62 lines
3.1 KiB
Plaintext
62 lines
3.1 KiB
Plaintext
[general]
|
|
|
|
; General config options, with default values shown.
|
|
; You should use one section per device, with [general] being used
|
|
; for the device.
|
|
|
|
; debug = 0x0 ; misc debug flags, default is 0
|
|
|
|
; Set the device to use for I/O
|
|
; devicenum = 0
|
|
; Set hardware type here
|
|
; hdwtype=0 ; 0=limey, 1=sph
|
|
|
|
; rxboost=0 ; no rx gain boost
|
|
; rxctcssrelax=1 ; reduce talkoff from radios w/o CTCSS Tx HPF
|
|
; rxctcssfreq=100.0 ; rx ctcss freq in floating point. must be in table
|
|
; txctcssfreq=100.0 ; tx ctcss freq, any frequency permitted
|
|
|
|
; carrierfrom=dsp ;no,usb,usbinvert,dsp,vox
|
|
; ctcssfrom=dsp ;no,usb,dsp
|
|
|
|
; rxdemod=flat ; input type from radio: no,speaker,flat
|
|
; txprelim=yes ; output is pre-emphasised and limited
|
|
; txtoctype=no ; no,phase,notone
|
|
|
|
; txmixa=composite ;no,voice,tone,composite,auxvoice
|
|
; txmixb=no ;no,voice,tone,composite,auxvoice
|
|
|
|
; invertptt=0
|
|
|
|
;------------------------------ JITTER BUFFER CONFIGURATION --------------------------
|
|
; jbenable = yes ; Enables the use of a jitterbuffer on the receiving side of an
|
|
; USBRADIO channel. Defaults to "no". An enabled jitterbuffer will
|
|
; be used only if the sending side can create and the receiving
|
|
; side can not accept jitter. The USBRADIO channel can't accept jitter,
|
|
; thus an enabled jitterbuffer on the receive USBRADIO side will always
|
|
; be used if the sending side can create jitter.
|
|
|
|
; jbmaxsize = 200 ; Max length of the jitterbuffer in milliseconds.
|
|
|
|
; jbresyncthreshold = 1000 ; Jump in the frame timestamps over which the jitterbuffer is
|
|
; resynchronized. Useful to improve the quality of the voice, with
|
|
; big jumps in/broken timestamps, usualy sent from exotic devices
|
|
; and programs. Defaults to 1000.
|
|
|
|
; jbimpl = fixed ; Jitterbuffer implementation, used on the receiving side of an USBRADIO
|
|
; channel. Two implementations are currenlty available - "fixed"
|
|
; (with size always equals to jbmax-size) and "adaptive" (with
|
|
; variable size, actually the new jb of IAX2). Defaults to fixed.
|
|
|
|
; jbtargetextra = 40 ; This option only affects the jb when 'jbimpl = adaptive' is set.
|
|
; The option represents the number of milliseconds by which the new
|
|
; jitter buffer will pad its size. the default is 40, so without
|
|
; modification, the new jitter buffer will set its size to the jitter
|
|
; value plus 40 milliseconds. increasing this value may help if your
|
|
; network normally has low jitter, but occasionally has spikes.
|
|
|
|
; jblog = no ; Enables jitterbuffer frame logging. Defaults to "no".
|
|
;-----------------------------------------------------------------------------------
|
|
|
|
|