ath9k_hw: Implement AR9003 eeprom callbacks

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/ath/ath9k/Makefile

@@ -30,7 +30,8 @@ ath9k_hw-y:=	\
 		ani.o \
 		btcoex.o \
 		mac.o \
-		ar9003_mac.o
+		ar9003_mac.o \
+		ar9003_eeprom.o
 
 obj-$(CONFIG_ATH9K_HW) += ath9k_hw.o
 

drivers/net/wireless/ath/ath9k/ar9003_eeprom.h

@@ -0,0 +1,319 @@
+#ifndef AR9003_EEPROM_H
+#define AR9003_EEPROM_H
+
+#include <linux/types.h>
+
+#define AR9300_EEP_VER               0xD000
+#define AR9300_EEP_VER_MINOR_MASK    0xFFF
+#define AR9300_EEP_MINOR_VER_1       0x1
+#define AR9300_EEP_MINOR_VER         AR9300_EEP_MINOR_VER_1
+
+/* 16-bit offset location start of calibration struct */
+#define AR9300_EEP_START_LOC         256
+#define AR9300_NUM_5G_CAL_PIERS      8
+#define AR9300_NUM_2G_CAL_PIERS      3
+#define AR9300_NUM_5G_20_TARGET_POWERS  8
+#define AR9300_NUM_5G_40_TARGET_POWERS  8
+#define AR9300_NUM_2G_CCK_TARGET_POWERS 2
+#define AR9300_NUM_2G_20_TARGET_POWERS  3
+#define AR9300_NUM_2G_40_TARGET_POWERS  3
+/* #define AR9300_NUM_CTLS              21 */
+#define AR9300_NUM_CTLS_5G           9
+#define AR9300_NUM_CTLS_2G           12
+#define AR9300_CTL_MODE_M            0xF
+#define AR9300_NUM_BAND_EDGES_5G     8
+#define AR9300_NUM_BAND_EDGES_2G     4
+#define AR9300_NUM_PD_GAINS          4
+#define AR9300_PD_GAINS_IN_MASK      4
+#define AR9300_PD_GAIN_ICEPTS        5
+#define AR9300_EEPROM_MODAL_SPURS    5
+#define AR9300_MAX_RATE_POWER        63
+#define AR9300_NUM_PDADC_VALUES      128
+#define AR9300_NUM_RATES             16
+#define AR9300_BCHAN_UNUSED          0xFF
+#define AR9300_MAX_PWR_RANGE_IN_HALF_DB 64
+#define AR9300_OPFLAGS_11A           0x01
+#define AR9300_OPFLAGS_11G           0x02
+#define AR9300_OPFLAGS_5G_HT40       0x04
+#define AR9300_OPFLAGS_2G_HT40       0x08
+#define AR9300_OPFLAGS_5G_HT20       0x10
+#define AR9300_OPFLAGS_2G_HT20       0x20
+#define AR9300_EEPMISC_BIG_ENDIAN    0x01
+#define AR9300_EEPMISC_WOW           0x02
+#define AR9300_CUSTOMER_DATA_SIZE    20
+
+#define FREQ2FBIN(x, y) ((y) ? ((x) - 2300) : (((x) - 4800) / 5))
+#define FBIN2FREQ(x, y) ((y) ? (2300 + x) : (4800 + 5 * x))
+#define AR9300_MAX_CHAINS            3
+#define AR9300_ANT_16S               25
+#define AR9300_FUTURE_MODAL_SZ       6
+
+#define AR9300_NUM_ANT_CHAIN_FIELDS     7
+#define AR9300_NUM_ANT_COMMON_FIELDS    4
+#define AR9300_SIZE_ANT_CHAIN_FIELD     3
+#define AR9300_SIZE_ANT_COMMON_FIELD    4
+#define AR9300_ANT_CHAIN_MASK           0x7
+#define AR9300_ANT_COMMON_MASK          0xf
+#define AR9300_CHAIN_0_IDX              0
+#define AR9300_CHAIN_1_IDX              1
+#define AR9300_CHAIN_2_IDX              2
+
+#define AR928X_NUM_ANT_CHAIN_FIELDS     6
+#define AR928X_SIZE_ANT_CHAIN_FIELD     2
+#define AR928X_ANT_CHAIN_MASK           0x3
+
+/* Delta from which to start power to pdadc table */
+/* This offset is used in both open loop and closed loop power control
+ * schemes. In open loop power control, it is not really needed, but for
+ * the "sake of consistency" it was kept. For certain AP designs, this
+ * value is overwritten by the value in the flag "pwrTableOffset" just
+ * before writing the pdadc vs pwr into the chip registers.
+ */
+#define AR9300_PWR_TABLE_OFFSET  0
+
+/* enable flags for voltage and temp compensation */
+#define ENABLE_TEMP_COMPENSATION 0x01
+#define ENABLE_VOLT_COMPENSATION 0x02
+/* byte addressable */
+#define AR9300_EEPROM_SIZE (16*1024)
+#define FIXED_CCA_THRESHOLD 15
+
+#define AR9300_BASE_ADDR 0x3ff
+
+enum targetPowerHTRates {
+	HT_TARGET_RATE_0_8_16,
+	HT_TARGET_RATE_1_3_9_11_17_19,
+	HT_TARGET_RATE_4,
+	HT_TARGET_RATE_5,
+	HT_TARGET_RATE_6,
+	HT_TARGET_RATE_7,
+	HT_TARGET_RATE_12,
+	HT_TARGET_RATE_13,
+	HT_TARGET_RATE_14,
+	HT_TARGET_RATE_15,
+	HT_TARGET_RATE_20,
+	HT_TARGET_RATE_21,
+	HT_TARGET_RATE_22,
+	HT_TARGET_RATE_23
+};
+
+enum targetPowerLegacyRates {
+	LEGACY_TARGET_RATE_6_24,
+	LEGACY_TARGET_RATE_36,
+	LEGACY_TARGET_RATE_48,
+	LEGACY_TARGET_RATE_54
+};
+
+enum targetPowerCckRates {
+	LEGACY_TARGET_RATE_1L_5L,
+	LEGACY_TARGET_RATE_5S,
+	LEGACY_TARGET_RATE_11L,
+	LEGACY_TARGET_RATE_11S
+};
+
+enum ar9300_Rates {
+	ALL_TARGET_LEGACY_6_24,
+	ALL_TARGET_LEGACY_36,
+	ALL_TARGET_LEGACY_48,
+	ALL_TARGET_LEGACY_54,
+	ALL_TARGET_LEGACY_1L_5L,
+	ALL_TARGET_LEGACY_5S,
+	ALL_TARGET_LEGACY_11L,
+	ALL_TARGET_LEGACY_11S,
+	ALL_TARGET_HT20_0_8_16,
+	ALL_TARGET_HT20_1_3_9_11_17_19,
+	ALL_TARGET_HT20_4,
+	ALL_TARGET_HT20_5,
+	ALL_TARGET_HT20_6,
+	ALL_TARGET_HT20_7,
+	ALL_TARGET_HT20_12,
+	ALL_TARGET_HT20_13,
+	ALL_TARGET_HT20_14,
+	ALL_TARGET_HT20_15,
+	ALL_TARGET_HT20_20,
+	ALL_TARGET_HT20_21,
+	ALL_TARGET_HT20_22,
+	ALL_TARGET_HT20_23,
+	ALL_TARGET_HT40_0_8_16,
+	ALL_TARGET_HT40_1_3_9_11_17_19,
+	ALL_TARGET_HT40_4,
+	ALL_TARGET_HT40_5,
+	ALL_TARGET_HT40_6,
+	ALL_TARGET_HT40_7,
+	ALL_TARGET_HT40_12,
+	ALL_TARGET_HT40_13,
+	ALL_TARGET_HT40_14,
+	ALL_TARGET_HT40_15,
+	ALL_TARGET_HT40_20,
+	ALL_TARGET_HT40_21,
+	ALL_TARGET_HT40_22,
+	ALL_TARGET_HT40_23,
+	ar9300RateSize,
+};
+
+
+struct eepFlags {
+	u8 opFlags;
+	u8 eepMisc;
+} __packed;
+
+enum CompressAlgorithm {
+	_CompressNone = 0,
+	_CompressLzma,
+	_CompressPairs,
+	_CompressBlock,
+	_Compress4,
+	_Compress5,
+	_Compress6,
+	_Compress7,
+};
+
+struct ar9300_base_eep_hdr {
+	u16 regDmn[2];
+	/* 4 bits tx and 4 bits rx */
+	u8 txrxMask;
+	struct eepFlags opCapFlags;
+	u8 rfSilent;
+	u8 blueToothOptions;
+	u8 deviceCap;
+	/* takes lower byte in eeprom location */
+	u8 deviceType;
+	/* offset in dB to be added to beginning
+	 * of pdadc table in calibration
+	 */
+	int8_t pwrTableOffset;
+	u8 params_for_tuning_caps[2];
+	/*
+	 * bit0 - enable tx temp comp
+	 * bit1 - enable tx volt comp
+	 * bit2 - enable fastClock - default to 1
+	 * bit3 - enable doubling - default to 1
+	 * bit4 - enable internal regulator - default to 1
+	 */
+	u8 featureEnable;
+	/* misc flags: bit0 - turn down drivestrength */
+	u8 miscConfiguration;
+	u8 eepromWriteEnableGpio;
+	u8 wlanDisableGpio;
+	u8 wlanLedGpio;
+	u8 rxBandSelectGpio;
+	u8 txrxgain;
+	/* SW controlled internal regulator fields */
+	u32 swreg;
+} __packed;
+
+struct ar9300_modal_eep_header {
+	/* 4 idle, t1, t2, b (4 bits per setting) */
+	u32 antCtrlCommon;
+	/* 4 ra1l1, ra2l1, ra1l2, ra2l2, ra12 */
+	u32 antCtrlCommon2;
+	/* 6 idle, t, r, rx1, rx12, b (2 bits each) */
+	u16 antCtrlChain[AR9300_MAX_CHAINS];
+	/* 3 xatten1_db for AR9280 (0xa20c/b20c 5:0) */
+	u8 xatten1DB[AR9300_MAX_CHAINS];
+	/* 3  xatten1_margin for merlin (0xa20c/b20c 16:12 */
+	u8 xatten1Margin[AR9300_MAX_CHAINS];
+	int8_t tempSlope;
+	int8_t voltSlope;
+	/* spur channels in usual fbin coding format */
+	u8 spurChans[AR9300_EEPROM_MODAL_SPURS];
+	/* 3  Check if the register is per chain */
+	int8_t noiseFloorThreshCh[AR9300_MAX_CHAINS];
+	u8 ob[AR9300_MAX_CHAINS];
+	u8 db_stage2[AR9300_MAX_CHAINS];
+	u8 db_stage3[AR9300_MAX_CHAINS];
+	u8 db_stage4[AR9300_MAX_CHAINS];
+	u8 xpaBiasLvl;
+	u8 txFrameToDataStart;
+	u8 txFrameToPaOn;
+	u8 txClip;
+	int8_t antennaGain;
+	u8 switchSettling;
+	int8_t adcDesiredSize;
+	u8 txEndToXpaOff;
+	u8 txEndToRxOn;
+	u8 txFrameToXpaOn;
+	u8 thresh62;
+	u8 futureModal[32];
+} __packed;
+
+struct ar9300_cal_data_per_freq_op_loop {
+	int8_t refPower;
+	/* pdadc voltage at power measurement */
+	u8 voltMeas;
+	/* pcdac used for power measurement   */
+	u8 tempMeas;
+	/* range is -60 to -127 create a mapping equation 1db resolution */
+	int8_t rxNoisefloorCal;
+	/*range is same as noisefloor */
+	int8_t rxNoisefloorPower;
+	/* temp measured when noisefloor cal was performed */
+	u8 rxTempMeas;
+} __packed;
+
+struct cal_tgt_pow_legacy {
+	u8 tPow2x[4];
+} __packed;
+
+struct cal_tgt_pow_ht {
+	u8 tPow2x[14];
+} __packed;
+
+struct cal_ctl_edge_pwr {
+	u8 tPower:6,
+	   flag:2;
+} __packed;
+
+struct cal_ctl_data_2g {
+	struct cal_ctl_edge_pwr ctlEdges[AR9300_NUM_BAND_EDGES_5G];
+} __packed;
+
+struct cal_ctl_data_5g {
+	struct cal_ctl_edge_pwr ctlEdges[AR9300_NUM_BAND_EDGES_5G];
+} __packed;
+
+struct ar9300_eeprom {
+	u8 eepromVersion;
+	u8 templateVersion;
+	u8 macAddr[6];
+	u8 custData[AR9300_CUSTOMER_DATA_SIZE];
+
+	struct ar9300_base_eep_hdr baseEepHeader;
+
+	struct ar9300_modal_eep_header modalHeader2G;
+	u8 calFreqPier2G[AR9300_NUM_2G_CAL_PIERS];
+	struct ar9300_cal_data_per_freq_op_loop
+	 calPierData2G[AR9300_MAX_CHAINS][AR9300_NUM_2G_CAL_PIERS];
+	u8 calTarget_freqbin_Cck[AR9300_NUM_2G_CCK_TARGET_POWERS];
+	u8 calTarget_freqbin_2G[AR9300_NUM_2G_20_TARGET_POWERS];
+	u8 calTarget_freqbin_2GHT20[AR9300_NUM_2G_20_TARGET_POWERS];
+	u8 calTarget_freqbin_2GHT40[AR9300_NUM_2G_40_TARGET_POWERS];
+	struct cal_tgt_pow_legacy
+	 calTargetPowerCck[AR9300_NUM_2G_CCK_TARGET_POWERS];
+	struct cal_tgt_pow_legacy
+	 calTargetPower2G[AR9300_NUM_2G_20_TARGET_POWERS];
+	struct cal_tgt_pow_ht
+	 calTargetPower2GHT20[AR9300_NUM_2G_20_TARGET_POWERS];
+	struct cal_tgt_pow_ht
+	 calTargetPower2GHT40[AR9300_NUM_2G_40_TARGET_POWERS];
+	u8 ctlIndex_2G[AR9300_NUM_CTLS_2G];
+	u8 ctl_freqbin_2G[AR9300_NUM_CTLS_2G][AR9300_NUM_BAND_EDGES_2G];
+	struct cal_ctl_data_2g ctlPowerData_2G[AR9300_NUM_CTLS_2G];
+	struct ar9300_modal_eep_header modalHeader5G;
+	u8 calFreqPier5G[AR9300_NUM_5G_CAL_PIERS];
+	struct ar9300_cal_data_per_freq_op_loop
+	 calPierData5G[AR9300_MAX_CHAINS][AR9300_NUM_5G_CAL_PIERS];
+	u8 calTarget_freqbin_5G[AR9300_NUM_5G_20_TARGET_POWERS];
+	u8 calTarget_freqbin_5GHT20[AR9300_NUM_5G_20_TARGET_POWERS];
+	u8 calTarget_freqbin_5GHT40[AR9300_NUM_5G_40_TARGET_POWERS];
+	struct cal_tgt_pow_legacy
+	 calTargetPower5G[AR9300_NUM_5G_20_TARGET_POWERS];
+	struct cal_tgt_pow_ht
+	 calTargetPower5GHT20[AR9300_NUM_5G_20_TARGET_POWERS];
+	struct cal_tgt_pow_ht
+	 calTargetPower5GHT40[AR9300_NUM_5G_40_TARGET_POWERS];
+	u8 ctlIndex_5G[AR9300_NUM_CTLS_5G];
+	u8 ctl_freqbin_5G[AR9300_NUM_CTLS_5G][AR9300_NUM_BAND_EDGES_5G];
+	struct cal_ctl_data_5g ctlPowerData_5G[AR9300_NUM_CTLS_5G];
+} __packed;
+#endif

drivers/net/wireless/ath/ath9k/eeprom.c

@@ -256,7 +256,9 @@ int ath9k_hw_eeprom_init(struct ath_hw *ah)
 {
 	int status;
 
-	if (AR_SREV_9287(ah)) {
+	if (AR_SREV_9300_20_OR_LATER(ah))
+		ah->eep_ops = &eep_ar9300_ops;
+	else if (AR_SREV_9287(ah)) {
 		ah->eep_ops = &eep_ar9287_ops;
 	} else if (AR_SREV_9285(ah) || AR_SREV_9271(ah)) {
 		ah->eep_ops = &eep_4k_ops;

drivers/net/wireless/ath/ath9k/eeprom.h

@@ -19,6 +19,7 @@
 
 #include "../ath.h"
 #include <net/cfg80211.h>
+#include "ar9003_eeprom.h"
 
 #define AH_USE_EEPROM   0x1
 
@@ -249,16 +250,20 @@ enum eeprom_param {
 	EEP_MINOR_REV,
 	EEP_TX_MASK,
 	EEP_RX_MASK,
+	EEP_FSTCLK_5G,
 	EEP_RXGAIN_TYPE,
-	EEP_TXGAIN_TYPE,
 	EEP_OL_PWRCTRL,
+	EEP_TXGAIN_TYPE,
 	EEP_RC_CHAIN_MASK,
 	EEP_DAC_HPWR_5G,
 	EEP_FRAC_N_5G,
 	EEP_DEV_TYPE,
 	EEP_TEMPSENSE_SLOPE,
 	EEP_TEMPSENSE_SLOPE_PAL_ON,
-	EEP_PWR_TABLE_OFFSET
+	EEP_PWR_TABLE_OFFSET,
+	EEP_DRIVE_STRENGTH,
+	EEP_INTERNAL_REGULATOR,
+	EEP_SWREG
 };
 
 enum ar5416_rates {
@@ -707,5 +712,7 @@ int ath9k_hw_eeprom_init(struct ath_hw *ah);
 extern const struct eeprom_ops eep_def_ops;
 extern const struct eeprom_ops eep_4k_ops;
 extern const struct eeprom_ops eep_ar9287_ops;
+extern const struct eeprom_ops eep_ar9287_ops;
+extern const struct eeprom_ops eep_ar9300_ops;
 
 #endif /* EEPROM_H */

drivers/net/wireless/ath/ath9k/hw.h

@@ -568,6 +568,7 @@ struct ath_hw {
 		struct ar5416_eeprom_def def;
 		struct ar5416_eeprom_4k map4k;
 		struct ar9287_eeprom map9287;
+		struct ar9300_eeprom ar9300_eep;
 	} eeprom;
 	const struct eeprom_ops *eep_ops;
 

drivers/net/wireless/ath/ath9k/reg.h

@@ -1070,6 +1070,16 @@ enum {
 #define AR_RTC_RC_COLD_RESET    0x00000004
 #define AR_RTC_RC_WARM_RESET    0x00000008
 
+/* Crystal Control */
+#define AR_RTC_XTAL_CONTROL     0x7004
+
+/* Reg Control 0 */
+#define AR_RTC_REG_CONTROL0     0x7008
+
+/* Reg Control 1 */
+#define AR_RTC_REG_CONTROL1     0x700c
+#define AR_RTC_REG_CONTROL1_SWREG_PROGRAM       0x00000001
+
 #define AR_RTC_PLL_CONTROL \
 	((AR_SREV_9100(ah)) ? (AR_RTC_BASE + 0x0014) : 0x7014)
 
@@ -1100,6 +1110,7 @@ enum {
 #define AR_RTC_SLEEP_CLK \
 	((AR_SREV_9100(ah)) ? (AR_RTC_BASE + 0x0048) : 0x7048)
 #define AR_RTC_FORCE_DERIVED_CLK    0x2
+#define AR_RTC_FORCE_SWREG_PRD      0x00000004
 
 #define AR_RTC_FORCE_WAKE \
 	((AR_SREV_9100(ah)) ? (AR_RTC_BASE + 0x004c) : 0x704c)