCC_PSMR_LCW ((ushort)0x0010) /* Late collision window */ +#define SCC_PSMR_NIB22 ((ushort)0x000a) /* Start frame search */ +#define SCC_PSMR_FDE ((ushort)0x0001) /* Full duplex enable */ + +/* Buffer descriptor control/status used by Ethernet receive. + * Common to SCC and FCC. + */ +#define BD_ENET_RX_EMPTY ((ushort)0x8000) +#define BD_ENET_RX_WRAP ((ushort)0x2000) +#define BD_ENET_RX_INTR ((ushort)0x1000) +#define BD_ENET_RX_LAST ((ushort)0x0800) +#define BD_ENET_RX_FIRST ((ushort)0x0400) +#define BD_ENET_RX_MISS ((ushort)0x0100) +#define BD_ENET_RX_BC ((ushort)0x0080) /* FCC Only */ +#define BD_ENET_RX_MC ((ushort)0x0040) /* FCC Only */ +#define BD_ENET_RX_LG ((ushort)0x0020) +#define BD_ENET_RX_NO ((ushort)0x0010) +#define BD_ENET_RX_SH ((ushort)0x0008) +#define BD_ENET_RX_CR ((ushort)0x0004) +#define BD_ENET_RX_OV ((ushort)0x0002) +#define BD_ENET_RX_CL ((ushort)0x0001) +#define BD_ENET_RX_STATS ((ushort)0x01ff) /* All status bits */ + +/* Buffer descriptor control/status used by Ethernet transmit. + * Common to SCC and FCC. + */ +#define BD_ENET_TX_READY ((ushort)0x8000) +#define BD_ENET_TX_PAD ((ushort)0x4000) +#define BD_ENET_TX_WRAP ((ushort)0x2000) +#define BD_ENET_TX_INTR ((ushort)0x1000) +#define BD_ENET_TX_LAST ((ushort)0x0800) +#define BD_ENET_TX_TC ((ushort)0x0400) +#define BD_ENET_TX_DEF ((ushort)0x0200) +#define BD_ENET_TX_HB ((ushort)0x0100) +#define BD_ENET_TX_LC ((ushort)0x0080) +#define BD_ENET_TX_RL ((ushort)0x0040) +#define BD_ENET_TX_RCMASK ((ushort)0x003c) +#define BD_ENET_TX_UN ((ushort)0x0002) +#define BD_ENET_TX_CSL ((ushort)0x0001) +#define BD_ENET_TX_STATS ((ushort)0x03ff) /* All status bits */ + +/* SCC as UART +*/ +typedef struct scc_uart { + sccp_t scc_genscc; + uint scc_res1; /* Reserved */ + uint scc_res2; /* Reserved */ + ushort scc_maxidl; /* Maximum idle chars */ + ushort scc_idlc; /* temp idle counter */ + ushort scc_brkcr; /* Break count register */ + ushort scc_parec; /* receive parity error counter */ + ushort scc_frmec; /* receive framing error counter */ + ushort scc_nosec; /* receive noise counter */ + ushort scc_brkec; /* receive break condition counter */ + ushort scc_brkln; /* last received break length */ + ushort scc_uaddr1; /* UART address character 1 */ + ushort scc_uaddr2; /* UART address character 2 */ + ushort scc_rtemp; /* Temp storage */ + ushort scc_toseq; /* Transmit out of sequence char */ + ushort scc_char1; /* control character 1 */ + ushort scc_char2; /* control character 2 */ + ushort scc_char3; /* control character 3 */ + ushort scc_char4; /* control character 4 */ + ushort scc_char5; /* control character 5 */ + ushort scc_char6; /* control character 6 */ + ushort scc_char7; /* control character 7 */ + ushort scc_char8; /* control character 8 */ + ushort scc_rccm; /* receive control character mask */ + ushort scc_rccr; /* receive control character register */ + ushort scc_rlbc; /* receive last break character */ +} scc_uart_t; + +/* SCC Event and Mask registers when it is used as a UART. +*/ +#define UART_SCCM_GLR ((ushort)0x1000) +#define UART_SCCM_GLT ((ushort)0x0800) +#define UART_SCCM_AB ((ushort)0x0200) +#define UART_SCCM_IDL ((ushort)0x0100) +#define UART_SCCM_GRA ((ushort)0x0080) +#define UART_SCCM_BRKE ((ushort)0x0040) +#define UART_SCCM_BRKS ((ushort)0x0020) +#define UART_SCCM_CCR ((ushort)0x0008) +#define UART_SCCM_BSY ((ushort)0x0004) +#define UART_SCCM_TX ((ushort)0x0002) +#define UART_SCCM_RX ((ushort)0x0001) + +/* The SCC PSMR when used as a UART. +*/ +#define SCU_PSMR_FLC ((ushort)0x8000) +#define SCU_PSMR_SL ((ushort)0x4000) +#define SCU_PSMR_CL ((ushort)0x3000) +#define SCU_PSMR_UM ((ushort)0x0c00) +#define SCU_PSMR_FRZ ((ushort)0x0200) +#define SCU_PSMR_RZS ((ushort)0x0100) +#define SCU_PSMR_SYN ((ushort)0x0080) +#define SCU_PSMR_DRT ((ushort)0x0040) +#define SCU_PSMR_PEN ((ushort)0x0010) +#define SCU_PSMR_RPM ((ushort)0x000c) +#define SCU_PSMR_REVP ((ushort)0x0008) +#define SCU_PSMR_TPM ((ushort)0x0003) +#define SCU_PSMR_TEVP ((ushort)0x0002) + +/* CPM Transparent mode SCC. + */ +typedef struct scc_trans { + sccp_t st_genscc; + uint st_cpres; /* Preset CRC */ + uint st_cmask; /* Constant mask for CRC */ +} scc_trans_t; + +#define BD_SCC_TX_LAST ((ushort)0x0800) + +/* How about some FCCs..... +*/ +#define FCC_GFMR_DIAG_NORM ((uint)0x00000000) +#define FCC_GFMR_DIAG_LE ((uint)0x40000000) +#define FCC_GFMR_DIAG_AE ((uint)0x80000000) +#define FCC_GFMR_DIAG_ALE ((uint)0xc0000000) +#define FCC_GFMR_TCI ((uint)0x20000000) +#define FCC_GFMR_TRX ((uint)0x10000000) +#define FCC_GFMR_TTX ((uint)0x08000000) +#define FCC_GFMR_TTX ((uint)0x08000000) +#define FCC_GFMR_CDP ((uint)0x04000000) +#define FCC_GFMR_CTSP ((uint)0x02000000) +#define FCC_GFMR_CDS ((uint)0x01000000) +#define FCC_GFMR_CTSS ((uint)0x00800000) +#define FCC_GFMR_SYNL_NONE ((uint)0x00000000) +#define FCC_GFMR_SYNL_AUTO ((uint)0x00004000) +#define FCC_GFMR_SYNL_8 ((uint)0x00008000) +#define FCC_GFMR_SYNL_16 ((uint)0x0000c000) +#define FCC_GFMR_RTSM ((uint)0x00002000) +#define FCC_GFMR_RENC_NRZ ((uint)0x00000000) +#define FCC_GFMR_RENC_NRZI ((uint)0x00000800) +#define FCC_GFMR_REVD ((uint)0x00000400) +#define FCC_GFMR_TENC_NRZ ((uint)0x00000000) +#define FCC_GFMR_TENC_NRZI ((uint)0x00000100) +#define FCC_GFMR_TCRC_16 ((uint)0x00000000) +#define FCC_GFMR_TCRC_32 ((uint)0x00000080) +#define FCC_GFMR_ENR ((uint)0x00000020) +#define FCC_GFMR_ENT ((uint)0x00000010) +#define FCC_GFMR_MODE_ENET ((uint)0x0000000c) +#define FCC_GFMR_MODE_ATM ((uint)0x0000000a) +#define FCC_GFMR_MODE_HDLC ((uint)0x00000000) + +/* Generic FCC parameter ram. +*/ +typedef struct fcc_param { + ushort fcc_riptr; /* Rx Internal temp pointer */ + ushort fcc_tiptr; /* Tx Internal temp pointer */ + ushort fcc_res1; + ushort fcc_mrblr; /* Max receive buffer length, mod 32 bytes */ + uint fcc_rstate; /* Upper byte is Func code, must be set */ + uint fcc_rbase; /* Receive BD base */ + ushort fcc_rbdstat; /* RxBD status */ + ushort fcc_rbdlen; /* RxBD down counter */ + uint fcc_rdptr; /* RxBD internal data pointer */ + uint fcc_tstate; /* Upper byte is Func code, must be set */ + uint fcc_tbase; /* Transmit BD base */ + ushort fcc_tbdstat; /* TxBD status */ + ushort fcc_tbdlen; /* TxBD down counter */ + uint fcc_tdptr; /* TxBD internal data pointer */ + uint fcc_rbptr; /* Rx BD Internal buf pointer */ + uint fcc_tbptr; /* Tx BD Internal buf pointer */ + uint fcc_rcrc; /* Rx temp CRC */ + uint fcc_res2; + uint fcc_tcrc; /* Tx temp CRC */ +} fccp_t; + + +/* Ethernet controller through FCC. +*/ +typedef struct fcc_enet { + fccp_t fen_genfcc; + uint fen_statbuf; /* Internal status buffer */ + uint fen_camptr; /* CAM address */ + uint fen_cmask; /* Constant mask for CRC */ + uint fen_cpres; /* Preset CRC */ + uint fen_crcec; /* CRC Error counter */ + uint fen_alec; /* alignment error counter */ + uint fen_disfc; /* discard frame counter */ + ushort fen_retlim; /* Retry limit */ + ushort fen_retcnt; /* Retry counter */ + ushort fen_pper; /* Persistence */ + ushort fen_boffcnt; /* backoff counter */ + uint fen_gaddrh; /* Group address filter, high 32-bits */ + uint fen_gaddrl; /* Group address filter, low 32-bits */ + ushort fen_tfcstat; /* out of sequence TxBD */ + ushort fen_tfclen; + uint fen_tfcptr; + ushort fen_mflr; /* Maximum frame length (1518) */ + ushort fen_paddrh; /* MAC address */ + ushort fen_paddrm; + ushort fen_paddrl; + ushort fen_ibdcount; /* Internal BD counter */ + ushort fen_ibdstart; /* Internal BD start pointer */ + ushort fen_ibdend; /* Internal BD end pointer */ + ushort fen_txlen; /* Internal Tx frame length counter */ + uint fen_ibdbase[8]; /* Internal use */ + uint fen_iaddrh; /* Individual address filter */ + uint fen_iaddrl; + ushort fen_minflr; /* Minimum frame length (64) */ + ushort fen_taddrh; /* Filter transfer MAC address */ + ushort fen_taddrm; + ushort fen_taddrl; + ushort fen_padptr; /* Pointer to pad byte buffer */ + ushort fen_cftype; /* control frame type */ + ushort fen_cfrange; /* control frame range */ + ushort fen_maxb; /* maximum BD count */ + ushort fen_maxd1; /* Max DMA1 length (1520) */ + ushort fen_maxd2; /* Max DMA2 length (1520) */ + ushort fen_maxd; /* internal max DMA count */ + ushort fen_dmacnt; /* internal DMA counter */ + uint fen_octc; /* Total octect counter */ + uint fen_colc; /* Total collision counter */ + uint fen_broc; /* Total broadcast packet counter */ + uint fen_mulc; /* Total multicast packet count */ + uint fen_uspc; /* Total packets < 64 bytes */ + uint fen_frgc; /* Total packets < 64 bytes with errors */ + uint fen_ospc; /* Total packets > 1518 */ + uint fen_jbrc; /* Total packets > 1518 with errors */ + uint fen_p64c; /* Total packets == 64 bytes */ + uint fen_p65c; /* Total packets 64 < bytes <= 127 */ + uint fen_p128c; /* Total packets 127 < bytes <= 255 */ + uint fen_p256c; /* Total packets 256 < bytes <= 511 */ + uint fen_p512c; /* Total packets 512 < bytes <= 1023 */ + uint fen_p1024c; /* Total packets 1024 < bytes <= 1518 */ + uint fen_cambuf; /* Internal CAM buffer poiner */ + ushort fen_rfthr; /* Received frames threshold */ + ushort fen_rfcnt; /* Received frames count */ +} fcc_enet_t; + +/* FCC Event/Mask register as used by Ethernet. +*/ +#define FCC_ENET_GRA ((ushort)0x0080) /* Graceful stop complete */ +#define FCC_ENET_RXC ((ushort)0x0040) /* Control Frame Received */ +#define FCC_ENET_TXC ((ushort)0x0020) /* Out of seq. Tx sent */ +#define FCC_ENET_TXE ((ushort)0x0010) /* Transmit Error */ +#define FCC_ENET_RXF ((ushort)0x0008) /* Full frame received */ +#define FCC_ENET_BSY ((ushort)0x0004) /* Busy. Rx Frame dropped */ +#define FCC_ENET_TXB ((ushort)0x0002) /* A buffer was transmitted */ +#define FCC_ENET_RXB ((ushort)0x0001) /* A buffer was received */ + +/* FCC Mode Register (FPSMR) as used by Ethernet. +*/ +#define FCC_PSMR_HBC ((uint)0x80000000) /* Enable heartbeat */ +#define FCC_PSMR_FC ((uint)0x40000000) /* Force Collision */ +#define FCC_PSMR_SBT ((uint)0x20000000) /* Stop backoff timer */ +#define FCC_PSMR_LPB ((uint)0x10000000) /* Local protect. 1 = FDX */ +#define FCC_PSMR_LCW ((uint)0x08000000) /* Late collision select */ +#define FCC_PSMR_FDE ((uint)0x04000000) /* Full Duplex Enable */ +#define FCC_PSMR_MON ((uint)0x02000000) /* RMON Enable */ +#define FCC_PSMR_PRO ((uint)0x00400000) /* Promiscuous Enable */ +#define FCC_PSMR_FCE ((uint)0x00200000) /* Flow Control Enable */ +#define FCC_PSMR_RSH ((uint)0x00100000) /* Receive Short Frames */ +#define FCC_PSMR_CAM ((uint)0x00000400) /* CAM enable */ +#define FCC_PSMR_BRO ((uint)0x00000200) /* Broadcast pkt discard */ +#define FCC_PSMR_ENCRC ((uint)0x00000080) /* Use 32-bit CRC */ + +/* IIC parameter RAM. +*/ +typedef struct iic { + ushort iic_rbase; /* Rx Buffer descriptor base address */ + ushort iic_tbase; /* Tx Buffer descriptor base address */ + u_char iic_rfcr; /* Rx function code */ + u_char iic_tfcr; /* Tx function code */ + ushort iic_mrblr; /* Max receive buffer length */ + uint iic_rstate; /* Internal */ + uint iic_rdp; /* Internal */ + ushort iic_rbptr; /* Internal */ + ushort iic_rbc; /* Internal */ + uint iic_rxtmp; /* Internal */ + uint iic_tstate; /* Internal */ + uint iic_tdp; /* Internal */ + ushort iic_tbptr; /* Internal */ + ushort iic_tbc; /* Internal */ + uint iic_txtmp; /* Internal */ +} iic_t; + +/* SPI parameter RAM. +*/ +typedef struct spi { + ushort spi_rbase; /* Rx Buffer descriptor base address */ + ushort spi_tbase; /* Tx Buffer descriptor base address */ + u_char spi_rfcr; /* Rx function code */ + u_char spi_tfcr; /* Tx function code */ + ushort spi_mrblr; /* Max receive buffer length */ + uint spi_rstate; /* Internal */ + uint spi_rdp; /* Internal */ + ushort spi_rbptr; /* Internal */ + ushort spi_rbc; /* Internal */ + uint spi_rxtmp; /* Internal */ + uint spi_tstate; /* Internal */ + uint spi_tdp; /* Internal */ + ushort spi_tbptr; /* Internal */ + ushort spi_tbc; /* Internal */ + uint spi_txtmp; /* Internal */ + uint spi_res; /* Tx temp. */ + uint spi_res1[4]; /* SDMA temp. */ +} spi_t; + +/* SPI Mode register. +*/ +#define SPMODE_LOOP ((ushort)0x4000) /* Loopback */ +#define SPMODE_CI ((ushort)0x2000) /* Clock Invert */ +#define SPMODE_CP ((ushort)0x1000) /* Clock Phase */ +#define SPMODE_DIV16 ((ushort)0x0800) /* BRG/16 mode */ +#define SPMODE_REV ((ushort)0x0400) /* Reversed Data */ +#define SPMODE_MSTR ((ushort)0x0200) /* SPI Master */ +#define SPMODE_EN ((ushort)0x0100) /* Enable */ +#define SPMODE_LENMSK ((ushort)0x00f0) /* character length */ +#define SPMODE_PMMSK ((ushort)0x000f) /* prescale modulus */ + +#define SPMODE_LEN(x) ((((x)-1)&0xF)<<4) +#define SPMODE_PM(x) ((x) &0xF) + +#define SPI_EB ((u_char)0x10) /* big endian byte order */ + +#define BD_IIC_START ((ushort)0x0400) + +/* IDMA parameter RAM +*/ +typedef struct idma { + ushort ibase; /* IDMA buffer descriptor table base address */ + ushort dcm; /* DMA channel mode */ + ushort ibdptr; /* IDMA current buffer descriptor pointer */ + ushort dpr_buf; /* IDMA transfer buffer base address */ + ushort buf_inv; /* internal buffer inventory */ + ushort ss_max; /* steady-state maximum transfer size */ + ushort dpr_in_ptr; /* write pointer inside the internal buffer */ + ushort sts; /* source transfer size */ + ushort dpr_out_ptr; /* read pointer inside the internal buffer */ + ushort seob; /* source end of burst */ + ushort deob; /* destination end of burst */ + ushort dts; /* destination transfer size */ + ushort ret_add; /* return address when working in ERM=1 mode */ + ushort res0; /* reserved */ + uint bd_cnt; /* internal byte count */ + uint s_ptr; /* source internal data pointer */ + uint d_ptr; /* destination internal data pointer */ + uint istate; /* internal state */ + u_char res1[20]; /* pad to 64-byte length */ +} idma_t; + +/* DMA channel mode bit fields +*/ +#define IDMA_DCM_FB ((ushort)0x8000) /* fly-by mode */ +#define IDMA_DCM_LP ((ushort)0x4000) /* low priority */ +#define IDMA_DCM_TC2 ((ushort)0x0400) /* value driven on TC[2] */ +#define IDMA_DCM_DMA_WRAP_MASK ((ushort)0x01c0) /* mask for DMA wrap */ +#define IDMA_DCM_DMA_WRAP_64 ((ushort)0x0000) /* 64-byte DMA xfer buffer */ +#define IDMA_DCM_DMA_WRAP_128 ((ushort)0x0040) /* 128-byte DMA xfer buffer */ +#define IDMA_DCM_DMA_WRAP_256 ((ushort)0x0080) /* 256-byte DMA xfer buffer */ +#define IDMA_DCM_DMA_WRAP_512 ((ushort)0x00c0) /* 512-byte DMA xfer buffer */ +#define IDMA_DCM_DMA_WRAP_1024 ((ushort)0x0100) /* 1024-byte DMA xfer buffer */ +#define IDMA_DCM_DMA_WRAP_2048 ((ushort)0x0140) /* 2048-byte DMA xfer buffer */ +#define IDMA_DCM_SINC ((ushort)0x0020) /* source inc addr */ +#define IDMA_DCM_DINC ((ushort)0x0010) /* destination inc addr */ +#define IDMA_DCM_ERM ((ushort)0x0008) /* external request mode */ +#define IDMA_DCM_DT ((ushort)0x0004) /* DONE treatment */ +#define IDMA_DCM_SD_MASK ((ushort)0x0003) /* mask for SD bit field */ +#define IDMA_DCM_SD_MEM2MEM ((ushort)0x0000) /* memory-to-memory xfer */ +#define IDMA_DCM_SD_PER2MEM ((ushort)0x0002) /* peripheral-to-memory xfer */ +#define IDMA_DCM_SD_MEM2PER ((ushort)0x0001) /* memory-to-peripheral xfer */ + +/* IDMA Buffer Descriptors +*/ +typedef struct idma_bd { + uint flags; + uint len; /* data length */ + uint src; /* source data buffer pointer */ + uint dst; /* destination data buffer pointer */ +} idma_bd_t; + +/* IDMA buffer descriptor flag bit fields +*/ +#define IDMA_BD_V ((uint)0x80000000) /* valid */ +#define IDMA_BD_W ((uint)0x20000000) /* wrap */ +#define IDMA_BD_I ((uint)0x10000000) /* interrupt */ +#define IDMA_BD_L ((uint)0x08000000) /* last */ +#define IDMA_BD_CM ((uint)0x02000000) /* continuous mode */ +#define IDMA_BD_SDN ((uint)0x00400000) /* source done */ +#define IDMA_BD_DDN ((uint)0x00200000) /* destination done */ +#define IDMA_BD_DGBL ((uint)0x00100000) /* destination global */ +#define IDMA_BD_DBO_LE ((uint)0x00040000) /* little-end dest byte order */ +#define IDMA_BD_DBO_BE ((uint)0x00080000) /* big-end dest byte order */ +#define IDMA_BD_DDTB ((uint)0x00010000) /* destination data bus */ +#define IDMA_BD_SGBL ((uint)0x00002000) /* source global */ +#define IDMA_BD_SBO_LE ((uint)0x00000800) /* little-end src byte order */ +#define IDMA_BD_SBO_BE ((uint)0x00001000) /* big-end src byte order */ +#define IDMA_BD_SDTB ((uint)0x00000200) /* source data bus */ + +/* per-channel IDMA registers +*/ +typedef struct im_idma { + u_char idsr; /* IDMAn event status register */ + u_char res0[3]; + u_char idmr; /* IDMAn event mask register */ + u_char res1[3]; +} im_idma_t; + +/* IDMA event register bit fields +*/ +#define IDMA_EVENT_SC ((unsigned char)0x08) /* stop completed */ +#define IDMA_EVENT_OB ((unsigned char)0x04) /* out of buffers */ +#define IDMA_EVENT_EDN ((unsigned char)0x02) /* external DONE asserted */ +#define IDMA_EVENT_BC ((unsigned char)0x01) /* buffer descriptor complete */ + +/* RISC Controller Configuration Register (RCCR) bit fields +*/ +#define RCCR_TIME ((uint)0x80000000) /* timer enable */ +#define RCCR_TIMEP_MASK ((uint)0x3f000000) /* mask for timer period bit field */ +#define RCCR_DR0M ((uint)0x00800000) /* IDMA0 request mode */ +#define RCCR_DR1M ((uint)0x00400000) /* IDMA1 request mode */ +#define RCCR_DR2M ((uint)0x00000080) /* IDMA2 request mode */ +#define RCCR_DR3M ((uint)0x00000040) /* IDMA3 request mode */ +#define RCCR_DR0QP_MASK ((uint)0x00300000) /* mask for IDMA0 req priority */ +#define RCCR_DR0QP_HIGH ((uint)0x00000000) /* IDMA0 has high req priority */ +#define RCCR_DR0QP_MED ((uint)0x00100000) /* IDMA0 has medium req priority */ +#define RCCR_DR0QP_LOW ((uint)0x00200000) /* IDMA0 has low req priority */ +#define RCCR_DR1QP_MASK ((uint)0x00030000) /* mask for IDMA1 req priority */ +#define RCCR_DR1QP_HIGH ((uint)0x00000000) /* IDMA1 has high req priority */ +#define RCCR_DR1QP_MED ((uint)0x00010000) /* IDMA1 has medium req priority */ +#define RCCR_DR1QP_LOW ((uint)0x00020000) /* IDMA1 has low req priority */ +#define RCCR_DR2QP_MASK ((uint)0x00000030) /* mask for IDMA2 req priority */ +#define RCCR_DR2QP_HIGH ((uint)0x00000000) /* IDMA2 has high req priority */ +#define RCCR_DR2QP_MED ((uint)0x00000010) /* IDMA2 has medium req priority */ +#define RCCR_DR2QP_LOW ((uint)0x00000020) /* IDMA2 has low req priority */ +#define RCCR_DR3QP_MASK ((uint)0x00000003) /* mask for IDMA3 req priority */ +#define RCCR_DR3QP_HIGH ((uint)0x00000000) /* IDMA3 has high req priority */ +#define RCCR_DR3QP_MED ((uint)0x00000001) /* IDMA3 has medium req priority */ +#define RCCR_DR3QP_LOW ((uint)0x00000002) /* IDMA3 has low req priority */ +#define RCCR_EIE ((uint)0x00080000) /* external interrupt enable */ +#define RCCR_SCD ((uint)0x00040000) /* scheduler configuration */ +#define RCCR_ERAM_MASK ((uint)0x0000e000) /* mask for enable RAM microcode */ +#define RCCR_ERAM_0KB ((uint)0x00000000) /* use 0KB of dpram for microcode */ +#define RCCR_ERAM_2KB ((uint)0x00002000) /* use 2KB of dpram for microcode */ +#define RCCR_ERAM_4KB ((uint)0x00004000) /* use 4KB of dpram for microcode */ +#define RCCR_ERAM_6KB ((uint)0x00006000) /* use 6KB of dpram for microcode */ +#define RCCR_ERAM_8KB ((uint)0x00008000) /* use 8KB of dpram for microcode */ +#define RCCR_ERAM_10KB ((uint)0x0000a000) /* use 10KB of dpram for microcode */ +#define RCCR_ERAM_12KB ((uint)0x0000c000) /* use 12KB of dpram for microcode */ +#define RCCR_EDM0 ((uint)0x00000800) /* DREQ0 edge detect mode */ +#define RCCR_EDM1 ((uint)0x00000400) /* DREQ1 edge detect mode */ +#define RCCR_EDM2 ((uint)0x00000200) /* DREQ2 edge detect mode */ +#define RCCR_EDM3 ((uint)0x00000100) /* DREQ3 edge detect mode */ +#define RCCR_DEM01 ((uint)0x00000008) /* DONE0/DONE1 edge detect mode */ +#define RCCR_DEM23 ((uint)0x00000004) /* DONE2/DONE3 edge detect mode */ + +/*----------------------------------------------------------------------- + * CMXFCR - CMX FCC Clock Route Register + */ +#define CMXFCR_FC1 0x40000000 /* FCC1 connection */ +#define CMXFCR_RF1CS_MSK 0x38000000 /* Receive FCC1 Clock Source Mask */ +#define CMXFCR_TF1CS_MSK 0x07000000 /* Transmit FCC1 Clock Source Mask */ +#define CMXFCR_FC2 0x00400000 /* FCC2 connection */ +#define CMXFCR_RF2CS_MSK 0x00380000 /* Receive FCC2 Clock Source Mask */ +#define CMXFCR_TF2CS_MSK 0x00070000 /* Transmit FCC2 Clock Source Mask */ +#define CMXFCR_FC3 0x00004000 /* FCC3 connection */ +#define CMXFCR_RF3CS_MSK 0x00003800 /* Receive FCC3 Clock Source Mask */ +#define CMXFCR_TF3CS_MSK 0x00000700 /* Transmit FCC3 Clock Source Mask */ + +#define CMXFCR_RF1CS_BRG5 0x00000000 /* Receive FCC1 Clock Source is BRG5 */ +#define CMXFCR_RF1CS_BRG6 0x08000000 /* Receive FCC1 Clock Source is BRG6 */ +#define CMXFCR_RF1CS_BRG7 0x10000000 /* Receive FCC1 Clock Source is BRG7 */ +#define CMXFCR_RF1CS_BRG8 0x18000000 /* Receive FCC1 Clock Source is BRG8 */ +#define CMXFCR_RF1CS_CLK9 0x20000000 /* Receive FCC1 Clock Source is CLK9 */ +#define CMXFCR_RF1CS_CLK10 0x28000000 /* Receive FCC1 Clock Source is CLK10 */ +#define CMXFCR_RF1CS_CLK11 0x30000000 /* Receive FCC1 Clock Source is CLK11 */ +#define CMXFCR_RF1CS_CLK12 0x38000000 /* Receive FCC1 Clock Source is CLK12 */ + +#define CMXFCR_TF1CS_BRG5 0x00000000 /* Transmit FCC1 Clock Source is BRG5 */ +#define CMXFCR_TF1CS_BRG6 0x01000000 /* Transmit FCC1 Clock Source is BRG6 */ +#define CMXFCR_TF1CS_BRG7 0x02000000 /* Transmit FCC1 Clock Source is BRG7 */ +#define CMXFCR_TF1CS_BRG8 0x03000000 /* Transmit FCC1 Clock Source is BRG8 */ +#define CMXFCR_TF1CS_CLK9 0x04000000 /* Transmit FCC1 Clock Source is CLK9 */ +#define CMXFCR_TF1CS_CLK10 0x05000000 /* Transmit FCC1 Clock Source is CLK10 */ +#define CMXFCR_TF1CS_CLK11 0x06000000 /* Transmit FCC1 Clock Source is CLK11 */ +#define CMXFCR_TF1CS_CLK12 0x07000000 /* Transmit FCC1 Clock Source is CLK12 */ + +#define CMXFCR_RF2CS_BRG5 0x00000000 /* Receive FCC2 Clock Source is BRG5 */ +#define CMXFCR_RF2CS_BRG6 0x00080000 /* Receive FCC2 Clock Source is BRG6 */ +#define CMXFCR_RF2CS_BRG7 0x00100000 /* Receive FCC2 Clock Source is BRG7 */ +#define CMXFCR_RF2CS_BRG8 0x00180000 /* Receive FCC2 Clock Source is BRG8 */ +#define CMXFCR_RF2CS_CLK13 0x00200000 /* Receive FCC2 Clock Source is CLK13 */ +#define CMXFCR_RF2CS_CLK14 0x00280000 /* Receive FCC2 Clock Source is CLK14 */ +#define CMXFCR_RF2CS_CLK15 0x00300000 /* Receive FCC2 Clock Source is CLK15 */ +#define CMXFCR_RF2CS_CLK16 0x00380000 /* Receive FCC2 Clock Source is CLK16 */ + +#define CMXFCR_TF2CS_BRG5 0x00000000 /* Transmit FCC2 Clock Source is BRG5 */ +#define CMXFCR_TF2CS_BRG6 0x00010000 /* Transmit FCC2 Clock Source is BRG6 */ +#define CMXFCR_TF2CS_BRG7 0x00020000 /* Transmit FCC2 Clock Source is BRG7 */ +#define CMXFCR_TF2CS_BRG8 0x00030000 /* Transmit FCC2 Clock Source is BRG8 */ +#define CMXFCR_TF2CS_CLK13 0x00040000 /* Transmit FCC2 Clock Source is CLK13 */ +#define CMXFCR_TF2CS_CLK14 0x00050000 /* Transmit FCC2 Clock Source is CLK14 */ +#define CMXFCR_TF2CS_CLK15 0x00060000 /* Transmit FCC2 Clock Source is CLK15 */ +#define CMXFCR_TF2CS_CLK16 0x00070000 /* Transmit FCC2 Clock Source is CLK16 */ + +#define CMXFCR_RF3CS_BRG5 0x00000000 /* Receive FCC3 Clock Source is BRG5 */ +#define CMXFCR_RF3CS_BRG6 0x00000800 /* Receive FCC3 Clock Source is BRG6 */ +#define CMXFCR_RF3CS_BRG7 0x00001000 /* Receive FCC3 Clock Source is BRG7 */ +#define CMXFCR_RF3CS_BRG8 0x00001800 /* Receive FCC3 Clock Source is BRG8 */ +#define CMXFCR_RF3CS_CLK13 0x00002000 /* Receive FCC3 Clock Source is CLK13 */ +#define CMXFCR_RF3CS_CLK14 0x00002800 /* Receive FCC3 Clock Source is CLK14 */ +#define CMXFCR_RF3CS_CLK15 0x00003000 /* Receive FCC3 Clock Source is CLK15 */ +#define CMXFCR_RF3CS_CLK16 0x00003800 /* Receive FCC3 Clock Source is CLK16 */ + +#define CMXFCR_TF3CS_BRG5 0x00000000 /* Transmit FCC3 Clock Source is BRG5 */ +#define CMXFCR_TF3CS_BRG6 0x00000100 /* Transmit FCC3 Clock Source is BRG6 */ +#define CMXFCR_TF3CS_BRG7 0x00000200 /* Transmit FCC3 Clock Source is BRG7 */ +#define CMXFCR_TF3CS_BRG8 0x00000300 /* Transmit FCC3 Clock Source is BRG8 */ +#define CMXFCR_TF3CS_CLK13 0x00000400 /* Transmit FCC3 Clock Source is CLK13 */ +#define CMXFCR_TF3CS_CLK14 0x00000500 /* Transmit FCC3 Clock Source is CLK14 */ +#define CMXFCR_TF3CS_CLK15 0x00000600 /* Transmit FCC3 Clock Source is CLK15 */ +#define CMXFCR_TF3CS_CLK16 0x00000700 /* Transmit FCC3 Clock Source is CLK16 */ + +/*----------------------------------------------------------------------- + * CMXSCR - CMX SCC Clock Route Register + */ +#define CMXSCR_GR1 0x80000000 /* Grant Support of SCC1 */ +#define CMXSCR_SC1 0x40000000 /* SCC1 connection */ +#define CMXSCR_RS1CS_MSK 0x38000000 /* Receive SCC1 Clock Source Mask */ +#define CMXSCR_TS1CS_MSK 0x07000000 /* Transmit SCC1 Clock Source Mask */ +#define CMXSCR_GR2 0x00800000 /* Grant Support of SCC2 */ +#define CMXSCR_SC2 0x00400000 /* SCC2 connection */ +#define CMXSCR_RS2CS_MSK 0x00380000 /* Receive SCC2 Clock Source Mask */ +#define CMXSCR_TS2CS_MSK 0x00070000 /* Transmit SCC2 Clock Source Mask */ +#define CMXSCR_GR3 0x00008000 /* Grant Support of SCC3 */ +#define CMXSCR_SC3 0x00004000 /* SCC3 connection */ +#define CMXSCR_RS3CS_MSK 0x00003800 /* Receive SCC3 Clock Source Mask */ +#define CMXSCR_TS3CS_MSK 0x00000700 /* Transmit SCC3 Clock Source Mask */ +#define CMXSCR_GR4 0x00000080 /* Grant Support of SCC4 */ +#define CMXSCR_SC4 0x00000040 /* SCC4 connection */ +#define CMXSCR_RS4CS_MSK 0x00000038 /* Receive SCC4 Clock Source Mask */ +#define CMXSCR_TS4CS_MSK 0x00000007 /* Transmit SCC4 Clock Source Mask */ + +#define CMXSCR_RS1CS_BRG1 0x00000000 /* SCC1 Rx Clock Source is BRG1 */ +#define CMXSCR_RS1CS_BRG2 0x08000000 /* SCC1 Rx Clock Source is BRG2 */ +#define CMXSCR_RS1CS_BRG3 0x10000000 /* SCC1 Rx Clock Source is BRG3 */ +#define CMXSCR_RS1CS_BRG4 0x18000000 /* SCC1 Rx Clock Source is BRG4 */ +#define CMXSCR_RS1CS_CLK11 0x20000000 /* SCC1 Rx Clock Source is CLK11 */ +#define CMXSCR_RS1CS_CLK12 0x28000000 /* SCC1 Rx Clock Source is CLK12 */ +#define CMXSCR_RS1CS_CLK3 0x30000000 /* SCC1 Rx Clock Source is CLK3 */ +#define CMXSCR_RS1CS_CLK4 0x38000000 /* SCC1 Rx Clock Source is CLK4 */ + +#define CMXSCR_TS1CS_BRG1 0x00000000 /* SCC1 Tx Clock Source is BRG1 */ +#define CMXSCR_TS1CS_BRG2 0x01000000 /* SCC1 Tx Clock Source is BRG2 */ +#define CMXSCR_TS1CS_BRG3 0x02000000 /* SCC1 Tx Clock Source is BRG3 */ +#define CMXSCR_TS1CS_BRG4 0x03000000 /* SCC1 Tx Clock Source is BRG4 */ +#define CMXSCR_TS1CS_CLK11 0x04000000 /* SCC1 Tx Clock Source is CLK11 */ +#define CMXSCR_TS1CS_CLK12 0x05000000 /* SCC1 Tx Clock Source is CLK12 */ +#define CMXSCR_TS1CS_CLK3 0x06000000 /* SCC1 Tx Clock Source is CLK3 */ +#define CMXSCR_TS1CS_CLK4 0x07000000 /* SCC1 Tx Clock Source is CLK4 */ + +#define CMXSCR_RS2CS_BRG1 0x00000000 /* SCC2 Rx Clock Source is BRG1 */ +#define CMXSCR_RS2CS_BRG2 0x00080000 /* SCC2 Rx Clock Source is BRG2 */ +#define CMXSCR_RS2CS_BRG3 0x00100000 /* SCC2 Rx Clock Source is BRG3 */ +#define CMXSCR_RS2CS_BRG4 0x00180000 /* SCC2 Rx Clock Source is BRG4 */ +#define CMXSCR_RS2CS_CLK11 0x00200000 /* SCC2 Rx Clock Source is CLK11 */ +#define CMXSCR_RS2CS_CLK12 0x00280000 /* SCC2 Rx Clock Source is CLK12 */ +#define CMXSCR_RS2CS_CLK3 0x00300000 /* SCC2 Rx Clock Source is CLK3 */ +#define CMXSCR_RS2CS_CLK4 0x00380000 /* SCC2 Rx Clock Source is CLK4 */ + +#define CMXSCR_TS2CS_BRG1 0x00000000 /* SCC2 Tx Clock Source is BRG1 */ +#define CMXSCR_TS2CS_BRG2 0x00010000 /* SCC2 Tx Clock Source is BRG2 */ +#define CMXSCR_TS2CS_BRG3 0x00020000 /* SCC2 Tx Clock Source is BRG3 */ +#define CMXSCR_TS2CS_BRG4 0x00030000 /* SCC2 Tx Clock Source is BRG4 */ +#define CMXSCR_TS2CS_CLK11 0x00040000 /* SCC2 Tx Clock Source is CLK11 */ +#define CMXSCR_TS2CS_CLK12 0x00050000 /* SCC2 Tx Clock Source is CLK12 */ +#define CMXSCR_TS2CS_CLK3 0x00060000 /* SCC2 Tx Clock Source is CLK3 */ +#define CMXSCR_TS2CS_CLK4 0x00070000 /* SCC2 Tx Clock Source is CLK4 */ + +#define CMXSCR_RS3CS_BRG1 0x00000000 /* SCC3 Rx Clock Source is BRG1 */ +#define CMXSCR_RS3CS_BRG2 0x00000800 /* SCC3 Rx Clock Source is BRG2 */ +#define CMXSCR_RS3CS_BRG3 0x00001000 /* SCC3 Rx Clock Source is BRG3 */ +#define CMXSCR_RS3CS_BRG4 0x00001800 /* SCC3 Rx Clock Source is BRG4 */ +#define CMXSCR_RS3CS_CLK5 0x00002000 /* SCC3 Rx Clock Source is CLK5 */ +#define CMXSCR_RS3CS_CLK6 0x00002800 /* SCC3 Rx Clock Source is CLK6 */ +#define CMXSCR_RS3CS_CLK7 0x00003000 /* SCC3 Rx Clock Source is CLK7 */ +#define CMXSCR_RS3CS_CLK8 0x00003800 /* SCC3 Rx Clock Source is CLK8 */ + +#define CMXSCR_TS3CS_BRG1 0x00000000 /* SCC3 Tx Clock Source is BRG1 */ +#define CMXSCR_TS3CS_BRG2 0x00000100 /* SCC3 Tx Clock Source is BRG2 */ +#define CMXSCR_TS3CS_BRG3 0x00000200 /* SCC3 Tx Clock Source is BRG3 */ +#define CMXSCR_TS3CS_BRG4 0x00000300 /* SCC3 Tx Clock Source is BRG4 */ +#define CMXSCR_TS3CS_CLK5 0x00000400 /* SCC3 Tx Clock Source is CLK5 */ +#define CMXSCR_TS3CS_CLK6 0x00000500 /* SCC3 Tx Clock Source is CLK6 */ +#define CMXSCR_TS3CS_CLK7 0x00000600 /* SCC3 Tx Clock Source is CLK7 */ +#define CMXSCR_TS3CS_CLK8 0x00000700 /* SCC3 Tx Clock Source is CLK8 */ + +#define CMXSCR_RS4CS_BRG1 0x00000000 /* SCC4 Rx Clock Source is BRG1 */ +#define CMXSCR_RS4CS_BRG2 0x00000008 /* SCC4 Rx Clock Source is BRG2 */ +#define CMXSCR_RS4CS_BRG3 0x00000010 /* SCC4 Rx Clock Source is BRG3 */ +#define CMXSCR_RS4CS_BRG4 0x00000018 /* SCC4 Rx Clock Source is BRG4 */ +#define CMXSCR_RS4CS_CLK5 0x00000020 /* SCC4 Rx Clock Source is CLK5 */ +#define CMXSCR_RS4CS_CLK6 0x00000028 /* SCC4 Rx Clock Source is CLK6 */ +#define CMXSCR_RS4CS_CLK7 0x00000030 /* SCC4 Rx Clock Source is CLK7 */ +#define CMXSCR_RS4CS_CLK8 0x00000038 /* SCC4 Rx Clock Source is CLK8 */ + +#define CMXSCR_TS4CS_BRG1 0x00000000 /* SCC4 Tx Clock Source is BRG1 */ +#define CMXSCR_TS4CS_BRG2 0x00000001 /* SCC4 Tx Clock Source is BRG2 */ +#define CMXSCR_TS4CS_BRG3 0x00000002 /* SCC4 Tx Clock Source is BRG3 */ +#define CMXSCR_TS4CS_BRG4 0x00000003 /* SCC4 Tx Clock Source is BRG4 */ +#define CMXSCR_TS4CS_CLK5 0x00000004 /* SCC4 Tx Clock Source is CLK5 */ +#define CMXSCR_TS4CS_CLK6 0x00000005 /* SCC4 Tx Clock Source is CLK6 */ +#define CMXSCR_TS4CS_CLK7 0x00000006 /* SCC4 Tx Clock Source is CLK7 */ +#define CMXSCR_TS4CS_CLK8 0x00000007 /* SCC4 Tx Clock Source is CLK8 */ + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration Register 4-31 + */ +#define SIUMCR_BBD 0x80000000 /* Bus Busy Disable */ +#define SIUMCR_ESE 0x40000000 /* External Snoop Enable */ +#define SIUMCR_PBSE 0x20000000 /* Parity Byte Select Enable */ +#define SIUMCR_CDIS 0x10000000 /* Core Disable */ +#define SIUMCR_DPPC00 0x00000000 /* Data Parity Pins Configuration*/ +#define SIUMCR_DPPC01 0x04000000 /* - " - */ +#define SIUMCR_DPPC10 0x08000000 /* - " - */ +#define SIUMCR_DPPC11 0x0c000000 /* - " - */ +#define SIUMCR_L2CPC00 0x00000000 /* L2 Cache Pins Configuration */ +#define SIUMCR_L2CPC01 0x01000000 /* - " - */ +#define SIUMCR_L2CPC10 0x02000000 /* - " - */ +#define SIUMCR_L2CPC11 0x03000000 /* - " - */ +#define SIUMCR_LBPC00 0x00000000 /* Local Bus Pins Configuration */ +#define SIUMCR_LBPC01 0x00400000 /* - " - */ +#define SIUMCR_LBPC10 0x00800000 /* - " - */ +#define SIUMCR_LBPC11 0x00c00000 /* - " - */ +#define SIUMCR_APPC00 0x00000000 /* Address Parity Pins Configuration*/ +#define SIUMCR_APPC01 0x00100000 /* - " - */ +#define SIUMCR_APPC10 0x00200000 /* - " - */ +#define SIUMCR_APPC11 0x00300000 /* - " - */ +#define SIUMCR_CS10PC00 0x00000000 /* CS10 Pin Configuration */ +#define SIUMCR_CS10PC01 0x00040000 /* - " - */ +#define SIUMCR_CS10PC10 0x00080000 /* - " - */ +#define SIUMCR_CS10PC11 0x000c0000 /* - " - */ +#define SIUMCR_BCTLC00 0x00000000 /* Buffer Control Configuration */ +#define SIUMCR_BCTLC01 0x00010000 /* - " - */ +#define SIUMCR_BCTLC10 0x00020000 /* - " - */ +#define SIUMCR_BCTLC11 0x00030000 /* - " - */ +#define SIUMCR_MMR00 0x00000000 /* Mask Masters Requests */ +#define SIUMCR_MMR01 0x00004000 /* - " - */ +#define SIUMCR_MMR10 0x00008000 /* - " - */ +#define SIUMCR_MMR11 0x0000c000 /* - " - */ +#define SIUMCR_LPBSE 0x00002000 /* LocalBus Parity Byte Select Enable*/ + +/*----------------------------------------------------------------------- + * SCCR - System Clock Control Register 9-8 +*/ +#define SCCR_PCI_MODE 0x00000100 /* PCI Mode */ +#define SCCR_PCI_MODCK 0x00000080 /* Value of PCI_MODCK pin */ +#define SCCR_PCIDF_MSK 0x00000078 /* PCI division factor */ +#define SCCR_PCIDF_SHIFT 3 + +#ifndef CPM_IMMR_OFFSET +#define CPM_IMMR_OFFSET 0x101a8 +#endif + +#define FCC_PSMR_RMII ((uint)0x00020000) /* Use RMII interface */ + +/* FCC iop & clock configuration. BSP code is responsible to define Fx_RXCLK & Fx_TXCLK + * in order to use clock-computing stuff below for the FCC x + */ + +/* Automatically generates register configurations */ +#define PC_CLK(x) ((uint)(1<<(x-1))) /* FCC CLK I/O ports */ + +#define CMXFCR_RF1CS(x) ((uint)((x-5)<<27)) /* FCC1 Receive Clock Source */ +#define CMXFCR_TF1CS(x) ((uint)((x-5)<<24)) /* FCC1 Transmit Clock Source */ +#define CMXFCR_RF2CS(x) ((uint)((x-9)<<19)) /* FCC2 Receive Clock Source */ +#define CMXFCR_TF2CS(x) ((uint)((x-9)<<16)) /* FCC2 Transmit Clock Source */ +#define CMXFCR_RF3CS(x) ((uint)((x-9)<<11)) /* FCC3 Receive Clock Source */ +#define CMXFCR_TF3CS(x) ((uint)((x-9)<<8)) /* FCC3 Transmit Clock Source */ + +#define PC_F1RXCLK PC_CLK(F1_RXCLK) +#define PC_F1TXCLK PC_CLK(F1_TXCLK) +#define CMX1_CLK_ROUTE (CMXFCR_RF1CS(F1_RXCLK) | CMXFCR_TF1CS(F1_TXCLK)) +#define CMX1_CLK_MASK ((uint)0xff000000) + +#define PC_F2RXCLK PC_CLK(F2_RXCLK) +#define PC_F2TXCLK PC_CLK(F2_TXCLK) +#define CMX2_CLK_ROUTE (CMXFCR_RF2CS(F2_RXCLK) | CMXFCR_TF2CS(F2_TXCLK)) +#define CMX2_CLK_MASK ((uint)0x00ff0000) + +#define PC_F3RXCLK PC_CLK(F3_RXCLK) +#define PC_F3TXCLK PC_CLK(F3_TXCLK) +#define CMX3_CLK_ROUTE (CMXFCR_RF3CS(F3_RXCLK) | CMXFCR_TF3CS(F3_TXCLK)) +#define CMX3_CLK_MASK ((uint)0x0000ff00) + +#define CPMUX_CLK_MASK (CMX3_CLK_MASK | CMX2_CLK_MASK) +#define CPMUX_CLK_ROUTE (CMX3_CLK_ROUTE | CMX2_CLK_ROUTE) + +#define CLK_TRX (PC_F3TXCLK | PC_F3RXCLK | PC_F2TXCLK | PC_F2RXCLK) + +/* I/O Pin assignment for FCC1. I don't yet know the best way to do this, + * but there is little variation among the choices. + */ +#define PA1_COL 0x00000001U +#define PA1_CRS 0x00000002U +#define PA1_TXER 0x00000004U +#define PA1_TXEN 0x00000008U +#define PA1_RXDV 0x00000010U +#define PA1_RXER 0x00000020U +#define PA1_TXDAT 0x00003c00U +#define PA1_RXDAT 0x0003c000U +#define PA1_PSORA0 (PA1_RXDAT | PA1_TXDAT) +#define PA1_PSORA1 (PA1_COL | PA1_CRS | PA1_TXER | PA1_TXEN | \ + PA1_RXDV | PA1_RXER) +#define PA1_DIRA0 (PA1_RXDAT | PA1_CRS | PA1_COL | PA1_RXER | PA1_RXDV) +#define PA1_DIRA1 (PA1_TXDAT | PA1_TXEN | PA1_TXER) + + +/* I/O Pin assignment for FCC2. I don't yet know the best way to do this, + * but there is little variation among the choices. + */ +#define PB2_TXER 0x00000001U +#define PB2_RXDV 0x00000002U +#define PB2_TXEN 0x00000004U +#define PB2_RXER 0x00000008U +#define PB2_COL 0x00000010U +#define PB2_CRS 0x00000020U +#define PB2_TXDAT 0x000003c0U +#define PB2_RXDAT 0x00003c00U +#define PB2_PSORB0 (PB2_RXDAT | PB2_TXDAT | PB2_CRS | PB2_COL | \ + PB2_RXER | PB2_RXDV | PB2_TXER) +#define PB2_PSORB1 (PB2_TXEN) +#define PB2_DIRB0 (PB2_RXDAT | PB2_CRS | PB2_COL | PB2_RXER | PB2_RXDV) +#define PB2_DIRB1 (PB2_TXDAT | PB2_TXEN | PB2_TXER) + + +/* I/O Pin assignment for FCC3. I don't yet know the best way to do this, + * but there is little variation among the choices. + */ +#define PB3_RXDV 0x00004000U +#define PB3_RXER 0x00008000U +#define PB3_TXER 0x00010000U +#define PB3_TXEN 0x00020000U +#define PB3_COL 0x00040000U +#define PB3_CRS 0x00080000U +#define PB3_TXDAT 0x0f000000U +#define PC3_TXDAT 0x00000010U +#define PB3_RXDAT 0x00f00000U +#define PB3_PSORB0 (PB3_RXDAT | PB3_TXDAT | PB3_CRS | PB3_COL | \ + PB3_RXER | PB3_RXDV | PB3_TXER | PB3_TXEN) +#define PB3_PSORB1 0 +#define PB3_DIRB0 (PB3_RXDAT | PB3_CRS | PB3_COL | PB3_RXER | PB3_RXDV) +#define PB3_DIRB1 (PB3_TXDAT | PB3_TXEN | PB3_TXER) +#define PC3_DIRC1 (PC3_TXDAT) + +/* Handy macro to specify mem for FCCs*/ +#define FCC_MEM_OFFSET(x) (CPM_FCC_SPECIAL_BASE + (x*128)) +#define FCC1_MEM_OFFSET FCC_MEM_OFFSET(0) +#define FCC2_MEM_OFFSET FCC_MEM_OFFSET(1) +#define FCC3_MEM_OFFSET FCC_MEM_OFFSET(2) + +/* Clocks and GRG's */ + +enum cpm_clk_dir { + CPM_CLK_RX, + CPM_CLK_TX, + CPM_CLK_RTX +}; + +enum cpm_clk_target { + CPM_CLK_SCC1, + CPM_CLK_SCC2, + CPM_CLK_SCC3, + CPM_CLK_SCC4, + CPM_CLK_FCC1, + CPM_CLK_FCC2, + CPM_CLK_FCC3 +}; + +enum cpm_clk { + CPM_CLK_NONE = 0, + CPM_BRG1, /* Baud Rate Generator 1 */ + CPM_BRG2, /* Baud Rate Generator 2 */ + CPM_BRG3, /* Baud Rate Generator 3 */ + CPM_BRG4, /* Baud Rate Generator 4 */ + CPM_BRG5, /* Baud Rate Generator 5 */ + CPM_BRG6, /* Baud Rate Generator 6 */ + CPM_BRG7, /* Baud Rate Generator 7 */ + CPM_BRG8, /* Baud Rate Generator 8 */ + CPM_CLK1, /* Clock 1 */ + CPM_CLK2, /* Clock 2 */ + CPM_CLK3, /* Clock 3 */ + CPM_CLK4, /* Clock 4 */ + CPM_CLK5, /* Clock 5 */ + CPM_CLK6, /* Clock 6 */ + CPM_CLK7, /* Clock 7 */ + CPM_CLK8, /* Clock 8 */ + CPM_CLK9, /* Clock 9 */ + CPM_CLK10, /* Clock 10 */ + CPM_CLK11, /* Clock 11 */ + CPM_CLK12, /* Clock 12 */ + CPM_CLK13, /* Clock 13 */ + CPM_CLK14, /* Clock 14 */ + CPM_CLK15, /* Clock 15 */ + CPM_CLK16, /* Clock 16 */ + CPM_CLK17, /* Clock 17 */ + CPM_CLK18, /* Clock 18 */ + CPM_CLK19, /* Clock 19 */ + CPM_CLK20, /* Clock 20 */ + CPM_CLK_DUMMY +}; + +extern int cpm2_clk_setup(enum cpm_clk_target target, int clock, int mode); + +#endif /* __CPM2__ */ +#endif /* __KERNEL__ */ diff --git a/include/asm-powerpc/highmem.h b/include/asm-powerpc/highmem.h new file mode 100644 index 00000000000..f7b21ee302b --- /dev/null +++ b/include/asm-powerpc/highmem.h @@ -0,0 +1,135 @@ +/* + * highmem.h: virtual kernel memory mappings for high memory + * + * PowerPC version, stolen from the i386 version. + * + * Used in CONFIG_HIGHMEM systems for memory pages which + * are not addressable by direct kernel virtual addresses. + * + * Copyright (C) 1999 Gerhard Wichert, Siemens AG + * Gerhard.Wichert@pdb.siemens.de + * + * + * Redesigned the x86 32-bit VM architecture to deal with + * up to 16 Terrabyte physical memory. With current x86 CPUs + * we now support up to 64 Gigabytes physical RAM. + * + * Copyright (C) 1999 Ingo Molnar + */ + +#ifndef _ASM_HIGHMEM_H +#define _ASM_HIGHMEM_H + +#ifdef __KERNEL__ + +#include +#include +#include +#include +#include + +/* undef for production */ +#define HIGHMEM_DEBUG 1 + +extern pte_t *kmap_pte; +extern pgprot_t kmap_prot; +extern pte_t *pkmap_page_table; + +/* + * Right now we initialize only a single pte table. It can be extended + * easily, subsequent pte tables have to be allocated in one physical + * chunk of RAM. + */ +#define PKMAP_BASE CONFIG_HIGHMEM_START +#define LAST_PKMAP (1 << PTE_SHIFT) +#define LAST_PKMAP_MASK (LAST_PKMAP-1) +#define PKMAP_NR(virt) ((virt-PKMAP_BASE) >> PAGE_SHIFT) +#define PKMAP_ADDR(nr) (PKMAP_BASE + ((nr) << PAGE_SHIFT)) + +#define KMAP_FIX_BEGIN (PKMAP_BASE + 0x00400000UL) + +extern void *kmap_high(struct page *page); +extern void kunmap_high(struct page *page); + +static inline void *kmap(struct page *page) +{ + might_sleep(); + if (!PageHighMem(page)) + return page_address(page); + return kmap_high(page); +} + +static inline void kunmap(struct page *page) +{ + BUG_ON(in_interrupt()); + if (!PageHighMem(page)) + return; + kunmap_high(page); +} + +/* + * The use of kmap_atomic/kunmap_atomic is discouraged - kmap/kunmap + * gives a more generic (and caching) interface. But kmap_atomic can + * be used in IRQ contexts, so in some (very limited) cases we need + * it. + */ +static inline void *kmap_atomic(struct page *page, enum km_type type) +{ + unsigned int idx; + unsigned long vaddr; + + /* even !CONFIG_PREEMPT needs this, for in_atomic in do_page_fault */ + pagefault_disable(); + if (!PageHighMem(page)) + return page_address(page); + + idx = type + KM_TYPE_NR*smp_processor_id(); + vaddr = KMAP_FIX_BEGIN + idx * PAGE_SIZE; +#ifdef HIGHMEM_DEBUG + BUG_ON(!pte_none(*(kmap_pte+idx))); +#endif + set_pte_at(&init_mm, vaddr, kmap_pte+idx, mk_pte(page, kmap_prot)); + flush_tlb_page(NULL, vaddr); + + return (void*) vaddr; +} + +static inline void kunmap_atomic(void *kvaddr, enum km_type type) +{ +#ifdef HIGHMEM_DEBUG + unsigned long vaddr = (unsigned long) kvaddr & PAGE_MASK; + unsigned int idx = type + KM_TYPE_NR*smp_processor_id(); + + if (vaddr < KMAP_FIX_BEGIN) { // FIXME + pagefault_enable(); + return; + } + + BUG_ON(vaddr != KMAP_FIX_BEGIN + idx * PAGE_SIZE); + + /* + * force other mappings to Oops if they'll try to access + * this pte without first remap it + */ + pte_clear(&init_mm, vaddr, kmap_pte+idx); + flush_tlb_page(NULL, vaddr); +#endif + pagefault_enable(); +} + +static inline struct page *kmap_atomic_to_page(void *ptr) +{ + unsigned long idx, vaddr = (unsigned long) ptr; + + if (vaddr < KMAP_FIX_BEGIN) + return virt_to_page(ptr); + + idx = (vaddr - KMAP_FIX_BEGIN) >> PAGE_SHIFT; + return pte_page(kmap_pte[idx]); +} + +#define flush_cache_kmaps() flush_cache_all() + +#endif /* __KERNEL__ */ + +#endif /* _ASM_HIGHMEM_H */ diff --git a/include/asm-powerpc/hydra.h b/include/asm-powerpc/hydra.h new file mode 100644 index 00000000000..1ad4eed07fb --- /dev/null +++ b/include/asm-powerpc/hydra.h @@ -0,0 +1,102 @@ +/* + * include/asm-ppc/hydra.h -- Mac I/O `Hydra' definitions + * + * Copyright (C) 1997 Geert Uytterhoeven + * + * This file is based on the following documentation: + * + * Macintosh Technology in the Common Hardware Reference Platform + * Apple Computer, Inc. + * + * © Copyright 1995 Apple Computer, Inc. All rights reserved. + * + * It's available online from http://chrp.apple.com/MacTech.pdf. + * You can obtain paper copies of this book from computer bookstores or by + * writing Morgan Kaufmann Publishers, Inc., 340 Pine Street, Sixth Floor, San + * Francisco, CA 94104. Reference ISBN 1-55860-393-X. + * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file COPYING in the main directory of this archive + * for more details. + */ + +#ifndef _ASMPPC_HYDRA_H +#define _ASMPPC_HYDRA_H + +#ifdef __KERNEL__ + +struct Hydra { + /* DBDMA Controller Register Space */ + char Pad1[0x30]; + u_int CachePD; + u_int IDs; + u_int Feature_Control; + char Pad2[0x7fc4]; + /* DBDMA Channel Register Space */ + char SCSI_DMA[0x100]; + char Pad3[0x300]; + char SCCA_Tx_DMA[0x100]; + char SCCA_Rx_DMA[0x100]; + char SCCB_Tx_DMA[0x100]; + char SCCB_Rx_DMA[0x100]; + char Pad4[0x7800]; + /* Device Register Space */ + char SCSI[0x1000]; + char ADB[0x1000]; + char SCC_Legacy[0x1000]; + char SCC[0x1000]; + char Pad9[0x2000]; + char VIA[0x2000]; + char Pad10[0x28000]; + char OpenPIC[0x40000]; +}; + +extern volatile struct Hydra __iomem *Hydra; + + + /* + * Feature Control Register + */ + +#define HYDRA_FC_SCC_CELL_EN 0x00000001 /* Enable SCC Clock */ +#define HYDRA_FC_SCSI_CELL_EN 0x00000002 /* Enable SCSI Clock */ +#define HYDRA_FC_SCCA_ENABLE 0x00000004 /* Enable SCC A Lines */ +#define HYDRA_FC_SCCB_ENABLE 0x00000008 /* Enable SCC B Lines */ +#define HYDRA_FC_ARB_BYPASS 0x00000010 /* Bypass Internal Arbiter */ +#define HYDRA_FC_RESET_SCC 0x00000020 /* Reset SCC */ +#define HYDRA_FC_MPIC_ENABLE 0x00000040 /* Enable OpenPIC */ +#define HYDRA_FC_SLOW_SCC_PCLK 0x00000080 /* 1=15.6672, 0=25 MHz */ +#define HYDRA_FC_MPIC_IS_MASTER 0x00000100 /* OpenPIC Master Mode */ + + + /* + * OpenPIC Interrupt Sources + */ + +#define HYDRA_INT_SIO 0 +#define HYDRA_INT_SCSI_DMA 1 +#define HYDRA_INT_SCCA_TX_DMA 2 +#define HYDRA_INT_SCCA_RX_DMA 3 +#define HYDRA_INT_SCCB_TX_DMA 4 +#define HYDRA_INT_SCCB_RX_DMA 5 +#define HYDRA_INT_SCSI 6 +#define HYDRA_INT_SCCA 7 +#define HYDRA_INT_SCCB 8 +#define HYDRA_INT_VIA 9 +#define HYDRA_INT_ADB 10 +#define HYDRA_INT_ADB_NMI 11 +#define HYDRA_INT_EXT1 12 /* PCI IRQW */ +#define HYDRA_INT_EXT2 13 /* PCI IRQX */ +#define HYDRA_INT_EXT3 14 /* PCI IRQY */ +#define HYDRA_INT_EXT4 15 /* PCI IRQZ */ +#define HYDRA_INT_EXT5 16 /* IDE Primay/Secondary */ +#define HYDRA_INT_EXT6 17 /* IDE Secondary */ +#define HYDRA_INT_EXT7 18 /* Power Off Request */ +#define HYDRA_INT_SPARE 19 + +extern int hydra_init(void); +extern void macio_adb_init(void); + +#endif /* __KERNEL__ */ + +#endif /* _ASMPPC_HYDRA_H */ diff --git a/include/asm-powerpc/immap_cpm2.h b/include/asm-powerpc/immap_cpm2.h new file mode 100644 index 00000000000..f316a91c628 --- /dev/null +++ b/include/asm-powerpc/immap_cpm2.h @@ -0,0 +1,648 @@ +/* + * CPM2 Internal Memory Map + * Copyright (c) 1999 Dan Malek (dmalek@jlc.net) + * + * The Internal Memory Map for devices with CPM2 on them. This + * is the superset of all CPM2 devices (8260, 8266, 8280, 8272, + * 8560). + */ +#ifdef __KERNEL__ +#ifndef __IMMAP_CPM2__ +#define __IMMAP_CPM2__ + +/* System configuration registers. +*/ +typedef struct sys_82xx_conf { + u32 sc_siumcr; + u32 sc_sypcr; + u8 res1[6]; + u16 sc_swsr; + u8 res2[20]; + u32 sc_bcr; + u8 sc_ppc_acr; + u8 res3[3]; + u32 sc_ppc_alrh; + u32 sc_ppc_alrl; + u8 sc_lcl_acr; + u8 res4[3]; + u32 sc_lcl_alrh; + u32 sc_lcl_alrl; + u32 sc_tescr1; + u32 sc_tescr2; + u32 sc_ltescr1; + u32 sc_ltescr2; + u32 sc_pdtea; + u8 sc_pdtem; + u8 res5[3]; + u32 sc_ldtea; + u8 sc_ldtem; + u8 res6[163]; +} sysconf_82xx_cpm2_t; + +typedef struct sys_85xx_conf { + u32 sc_cear; + u16 sc_ceer; + u16 sc_cemr; + u8 res1[70]; + u32 sc_smaer; + u8 res2[4]; + u32 sc_smevr; + u32 sc_smctr; + u32 sc_lmaer; + u8 res3[4]; + u32 sc_lmevr; + u32 sc_lmctr; + u8 res4[144]; +} sysconf_85xx_cpm2_t; + +typedef union sys_conf { + sysconf_82xx_cpm2_t siu_82xx; + sysconf_85xx_cpm2_t siu_85xx; +} sysconf_cpm2_t; + + + +/* Memory controller registers. +*/ +typedef struct mem_ctlr { + u32 memc_br0; + u32 memc_or0; + u32 memc_br1; + u32 memc_or1; + u32 memc_br2; + u32 memc_or2; + u32 memc_br3; + u32 memc_or3; + u32 memc_br4; + u32 memc_or4; + u32 memc_br5; + u32 memc_or5; + u32 memc_br6; + u32 memc_or6; + u32 memc_br7; + u32 memc_or7; + u32 memc_br8; + u32 memc_or8; + u32 memc_br9; + u32 memc_or9; + u32 memc_br10; + u32 memc_or10; + u32 memc_br11; + u32 memc_or11; + u8 res1[8]; + u32 memc_mar; + u8 res2[4]; + u32 memc_mamr; + u32 memc_mbmr; + u32 memc_mcmr; + u8 res3[8]; + u16 memc_mptpr; + u8 res4[2]; + u32 memc_mdr; + u8 res5[4]; + u32 memc_psdmr; + u32 memc_lsdmr; + u8 memc_purt; + u8 res6[3]; + u8 memc_psrt; + u8 res7[3]; + u8 memc_lurt; + u8 res8[3]; + u8 memc_lsrt; + u8 res9[3]; + u32 memc_immr; + u32 memc_pcibr0; + u32 memc_pcibr1; + u8 res10[16]; + u32 memc_pcimsk0; + u32 memc_pcimsk1; + u8 res11[52]; +} memctl_cpm2_t; + +/* System Integration Timers. +*/ +typedef struct sys_int_timers { + u8 res1[32]; + u16 sit_tmcntsc; + u8 res2[2]; + u32 sit_tmcnt; + u8 res3[4]; + u32 sit_tmcntal; + u8 res4[16]; + u16 sit_piscr; + u8 res5[2]; + u32 sit_pitc; + u32 sit_pitr; + u8 res6[94]; + u8 res7[390]; +} sit_cpm2_t; + +#define PISCR_PIRQ_MASK ((u16)0xff00) +#define PISCR_PS ((u16)0x0080) +#define PISCR_PIE ((u16)0x0004) +#define PISCR_PTF ((u16)0x0002) +#define PISCR_PTE ((u16)0x0001) + +/* PCI Controller. +*/ +typedef struct pci_ctlr { + u32 pci_omisr; + u32 pci_omimr; + u8 res1[8]; + u32 pci_ifqpr; + u32 pci_ofqpr; + u8 res2[8]; + u32 pci_imr0; + u32 pci_imr1; + u32 pci_omr0; + u32 pci_omr1; + u32 pci_odr; + u8 res3[4]; + u32 pci_idr; + u8 res4[20]; + u32 pci_imisr; + u32 pci_imimr; + u8 res5[24]; + u32 pci_ifhpr; + u8 res6[4]; + u32 pci_iftpr; + u8 res7[4]; + u32 pci_iphpr; + u8 res8[4]; + u32 pci_iptpr; + u8 res9[4]; + u32 pci_ofhpr; + u8 res10[4]; + u32 pci_oftpr; + u8 res11[4]; + u32 pci_ophpr; + u8 res12[4]; + u32 pci_optpr; + u8 res13[8]; + u32 pci_mucr; + u8 res14[8]; + u32 pci_qbar; + u8 res15[12]; + u32 pci_dmamr0; + u32 pci_dmasr0; + u32 pci_dmacdar0; + u8 res16[4]; + u32 pci_dmasar0; + u8 res17[4]; + u32 pci_dmadar0; + u8 res18[4]; + u32 pci_dmabcr0; + u32 pci_dmandar0; + u8 res19[86]; + u32 pci_dmamr1; + u32 pci_dmasr1; + u32 pci_dmacdar1; + u8 res20[4]; + u32 pci_dmasar1; + u8 res21[4]; + u32 pci_dmadar1; + u8 res22[4]; + u32 pci_dmabcr1; + u32 pci_dmandar1; + u8 res23[88]; + u32 pci_dmamr2; + u32 pci_dmasr2; + u32 pci_dmacdar2; + u8 res24[4]; + u32 pci_dmasar2; + u8 res25[4]; + u32 pci_dmadar2; + u8 res26[4]; + u32 pci_dmabcr2; + u32 pci_dmandar2; + u8 res27[88]; + u32 pci_dmamr3; + u32 pci_dmasr3; + u32 pci_dmacdar3; + u8 res28[4]; + u32 pci_dmasar3; + u8 res29[4]; + u32 pci_dmadar3; + u8 res30[4]; + u32 pci_dmabcr3; + u32 pci_dmandar3; + u8 res31[344]; + u32 pci_potar0; + u8 res32[4]; + u32 pci_pobar0; + u8 res33[4]; + u32 pci_pocmr0; + u8 res34[4]; + u32 pci_potar1; + u8 res35[4]; + u32 pci_pobar1; + u8 res36[4]; + u32 pci_pocmr1; + u8 res37[4]; + u32 pci_potar2; + u8 res38[4]; + u32 pci_pobar2; + u8 res39[4]; + u32 pci_pocmr2; + u8 res40[50]; + u32 pci_ptcr; + u32 pci_gpcr; + u32 pci_gcr; + u32 pci_esr; + u32 pci_emr; + u32 pci_ecr; + u32 pci_eacr; + u8 res41[4]; + u32 pci_edcr; + u8 res42[4]; + u32 pci_eccr; + u8 res43[44]; + u32 pci_pitar1; + u8 res44[4]; + u32 pci_pibar1; + u8 res45[4]; + u32 pci_picmr1; + u8 res46[4]; + u32 pci_pitar0; + u8 res47[4]; + u32 pci_pibar0; + u8 res48[4]; + u32 pci_picmr0; + u8 res49[4]; + u32 pci_cfg_addr; + u32 pci_cfg_data; + u32 pci_int_ack; + u8 res50[756]; +} pci_cpm2_t; + +/* Interrupt Controller. +*/ +typedef struct interrupt_controller { + u16 ic_sicr; + u8 res1[2]; + u32 ic_sivec; + u32 ic_sipnrh; + u32 ic_sipnrl; + u32 ic_siprr; + u32 ic_scprrh; + u32 ic_scprrl; + u32 ic_simrh; + u32 ic_simrl; + u32 ic_siexr; + u8 res2[88]; +} intctl_cpm2_t; + +/* Clocks and Reset. +*/ +typedef struct clk_and_reset { + u32 car_sccr; + u8 res1[4]; + u32 car_scmr; + u8 res2[4]; + u32 car_rsr; + u32 car_rmr; + u8 res[104]; +} car_cpm2_t; + +/* Input/Output Port control/status registers. + * Names consistent with processor manual, although they are different + * from the original 8xx names....... + */ +typedef struct io_port { + u32 iop_pdira; + u32 iop_ppara; + u32 iop_psora; + u32 iop_podra; + u32 iop_pdata; + u8 res1[12]; + u32 iop_pdirb; + u32 iop_pparb; + u32 iop_psorb; + u32 iop_podrb; + u32 iop_pdatb; + u8 res2[12]; + u32 iop_pdirc; + u32 iop_pparc; + u32 iop_psorc; + u32 iop_podrc; + u32 iop_pdatc; + u8 res3[12]; + u32 iop_pdird; + u32 iop_ppard; + u32 iop_psord; + u32 iop_podrd; + u32 iop_pdatd; + u8 res4[12]; +} iop_cpm2_t; + +/* Communication Processor Module Timers +*/ +typedef struct cpm_timers { + u8 cpmt_tgcr1; + u8 res1[3]; + u8 cpmt_tgcr2; + u8 res2[11]; + u16 cpmt_tmr1; + u16 cpmt_tmr2; + u16 cpmt_trr1; + u16 cpmt_trr2; + u16 cpmt_tcr1; + u16 cpmt_tcr2; + u16 cpmt_tcn1; + u16 cpmt_tcn2; + u16 cpmt_tmr3; + u16 cpmt_tmr4; + u16 cpmt_trr3; + u16 cpmt_trr4; + u16 cpmt_tcr3; + u16 cpmt_tcr4; + u16 cpmt_tcn3; + u16 cpmt_tcn4; + u16 cpmt_ter1; + u16 cpmt_ter2; + u16 cpmt_ter3; + u16 cpmt_ter4; + u8 res3[584]; +} cpmtimer_cpm2_t; + +/* DMA control/status registers. +*/ +typedef struct sdma_csr { + u8 res0[24]; + u8 sdma_sdsr; + u8 res1[3]; + u8 sdma_sdmr; + u8 res2[3]; + u8 sdma_idsr1; + u8 res3[3]; + u8 sdma_idmr1; + u8 res4[3]; + u8 sdma_idsr2; + u8 res5[3]; + u8 sdma_idmr2; + u8 res6[3]; + u8 sdma_idsr3; + u8 res7[3]; + u8 sdma_idmr3; + u8 res8[3]; + u8 sdma_idsr4; + u8 res9[3]; + u8 sdma_idmr4; + u8 res10[707]; +} sdma_cpm2_t; + +/* Fast controllers +*/ +typedef struct fcc { + u32 fcc_gfmr; + u32 fcc_fpsmr; + u16 fcc_ftodr; + u8 res1[2]; + u16 fcc_fdsr; + u8 res2[2]; + u16 fcc_fcce; + u8 res3[2]; + u16 fcc_fccm; + u8 res4[2]; + u8 fcc_fccs; + u8 res5[3]; + u8 fcc_ftirr_phy[4]; +} fcc_t; + +/* Fast controllers continued + */ +typedef struct fcc_c { + u32 fcc_firper; + u32 fcc_firer; + u32 fcc_firsr_hi; + u32 fcc_firsr_lo; + u8 fcc_gfemr; + u8 res1[15]; +} fcc_c_t; + +/* TC Layer + */ +typedef struct tclayer { + u16 tc_tcmode; + u16 tc_cdsmr; + u16 tc_tcer; + u16 tc_rcc; + u16 tc_tcmr; + u16 tc_fcc; + u16 tc_ccc; + u16 tc_icc; + u16 tc_tcc; + u16 tc_ecc; + u8 res1[12]; +} tclayer_t; + + +/* I2C +*/ +typedef struct i2c { + u8 i2c_i2mod; + u8 res1[3]; + u8 i2c_i2add; + u8 res2[3]; + u8 i2c_i2brg; + u8 res3[3]; + u8 i2c_i2com; + u8 res4[3]; + u8 i2c_i2cer; + u8 res5[3]; + u8 i2c_i2cmr; + u8 res6[331]; +} i2c_cpm2_t; + +typedef struct scc { /* Serial communication channels */ + u32 scc_gsmrl; + u32 scc_gsmrh; + u16 scc_psmr; + u8 res1[2]; + u16 scc_todr; + u16 scc_dsr; + u16 scc_scce; + u8 res2[2]; + u16 scc_sccm; + u8 res3; + u8 scc_sccs; + u8 res4[8]; +} scc_t; + +typedef struct smc { /* Serial management channels */ + u8 res1[2]; + u16 smc_smcmr; + u8 res2[2]; + u8 smc_smce; + u8 res3[3]; + u8 smc_smcm; + u8 res4[5]; +} smc_t; + +/* Serial Peripheral Interface. +*/ +typedef struct spi_ctrl { + u16 spi_spmode; + u8 res1[4]; + u8 spi_spie; + u8 res2[3]; + u8 spi_spim; + u8 res3[2]; + u8 spi_spcom; + u8 res4[82]; +} spictl_cpm2_t; + +/* CPM Mux. +*/ +typedef struct cpmux { + u8 cmx_si1cr; + u8 res1; + u8 cmx_si2cr; + u8 res2; + u32 cmx_fcr; + u32 cmx_scr; + u8 cmx_smr; + u8 res3; + u16 cmx_uar; + u8 res4[16]; +} cpmux_t; + +/* SIRAM control +*/ +typedef struct siram { + u16 si_amr; + u16 si_bmr; + u16 si_cmr; + u16 si_dmr; + u8 si_gmr; + u8 res1; + u8 si_cmdr; + u8 res2; + u8 si_str; + u8 res3; + u16 si_rsr; +} siramctl_t; + +typedef struct mcc { + u16 mcc_mcce; + u8 res1[2]; + u16 mcc_mccm; + u8 res2[2]; + u8 mcc_mccf; + u8 res3[7]; +} mcc_t; + +typedef struct comm_proc { + u32 cp_cpcr; + u32 cp_rccr; + u8 res1[14]; + u16 cp_rter; + u8 res2[2]; + u16 cp_rtmr; + u16 cp_rtscr; + u8 res3[2]; + u32 cp_rtsr; + u8 res4[12]; +} cpm_cpm2_t; + +/* USB Controller. +*/ +typedef struct usb_ctlr { + u8 usb_usmod; + u8 usb_usadr; + u8 usb_uscom; + u8 res1[1]; + u16 usb_usep1; + u16 usb_usep2; + u16 usb_usep3; + u16 usb_usep4; + u8 res2[4]; + u16 usb_usber; + u8 res3[2]; + u16 usb_usbmr; + u8 usb_usbs; + u8 res4[7]; +} usb_cpm2_t; + +/* ...and the whole thing wrapped up.... +*/ + +typedef struct immap { + /* Some references are into the unique and known dpram spaces, + * others are from the generic base. + */ +#define im_dprambase im_dpram1 + u8 im_dpram1[16*1024]; + u8 res1[16*1024]; + u8 im_dpram2[4*1024]; + u8 res2[8*1024]; + u8 im_dpram3[4*1024]; + u8 res3[16*1024]; + + sysconf_cpm2_t im_siu_conf; /* SIU Configuration */ + memctl_cpm2_t im_memctl; /* Memory Controller */ + sit_cpm2_t im_sit; /* System Integration Timers */ + pci_cpm2_t im_pci; /* PCI Controller */ + intctl_cpm2_t im_intctl; /* Interrupt Controller */ + car_cpm2_t im_clkrst; /* Clocks and reset */ + iop_cpm2_t im_ioport; /* IO Port control/status */ + cpmtimer_cpm2_t im_cpmtimer; /* CPM timers */ + sdma_cpm2_t im_sdma; /* SDMA control/status */ + + fcc_t im_fcc[3]; /* Three FCCs */ + u8 res4z[32]; + fcc_c_t im_fcc_c[3]; /* Continued FCCs */ + + u8 res4[32]; + + tclayer_t im_tclayer[8]; /* Eight TCLayers */ + u16 tc_tcgsr; + u16 tc_tcger; + + /* First set of baud rate generators. + */ + u8 res[236]; + u32 im_brgc5; + u32 im_brgc6; + u32 im_brgc7; + u32 im_brgc8; + + u8 res5[608]; + + i2c_cpm2_t im_i2c; /* I2C control/status */ + cpm_cpm2_t im_cpm; /* Communication processor */ + + /* Second set of baud rate generators. + */ + u32 im_brgc1; + u32 im_brgc2; + u32 im_brgc3; + u32 im_brgc4; + + scc_t im_scc[4]; /* Four SCCs */ + smc_t im_smc[2]; /* Couple of SMCs */ + spictl_cpm2_t im_spi; /* A SPI */ + cpmux_t im_cpmux; /* CPM clock route mux */ + siramctl_t im_siramctl1; /* First SI RAM Control */ + mcc_t im_mcc1; /* First MCC */ + siramctl_t im_siramctl2; /* Second SI RAM Control */ + mcc_t im_mcc2; /* Second MCC */ + usb_cpm2_t im_usb; /* USB Controller */ + + u8 res6[1153]; + + u16 im_si1txram[256]; + u8 res7[512]; + u16 im_si1rxram[256]; + u8 res8[512]; + u16 im_si2txram[256]; + u8 res9[512]; + u16 im_si2rxram[256]; + u8 res10[512]; + u8 res11[4096]; +} cpm2_map_t; + +extern cpm2_map_t *cpm2_immr; + +#endif /* __IMMAP_CPM2__ */ +#endif /* __KERNEL__ */ diff --git a/include/asm-powerpc/kgdb.h b/include/asm-powerpc/kgdb.h new file mode 100644 index 00000000000..b617dac8296 --- /dev/null +++ b/include/asm-powerpc/kgdb.h @@ -0,0 +1,57 @@ +/* + * kgdb.h: Defines and declarations for serial line source level + * remote debugging of the Linux kernel using gdb. + * + * PPC Mods (C) 1998 Michael Tesch (tesch@cs.wisc.edu) + * + * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu) + */ +#ifdef __KERNEL__ +#ifndef _PPC_KGDB_H +#define _PPC_KGDB_H + +#ifndef __ASSEMBLY__ + +/* Things specific to the gen550 backend. */ +struct uart_port; + +extern void gen550_progress(char *, unsigned short); +extern void gen550_kgdb_map_scc(void); +extern void gen550_init(int, struct uart_port *); + +/* Things specific to the pmac backend. */ +extern void zs_kgdb_hook(int tty_num); + +/* To init the kgdb engine. (called by serial hook)*/ +extern void set_debug_traps(void); + +/* To enter the debugger explicitly. */ +extern void breakpoint(void); + +/* For taking exceptions + * these are defined in traps.c + */ +extern int (*debugger)(struct pt_regs *regs); +extern int (*debugger_bpt)(struct pt_regs *regs); +extern int (*debugger_sstep)(struct pt_regs *regs); +extern int (*debugger_iabr_match)(struct pt_regs *regs); +extern int (*debugger_dabr_match)(struct pt_regs *regs); +extern void (*debugger_fault_handler)(struct pt_regs *regs); + +/* What we bring to the party */ +int kgdb_bpt(struct pt_regs *regs); +int kgdb_sstep(struct pt_regs *regs); +void kgdb(struct pt_regs *regs); +int kgdb_iabr_match(struct pt_regs *regs); +int kgdb_dabr_match(struct pt_regs *regs); + +/* + * external low-level support routines (ie macserial.c) + */ +extern void kgdb_interruptible(int); /* control interrupts from serial */ +extern void putDebugChar(char); /* write a single character */ +extern char getDebugChar(void); /* read and return a single char */ + +#endif /* !(__ASSEMBLY__) */ +#endif /* !(_PPC_KGDB_H) */ +#endif /* __KERNEL__ */ diff --git a/include/asm-powerpc/mpc52xx_psc.h b/include/asm-powerpc/mpc52xx_psc.h new file mode 100644 index 00000000000..26690d2b32f --- /dev/null +++ b/include/asm-powerpc/mpc52xx_psc.h @@ -0,0 +1,191 @@ +/* + * include/asm-ppc/mpc52xx_psc.h + * + * Definitions of consts/structs to drive the Freescale MPC52xx OnChip + * PSCs. Theses are shared between multiple drivers since a PSC can be + * UART, AC97, IR, I2S, ... So this header is in asm-ppc. + * + * + * Maintainer : Sylvain Munaut + * + * Based/Extracted from some header of the 2.4 originally written by + * Dale Farnsworth + * + * Copyright (C) 2004 Sylvain Munaut + * Copyright (C) 2003 MontaVista, Software, Inc. + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +#ifndef __ASM_MPC52xx_PSC_H__ +#define __ASM_MPC52xx_PSC_H__ + +#include + +/* Max number of PSCs */ +#define MPC52xx_PSC_MAXNUM 6 + +/* Programmable Serial Controller (PSC) status register bits */ +#define MPC52xx_PSC_SR_CDE 0x0080 +#define MPC52xx_PSC_SR_RXRDY 0x0100 +#define MPC52xx_PSC_SR_RXFULL 0x0200 +#define MPC52xx_PSC_SR_TXRDY 0x0400 +#define MPC52xx_PSC_SR_TXEMP 0x0800 +#define MPC52xx_PSC_SR_OE 0x1000 +#define MPC52xx_PSC_SR_PE 0x2000 +#define MPC52xx_PSC_SR_FE 0x4000 +#define MPC52xx_PSC_SR_RB 0x8000 + +/* PSC Command values */ +#define MPC52xx_PSC_RX_ENABLE 0x0001 +#define MPC52xx_PSC_RX_DISABLE 0x0002 +#define MPC52xx_PSC_TX_ENABLE 0x0004 +#define MPC52xx_PSC_TX_DISABLE 0x0008 +#define MPC52xx_PSC_SEL_MODE_REG_1 0x0010 +#define MPC52xx_PSC_RST_RX 0x0020 +#define MPC52xx_PSC_RST_TX 0x0030 +#define MPC52xx_PSC_RST_ERR_STAT 0x0040 +#define MPC52xx_PSC_RST_BRK_CHG_INT 0x0050 +#define MPC52xx_PSC_START_BRK 0x0060 +#define MPC52xx_PSC_STOP_BRK 0x0070 + +/* PSC TxRx FIFO status bits */ +#define MPC52xx_PSC_RXTX_FIFO_ERR 0x0040 +#define MPC52xx_PSC_RXTX_FIFO_UF 0x0020 +#define MPC52xx_PSC_RXTX_FIFO_OF 0x0010 +#define MPC52xx_PSC_RXTX_FIFO_FR 0x0008 +#define MPC52xx_PSC_RXTX_FIFO_FULL 0x0004 +#define MPC52xx_PSC_RXTX_FIFO_ALARM 0x0002 +#define MPC52xx_PSC_RXTX_FIFO_EMPTY 0x0001 + +/* PSC interrupt mask bits */ +#define MPC52xx_PSC_IMR_TXRDY 0x0100 +#define MPC52xx_PSC_IMR_RXRDY 0x0200 +#define MPC52xx_PSC_IMR_DB 0x0400 +#define MPC52xx_PSC_IMR_IPC 0x8000 + +/* PSC input port change bit */ +#define MPC52xx_PSC_CTS 0x01 +#define MPC52xx_PSC_DCD 0x02 +#define MPC52xx_PSC_D_CTS 0x10 +#define MPC52xx_PSC_D_DCD 0x20 + +/* PSC mode fields */ +#define MPC52xx_PSC_MODE_5_BITS 0x00 +#define MPC52xx_PSC_MODE_6_BITS 0x01 +#define MPC52xx_PSC_MODE_7_BITS 0x02 +#define MPC52xx_PSC_MODE_8_BITS 0x03 +#define MPC52xx_PSC_MODE_BITS_MASK 0x03 +#define MPC52xx_PSC_MODE_PAREVEN 0x00 +#define MPC52xx_PSC_MODE_PARODD 0x04 +#define MPC52xx_PSC_MODE_PARFORCE 0x08 +#define MPC52xx_PSC_MODE_PARNONE 0x10 +#define MPC52xx_PSC_MODE_ERR 0x20 +#define MPC52xx_PSC_MODE_FFULL 0x40 +#define MPC52xx_PSC_MODE_RXRTS 0x80 + +#define MPC52xx_PSC_MODE_ONE_STOP_5_BITS 0x00 +#define MPC52xx_PSC_MODE_ONE_STOP 0x07 +#define MPC52xx_PSC_MODE_TWO_STOP 0x0f + +#define MPC52xx_PSC_RFNUM_MASK 0x01ff + + +/* Structure of the hardware registers */ +struct mpc52xx_psc { + u8 mode; /* PSC + 0x00 */ + u8 reserved0[3]; + union { /* PSC + 0x04 */ + u16 status; + u16 clock_select; + } sr_csr; +#define mpc52xx_psc_status sr_csr.status +#define mpc52xx_psc_clock_select sr_csr.clock_select + u16 reserved1; + u8 command; /* PSC + 0x08 */ + u8 reserved2[3]; + union { /* PSC + 0x0c */ + u8 buffer_8; + u16 buffer_16; + u32 buffer_32; + } buffer; +#define mpc52xx_psc_buffer_8 buffer.buffer_8 +#define mpc52xx_psc_buffer_16 buffer.buffer_16 +#define mpc52xx_psc_buffer_32 buffer.buffer_32 + union { /* PSC + 0x10 */ + u8 ipcr; + u8 acr; + } ipcr_acr; +#define mpc52xx_psc_ipcr ipcr_acr.ipcr +#define mpc52xx_psc_acr ipcr_acr.acr + u8 reserved3[3]; + union { /* PSC + 0x14 */ + u16 isr; + u16 imr; + } isr_imr; +#define mpc52xx_psc_isr isr_imr.isr +#define mpc52xx_psc_imr isr_imr.imr + u16 reserved4; + u8 ctur; /* PSC + 0x18 */ + u8 reserved5[3]; + u8 ctlr; /* PSC + 0x1c */ + u8 reserved6[3]; + u16 ccr; /* PSC + 0x20 */ + u8 reserved7[14]; + u8 ivr; /* PSC + 0x30 */ + u8 reserved8[3]; + u8 ip; /* PSC + 0x34 */ + u8 reserved9[3]; + u8 op1; /* PSC + 0x38 */ + u8 reserved10[3]; + u8 op0; /* PSC + 0x3c */ + u8 reserved11[3]; + u32 sicr; /* PSC + 0x40 */ + u8 ircr1; /* PSC + 0x44 */ + u8 reserved13[3]; + u8 ircr2; /* PSC + 0x44 */ + u8 reserved14[3]; + u8 irsdr; /* PSC + 0x4c */ + u8 reserved15[3]; + u8 irmdr; /* PSC + 0x50 */ + u8 reserved16[3]; + u8 irfdr; /* PSC + 0x54 */ + u8 reserved17[3]; + u16 rfnum; /* PSC + 0x58 */ + u16 reserved18; + u16 tfnum; /* PSC + 0x5c */ + u16 reserved19; + u32 rfdata; /* PSC + 0x60 */ + u16 rfstat; /* PSC + 0x64 */ + u16 reserved20; + u8 rfcntl; /* PSC + 0x68 */ + u8 reserved21[5]; + u16 rfalarm; /* PSC + 0x6e */ + u16 reserved22; + u16 rfrptr; /* PSC + 0x72 */ + u16 reserved23; + u16 rfwptr; /* PSC + 0x76 */ + u16 reserved24; + u16 rflrfptr; /* PSC + 0x7a */ + u16 reserved25; + u16 rflwfptr; /* PSC + 0x7e */ + u32 tfdata; /* PSC + 0x80 */ + u16 tfstat; /* PSC + 0x84 */ + u16 reserved26; + u8 tfcntl; /* PSC + 0x88 */ + u8 reserved27[5]; + u16 tfalarm; /* PSC + 0x8e */ + u16 reserved28; + u16 tfrptr; /* PSC + 0x92 */ + u16 reserved29; + u16 tfwptr; /* PSC + 0x96 */ + u16 reserved30; + u16 tflrfptr; /* PSC + 0x9a */ + u16 reserved31; + u16 tflwfptr; /* PSC + 0x9e */ +}; + + +#endif /* __ASM_MPC52xx_PSC_H__ */