dect
/
linux-2.6
Archived
13
0
Fork 0
Code Releases Activity
This repository has been archived on 2022-02-17. You can view files and clone it, but cannot push or open issues or pull requests.
linux-2.6/arch/arm/boot/dts/tegra20-paz00.dts

490 lines
10 KiB
Plaintext
Raw Normal View History

arm/dt: tegra: add dts file for paz00 This adds a dts file for paz00. As a side effect, this also enables the embedded controller which controls the keyboard, touchpad, power, leds, and some other functions. Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Marc Dietrich <marvin24@gmx.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2011-11-01 10:37:05 +00:00
/dts-v1/;
/include/ "tegra20.dtsi"
/ {
model = "Toshiba AC100 / Dynabook AZ";
compatible = "compal,paz00", "nvidia,tegra20";
ARM: dt: tegra: remove unnecessary unit addresses DT node names only need to include the unit address if it's required to make the node name unique. Remove the unnecessary unit addresses. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Olof Johansson <olof@lixom.net>
2012-05-11 22:17:47 +00:00
memory {
arm/dt: tegra: add dts file for paz00 This adds a dts file for paz00. As a side effect, this also enables the embedded controller which controls the keyboard, touchpad, power, leds, and some other functions. Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Marc Dietrich <marvin24@gmx.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2011-11-01 10:37:05 +00:00
reg = <0x00000000 0x20000000>;
};
ARM: dt: tegra: remove unnecessary unit addresses DT node names only need to include the unit address if it's required to make the node name unique. Remove the unnecessary unit addresses. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Olof Johansson <olof@lixom.net>
2012-05-11 22:17:47 +00:00
pinmux {
ARM: dt: tegra20: add pinmux to device tree This adds a complete pinmux configuration to all Tegra20 device tree files. This allows removal of board-dt-tegra20.c's use of the pinmux board files, and the special device tree handling in board-pinmux.c. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Olof Johansson <olof@lixom.net>
2012-03-15 22:27:36 +00:00
pinctrl-names = "default";
pinctrl-0 = <&state_default>;
state_default: pinmux {
ata {
nvidia,pins = "ata", "atc", "atd", "ate",
"dap2", "gmb", "gmc", "gmd", "spia",
"spib", "spic", "spid", "spie";
nvidia,function = "gmi";
};
atb {
nvidia,pins = "atb", "gma", "gme";
nvidia,function = "sdio4";
};
cdev1 {
nvidia,pins = "cdev1";
nvidia,function = "plla_out";
};
cdev2 {
nvidia,pins = "cdev2";
nvidia,function = "pllp_out4";
};
crtp {
nvidia,pins = "crtp";
nvidia,function = "crt";
};
csus {
nvidia,pins = "csus";
nvidia,function = "pllc_out1";
};
dap1 {
nvidia,pins = "dap1";
nvidia,function = "dap1";
};
dap3 {
nvidia,pins = "dap3";
nvidia,function = "dap3";
};
dap4 {
nvidia,pins = "dap4";
nvidia,function = "dap4";
};
ddc {
nvidia,pins = "ddc";
nvidia,function = "i2c2";
};
dta {
nvidia,pins = "dta", "dtb", "dtc", "dtd", "dte";
nvidia,function = "rsvd1";
};
dtf {
nvidia,pins = "dtf";
nvidia,function = "i2c3";
};
gpu {
nvidia,pins = "gpu", "sdb", "sdd";
nvidia,function = "pwm";
};
gpu7 {
nvidia,pins = "gpu7";
nvidia,function = "rtck";
};
gpv {
nvidia,pins = "gpv", "slxa", "slxk";
nvidia,function = "pcie";
};
hdint {
nvidia,pins = "hdint", "pta";
nvidia,function = "hdmi";
};
i2cp {
nvidia,pins = "i2cp";
nvidia,function = "i2cp";
};
irrx {
nvidia,pins = "irrx", "irtx";
nvidia,function = "uarta";
};
kbca {
nvidia,pins = "kbca", "kbcc", "kbce", "kbcf";
nvidia,function = "kbc";
};
kbcb {
nvidia,pins = "kbcb", "kbcd";
nvidia,function = "sdio2";
};
lcsn {
nvidia,pins = "lcsn", "ld0", "ld1", "ld2",
"ld3", "ld4", "ld5", "ld6", "ld7",
"ld8", "ld9", "ld10", "ld11", "ld12",
"ld13", "ld14", "ld15", "ld16", "ld17",
"ldc", "ldi", "lhp0", "lhp1", "lhp2",
"lhs", "lm0", "lm1", "lpp", "lpw0",
"lpw1", "lpw2", "lsc0", "lsc1", "lsck",
"lsda", "lsdi", "lspi", "lvp0", "lvp1",
"lvs";
nvidia,function = "displaya";
};
owc {
nvidia,pins = "owc";
nvidia,function = "owr";
};
pmc {
nvidia,pins = "pmc";
nvidia,function = "pwr_on";
};
rm {
nvidia,pins = "rm";
nvidia,function = "i2c1";
};
sdc {
nvidia,pins = "sdc";
nvidia,function = "twc";
};
sdio1 {
nvidia,pins = "sdio1";
nvidia,function = "sdio1";
};
slxc {
nvidia,pins = "slxc", "slxd";
nvidia,function = "spi4";
};
spdi {
nvidia,pins = "spdi", "spdo";
nvidia,function = "rsvd2";
};
spif {
nvidia,pins = "spif", "uac";
nvidia,function = "rsvd4";
};
spig {
nvidia,pins = "spig", "spih";
nvidia,function = "spi2_alt";
};
uaa {
nvidia,pins = "uaa", "uab", "uda";
nvidia,function = "ulpi";
};
uad {
nvidia,pins = "uad";
nvidia,function = "spdif";
};
uca {
nvidia,pins = "uca", "ucb";
nvidia,function = "uartc";
};
conf_ata {
nvidia,pins = "ata", "atb", "atc", "atd", "ate",
ARM: dt: tegra: pinmux changes for USB ULPI Ensure that the USB ULPI signals are not tri-stated, and have no pull- up or pull-down. Ensure that the pingroup hosting the USB ULPI reset signal (GPIO PV0 or PV1 depending on the board, so UAC) is not tri-stated, and has no pull- up or pull-down. This change appears larger than it is due to the grouping and sorting of the pin configuration data. Signed-off-by: Stephen Warren <swarren@nvidia.com>
2012-04-13 22:35:20 +00:00
"cdev1", "cdev2", "dap1", "dap2", "dtf",
"gma", "gmb", "gmc", "gmd", "gme",
"gpu", "gpu7", "gpv", "i2cp", "pta",
"rm", "sdio1", "slxk", "spdo", "uac",
"uda";
ARM: dt: tegra20: add pinmux to device tree This adds a complete pinmux configuration to all Tegra20 device tree files. This allows removal of board-dt-tegra20.c's use of the pinmux board files, and the special device tree handling in board-pinmux.c. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Olof Johansson <olof@lixom.net>
2012-03-15 22:27:36 +00:00
nvidia,pull = <0>;
nvidia,tristate = <0>;
};
conf_ck32 {
nvidia,pins = "ck32", "ddrc", "pmca", "pmcb",
"pmcc", "pmcd", "pmce", "xm2c", "xm2d";
nvidia,pull = <0>;
};
conf_crtp {
nvidia,pins = "crtp", "dap3", "dap4", "dtb",
"dtc", "dte", "slxa", "slxc", "slxd",
"spdi";
nvidia,pull = <0>;
nvidia,tristate = <1>;
};
conf_csus {
nvidia,pins = "csus", "spia", "spib", "spid",
"spif";
nvidia,pull = <1>;
nvidia,tristate = <1>;
};
conf_ddc {
nvidia,pins = "ddc", "irrx", "irtx", "kbca",
"kbcb", "kbcc", "kbcd", "kbce", "kbcf",
"spic", "spig", "uaa", "uab";
nvidia,pull = <2>;
nvidia,tristate = <0>;
};
conf_dta {
nvidia,pins = "dta", "dtd", "owc", "sdc", "sdd",
"spie", "spih", "uad", "uca", "ucb";
nvidia,pull = <2>;
nvidia,tristate = <1>;
};
conf_hdint {
nvidia,pins = "hdint", "ld0", "ld1", "ld2",
"ld3", "ld4", "ld5", "ld6", "ld7",
"ld8", "ld9", "ld10", "ld11", "ld12",
"ld13", "ld14", "ld15", "ld16", "ld17",
"ldc", "ldi", "lhs", "lsc0", "lspi",
"lvs", "pmc";
nvidia,tristate = <0>;
};
conf_lc {
nvidia,pins = "lc", "ls";
nvidia,pull = <2>;
};
conf_lcsn {
nvidia,pins = "lcsn", "lhp0", "lhp1", "lhp2",
"lm0", "lm1", "lpp", "lpw0", "lpw1",
"lpw2", "lsc1", "lsck", "lsda", "lsdi",
"lvp0", "lvp1", "sdb";
nvidia,tristate = <1>;
};
conf_ld17_0 {
nvidia,pins = "ld17_0", "ld19_18", "ld21_20",
"ld23_22";
nvidia,pull = <1>;
};
};
};
ARM: dt: tegra: invert status=disable vs status=okay In tegra*.dtsi, set status="disable" for all HW modules that the board design may choose not to use. Update all boards to specifically enable any of those modules that are useful by setting status="okay". This makes board files say which features they do use, rather than which they don't, which feels more logical. It also makes the .dts files slightly smaller, at least for existing content. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Olof Johansson <olof@lixom.net>
2012-05-11 23:32:56 +00:00
i2s@70002800 {
status = "okay";
ARM: dt: tegra: sort nodes based on bus order Sort the nodes according to the following rules: * First, any overrides for properties or nodes created by included files, in the order they appeared in the include file. * Second, any nodes with a reg property, in numerical order. * Third, any nodes without a reg property, in alphabetical order of node name. The second sorting rule at least will probably help if/when we need to explicitly insert nodes for the various busses in Tegra; that will just be an indentation change rather than also a node re-ordering. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Olof Johansson <olof@lixom.net>
2012-05-11 23:03:26 +00:00
};
serial@70006000 {
ARM: dt: tegra: invert status=disable vs status=okay In tegra*.dtsi, set status="disable" for all HW modules that the board design may choose not to use. Update all boards to specifically enable any of those modules that are useful by setting status="okay". This makes board files say which features they do use, rather than which they don't, which feels more logical. It also makes the .dts files slightly smaller, at least for existing content. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Olof Johansson <olof@lixom.net>
2012-05-11 23:32:56 +00:00
status = "okay";
ARM: dt: tegra: sort nodes based on bus order Sort the nodes according to the following rules: * First, any overrides for properties or nodes created by included files, in the order they appeared in the include file. * Second, any nodes with a reg property, in numerical order. * Third, any nodes without a reg property, in alphabetical order of node name. The second sorting rule at least will probably help if/when we need to explicitly insert nodes for the various busses in Tegra; that will just be an indentation change rather than also a node re-ordering. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Olof Johansson <olof@lixom.net>
2012-05-11 23:03:26 +00:00
clock-frequency = <216000000>;
};
serial@70006200 {
ARM: dt: tegra: invert status=disable vs status=okay In tegra*.dtsi, set status="disable" for all HW modules that the board design may choose not to use. Update all boards to specifically enable any of those modules that are useful by setting status="okay". This makes board files say which features they do use, rather than which they don't, which feels more logical. It also makes the .dts files slightly smaller, at least for existing content. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Olof Johansson <olof@lixom.net>
2012-05-11 23:32:56 +00:00
status = "okay";
ARM: dt: tegra: sort nodes based on bus order Sort the nodes according to the following rules: * First, any overrides for properties or nodes created by included files, in the order they appeared in the include file. * Second, any nodes with a reg property, in numerical order. * Third, any nodes without a reg property, in alphabetical order of node name. The second sorting rule at least will probably help if/when we need to explicitly insert nodes for the various busses in Tegra; that will just be an indentation change rather than also a node re-ordering. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Olof Johansson <olof@lixom.net>
2012-05-11 23:03:26 +00:00
clock-frequency = <216000000>;
};
arm/dt: tegra: add dts file for paz00 This adds a dts file for paz00. As a side effect, this also enables the embedded controller which controls the keyboard, touchpad, power, leds, and some other functions. Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Marc Dietrich <marvin24@gmx.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2011-11-01 10:37:05 +00:00
i2c@7000c000 {
ARM: dt: tegra: invert status=disable vs status=okay In tegra*.dtsi, set status="disable" for all HW modules that the board design may choose not to use. Update all boards to specifically enable any of those modules that are useful by setting status="okay". This makes board files say which features they do use, rather than which they don't, which feels more logical. It also makes the .dts files slightly smaller, at least for existing content. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Olof Johansson <olof@lixom.net>
2012-05-11 23:32:56 +00:00
status = "okay";
arm/dt: tegra: add dts file for paz00 This adds a dts file for paz00. As a side effect, this also enables the embedded controller which controls the keyboard, touchpad, power, leds, and some other functions. Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Marc Dietrich <marvin24@gmx.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2011-11-01 10:37:05 +00:00
clock-frequency = <400000>;
ARM: dt: tegra: Enable device tree audio codec on PAZ00 board. This patch adds initial device tree support of ALC5632 sound codec and machine driver for PAZ00 board. The implementation is based on the WM8903 codec. Signed-off-by: Marc Dietrich <marvin24@gmx.de> Signed-off-by: Leon Romanovsky <leon@leon.nu> Signed-off-by: Olof Johansson <olof@lixom.net>
2012-02-02 20:13:35 +00:00
alc5632: alc5632@1e {
compatible = "realtek,alc5632";
reg = <0x1e>;
gpio-controller;
#gpio-cells = <2>;
};
arm/dt: tegra: add dts file for paz00 This adds a dts file for paz00. As a side effect, this also enables the embedded controller which controls the keyboard, touchpad, power, leds, and some other functions. Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Marc Dietrich <marvin24@gmx.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2011-11-01 10:37:05 +00:00
};
i2c@7000c400 {
ARM: dt: tegra: invert status=disable vs status=okay In tegra*.dtsi, set status="disable" for all HW modules that the board design may choose not to use. Update all boards to specifically enable any of those modules that are useful by setting status="okay". This makes board files say which features they do use, rather than which they don't, which feels more logical. It also makes the .dts files slightly smaller, at least for existing content. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Olof Johansson <olof@lixom.net>
2012-05-11 23:32:56 +00:00
status = "okay";
arm/dt: tegra: add dts file for paz00 This adds a dts file for paz00. As a side effect, this also enables the embedded controller which controls the keyboard, touchpad, power, leds, and some other functions. Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Marc Dietrich <marvin24@gmx.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2011-11-01 10:37:05 +00:00
clock-frequency = <400000>;
};
ARM: dt: tegra: remove unnecessary unit addresses DT node names only need to include the unit address if it's required to make the node name unique. Remove the unnecessary unit addresses. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Olof Johansson <olof@lixom.net>
2012-05-11 22:17:47 +00:00
nvec {
arm/dt: tegra: add dts file for paz00 This adds a dts file for paz00. As a side effect, this also enables the embedded controller which controls the keyboard, touchpad, power, leds, and some other functions. Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Marc Dietrich <marvin24@gmx.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2011-11-01 10:37:05 +00:00
compatible = "nvidia,nvec";
ARM: dt: tegra: consistenly use lower-case for hex constants Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Olof Johansson <olof@lixom.net>
2012-05-11 22:28:59 +00:00
reg = <0x7000c500 0x100>;
arm/tegra: convert tegra20 to GIC devicetree binding Convert tegra20 IRQ intialization to the GIC devicetree binding. Modify the interrupt definitions in the dts files according to Documentation/devicetree/bindings/arm/gic.txt v3 (swarren): * Moved of_irq_init() call into board-dt.c to avoid ifdef'ing it. - Even with a dummy replacement if !CONFIG_OF, the reference from tegra_dt_irq_match[] to gic_of_init() would still have to be ifdef'd - It's plausible that tegra_dt_irq_match[] may need to contain more entries in the future, and defining what they are seems more suitable for board-dt.c than irq.c v2 (swarren): * Removed some stale GIC init code from board-dt.c * Undid some accidental 0x -> 0x0 search/replace. Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com> Acked-by: Rob Herring <rob.herring@calxeda.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> [olof: added include of <asm/hardware/gic.h> for compile to pass] Signed-off-by: Olof Johansson <olof@lixom.net>
2011-11-30 01:29:19 +00:00
interrupts = <0 92 0x04>;
ARM: dt: tegra: consistent basic property ordering Put properties in order compatible, reg, interrupts, then anything else the node has. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Olof Johansson <olof@lixom.net>
2012-05-11 23:12:52 +00:00
#address-cells = <1>;
#size-cells = <0>;
arm/dt: tegra: add dts file for paz00 This adds a dts file for paz00. As a side effect, this also enables the embedded controller which controls the keyboard, touchpad, power, leds, and some other functions. Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Marc Dietrich <marvin24@gmx.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2011-11-01 10:37:05 +00:00
clock-frequency = <80000>;
ARM: dt: tegra: gpio comment cleanup Ensure that all Tegraa GPIO specifiers contain a comment indicating which GPIO name the number refers to. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Olof Johansson <olof@lixom.net>
2012-05-11 22:21:10 +00:00
request-gpios = <&gpio 170 0>; /* gpio PV2 */
arm/dt: tegra: add dts file for paz00 This adds a dts file for paz00. As a side effect, this also enables the embedded controller which controls the keyboard, touchpad, power, leds, and some other functions. Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Marc Dietrich <marvin24@gmx.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2011-11-01 10:37:05 +00:00
slave-addr = <138>;
};
i2c@7000d000 {
ARM: dt: tegra: invert status=disable vs status=okay In tegra*.dtsi, set status="disable" for all HW modules that the board design may choose not to use. Update all boards to specifically enable any of those modules that are useful by setting status="okay". This makes board files say which features they do use, rather than which they don't, which feels more logical. It also makes the .dts files slightly smaller, at least for existing content. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Olof Johansson <olof@lixom.net>
2012-05-11 23:32:56 +00:00
status = "okay";
arm/dt: tegra: add dts file for paz00 This adds a dts file for paz00. As a side effect, this also enables the embedded controller which controls the keyboard, touchpad, power, leds, and some other functions. Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Marc Dietrich <marvin24@gmx.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2011-11-01 10:37:05 +00:00
clock-frequency = <400000>;
ARM: dt: tegra: add ADT7461 temperature sensor to paz00 device tree Add the ADT7461 temperature monitoring IC which is connected via the DVC controller. Signed-off-by: Marc Dietrich <marvin24@gmx.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2012-01-31 18:53:21 +00:00
ARM: dt: tegra: paz00: add regulators The Toshiba AC100/PAZ00 uses a TPS6586x regulator. Instantiate this. Three data sources were used for the data encoded here: * The HW defaults, as extracted from real HW. * The schematic, which specifies a voltage for each rail in the signal names. * The AC100 kernel used by the Ubuntu port: repo git://gitorious.org/~marvin24/ac100/marvin24s-kernel.git branch chromeos-ac100-3.0 file arch/arm/mach-tegra/board-paz00-power.c For many rails, the constraints in that tree specified differing min and max voltages. In all cases, the min value was ignored, since there's no need currently to vary any of the voltages at run-time. DVFS might change this in the future. In most cases these sources all matched. Differences are: sm0: HW defaults and schematic match at 1.2v. marvin24's kernel had a max of 1.3v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. sm1: HW defaults and schematic match at 1.0v. marvin24's kernel had a max of 1.125v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. ldo3: The HW default is on. marvin24's kernel didn't specify always-on, but since the board wasn't marked as having fully constrained regulators, the rail was not turned off, so the difference had no effect. The rail is needed for USB. ldo6: The HW default is 2.85v. The schematics indicate 2.85v. However, since this regulator is used for the same purpose as on other boards that require 1.8v, this is set to 1.8v. Note that this regulator feeds the CRT VDAC on Tegra, and so in practice is unlikely to be used, even though it is actaully hooked up in HW. Portions based on work by Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Tested-by: Marc Dietrich <marvin24@gmx.de> # v2 Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
2012-06-21 20:24:57 +00:00
pmic: tps6586x@34 {
compatible = "ti,tps6586x";
reg = <0x34>;
interrupts = <0 86 0x4>;
#gpio-cells = <2>;
gpio-controller;
sys-supply = <&p5valw_reg>;
vin-sm0-supply = <&sys_reg>;
vin-sm1-supply = <&sys_reg>;
vin-sm2-supply = <&sys_reg>;
vinldo01-supply = <&sm2_reg>;
vinldo23-supply = <&sm2_reg>;
vinldo4-supply = <&sm2_reg>;
vinldo678-supply = <&sm2_reg>;
vinldo9-supply = <&sm2_reg>;
regulators {
ARM: tegra: update *.dts for regulator-compatible deprecation Commit 13511de "regulator: deprecate regulator-compatible DT property" now allows for simpler content within the regulators node within a PMIC. Modify all the Tegra device tree files to take advantage of this. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-09-20 23:04:06 +00:00
sys_reg: sys {
ARM: dt: tegra: paz00: add regulators The Toshiba AC100/PAZ00 uses a TPS6586x regulator. Instantiate this. Three data sources were used for the data encoded here: * The HW defaults, as extracted from real HW. * The schematic, which specifies a voltage for each rail in the signal names. * The AC100 kernel used by the Ubuntu port: repo git://gitorious.org/~marvin24/ac100/marvin24s-kernel.git branch chromeos-ac100-3.0 file arch/arm/mach-tegra/board-paz00-power.c For many rails, the constraints in that tree specified differing min and max voltages. In all cases, the min value was ignored, since there's no need currently to vary any of the voltages at run-time. DVFS might change this in the future. In most cases these sources all matched. Differences are: sm0: HW defaults and schematic match at 1.2v. marvin24's kernel had a max of 1.3v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. sm1: HW defaults and schematic match at 1.0v. marvin24's kernel had a max of 1.125v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. ldo3: The HW default is on. marvin24's kernel didn't specify always-on, but since the board wasn't marked as having fully constrained regulators, the rail was not turned off, so the difference had no effect. The rail is needed for USB. ldo6: The HW default is 2.85v. The schematics indicate 2.85v. However, since this regulator is used for the same purpose as on other boards that require 1.8v, this is set to 1.8v. Note that this regulator feeds the CRT VDAC on Tegra, and so in practice is unlikely to be used, even though it is actaully hooked up in HW. Portions based on work by Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Tested-by: Marc Dietrich <marvin24@gmx.de> # v2 Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
2012-06-21 20:24:57 +00:00
regulator-name = "vdd_sys";
regulator-always-on;
};
ARM: tegra: update *.dts for regulator-compatible deprecation Commit 13511de "regulator: deprecate regulator-compatible DT property" now allows for simpler content within the regulators node within a PMIC. Modify all the Tegra device tree files to take advantage of this. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-09-20 23:04:06 +00:00
sm0 {
ARM: dt: tegra: paz00: add regulators The Toshiba AC100/PAZ00 uses a TPS6586x regulator. Instantiate this. Three data sources were used for the data encoded here: * The HW defaults, as extracted from real HW. * The schematic, which specifies a voltage for each rail in the signal names. * The AC100 kernel used by the Ubuntu port: repo git://gitorious.org/~marvin24/ac100/marvin24s-kernel.git branch chromeos-ac100-3.0 file arch/arm/mach-tegra/board-paz00-power.c For many rails, the constraints in that tree specified differing min and max voltages. In all cases, the min value was ignored, since there's no need currently to vary any of the voltages at run-time. DVFS might change this in the future. In most cases these sources all matched. Differences are: sm0: HW defaults and schematic match at 1.2v. marvin24's kernel had a max of 1.3v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. sm1: HW defaults and schematic match at 1.0v. marvin24's kernel had a max of 1.125v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. ldo3: The HW default is on. marvin24's kernel didn't specify always-on, but since the board wasn't marked as having fully constrained regulators, the rail was not turned off, so the difference had no effect. The rail is needed for USB. ldo6: The HW default is 2.85v. The schematics indicate 2.85v. However, since this regulator is used for the same purpose as on other boards that require 1.8v, this is set to 1.8v. Note that this regulator feeds the CRT VDAC on Tegra, and so in practice is unlikely to be used, even though it is actaully hooked up in HW. Portions based on work by Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Tested-by: Marc Dietrich <marvin24@gmx.de> # v2 Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
2012-06-21 20:24:57 +00:00
regulator-name = "+1.2vs_sm0,vdd_core";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-always-on;
};
ARM: tegra: update *.dts for regulator-compatible deprecation Commit 13511de "regulator: deprecate regulator-compatible DT property" now allows for simpler content within the regulators node within a PMIC. Modify all the Tegra device tree files to take advantage of this. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-09-20 23:04:06 +00:00
sm1 {
ARM: dt: tegra: paz00: add regulators The Toshiba AC100/PAZ00 uses a TPS6586x regulator. Instantiate this. Three data sources were used for the data encoded here: * The HW defaults, as extracted from real HW. * The schematic, which specifies a voltage for each rail in the signal names. * The AC100 kernel used by the Ubuntu port: repo git://gitorious.org/~marvin24/ac100/marvin24s-kernel.git branch chromeos-ac100-3.0 file arch/arm/mach-tegra/board-paz00-power.c For many rails, the constraints in that tree specified differing min and max voltages. In all cases, the min value was ignored, since there's no need currently to vary any of the voltages at run-time. DVFS might change this in the future. In most cases these sources all matched. Differences are: sm0: HW defaults and schematic match at 1.2v. marvin24's kernel had a max of 1.3v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. sm1: HW defaults and schematic match at 1.0v. marvin24's kernel had a max of 1.125v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. ldo3: The HW default is on. marvin24's kernel didn't specify always-on, but since the board wasn't marked as having fully constrained regulators, the rail was not turned off, so the difference had no effect. The rail is needed for USB. ldo6: The HW default is 2.85v. The schematics indicate 2.85v. However, since this regulator is used for the same purpose as on other boards that require 1.8v, this is set to 1.8v. Note that this regulator feeds the CRT VDAC on Tegra, and so in practice is unlikely to be used, even though it is actaully hooked up in HW. Portions based on work by Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Tested-by: Marc Dietrich <marvin24@gmx.de> # v2 Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
2012-06-21 20:24:57 +00:00
regulator-name = "+1.0vs_sm1,vdd_cpu";
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-always-on;
};
ARM: tegra: update *.dts for regulator-compatible deprecation Commit 13511de "regulator: deprecate regulator-compatible DT property" now allows for simpler content within the regulators node within a PMIC. Modify all the Tegra device tree files to take advantage of this. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-09-20 23:04:06 +00:00
sm2_reg: sm2 {
ARM: dt: tegra: paz00: add regulators The Toshiba AC100/PAZ00 uses a TPS6586x regulator. Instantiate this. Three data sources were used for the data encoded here: * The HW defaults, as extracted from real HW. * The schematic, which specifies a voltage for each rail in the signal names. * The AC100 kernel used by the Ubuntu port: repo git://gitorious.org/~marvin24/ac100/marvin24s-kernel.git branch chromeos-ac100-3.0 file arch/arm/mach-tegra/board-paz00-power.c For many rails, the constraints in that tree specified differing min and max voltages. In all cases, the min value was ignored, since there's no need currently to vary any of the voltages at run-time. DVFS might change this in the future. In most cases these sources all matched. Differences are: sm0: HW defaults and schematic match at 1.2v. marvin24's kernel had a max of 1.3v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. sm1: HW defaults and schematic match at 1.0v. marvin24's kernel had a max of 1.125v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. ldo3: The HW default is on. marvin24's kernel didn't specify always-on, but since the board wasn't marked as having fully constrained regulators, the rail was not turned off, so the difference had no effect. The rail is needed for USB. ldo6: The HW default is 2.85v. The schematics indicate 2.85v. However, since this regulator is used for the same purpose as on other boards that require 1.8v, this is set to 1.8v. Note that this regulator feeds the CRT VDAC on Tegra, and so in practice is unlikely to be used, even though it is actaully hooked up in HW. Portions based on work by Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Tested-by: Marc Dietrich <marvin24@gmx.de> # v2 Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
2012-06-21 20:24:57 +00:00
regulator-name = "+3.7vs_sm2,vin_ldo*";
regulator-min-microvolt = <3700000>;
regulator-max-microvolt = <3700000>;
regulator-always-on;
};
/* LDO0 is not connected to anything */
ARM: tegra: update *.dts for regulator-compatible deprecation Commit 13511de "regulator: deprecate regulator-compatible DT property" now allows for simpler content within the regulators node within a PMIC. Modify all the Tegra device tree files to take advantage of this. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-09-20 23:04:06 +00:00
ldo1 {
ARM: dt: tegra: paz00: add regulators The Toshiba AC100/PAZ00 uses a TPS6586x regulator. Instantiate this. Three data sources were used for the data encoded here: * The HW defaults, as extracted from real HW. * The schematic, which specifies a voltage for each rail in the signal names. * The AC100 kernel used by the Ubuntu port: repo git://gitorious.org/~marvin24/ac100/marvin24s-kernel.git branch chromeos-ac100-3.0 file arch/arm/mach-tegra/board-paz00-power.c For many rails, the constraints in that tree specified differing min and max voltages. In all cases, the min value was ignored, since there's no need currently to vary any of the voltages at run-time. DVFS might change this in the future. In most cases these sources all matched. Differences are: sm0: HW defaults and schematic match at 1.2v. marvin24's kernel had a max of 1.3v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. sm1: HW defaults and schematic match at 1.0v. marvin24's kernel had a max of 1.125v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. ldo3: The HW default is on. marvin24's kernel didn't specify always-on, but since the board wasn't marked as having fully constrained regulators, the rail was not turned off, so the difference had no effect. The rail is needed for USB. ldo6: The HW default is 2.85v. The schematics indicate 2.85v. However, since this regulator is used for the same purpose as on other boards that require 1.8v, this is set to 1.8v. Note that this regulator feeds the CRT VDAC on Tegra, and so in practice is unlikely to be used, even though it is actaully hooked up in HW. Portions based on work by Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Tested-by: Marc Dietrich <marvin24@gmx.de> # v2 Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
2012-06-21 20:24:57 +00:00
regulator-name = "+1.1vs_ldo1,avdd_pll*";
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
regulator-always-on;
};
ARM: tegra: update *.dts for regulator-compatible deprecation Commit 13511de "regulator: deprecate regulator-compatible DT property" now allows for simpler content within the regulators node within a PMIC. Modify all the Tegra device tree files to take advantage of this. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-09-20 23:04:06 +00:00
ldo2 {
ARM: dt: tegra: paz00: add regulators The Toshiba AC100/PAZ00 uses a TPS6586x regulator. Instantiate this. Three data sources were used for the data encoded here: * The HW defaults, as extracted from real HW. * The schematic, which specifies a voltage for each rail in the signal names. * The AC100 kernel used by the Ubuntu port: repo git://gitorious.org/~marvin24/ac100/marvin24s-kernel.git branch chromeos-ac100-3.0 file arch/arm/mach-tegra/board-paz00-power.c For many rails, the constraints in that tree specified differing min and max voltages. In all cases, the min value was ignored, since there's no need currently to vary any of the voltages at run-time. DVFS might change this in the future. In most cases these sources all matched. Differences are: sm0: HW defaults and schematic match at 1.2v. marvin24's kernel had a max of 1.3v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. sm1: HW defaults and schematic match at 1.0v. marvin24's kernel had a max of 1.125v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. ldo3: The HW default is on. marvin24's kernel didn't specify always-on, but since the board wasn't marked as having fully constrained regulators, the rail was not turned off, so the difference had no effect. The rail is needed for USB. ldo6: The HW default is 2.85v. The schematics indicate 2.85v. However, since this regulator is used for the same purpose as on other boards that require 1.8v, this is set to 1.8v. Note that this regulator feeds the CRT VDAC on Tegra, and so in practice is unlikely to be used, even though it is actaully hooked up in HW. Portions based on work by Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Tested-by: Marc Dietrich <marvin24@gmx.de> # v2 Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
2012-06-21 20:24:57 +00:00
regulator-name = "+1.2vs_ldo2,vdd_rtc";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
};
ARM: tegra: update *.dts for regulator-compatible deprecation Commit 13511de "regulator: deprecate regulator-compatible DT property" now allows for simpler content within the regulators node within a PMIC. Modify all the Tegra device tree files to take advantage of this. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-09-20 23:04:06 +00:00
ldo3 {
ARM: dt: tegra: paz00: add regulators The Toshiba AC100/PAZ00 uses a TPS6586x regulator. Instantiate this. Three data sources were used for the data encoded here: * The HW defaults, as extracted from real HW. * The schematic, which specifies a voltage for each rail in the signal names. * The AC100 kernel used by the Ubuntu port: repo git://gitorious.org/~marvin24/ac100/marvin24s-kernel.git branch chromeos-ac100-3.0 file arch/arm/mach-tegra/board-paz00-power.c For many rails, the constraints in that tree specified differing min and max voltages. In all cases, the min value was ignored, since there's no need currently to vary any of the voltages at run-time. DVFS might change this in the future. In most cases these sources all matched. Differences are: sm0: HW defaults and schematic match at 1.2v. marvin24's kernel had a max of 1.3v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. sm1: HW defaults and schematic match at 1.0v. marvin24's kernel had a max of 1.125v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. ldo3: The HW default is on. marvin24's kernel didn't specify always-on, but since the board wasn't marked as having fully constrained regulators, the rail was not turned off, so the difference had no effect. The rail is needed for USB. ldo6: The HW default is 2.85v. The schematics indicate 2.85v. However, since this regulator is used for the same purpose as on other boards that require 1.8v, this is set to 1.8v. Note that this regulator feeds the CRT VDAC on Tegra, and so in practice is unlikely to be used, even though it is actaully hooked up in HW. Portions based on work by Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Tested-by: Marc Dietrich <marvin24@gmx.de> # v2 Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
2012-06-21 20:24:57 +00:00
regulator-name = "+3.3vs_ldo3,avdd_usb*";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
ARM: tegra: update *.dts for regulator-compatible deprecation Commit 13511de "regulator: deprecate regulator-compatible DT property" now allows for simpler content within the regulators node within a PMIC. Modify all the Tegra device tree files to take advantage of this. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-09-20 23:04:06 +00:00
ldo4 {
ARM: dt: tegra: paz00: add regulators The Toshiba AC100/PAZ00 uses a TPS6586x regulator. Instantiate this. Three data sources were used for the data encoded here: * The HW defaults, as extracted from real HW. * The schematic, which specifies a voltage for each rail in the signal names. * The AC100 kernel used by the Ubuntu port: repo git://gitorious.org/~marvin24/ac100/marvin24s-kernel.git branch chromeos-ac100-3.0 file arch/arm/mach-tegra/board-paz00-power.c For many rails, the constraints in that tree specified differing min and max voltages. In all cases, the min value was ignored, since there's no need currently to vary any of the voltages at run-time. DVFS might change this in the future. In most cases these sources all matched. Differences are: sm0: HW defaults and schematic match at 1.2v. marvin24's kernel had a max of 1.3v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. sm1: HW defaults and schematic match at 1.0v. marvin24's kernel had a max of 1.125v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. ldo3: The HW default is on. marvin24's kernel didn't specify always-on, but since the board wasn't marked as having fully constrained regulators, the rail was not turned off, so the difference had no effect. The rail is needed for USB. ldo6: The HW default is 2.85v. The schematics indicate 2.85v. However, since this regulator is used for the same purpose as on other boards that require 1.8v, this is set to 1.8v. Note that this regulator feeds the CRT VDAC on Tegra, and so in practice is unlikely to be used, even though it is actaully hooked up in HW. Portions based on work by Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Tested-by: Marc Dietrich <marvin24@gmx.de> # v2 Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
2012-06-21 20:24:57 +00:00
regulator-name = "+1.8vs_ldo4,avdd_osc,vddio_sys";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
ARM: tegra: update *.dts for regulator-compatible deprecation Commit 13511de "regulator: deprecate regulator-compatible DT property" now allows for simpler content within the regulators node within a PMIC. Modify all the Tegra device tree files to take advantage of this. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-09-20 23:04:06 +00:00
ldo5 {
ARM: dt: tegra: paz00: add regulators The Toshiba AC100/PAZ00 uses a TPS6586x regulator. Instantiate this. Three data sources were used for the data encoded here: * The HW defaults, as extracted from real HW. * The schematic, which specifies a voltage for each rail in the signal names. * The AC100 kernel used by the Ubuntu port: repo git://gitorious.org/~marvin24/ac100/marvin24s-kernel.git branch chromeos-ac100-3.0 file arch/arm/mach-tegra/board-paz00-power.c For many rails, the constraints in that tree specified differing min and max voltages. In all cases, the min value was ignored, since there's no need currently to vary any of the voltages at run-time. DVFS might change this in the future. In most cases these sources all matched. Differences are: sm0: HW defaults and schematic match at 1.2v. marvin24's kernel had a max of 1.3v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. sm1: HW defaults and schematic match at 1.0v. marvin24's kernel had a max of 1.125v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. ldo3: The HW default is on. marvin24's kernel didn't specify always-on, but since the board wasn't marked as having fully constrained regulators, the rail was not turned off, so the difference had no effect. The rail is needed for USB. ldo6: The HW default is 2.85v. The schematics indicate 2.85v. However, since this regulator is used for the same purpose as on other boards that require 1.8v, this is set to 1.8v. Note that this regulator feeds the CRT VDAC on Tegra, and so in practice is unlikely to be used, even though it is actaully hooked up in HW. Portions based on work by Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Tested-by: Marc Dietrich <marvin24@gmx.de> # v2 Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
2012-06-21 20:24:57 +00:00
regulator-name = "+2.85vs_ldo5,vcore_mmc";
regulator-min-microvolt = <2850000>;
regulator-max-microvolt = <2850000>;
regulator-always-on;
};
ARM: tegra: update *.dts for regulator-compatible deprecation Commit 13511de "regulator: deprecate regulator-compatible DT property" now allows for simpler content within the regulators node within a PMIC. Modify all the Tegra device tree files to take advantage of this. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-09-20 23:04:06 +00:00
ldo6 {
ARM: dt: tegra: paz00: add regulators The Toshiba AC100/PAZ00 uses a TPS6586x regulator. Instantiate this. Three data sources were used for the data encoded here: * The HW defaults, as extracted from real HW. * The schematic, which specifies a voltage for each rail in the signal names. * The AC100 kernel used by the Ubuntu port: repo git://gitorious.org/~marvin24/ac100/marvin24s-kernel.git branch chromeos-ac100-3.0 file arch/arm/mach-tegra/board-paz00-power.c For many rails, the constraints in that tree specified differing min and max voltages. In all cases, the min value was ignored, since there's no need currently to vary any of the voltages at run-time. DVFS might change this in the future. In most cases these sources all matched. Differences are: sm0: HW defaults and schematic match at 1.2v. marvin24's kernel had a max of 1.3v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. sm1: HW defaults and schematic match at 1.0v. marvin24's kernel had a max of 1.125v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. ldo3: The HW default is on. marvin24's kernel didn't specify always-on, but since the board wasn't marked as having fully constrained regulators, the rail was not turned off, so the difference had no effect. The rail is needed for USB. ldo6: The HW default is 2.85v. The schematics indicate 2.85v. However, since this regulator is used for the same purpose as on other boards that require 1.8v, this is set to 1.8v. Note that this regulator feeds the CRT VDAC on Tegra, and so in practice is unlikely to be used, even though it is actaully hooked up in HW. Portions based on work by Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Tested-by: Marc Dietrich <marvin24@gmx.de> # v2 Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
2012-06-21 20:24:57 +00:00
/*
* Research indicates this should be
* 1.8v; other boards that use this
* rail for the same purpose need it
* set to 1.8v. The schematic signal
* name is incorrect; perhaps copied
* from an incorrect NVIDIA reference.
*/
regulator-name = "+2.85vs_ldo6,avdd_vdac";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
ARM: tegra: update *.dts for regulator-compatible deprecation Commit 13511de "regulator: deprecate regulator-compatible DT property" now allows for simpler content within the regulators node within a PMIC. Modify all the Tegra device tree files to take advantage of this. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-09-20 23:04:06 +00:00
ldo7 {
ARM: dt: tegra: paz00: add regulators The Toshiba AC100/PAZ00 uses a TPS6586x regulator. Instantiate this. Three data sources were used for the data encoded here: * The HW defaults, as extracted from real HW. * The schematic, which specifies a voltage for each rail in the signal names. * The AC100 kernel used by the Ubuntu port: repo git://gitorious.org/~marvin24/ac100/marvin24s-kernel.git branch chromeos-ac100-3.0 file arch/arm/mach-tegra/board-paz00-power.c For many rails, the constraints in that tree specified differing min and max voltages. In all cases, the min value was ignored, since there's no need currently to vary any of the voltages at run-time. DVFS might change this in the future. In most cases these sources all matched. Differences are: sm0: HW defaults and schematic match at 1.2v. marvin24's kernel had a max of 1.3v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. sm1: HW defaults and schematic match at 1.0v. marvin24's kernel had a max of 1.125v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. ldo3: The HW default is on. marvin24's kernel didn't specify always-on, but since the board wasn't marked as having fully constrained regulators, the rail was not turned off, so the difference had no effect. The rail is needed for USB. ldo6: The HW default is 2.85v. The schematics indicate 2.85v. However, since this regulator is used for the same purpose as on other boards that require 1.8v, this is set to 1.8v. Note that this regulator feeds the CRT VDAC on Tegra, and so in practice is unlikely to be used, even though it is actaully hooked up in HW. Portions based on work by Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Tested-by: Marc Dietrich <marvin24@gmx.de> # v2 Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
2012-06-21 20:24:57 +00:00
regulator-name = "+3.3vs_ldo7,avdd_hdmi";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
ARM: tegra: update *.dts for regulator-compatible deprecation Commit 13511de "regulator: deprecate regulator-compatible DT property" now allows for simpler content within the regulators node within a PMIC. Modify all the Tegra device tree files to take advantage of this. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-09-20 23:04:06 +00:00
ldo8 {
ARM: dt: tegra: paz00: add regulators The Toshiba AC100/PAZ00 uses a TPS6586x regulator. Instantiate this. Three data sources were used for the data encoded here: * The HW defaults, as extracted from real HW. * The schematic, which specifies a voltage for each rail in the signal names. * The AC100 kernel used by the Ubuntu port: repo git://gitorious.org/~marvin24/ac100/marvin24s-kernel.git branch chromeos-ac100-3.0 file arch/arm/mach-tegra/board-paz00-power.c For many rails, the constraints in that tree specified differing min and max voltages. In all cases, the min value was ignored, since there's no need currently to vary any of the voltages at run-time. DVFS might change this in the future. In most cases these sources all matched. Differences are: sm0: HW defaults and schematic match at 1.2v. marvin24's kernel had a max of 1.3v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. sm1: HW defaults and schematic match at 1.0v. marvin24's kernel had a max of 1.125v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. ldo3: The HW default is on. marvin24's kernel didn't specify always-on, but since the board wasn't marked as having fully constrained regulators, the rail was not turned off, so the difference had no effect. The rail is needed for USB. ldo6: The HW default is 2.85v. The schematics indicate 2.85v. However, since this regulator is used for the same purpose as on other boards that require 1.8v, this is set to 1.8v. Note that this regulator feeds the CRT VDAC on Tegra, and so in practice is unlikely to be used, even though it is actaully hooked up in HW. Portions based on work by Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Tested-by: Marc Dietrich <marvin24@gmx.de> # v2 Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
2012-06-21 20:24:57 +00:00
regulator-name = "+1.8vs_ldo8,avdd_hdmi_pll";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
ARM: tegra: update *.dts for regulator-compatible deprecation Commit 13511de "regulator: deprecate regulator-compatible DT property" now allows for simpler content within the regulators node within a PMIC. Modify all the Tegra device tree files to take advantage of this. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-09-20 23:04:06 +00:00
ldo9 {
ARM: dt: tegra: paz00: add regulators The Toshiba AC100/PAZ00 uses a TPS6586x regulator. Instantiate this. Three data sources were used for the data encoded here: * The HW defaults, as extracted from real HW. * The schematic, which specifies a voltage for each rail in the signal names. * The AC100 kernel used by the Ubuntu port: repo git://gitorious.org/~marvin24/ac100/marvin24s-kernel.git branch chromeos-ac100-3.0 file arch/arm/mach-tegra/board-paz00-power.c For many rails, the constraints in that tree specified differing min and max voltages. In all cases, the min value was ignored, since there's no need currently to vary any of the voltages at run-time. DVFS might change this in the future. In most cases these sources all matched. Differences are: sm0: HW defaults and schematic match at 1.2v. marvin24's kernel had a max of 1.3v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. sm1: HW defaults and schematic match at 1.0v. marvin24's kernel had a max of 1.125v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. ldo3: The HW default is on. marvin24's kernel didn't specify always-on, but since the board wasn't marked as having fully constrained regulators, the rail was not turned off, so the difference had no effect. The rail is needed for USB. ldo6: The HW default is 2.85v. The schematics indicate 2.85v. However, since this regulator is used for the same purpose as on other boards that require 1.8v, this is set to 1.8v. Note that this regulator feeds the CRT VDAC on Tegra, and so in practice is unlikely to be used, even though it is actaully hooked up in HW. Portions based on work by Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Tested-by: Marc Dietrich <marvin24@gmx.de> # v2 Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
2012-06-21 20:24:57 +00:00
regulator-name = "+2.85vs_ldo9,vdd_ddr_rx";
regulator-min-microvolt = <2850000>;
regulator-max-microvolt = <2850000>;
regulator-always-on;
};
ARM: tegra: update *.dts for regulator-compatible deprecation Commit 13511de "regulator: deprecate regulator-compatible DT property" now allows for simpler content within the regulators node within a PMIC. Modify all the Tegra device tree files to take advantage of this. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-09-20 23:04:06 +00:00
ldo_rtc {
ARM: dt: tegra: paz00: add regulators The Toshiba AC100/PAZ00 uses a TPS6586x regulator. Instantiate this. Three data sources were used for the data encoded here: * The HW defaults, as extracted from real HW. * The schematic, which specifies a voltage for each rail in the signal names. * The AC100 kernel used by the Ubuntu port: repo git://gitorious.org/~marvin24/ac100/marvin24s-kernel.git branch chromeos-ac100-3.0 file arch/arm/mach-tegra/board-paz00-power.c For many rails, the constraints in that tree specified differing min and max voltages. In all cases, the min value was ignored, since there's no need currently to vary any of the voltages at run-time. DVFS might change this in the future. In most cases these sources all matched. Differences are: sm0: HW defaults and schematic match at 1.2v. marvin24's kernel had a max of 1.3v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. sm1: HW defaults and schematic match at 1.0v. marvin24's kernel had a max of 1.125v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. ldo3: The HW default is on. marvin24's kernel didn't specify always-on, but since the board wasn't marked as having fully constrained regulators, the rail was not turned off, so the difference had no effect. The rail is needed for USB. ldo6: The HW default is 2.85v. The schematics indicate 2.85v. However, since this regulator is used for the same purpose as on other boards that require 1.8v, this is set to 1.8v. Note that this regulator feeds the CRT VDAC on Tegra, and so in practice is unlikely to be used, even though it is actaully hooked up in HW. Portions based on work by Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Tested-by: Marc Dietrich <marvin24@gmx.de> # v2 Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
2012-06-21 20:24:57 +00:00
regulator-name = "+3.3vs_rtc";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
};
};
ARM: dt: tegra: add ADT7461 temperature sensor to paz00 device tree Add the ADT7461 temperature monitoring IC which is connected via the DVC controller. Signed-off-by: Marc Dietrich <marvin24@gmx.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2012-01-31 18:53:21 +00:00
adt7461@4c {
compatible = "adi,adt7461";
reg = <0x4c>;
};
arm/dt: tegra: add dts file for paz00 This adds a dts file for paz00. As a side effect, this also enables the embedded controller which controls the keyboard, touchpad, power, leds, and some other functions. Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Marc Dietrich <marvin24@gmx.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2011-11-01 10:37:05 +00:00
};
ARM: dt: tegra: paz00: add regulators The Toshiba AC100/PAZ00 uses a TPS6586x regulator. Instantiate this. Three data sources were used for the data encoded here: * The HW defaults, as extracted from real HW. * The schematic, which specifies a voltage for each rail in the signal names. * The AC100 kernel used by the Ubuntu port: repo git://gitorious.org/~marvin24/ac100/marvin24s-kernel.git branch chromeos-ac100-3.0 file arch/arm/mach-tegra/board-paz00-power.c For many rails, the constraints in that tree specified differing min and max voltages. In all cases, the min value was ignored, since there's no need currently to vary any of the voltages at run-time. DVFS might change this in the future. In most cases these sources all matched. Differences are: sm0: HW defaults and schematic match at 1.2v. marvin24's kernel had a max of 1.3v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. sm1: HW defaults and schematic match at 1.0v. marvin24's kernel had a max of 1.125v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. ldo3: The HW default is on. marvin24's kernel didn't specify always-on, but since the board wasn't marked as having fully constrained regulators, the rail was not turned off, so the difference had no effect. The rail is needed for USB. ldo6: The HW default is 2.85v. The schematics indicate 2.85v. However, since this regulator is used for the same purpose as on other boards that require 1.8v, this is set to 1.8v. Note that this regulator feeds the CRT VDAC on Tegra, and so in practice is unlikely to be used, even though it is actaully hooked up in HW. Portions based on work by Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Tested-by: Marc Dietrich <marvin24@gmx.de> # v2 Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
2012-06-21 20:24:57 +00:00
pmc {
nvidia,invert-interrupt;
};
ARM: dt: tegra: invert status=disable vs status=okay In tegra*.dtsi, set status="disable" for all HW modules that the board design may choose not to use. Update all boards to specifically enable any of those modules that are useful by setting status="okay". This makes board files say which features they do use, rather than which they don't, which feels more logical. It also makes the .dts files slightly smaller, at least for existing content. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Olof Johansson <olof@lixom.net>
2012-05-11 23:32:56 +00:00
usb@c5000000 {
status = "okay";
};
ARM: dt: tegra: sort nodes based on bus order Sort the nodes according to the following rules: * First, any overrides for properties or nodes created by included files, in the order they appeared in the include file. * Second, any nodes with a reg property, in numerical order. * Third, any nodes without a reg property, in alphabetical order of node name. The second sorting rule at least will probably help if/when we need to explicitly insert nodes for the various busses in Tegra; that will just be an indentation change rather than also a node re-ordering. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Olof Johansson <olof@lixom.net>
2012-05-11 23:03:26 +00:00
usb@c5004000 {
ARM: dt: tegra: invert status=disable vs status=okay In tegra*.dtsi, set status="disable" for all HW modules that the board design may choose not to use. Update all boards to specifically enable any of those modules that are useful by setting status="okay". This makes board files say which features they do use, rather than which they don't, which feels more logical. It also makes the .dts files slightly smaller, at least for existing content. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Olof Johansson <olof@lixom.net>
2012-05-11 23:32:56 +00:00
status = "okay";
ARM: dt: tegra: sort nodes based on bus order Sort the nodes according to the following rules: * First, any overrides for properties or nodes created by included files, in the order they appeared in the include file. * Second, any nodes with a reg property, in numerical order. * Third, any nodes without a reg property, in alphabetical order of node name. The second sorting rule at least will probably help if/when we need to explicitly insert nodes for the various busses in Tegra; that will just be an indentation change rather than also a node re-ordering. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Olof Johansson <olof@lixom.net>
2012-05-11 23:03:26 +00:00
nvidia,phy-reset-gpio = <&gpio 168 0>; /* gpio PV0 */
arm/dt: tegra: add dts file for paz00 This adds a dts file for paz00. As a side effect, this also enables the embedded controller which controls the keyboard, touchpad, power, leds, and some other functions. Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Marc Dietrich <marvin24@gmx.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2011-11-01 10:37:05 +00:00
};
ARM: dt: tegra: invert status=disable vs status=okay In tegra*.dtsi, set status="disable" for all HW modules that the board design may choose not to use. Update all boards to specifically enable any of those modules that are useful by setting status="okay". This makes board files say which features they do use, rather than which they don't, which feels more logical. It also makes the .dts files slightly smaller, at least for existing content. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Olof Johansson <olof@lixom.net>
2012-05-11 23:32:56 +00:00
usb@c5008000 {
status = "okay";
};
arm/dt: tegra: add dts file for paz00 This adds a dts file for paz00. As a side effect, this also enables the embedded controller which controls the keyboard, touchpad, power, leds, and some other functions. Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Marc Dietrich <marvin24@gmx.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2011-11-01 10:37:05 +00:00
sdhci@c8000000 {
ARM: dt: tegra: invert status=disable vs status=okay In tegra*.dtsi, set status="disable" for all HW modules that the board design may choose not to use. Update all boards to specifically enable any of those modules that are useful by setting status="okay". This makes board files say which features they do use, rather than which they don't, which feels more logical. It also makes the .dts files slightly smaller, at least for existing content. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Olof Johansson <olof@lixom.net>
2012-05-11 23:32:56 +00:00
status = "okay";
arm/dt: tegra: add dts file for paz00 This adds a dts file for paz00. As a side effect, this also enables the embedded controller which controls the keyboard, touchpad, power, leds, and some other functions. Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Marc Dietrich <marvin24@gmx.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2011-11-01 10:37:05 +00:00
cd-gpios = <&gpio 173 0>; /* gpio PV5 */
wp-gpios = <&gpio 57 0>; /* gpio PH1 */
ARM: tegra: paz00: fix wrong SD1 power gpio The power gpio for the external memory card was specified wrongly. Replace it with the correct value (tested with warmboot with fastboot). Signed-off-by: Marc Dietrich <marvin24@gmx.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2012-01-28 19:03:04 +00:00
power-gpios = <&gpio 169 0>; /* gpio PV1 */
mmc: dt: Consolidate DT bindings This patch unifies the current DT MMC bindings documentation and code, adds generic MMC DT bindings documentation, and updates .dts files for consistency. [cjb: typo fixes, addition of max-frequency property] Signed-off-by: Chris Ball <cjb@laptop.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-05-13 04:14:24 +00:00
bus-width = <4>;
arm/dt: tegra: add dts file for paz00 This adds a dts file for paz00. As a side effect, this also enables the embedded controller which controls the keyboard, touchpad, power, leds, and some other functions. Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Marc Dietrich <marvin24@gmx.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2011-11-01 10:37:05 +00:00
};
sdhci@c8000600 {
ARM: dt: tegra: invert status=disable vs status=okay In tegra*.dtsi, set status="disable" for all HW modules that the board design may choose not to use. Update all boards to specifically enable any of those modules that are useful by setting status="okay". This makes board files say which features they do use, rather than which they don't, which feels more logical. It also makes the .dts files slightly smaller, at least for existing content. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Olof Johansson <olof@lixom.net>
2012-05-11 23:32:56 +00:00
status = "okay";
mmc: dt: Consolidate DT bindings This patch unifies the current DT MMC bindings documentation and code, adds generic MMC DT bindings documentation, and updates .dts files for consistency. [cjb: typo fixes, addition of max-frequency property] Signed-off-by: Chris Ball <cjb@laptop.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-05-13 04:14:24 +00:00
bus-width = <8>;
arm/dt: tegra: add dts file for paz00 This adds a dts file for paz00. As a side effect, this also enables the embedded controller which controls the keyboard, touchpad, power, leds, and some other functions. Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Marc Dietrich <marvin24@gmx.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2011-11-01 10:37:05 +00:00
};
ARM: dt: tegra: add the power gpio key to paz00 device tree This adds the wakeup gpio which is connected to the embedded controller to the device tree of paz00. Signed-off-by: Marc Dietrich <marvin24@gmx.de> Signed-off-by: Olof Johansson <olof@lixom.net>
2012-01-28 19:03:07 +00:00
gpio-keys {
compatible = "gpio-keys";
power {
label = "Power";
gpios = <&gpio 79 1>; /* gpio PJ7, active low */
linux,code = <116>; /* KEY_POWER */
gpio-key,wakeup;
};
};
ARM: dt: tegra: add the wifi led to paz00 device tree This adds the wifi led bound to the rfkill0 event to the device tree of paz00. Signed-off-by: Marc Dietrich <marvin24@gmx.de> Signed-off-by: Olof Johansson <olof@lixom.net>
2012-01-28 19:03:08 +00:00
gpio-leds {
compatible = "gpio-leds";
wifi {
label = "wifi-led";
ARM: dt: tegra: gpio comment cleanup Ensure that all Tegraa GPIO specifiers contain a comment indicating which GPIO name the number refers to. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Olof Johansson <olof@lixom.net>
2012-05-11 22:21:10 +00:00
gpios = <&gpio 24 0>; /* gpio PD0 */
ARM: dt: tegra: add the wifi led to paz00 device tree This adds the wifi led bound to the rfkill0 event to the device tree of paz00. Signed-off-by: Marc Dietrich <marvin24@gmx.de> Signed-off-by: Olof Johansson <olof@lixom.net>
2012-01-28 19:03:08 +00:00
linux,default-trigger = "rfkill0";
};
};
ARM: tegra: add USB ULPI PHY reset GPIO to device tree ULPI PHYs have a reset signal, and different boards use a different GPIO for this task. Add a property to device tree to represent this. I'm not sure if adding this property to the EHCI controller node is entirely correct; perhaps eventually we should have explicit separate nodes for the various PHYs. However, we don't have that right now, so this binding seems like a reasonable choice. Cc: <devicetree-discuss@lists.ozlabs.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: <linux-usb@vger.kernel.org> Signed-off-by: Stephen Warren <swarren@nvidia.com>
2012-04-12 21:46:49 +00:00
ARM: dt: tegra: paz00: add regulators The Toshiba AC100/PAZ00 uses a TPS6586x regulator. Instantiate this. Three data sources were used for the data encoded here: * The HW defaults, as extracted from real HW. * The schematic, which specifies a voltage for each rail in the signal names. * The AC100 kernel used by the Ubuntu port: repo git://gitorious.org/~marvin24/ac100/marvin24s-kernel.git branch chromeos-ac100-3.0 file arch/arm/mach-tegra/board-paz00-power.c For many rails, the constraints in that tree specified differing min and max voltages. In all cases, the min value was ignored, since there's no need currently to vary any of the voltages at run-time. DVFS might change this in the future. In most cases these sources all matched. Differences are: sm0: HW defaults and schematic match at 1.2v. marvin24's kernel had a max of 1.3v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. sm1: HW defaults and schematic match at 1.0v. marvin24's kernel had a max of 1.125v, but this higher voltage was only applied to HW by DVFS code, which isn't currently supported in mainline. ldo3: The HW default is on. marvin24's kernel didn't specify always-on, but since the board wasn't marked as having fully constrained regulators, the rail was not turned off, so the difference had no effect. The rail is needed for USB. ldo6: The HW default is 2.85v. The schematics indicate 2.85v. However, since this regulator is used for the same purpose as on other boards that require 1.8v, this is set to 1.8v. Note that this regulator feeds the CRT VDAC on Tegra, and so in practice is unlikely to be used, even though it is actaully hooked up in HW. Portions based on work by Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Tested-by: Marc Dietrich <marvin24@gmx.de> # v2 Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
2012-06-21 20:24:57 +00:00
regulators {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <0>;
p5valw_reg: regulator@0 {
compatible = "regulator-fixed";
reg = <0>;
regulator-name = "+5valw";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-always-on;
};
};
ARM: dt: tegra: sort nodes based on bus order Sort the nodes according to the following rules: * First, any overrides for properties or nodes created by included files, in the order they appeared in the include file. * Second, any nodes with a reg property, in numerical order. * Third, any nodes without a reg property, in alphabetical order of node name. The second sorting rule at least will probably help if/when we need to explicitly insert nodes for the various busses in Tegra; that will just be an indentation change rather than also a node re-ordering. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Olof Johansson <olof@lixom.net>
2012-05-11 23:03:26 +00:00
sound {
compatible = "nvidia,tegra-audio-alc5632-paz00",
"nvidia,tegra-audio-alc5632";
nvidia,model = "Compal PAZ00";
nvidia,audio-routing =
"Int Spk", "SPKOUT",
"Int Spk", "SPKOUTN",
"Headset Mic", "MICBIAS1",
"MIC1", "Headset Mic",
"Headset Stereophone", "HPR",
"Headset Stereophone", "HPL",
"DMICDAT", "Digital Mic";
nvidia,audio-codec = <&alc5632>;
nvidia,i2s-controller = <&tegra_i2s1>;
nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
ARM: tegra: add USB ULPI PHY reset GPIO to device tree ULPI PHYs have a reset signal, and different boards use a different GPIO for this task. Add a property to device tree to represent this. I'm not sure if adding this property to the EHCI controller node is entirely correct; perhaps eventually we should have explicit separate nodes for the various PHYs. However, we don't have that right now, so this binding seems like a reasonable choice. Cc: <devicetree-discuss@lists.ozlabs.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: <linux-usb@vger.kernel.org> Signed-off-by: Stephen Warren <swarren@nvidia.com>
2012-04-12 21:46:49 +00:00
};
arm/dt: tegra: add dts file for paz00 This adds a dts file for paz00. As a side effect, this also enables the embedded controller which controls the keyboard, touchpad, power, leds, and some other functions. Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Marc Dietrich <marvin24@gmx.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2011-11-01 10:37:05 +00:00
};