dect
/
linux-2.6
Archived
13
0
Fork 0
Code Releases Activity
This repository has been archived on 2022-02-17. You can view files and clone it, but cannot push or open issues or pull requests.
linux-2.6/arch/s390/kvm/interrupt.c

612 lines
16 KiB
C
Raw Normal View History

KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
/*
* interrupt.c - handling kvm guest interrupts
*
* Copyright IBM Corp. 2008
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License (version 2 only)
* as published by the Free Software Foundation.
*
* Author(s): Carsten Otte <cotte@de.ibm.com>
*/
KVM: s390: use hrtimer for clock wakeup from idle - v2 This patch reworks the s390 clock comparator wakeup to hrtimer. The clock comparator is a per-cpu value that is compared against the TOD clock. If ckc <= TOD an external interrupt 1004 is triggered. Since the clock comparator and the TOD clock have a much higher resolution than jiffies we should use hrtimers to trigger the wakeup. This speeds up guest nanosleep for small values. Since hrtimers callbacks run in hard-irq context, I added a tasklet to do the actual work with enabled interrupts. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Ehrhardt <ehrhardt@de.ibm.com> Signed-off-by: Avi Kivity <avi@redhat.com>
2009-05-12 15:21:49 +00:00
#include <linux/interrupt.h>
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
#include <linux/kvm_host.h>
[S390] Cleanup struct _lowcore usage and defines. Use asm offsets to make sure the offset defines to struct _lowcore and its layout don't get out of sync. Also add a BUILD_BUG_ON() which checks that the size of the structure is sane. And while being at it change those sites which use odd casts to access the current lowcore. These should use S390_lowcore instead. Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2010-02-26 21:37:43 +00:00
#include <linux/hrtimer.h>
KVM: s390: Fix program check on interrupt delivery handling The current interrupt handling on s390 misbehaves on an error case. On s390 each cpu has the prefix area (lowcore) for interrupt delivery. This memory must always be available. If we fail to access the prefix area for a guest on interrupt delivery the configuration is completely unusable. There is no point in sending another program interrupt to an inaccessible lowcore. Furthermore, we should not bug the host kernel, because this can be triggered by userspace. I think the guest kernel itself can not trigger the problem, as SET PREFIX and SIGNAL PROCESSOR SET PREFIX both check that the memory is available and sane. As this is a userspace bug (e.g. setting the wrong guest offset, unmapping guest memory) we should kill the userspace process instead of BUGing the host kernel. In the long term we probably should notify the userspace process about this problem. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-25 13:51:54 +00:00
#include <linux/signal.h>
include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: Tejun Heo <tj@kernel.org> Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-24 08:04:11 +00:00
#include <linux/slab.h>
[S390] Cleanup struct _lowcore usage and defines. Use asm offsets to make sure the offset defines to struct _lowcore and its layout don't get out of sync. Also add a BUILD_BUG_ON() which checks that the size of the structure is sane. And while being at it change those sites which use odd casts to access the current lowcore. These should use S390_lowcore instead. Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2010-02-26 21:37:43 +00:00
#include <asm/asm-offsets.h>
#include <asm/uaccess.h>
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
#include "kvm-s390.h"
#include "gaccess.h"
static int psw_extint_disabled(struct kvm_vcpu *vcpu)
{
return !(vcpu->arch.sie_block->gpsw.mask & PSW_MASK_EXT);
}
static int psw_interrupts_disabled(struct kvm_vcpu *vcpu)
{
if ((vcpu->arch.sie_block->gpsw.mask & PSW_MASK_PER) ||
(vcpu->arch.sie_block->gpsw.mask & PSW_MASK_IO) ||
(vcpu->arch.sie_block->gpsw.mask & PSW_MASK_EXT))
return 0;
return 1;
}
static int __interrupt_is_deliverable(struct kvm_vcpu *vcpu,
KVM: s390: rename private structures While doing some tests with our lcrash implementation I have seen a naming conflict with prefix_info in kvm_host.h vs. addrconf.h To avoid future conflicts lets rename private definitions in asm/kvm_host.h by adding the kvm_s390 prefix. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-06-27 13:05:40 +00:00
struct kvm_s390_interrupt_info *inti)
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
{
switch (inti->type) {
case KVM_S390_INT_EMERGENCY:
if (psw_extint_disabled(vcpu))
return 0;
if (vcpu->arch.sie_block->gcr[0] & 0x4000ul)
return 1;
return 0;
case KVM_S390_INT_SERVICE:
if (psw_extint_disabled(vcpu))
return 0;
if (vcpu->arch.sie_block->gcr[0] & 0x200ul)
return 1;
return 0;
case KVM_S390_INT_VIRTIO:
if (psw_extint_disabled(vcpu))
return 0;
if (vcpu->arch.sie_block->gcr[0] & 0x200ul)
return 1;
return 0;
case KVM_S390_PROGRAM_INT:
case KVM_S390_SIGP_STOP:
case KVM_S390_SIGP_SET_PREFIX:
case KVM_S390_RESTART:
return 1;
default:
BUG();
}
return 0;
}
static void __set_cpu_idle(struct kvm_vcpu *vcpu)
{
BUG_ON(vcpu->vcpu_id > KVM_MAX_VCPUS - 1);
atomic_set_mask(CPUSTAT_WAIT, &vcpu->arch.sie_block->cpuflags);
set_bit(vcpu->vcpu_id, vcpu->arch.local_int.float_int->idle_mask);
}
static void __unset_cpu_idle(struct kvm_vcpu *vcpu)
{
BUG_ON(vcpu->vcpu_id > KVM_MAX_VCPUS - 1);
atomic_clear_mask(CPUSTAT_WAIT, &vcpu->arch.sie_block->cpuflags);
clear_bit(vcpu->vcpu_id, vcpu->arch.local_int.float_int->idle_mask);
}
static void __reset_intercept_indicators(struct kvm_vcpu *vcpu)
{
atomic_clear_mask(CPUSTAT_ECALL_PEND |
CPUSTAT_IO_INT | CPUSTAT_EXT_INT | CPUSTAT_STOP_INT,
&vcpu->arch.sie_block->cpuflags);
vcpu->arch.sie_block->lctl = 0x0000;
}
static void __set_cpuflag(struct kvm_vcpu *vcpu, u32 flag)
{
atomic_set_mask(flag, &vcpu->arch.sie_block->cpuflags);
}
static void __set_intercept_indicator(struct kvm_vcpu *vcpu,
KVM: s390: rename private structures While doing some tests with our lcrash implementation I have seen a naming conflict with prefix_info in kvm_host.h vs. addrconf.h To avoid future conflicts lets rename private definitions in asm/kvm_host.h by adding the kvm_s390 prefix. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-06-27 13:05:40 +00:00
struct kvm_s390_interrupt_info *inti)
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
{
switch (inti->type) {
case KVM_S390_INT_EMERGENCY:
case KVM_S390_INT_SERVICE:
case KVM_S390_INT_VIRTIO:
if (psw_extint_disabled(vcpu))
__set_cpuflag(vcpu, CPUSTAT_EXT_INT);
else
vcpu->arch.sie_block->lctl |= LCTL_CR0;
break;
case KVM_S390_SIGP_STOP:
__set_cpuflag(vcpu, CPUSTAT_STOP_INT);
break;
default:
BUG();
}
}
static void __do_deliver_interrupt(struct kvm_vcpu *vcpu,
KVM: s390: rename private structures While doing some tests with our lcrash implementation I have seen a naming conflict with prefix_info in kvm_host.h vs. addrconf.h To avoid future conflicts lets rename private definitions in asm/kvm_host.h by adding the kvm_s390 prefix. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-06-27 13:05:40 +00:00
struct kvm_s390_interrupt_info *inti)
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
{
const unsigned short table[] = { 2, 4, 4, 6 };
int rc, exception = 0;
switch (inti->type) {
case KVM_S390_INT_EMERGENCY:
VCPU_EVENT(vcpu, 4, "%s", "interrupt: sigp emerg");
vcpu->stat.deliver_emergency_signal++;
rc = put_guest_u16(vcpu, __LC_EXT_INT_CODE, 0x1201);
if (rc == -EFAULT)
exception = 1;
[S390] kvm: make sigp emerg smp capable SIGP emerg needs to pass the source vpu adress into __LC_CPU_ADDRESS of the target guest. Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2011-07-24 08:48:31 +00:00
rc = put_guest_u16(vcpu, __LC_CPU_ADDRESS, inti->emerg.code);
if (rc == -EFAULT)
exception = 1;
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
rc = copy_to_guest(vcpu, __LC_EXT_OLD_PSW,
&vcpu->arch.sie_block->gpsw, sizeof(psw_t));
if (rc == -EFAULT)
exception = 1;
rc = copy_from_guest(vcpu, &vcpu->arch.sie_block->gpsw,
__LC_EXT_NEW_PSW, sizeof(psw_t));
if (rc == -EFAULT)
exception = 1;
break;
case KVM_S390_INT_SERVICE:
VCPU_EVENT(vcpu, 4, "interrupt: sclp parm:%x",
inti->ext.ext_params);
vcpu->stat.deliver_service_signal++;
rc = put_guest_u16(vcpu, __LC_EXT_INT_CODE, 0x2401);
if (rc == -EFAULT)
exception = 1;
rc = copy_to_guest(vcpu, __LC_EXT_OLD_PSW,
&vcpu->arch.sie_block->gpsw, sizeof(psw_t));
if (rc == -EFAULT)
exception = 1;
rc = copy_from_guest(vcpu, &vcpu->arch.sie_block->gpsw,
__LC_EXT_NEW_PSW, sizeof(psw_t));
if (rc == -EFAULT)
exception = 1;
rc = put_guest_u32(vcpu, __LC_EXT_PARAMS, inti->ext.ext_params);
if (rc == -EFAULT)
exception = 1;
break;
case KVM_S390_INT_VIRTIO:
[S390] Use unsigned long long for u64 on 64bit. As requested by Andrew. Same as what sparc did. Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2009-01-09 11:14:56 +00:00
VCPU_EVENT(vcpu, 4, "interrupt: virtio parm:%x,parm64:%llx",
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
inti->ext.ext_params, inti->ext.ext_params2);
vcpu->stat.deliver_virtio_interrupt++;
rc = put_guest_u16(vcpu, __LC_EXT_INT_CODE, 0x2603);
if (rc == -EFAULT)
exception = 1;
rc = put_guest_u16(vcpu, __LC_CPU_ADDRESS, 0x0d00);
if (rc == -EFAULT)
exception = 1;
rc = copy_to_guest(vcpu, __LC_EXT_OLD_PSW,
&vcpu->arch.sie_block->gpsw, sizeof(psw_t));
if (rc == -EFAULT)
exception = 1;
rc = copy_from_guest(vcpu, &vcpu->arch.sie_block->gpsw,
__LC_EXT_NEW_PSW, sizeof(psw_t));
if (rc == -EFAULT)
exception = 1;
rc = put_guest_u32(vcpu, __LC_EXT_PARAMS, inti->ext.ext_params);
if (rc == -EFAULT)
exception = 1;
[S390] Cleanup struct _lowcore usage and defines. Use asm offsets to make sure the offset defines to struct _lowcore and its layout don't get out of sync. Also add a BUILD_BUG_ON() which checks that the size of the structure is sane. And while being at it change those sites which use odd casts to access the current lowcore. These should use S390_lowcore instead. Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2010-02-26 21:37:43 +00:00
rc = put_guest_u64(vcpu, __LC_EXT_PARAMS2,
inti->ext.ext_params2);
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
if (rc == -EFAULT)
exception = 1;
break;
case KVM_S390_SIGP_STOP:
VCPU_EVENT(vcpu, 4, "%s", "interrupt: cpu stop");
vcpu->stat.deliver_stop_signal++;
__set_intercept_indicator(vcpu, inti);
break;
case KVM_S390_SIGP_SET_PREFIX:
VCPU_EVENT(vcpu, 4, "interrupt: set prefix to %x",
inti->prefix.address);
vcpu->stat.deliver_prefix_signal++;
vcpu->arch.sie_block->prefix = inti->prefix.address;
vcpu->arch.sie_block->ihcpu = 0xffff;
break;
case KVM_S390_RESTART:
VCPU_EVENT(vcpu, 4, "%s", "interrupt: cpu restart");
vcpu->stat.deliver_restart_signal++;
rc = copy_to_guest(vcpu, offsetof(struct _lowcore,
restart_old_psw), &vcpu->arch.sie_block->gpsw, sizeof(psw_t));
if (rc == -EFAULT)
exception = 1;
rc = copy_from_guest(vcpu, &vcpu->arch.sie_block->gpsw,
offsetof(struct _lowcore, restart_psw), sizeof(psw_t));
if (rc == -EFAULT)
exception = 1;
break;
case KVM_S390_PROGRAM_INT:
VCPU_EVENT(vcpu, 4, "interrupt: pgm check code:%x, ilc:%x",
inti->pgm.code,
table[vcpu->arch.sie_block->ipa >> 14]);
vcpu->stat.deliver_program_int++;
rc = put_guest_u16(vcpu, __LC_PGM_INT_CODE, inti->pgm.code);
if (rc == -EFAULT)
exception = 1;
rc = put_guest_u16(vcpu, __LC_PGM_ILC,
table[vcpu->arch.sie_block->ipa >> 14]);
if (rc == -EFAULT)
exception = 1;
rc = copy_to_guest(vcpu, __LC_PGM_OLD_PSW,
&vcpu->arch.sie_block->gpsw, sizeof(psw_t));
if (rc == -EFAULT)
exception = 1;
rc = copy_from_guest(vcpu, &vcpu->arch.sie_block->gpsw,
__LC_PGM_NEW_PSW, sizeof(psw_t));
if (rc == -EFAULT)
exception = 1;
break;
default:
BUG();
}
if (exception) {
KVM: s390: Fix program check on interrupt delivery handling The current interrupt handling on s390 misbehaves on an error case. On s390 each cpu has the prefix area (lowcore) for interrupt delivery. This memory must always be available. If we fail to access the prefix area for a guest on interrupt delivery the configuration is completely unusable. There is no point in sending another program interrupt to an inaccessible lowcore. Furthermore, we should not bug the host kernel, because this can be triggered by userspace. I think the guest kernel itself can not trigger the problem, as SET PREFIX and SIGNAL PROCESSOR SET PREFIX both check that the memory is available and sane. As this is a userspace bug (e.g. setting the wrong guest offset, unmapping guest memory) we should kill the userspace process instead of BUGing the host kernel. In the long term we probably should notify the userspace process about this problem. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-25 13:51:54 +00:00
printk("kvm: The guest lowcore is not mapped during interrupt "
"delivery, killing userspace\n");
do_exit(SIGKILL);
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
}
}
static int __try_deliver_ckc_interrupt(struct kvm_vcpu *vcpu)
{
int rc, exception = 0;
if (psw_extint_disabled(vcpu))
return 0;
if (!(vcpu->arch.sie_block->gcr[0] & 0x800ul))
return 0;
rc = put_guest_u16(vcpu, __LC_EXT_INT_CODE, 0x1004);
if (rc == -EFAULT)
exception = 1;
rc = copy_to_guest(vcpu, __LC_EXT_OLD_PSW,
&vcpu->arch.sie_block->gpsw, sizeof(psw_t));
if (rc == -EFAULT)
exception = 1;
rc = copy_from_guest(vcpu, &vcpu->arch.sie_block->gpsw,
__LC_EXT_NEW_PSW, sizeof(psw_t));
if (rc == -EFAULT)
exception = 1;
if (exception) {
KVM: s390: Fix program check on interrupt delivery handling The current interrupt handling on s390 misbehaves on an error case. On s390 each cpu has the prefix area (lowcore) for interrupt delivery. This memory must always be available. If we fail to access the prefix area for a guest on interrupt delivery the configuration is completely unusable. There is no point in sending another program interrupt to an inaccessible lowcore. Furthermore, we should not bug the host kernel, because this can be triggered by userspace. I think the guest kernel itself can not trigger the problem, as SET PREFIX and SIGNAL PROCESSOR SET PREFIX both check that the memory is available and sane. As this is a userspace bug (e.g. setting the wrong guest offset, unmapping guest memory) we should kill the userspace process instead of BUGing the host kernel. In the long term we probably should notify the userspace process about this problem. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-07-25 13:51:54 +00:00
printk("kvm: The guest lowcore is not mapped during interrupt "
"delivery, killing userspace\n");
do_exit(SIGKILL);
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
}
return 1;
}
KVM: Reduce runnability interface with arch support code Remove kvm_cpu_has_interrupt() and kvm_arch_interrupt_allowed() from interface between general code and arch code. kvm_arch_vcpu_runnable() checks for interrupts instead. Signed-off-by: Gleb Natapov <gleb@redhat.com> Signed-off-by: Avi Kivity <avi@redhat.com>
2009-07-09 12:33:52 +00:00
static int kvm_cpu_has_interrupt(struct kvm_vcpu *vcpu)
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
{
KVM: s390: rename private structures While doing some tests with our lcrash implementation I have seen a naming conflict with prefix_info in kvm_host.h vs. addrconf.h To avoid future conflicts lets rename private definitions in asm/kvm_host.h by adding the kvm_s390 prefix. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-06-27 13:05:40 +00:00
struct kvm_s390_local_interrupt *li = &vcpu->arch.local_int;
struct kvm_s390_float_interrupt *fi = vcpu->arch.local_int.float_int;
struct kvm_s390_interrupt_info *inti;
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
int rc = 0;
if (atomic_read(&li->active)) {
spin_lock_bh(&li->lock);
list_for_each_entry(inti, &li->list, list)
if (__interrupt_is_deliverable(vcpu, inti)) {
rc = 1;
break;
}
spin_unlock_bh(&li->lock);
}
if ((!rc) && atomic_read(&fi->active)) {
KVM: s390: optimize float int lock: spin_lock_bh --> spin_lock The floating interrupt lock is only taken in process context. We can replace all spin_lock_bh with standard spin_lock calls. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Christian Ehrhardt <ehrhardt@de.ibm.com> Signed-off-by: Avi Kivity <avi@redhat.com>
2009-05-12 15:21:50 +00:00
spin_lock(&fi->lock);
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
list_for_each_entry(inti, &fi->list, list)
if (__interrupt_is_deliverable(vcpu, inti)) {
rc = 1;
break;
}
KVM: s390: optimize float int lock: spin_lock_bh --> spin_lock The floating interrupt lock is only taken in process context. We can replace all spin_lock_bh with standard spin_lock calls. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Christian Ehrhardt <ehrhardt@de.ibm.com> Signed-off-by: Avi Kivity <avi@redhat.com>
2009-05-12 15:21:50 +00:00
spin_unlock(&fi->lock);
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
}
if ((!rc) && (vcpu->arch.sie_block->ckc <
get_clock() + vcpu->arch.sie_block->epoch)) {
if ((!psw_extint_disabled(vcpu)) &&
(vcpu->arch.sie_block->gcr[0] & 0x800ul))
rc = 1;
}
return rc;
}
KVM: hlt emulation should take in-kernel APIC/PIT timers into account Timers that fire between guest hlt and vcpu_block's add_wait_queue() are ignored, possibly resulting in hangs. Also make sure that atomic_inc and waitqueue_active tests happen in the specified order, otherwise the following race is open: CPU0 CPU1 if (waitqueue_active(wq)) add_wait_queue() if (!atomic_read(pit_timer->pending)) schedule() atomic_inc(pit_timer->pending) Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-04-11 17:53:26 +00:00
int kvm_cpu_has_pending_timer(struct kvm_vcpu *vcpu)
{
return 0;
}
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
int kvm_s390_handle_wait(struct kvm_vcpu *vcpu)
{
u64 now, sltime;
DECLARE_WAITQUEUE(wait, current);
vcpu->stat.exit_wait_state++;
if (kvm_cpu_has_interrupt(vcpu))
return 0;
KVM: s390: Fix race condition in kvm_s390_handle_wait The call to add_timer was issued before local_int.lock was taken and before timer_due was set to 0. If the timer expires before the lock is being taken, the timer function will set timer_due to 1 and exit before the vcpu falls asleep. Depending on other external events, the vcpu might sleep forever. This fix pulls setting timer_due to the beginning of the function before add_timer, which ensures correct behavior. Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-05-21 11:37:44 +00:00
__set_cpu_idle(vcpu);
spin_lock_bh(&vcpu->arch.local_int.lock);
vcpu->arch.local_int.timer_due = 0;
spin_unlock_bh(&vcpu->arch.local_int.lock);
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
if (psw_interrupts_disabled(vcpu)) {
VCPU_EVENT(vcpu, 3, "%s", "disabled wait");
__unset_cpu_idle(vcpu);
[S390] Replace ENOTSUPP usage with EOPNOTSUPP ENOTSUPP is not supposed to leak to userspace so lets just use EOPNOTSUPP everywhere. Doesn't fix a bug, but makes future reviews easier. Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2010-02-26 21:37:41 +00:00
return -EOPNOTSUPP; /* disabled wait */
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
}
if (psw_extint_disabled(vcpu) ||
(!(vcpu->arch.sie_block->gcr[0] & 0x800ul))) {
VCPU_EVENT(vcpu, 3, "%s", "enabled wait w/o timer");
goto no_timer;
}
now = get_clock() + vcpu->arch.sie_block->epoch;
if (vcpu->arch.sie_block->ckc < now) {
__unset_cpu_idle(vcpu);
return 0;
}
KVM: s390: use hrtimer for clock wakeup from idle - v2 This patch reworks the s390 clock comparator wakeup to hrtimer. The clock comparator is a per-cpu value that is compared against the TOD clock. If ckc <= TOD an external interrupt 1004 is triggered. Since the clock comparator and the TOD clock have a much higher resolution than jiffies we should use hrtimers to trigger the wakeup. This speeds up guest nanosleep for small values. Since hrtimers callbacks run in hard-irq context, I added a tasklet to do the actual work with enabled interrupts. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Ehrhardt <ehrhardt@de.ibm.com> Signed-off-by: Avi Kivity <avi@redhat.com>
2009-05-12 15:21:49 +00:00
sltime = ((vcpu->arch.sie_block->ckc - now)*125)>>9;
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
KVM: s390: use hrtimer for clock wakeup from idle - v2 This patch reworks the s390 clock comparator wakeup to hrtimer. The clock comparator is a per-cpu value that is compared against the TOD clock. If ckc <= TOD an external interrupt 1004 is triggered. Since the clock comparator and the TOD clock have a much higher resolution than jiffies we should use hrtimers to trigger the wakeup. This speeds up guest nanosleep for small values. Since hrtimers callbacks run in hard-irq context, I added a tasklet to do the actual work with enabled interrupts. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Ehrhardt <ehrhardt@de.ibm.com> Signed-off-by: Avi Kivity <avi@redhat.com>
2009-05-12 15:21:49 +00:00
hrtimer_start(&vcpu->arch.ckc_timer, ktime_set (0, sltime) , HRTIMER_MODE_REL);
VCPU_EVENT(vcpu, 5, "enabled wait via clock comparator: %llx ns", sltime);
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
no_timer:
KVM: s390: optimize float int lock: spin_lock_bh --> spin_lock The floating interrupt lock is only taken in process context. We can replace all spin_lock_bh with standard spin_lock calls. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Christian Ehrhardt <ehrhardt@de.ibm.com> Signed-off-by: Avi Kivity <avi@redhat.com>
2009-05-12 15:21:50 +00:00
spin_lock(&vcpu->arch.local_int.float_int->lock);
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
spin_lock_bh(&vcpu->arch.local_int.lock);
add_wait_queue(&vcpu->arch.local_int.wq, &wait);
while (list_empty(&vcpu->arch.local_int.list) &&
list_empty(&vcpu->arch.local_int.float_int->list) &&
(!vcpu->arch.local_int.timer_due) &&
!signal_pending(current)) {
set_current_state(TASK_INTERRUPTIBLE);
spin_unlock_bh(&vcpu->arch.local_int.lock);
KVM: s390: optimize float int lock: spin_lock_bh --> spin_lock The floating interrupt lock is only taken in process context. We can replace all spin_lock_bh with standard spin_lock calls. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Christian Ehrhardt <ehrhardt@de.ibm.com> Signed-off-by: Avi Kivity <avi@redhat.com>
2009-05-12 15:21:50 +00:00
spin_unlock(&vcpu->arch.local_int.float_int->lock);
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
vcpu_put(vcpu);
schedule();
vcpu_load(vcpu);
KVM: s390: optimize float int lock: spin_lock_bh --> spin_lock The floating interrupt lock is only taken in process context. We can replace all spin_lock_bh with standard spin_lock calls. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Christian Ehrhardt <ehrhardt@de.ibm.com> Signed-off-by: Avi Kivity <avi@redhat.com>
2009-05-12 15:21:50 +00:00
spin_lock(&vcpu->arch.local_int.float_int->lock);
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
spin_lock_bh(&vcpu->arch.local_int.lock);
}
__unset_cpu_idle(vcpu);
__set_current_state(TASK_RUNNING);
KVM: s390: fix wait_queue handling There are two waitqueues in kvm for wait handling: vcpu->wq for virt/kvm/kvm_main.c and vpcu->arch.local_int.wq for the s390 specific wait code. the wait handling in kvm_s390_handle_wait was broken by using different wait_queues for add_wait queue and remove_wait_queue. There are two options to fix the problem: o move all the s390 specific code to vcpu->wq and remove vcpu->arch.local_int.wq o move all the s390 specific code to vcpu->arch.local_int.wq This patch chooses the 2nd variant for two reasons: o s390 does not use kvm_vcpu_block but implements its own enabled wait handling. Having a separate wait_queue make it clear, that our wait mechanism is different o the patch is much smaller Report-by: Julia Lawall <julia@diku.dk> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Avi Kivity <avi@redhat.com>
2009-07-16 15:17:37 +00:00
remove_wait_queue(&vcpu->arch.local_int.wq, &wait);
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
spin_unlock_bh(&vcpu->arch.local_int.lock);
KVM: s390: optimize float int lock: spin_lock_bh --> spin_lock The floating interrupt lock is only taken in process context. We can replace all spin_lock_bh with standard spin_lock calls. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Christian Ehrhardt <ehrhardt@de.ibm.com> Signed-off-by: Avi Kivity <avi@redhat.com>
2009-05-12 15:21:50 +00:00
spin_unlock(&vcpu->arch.local_int.float_int->lock);
KVM: s390: use hrtimer for clock wakeup from idle - v2 This patch reworks the s390 clock comparator wakeup to hrtimer. The clock comparator is a per-cpu value that is compared against the TOD clock. If ckc <= TOD an external interrupt 1004 is triggered. Since the clock comparator and the TOD clock have a much higher resolution than jiffies we should use hrtimers to trigger the wakeup. This speeds up guest nanosleep for small values. Since hrtimers callbacks run in hard-irq context, I added a tasklet to do the actual work with enabled interrupts. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Ehrhardt <ehrhardt@de.ibm.com> Signed-off-by: Avi Kivity <avi@redhat.com>
2009-05-12 15:21:49 +00:00
hrtimer_try_to_cancel(&vcpu->arch.ckc_timer);
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
return 0;
}
KVM: s390: use hrtimer for clock wakeup from idle - v2 This patch reworks the s390 clock comparator wakeup to hrtimer. The clock comparator is a per-cpu value that is compared against the TOD clock. If ckc <= TOD an external interrupt 1004 is triggered. Since the clock comparator and the TOD clock have a much higher resolution than jiffies we should use hrtimers to trigger the wakeup. This speeds up guest nanosleep for small values. Since hrtimers callbacks run in hard-irq context, I added a tasklet to do the actual work with enabled interrupts. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Ehrhardt <ehrhardt@de.ibm.com> Signed-off-by: Avi Kivity <avi@redhat.com>
2009-05-12 15:21:49 +00:00
void kvm_s390_tasklet(unsigned long parm)
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
{
KVM: s390: use hrtimer for clock wakeup from idle - v2 This patch reworks the s390 clock comparator wakeup to hrtimer. The clock comparator is a per-cpu value that is compared against the TOD clock. If ckc <= TOD an external interrupt 1004 is triggered. Since the clock comparator and the TOD clock have a much higher resolution than jiffies we should use hrtimers to trigger the wakeup. This speeds up guest nanosleep for small values. Since hrtimers callbacks run in hard-irq context, I added a tasklet to do the actual work with enabled interrupts. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Ehrhardt <ehrhardt@de.ibm.com> Signed-off-by: Avi Kivity <avi@redhat.com>
2009-05-12 15:21:49 +00:00
struct kvm_vcpu *vcpu = (struct kvm_vcpu *) parm;
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
KVM: s390: use hrtimer for clock wakeup from idle - v2 This patch reworks the s390 clock comparator wakeup to hrtimer. The clock comparator is a per-cpu value that is compared against the TOD clock. If ckc <= TOD an external interrupt 1004 is triggered. Since the clock comparator and the TOD clock have a much higher resolution than jiffies we should use hrtimers to trigger the wakeup. This speeds up guest nanosleep for small values. Since hrtimers callbacks run in hard-irq context, I added a tasklet to do the actual work with enabled interrupts. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Ehrhardt <ehrhardt@de.ibm.com> Signed-off-by: Avi Kivity <avi@redhat.com>
2009-05-12 15:21:49 +00:00
spin_lock(&vcpu->arch.local_int.lock);
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
vcpu->arch.local_int.timer_due = 1;
if (waitqueue_active(&vcpu->arch.local_int.wq))
wake_up_interruptible(&vcpu->arch.local_int.wq);
KVM: s390: use hrtimer for clock wakeup from idle - v2 This patch reworks the s390 clock comparator wakeup to hrtimer. The clock comparator is a per-cpu value that is compared against the TOD clock. If ckc <= TOD an external interrupt 1004 is triggered. Since the clock comparator and the TOD clock have a much higher resolution than jiffies we should use hrtimers to trigger the wakeup. This speeds up guest nanosleep for small values. Since hrtimers callbacks run in hard-irq context, I added a tasklet to do the actual work with enabled interrupts. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Ehrhardt <ehrhardt@de.ibm.com> Signed-off-by: Avi Kivity <avi@redhat.com>
2009-05-12 15:21:49 +00:00
spin_unlock(&vcpu->arch.local_int.lock);
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
}
KVM: s390: use hrtimer for clock wakeup from idle - v2 This patch reworks the s390 clock comparator wakeup to hrtimer. The clock comparator is a per-cpu value that is compared against the TOD clock. If ckc <= TOD an external interrupt 1004 is triggered. Since the clock comparator and the TOD clock have a much higher resolution than jiffies we should use hrtimers to trigger the wakeup. This speeds up guest nanosleep for small values. Since hrtimers callbacks run in hard-irq context, I added a tasklet to do the actual work with enabled interrupts. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Ehrhardt <ehrhardt@de.ibm.com> Signed-off-by: Avi Kivity <avi@redhat.com>
2009-05-12 15:21:49 +00:00
/*
* low level hrtimer wake routine. Because this runs in hardirq context
* we schedule a tasklet to do the real work.
*/
enum hrtimer_restart kvm_s390_idle_wakeup(struct hrtimer *timer)
{
struct kvm_vcpu *vcpu;
vcpu = container_of(timer, struct kvm_vcpu, arch.ckc_timer);
tasklet_schedule(&vcpu->arch.tasklet);
return HRTIMER_NORESTART;
}
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
void kvm_s390_deliver_pending_interrupts(struct kvm_vcpu *vcpu)
{
KVM: s390: rename private structures While doing some tests with our lcrash implementation I have seen a naming conflict with prefix_info in kvm_host.h vs. addrconf.h To avoid future conflicts lets rename private definitions in asm/kvm_host.h by adding the kvm_s390 prefix. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-06-27 13:05:40 +00:00
struct kvm_s390_local_interrupt *li = &vcpu->arch.local_int;
struct kvm_s390_float_interrupt *fi = vcpu->arch.local_int.float_int;
struct kvm_s390_interrupt_info *n, *inti = NULL;
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
int deliver;
__reset_intercept_indicators(vcpu);
if (atomic_read(&li->active)) {
do {
deliver = 0;
spin_lock_bh(&li->lock);
list_for_each_entry_safe(inti, n, &li->list, list) {
if (__interrupt_is_deliverable(vcpu, inti)) {
list_del(&inti->list);
deliver = 1;
break;
}
__set_intercept_indicator(vcpu, inti);
}
if (list_empty(&li->list))
atomic_set(&li->active, 0);
spin_unlock_bh(&li->lock);
if (deliver) {
__do_deliver_interrupt(vcpu, inti);
kfree(inti);
}
} while (deliver);
}
if ((vcpu->arch.sie_block->ckc <
get_clock() + vcpu->arch.sie_block->epoch))
__try_deliver_ckc_interrupt(vcpu);
if (atomic_read(&fi->active)) {
do {
deliver = 0;
KVM: s390: optimize float int lock: spin_lock_bh --> spin_lock The floating interrupt lock is only taken in process context. We can replace all spin_lock_bh with standard spin_lock calls. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Christian Ehrhardt <ehrhardt@de.ibm.com> Signed-off-by: Avi Kivity <avi@redhat.com>
2009-05-12 15:21:50 +00:00
spin_lock(&fi->lock);
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
list_for_each_entry_safe(inti, n, &fi->list, list) {
if (__interrupt_is_deliverable(vcpu, inti)) {
list_del(&inti->list);
deliver = 1;
break;
}
__set_intercept_indicator(vcpu, inti);
}
if (list_empty(&fi->list))
atomic_set(&fi->active, 0);
KVM: s390: optimize float int lock: spin_lock_bh --> spin_lock The floating interrupt lock is only taken in process context. We can replace all spin_lock_bh with standard spin_lock calls. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Christian Ehrhardt <ehrhardt@de.ibm.com> Signed-off-by: Avi Kivity <avi@redhat.com>
2009-05-12 15:21:50 +00:00
spin_unlock(&fi->lock);
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
if (deliver) {
__do_deliver_interrupt(vcpu, inti);
kfree(inti);
}
} while (deliver);
}
}
int kvm_s390_inject_program_int(struct kvm_vcpu *vcpu, u16 code)
{
KVM: s390: rename private structures While doing some tests with our lcrash implementation I have seen a naming conflict with prefix_info in kvm_host.h vs. addrconf.h To avoid future conflicts lets rename private definitions in asm/kvm_host.h by adding the kvm_s390 prefix. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-06-27 13:05:40 +00:00
struct kvm_s390_local_interrupt *li = &vcpu->arch.local_int;
struct kvm_s390_interrupt_info *inti;
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
inti = kzalloc(sizeof(*inti), GFP_KERNEL);
if (!inti)
return -ENOMEM;
trivial: remove unnecessary semicolons Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-08-18 18:18:35 +00:00
inti->type = KVM_S390_PROGRAM_INT;
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
inti->pgm.code = code;
VCPU_EVENT(vcpu, 3, "inject: program check %d (from kernel)", code);
spin_lock_bh(&li->lock);
list_add(&inti->list, &li->list);
atomic_set(&li->active, 1);
BUG_ON(waitqueue_active(&li->wq));
spin_unlock_bh(&li->lock);
return 0;
}
int kvm_s390_inject_vm(struct kvm *kvm,
struct kvm_s390_interrupt *s390int)
{
KVM: s390: rename private structures While doing some tests with our lcrash implementation I have seen a naming conflict with prefix_info in kvm_host.h vs. addrconf.h To avoid future conflicts lets rename private definitions in asm/kvm_host.h by adding the kvm_s390 prefix. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-06-27 13:05:40 +00:00
struct kvm_s390_local_interrupt *li;
struct kvm_s390_float_interrupt *fi;
struct kvm_s390_interrupt_info *inti;
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
int sigcpu;
inti = kzalloc(sizeof(*inti), GFP_KERNEL);
if (!inti)
return -ENOMEM;
switch (s390int->type) {
case KVM_S390_INT_VIRTIO:
[S390] Use unsigned long long for u64 on 64bit. As requested by Andrew. Same as what sparc did. Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2009-01-09 11:14:56 +00:00
VM_EVENT(kvm, 5, "inject: virtio parm:%x,parm64:%llx",
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
s390int->parm, s390int->parm64);
inti->type = s390int->type;
inti->ext.ext_params = s390int->parm;
inti->ext.ext_params2 = s390int->parm64;
break;
case KVM_S390_INT_SERVICE:
VM_EVENT(kvm, 5, "inject: sclp parm:%x", s390int->parm);
inti->type = s390int->type;
inti->ext.ext_params = s390int->parm;
break;
case KVM_S390_PROGRAM_INT:
case KVM_S390_SIGP_STOP:
case KVM_S390_INT_EMERGENCY:
default:
kfree(inti);
return -EINVAL;
}
mutex_lock(&kvm->lock);
fi = &kvm->arch.float_int;
KVM: s390: optimize float int lock: spin_lock_bh --> spin_lock The floating interrupt lock is only taken in process context. We can replace all spin_lock_bh with standard spin_lock calls. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Christian Ehrhardt <ehrhardt@de.ibm.com> Signed-off-by: Avi Kivity <avi@redhat.com>
2009-05-12 15:21:50 +00:00
spin_lock(&fi->lock);
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
list_add_tail(&inti->list, &fi->list);
atomic_set(&fi->active, 1);
sigcpu = find_first_bit(fi->idle_mask, KVM_MAX_VCPUS);
if (sigcpu == KVM_MAX_VCPUS) {
do {
sigcpu = fi->next_rr_cpu++;
if (sigcpu == KVM_MAX_VCPUS)
sigcpu = fi->next_rr_cpu = 0;
} while (fi->local_int[sigcpu] == NULL);
}
li = fi->local_int[sigcpu];
spin_lock_bh(&li->lock);
atomic_set_mask(CPUSTAT_EXT_INT, li->cpuflags);
if (waitqueue_active(&li->wq))
wake_up_interruptible(&li->wq);
spin_unlock_bh(&li->lock);
KVM: s390: optimize float int lock: spin_lock_bh --> spin_lock The floating interrupt lock is only taken in process context. We can replace all spin_lock_bh with standard spin_lock calls. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Christian Ehrhardt <ehrhardt@de.ibm.com> Signed-off-by: Avi Kivity <avi@redhat.com>
2009-05-12 15:21:50 +00:00
spin_unlock(&fi->lock);
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
mutex_unlock(&kvm->lock);
return 0;
}
int kvm_s390_inject_vcpu(struct kvm_vcpu *vcpu,
struct kvm_s390_interrupt *s390int)
{
KVM: s390: rename private structures While doing some tests with our lcrash implementation I have seen a naming conflict with prefix_info in kvm_host.h vs. addrconf.h To avoid future conflicts lets rename private definitions in asm/kvm_host.h by adding the kvm_s390 prefix. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-06-27 13:05:40 +00:00
struct kvm_s390_local_interrupt *li;
struct kvm_s390_interrupt_info *inti;
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
inti = kzalloc(sizeof(*inti), GFP_KERNEL);
if (!inti)
return -ENOMEM;
switch (s390int->type) {
case KVM_S390_PROGRAM_INT:
if (s390int->parm & 0xffff0000) {
kfree(inti);
return -EINVAL;
}
inti->type = s390int->type;
inti->pgm.code = s390int->parm;
VCPU_EVENT(vcpu, 3, "inject: program check %d (from user)",
s390int->parm);
break;
KVM: s390: Fix SIGP set prefix ioctl This patch fixes the SET PREFIX interrupt if triggered by userspace. Until now, it was not necessary, but life migration will need it. In addition, it helped me creating SMP support for my kvm_crashme tool (lets kvm execute random guest memory content). Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@redhat.com>
2009-01-22 09:29:08 +00:00
case KVM_S390_SIGP_SET_PREFIX:
inti->prefix.address = s390int->parm;
inti->type = s390int->type;
VCPU_EVENT(vcpu, 3, "inject: set prefix to %x (from user)",
s390int->parm);
break;
KVM: s390: interrupt subsystem, cpu timer, waitpsw This patch contains the s390 interrupt subsystem (similar to in kernel apic) including timer interrupts (similar to in-kernel-pit) and enabled wait (similar to in kernel hlt). In order to achieve that, this patch also introduces intercept handling for instruction intercepts, and it implements load control instructions. This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both the vm file descriptors and the vcpu file descriptors. In case this ioctl is issued against a vm file descriptor, the interrupt is considered floating. Floating interrupts may be delivered to any virtual cpu in the configuration. The following interrupts are supported: SIGP STOP - interprocessor signal that stops a remote cpu SIGP SET PREFIX - interprocessor signal that sets the prefix register of a (stopped) remote cpu INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed and for smp_call_function() in the guest. PROGRAM INT - exception during program execution such as page fault, illegal instruction and friends RESTART - interprocessor signal that starts a stopped cpu INT VIRTIO - floating interrupt for virtio signalisation INT SERVICE - floating interrupt for signalisations from the system service processor struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting an interrupt, also carrys parameter data for interrupts along with the interrupt type. Interrupts on s390 usually have a state that represents the current operation, or identifies which device has caused the interruption on s390. kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a disabled wait (that is, disabled for interrupts), we exit to userspace. In case of an enabled wait we set up a timer that equals the cpu clock comparator value and sleep on a wait queue. [christian: change virtio interrupt to 0x2603] Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
2008-03-25 17:47:26 +00:00
case KVM_S390_SIGP_STOP:
case KVM_S390_RESTART:
case KVM_S390_INT_EMERGENCY:
VCPU_EVENT(vcpu, 3, "inject: type %x", s390int->type);
inti->type = s390int->type;
break;
case KVM_S390_INT_VIRTIO:
case KVM_S390_INT_SERVICE:
default:
kfree(inti);
return -EINVAL;
}
mutex_lock(&vcpu->kvm->lock);
li = &vcpu->arch.local_int;
spin_lock_bh(&li->lock);
if (inti->type == KVM_S390_PROGRAM_INT)
list_add(&inti->list, &li->list);
else
list_add_tail(&inti->list, &li->list);
atomic_set(&li->active, 1);
if (inti->type == KVM_S390_SIGP_STOP)
li->action_bits |= ACTION_STOP_ON_STOP;
atomic_set_mask(CPUSTAT_EXT_INT, li->cpuflags);
if (waitqueue_active(&li->wq))
wake_up_interruptible(&vcpu->arch.local_int.wq);
spin_unlock_bh(&li->lock);
mutex_unlock(&vcpu->kvm->lock);
return 0;
}