asterisk/configs/sip.conf.sample

;
; SIP Configuration example for Asterisk
;
; Syntax for specifying a SIP device in extensions.conf is
; SIP/devicename where devicename is defined in a section below.
;
; You may also use 
; SIP/username@domain to call any SIP user on the Internet
; (Don't forget to enable DNS SRV records if you want to use this)
; 
; If you define a SIP proxy as a peer below, you may call
; SIP/proxyhostname/user or SIP/user@proxyhostname 
; where the proxyhostname is defined in a section below 
; 
; Useful CLI commands to check peers/users:
;   sip list peers		Show all SIP peers (including friends)
;   sip list users		Show all SIP users (including friends)
;   sip list registry		Show status of hosts we register with
;
;   sip debug			Show all SIP messages
;
;   sip reload			Reload configuration file
;				Active SIP peers will not be reconfigured
;

[general]
context=default			; Default context for incoming calls
;allowguest=no			; Allow or reject guest calls (default is yes)
;match_auth_username=yes	; if available, match user entry using the
				; 'username' field from the authentication line
				; instead of the From: field.
				
allowoverlap=no			; Disable overlap dialing support. (Default is yes)
;allowtransfer=no		; Disable all transfers (unless enabled in peers or users)
				; Default is enabled
;realm=mydomain.tld		; Realm for digest authentication
				; defaults to "asterisk". If you set a system name in
				; asterisk.conf, it defaults to that system name
				; Realms MUST be globally unique according to RFC 3261
				; Set this to your host name or domain name
bindport=5060			; UDP Port to bind to (SIP standard port is 5060)
bindaddr=0.0.0.0		; IP address to bind to (0.0.0.0 binds to all)
srvlookup=yes			; Enable DNS SRV lookups on outbound calls
				; Note: Asterisk only uses the first host 
				; in SRV records
				; Disabling DNS SRV lookups disables the 
				; ability to place SIP calls based on domain 
				; names to some other SIP users on the Internet
				
;domain=mydomain.tld		; Set default domain for this host
				; If configured, Asterisk will only allow
				; INVITE and REFER to non-local domains
				; Use "sip show domains" to list local domains
;pedantic=yes			; Enable checking of tags in headers, 
				; international character conversions in URIs
				; and multiline formatted headers for strict
				; SIP compatibility (defaults to "no")

; See doc/README.tos for a description of these parameters.
;tos_sip=cs3                    ; Sets TOS for SIP packets.
;tos_audio=ef                   ; Sets TOS for RTP audio packets.
;tos_video=af41                 ; Sets TOS for RTP video packets.

;maxexpiry=3600			; Maximum allowed time of incoming registrations
				; and subscriptions (seconds)
;minexpiry=60			; Minimum length of registrations/subscriptions (default 60)
;defaultexpiry=120		; Default length of incoming/outgoing registration
;t1min=100			; Minimum roundtrip time for messages to monitored hosts
				; Defaults to 100 ms
;notifymimetype=text/plain	; Allow overriding of mime type in MWI NOTIFY
;checkmwi=10			; Default time between mailbox checks for peers
;vmexten=voicemail		; dialplan extension to reach mailbox sets the 
				; Message-Account in the MWI notify message 
				; defaults to "asterisk"
;disallow=all			; First disallow all codecs
;allow=ulaw			; Allow codecs in order of preference
;allow=ilbc			; see doc/rtp-packetization for framing options
;
; This option specifies a preference for which music on hold class this channel
; should listen to when put on hold if the music class has not been set on the
; channel with Set(CHANNEL(musicclass)=whatever) in the dialplan, and the peer
; channel putting this one on hold did not suggest a music class.
;
; This option may be specified globally, or on a per-user or per-peer basis.
;
;mohinterpret=default
;
; This option specifies which music on hold class to suggest to the peer channel
; when this channel places the peer on hold. It may be specified globally or on
; a per-user or per-peer basis.
;
;mohsuggest=default
;
;language=en			; Default language setting for all users/peers
				; This may also be set for individual users/peers
;relaxdtmf=yes			; Relax dtmf handling
;rtptimeout=60			; Terminate call if 60 seconds of no RTP or RTCP activity
				; when we're not on hold. This is to be able to hangup
				; a call in the case of a phone disappearing from the net,
				; like a powerloss or grandma tripping over a cable.
;rtpholdtimeout=300		; Terminate call if 300 seconds of no RTP or RTCP activity
				; when we're on hold (must be > rtptimeout)
;trustrpid = no			; If Remote-Party-ID should be trusted
;sendrpid = yes			; If Remote-Party-ID should be sent
;progressinband=never		; If we should generate in-band ringing always
				; use 'never' to never use in-band signalling, even in cases
				; where some buggy devices might not render it
				; Valid values: yes, no, never Default: never
;useragent=Asterisk PBX		; Allows you to change the user agent string
;promiscredir = no      	; If yes, allows 302 or REDIR to non-local SIP address
	                       	; Note that promiscredir when redirects are made to the
       	                	; local system will cause loops since Asterisk is incapable
       	                	; of performing a "hairpin" call.
;usereqphone = no		; If yes, ";user=phone" is added to uri that contains
				; a valid phone number
;dtmfmode = rfc2833		; Set default dtmfmode for sending DTMF. Default: rfc2833
				; Other options: 
				; info : SIP INFO messages
				; inband : Inband audio (requires 64 kbit codec -alaw, ulaw)
				; auto : Use rfc2833 if offered, inband otherwise

;compactheaders = yes		; send compact sip headers.
;
;videosupport=yes		; Turn on support for SIP video. You need to turn this on
				; in the this section to get any video support at all.
				; You can turn it off on a per peer basis if the general
				; video support is enabled, but you can't enable it for
				; one peer only without enabling in the general section.
;maxcallbitrate=384		; Maximum bitrate for video calls (default 384 kb/s)
				; Videosupport and maxcallbitrate is settable
				; for peers and users as well
;callevents=no			; generate manager events when sip ua 
				; performs events (e.g. hold)
;limitpeersonly=no		; Apply all call limits ("limit=") only to peers, never
				; to users. This improves handling of call limits
				; and device states in certain situations. The user part
				; of a type=friend will still be affected by the call
				; limit, but Asterisk will only use one object for
				; counting the simultaneous calls.
;alwaysauthreject = yes		; When an incoming INVITE or REGISTER is to be rejected,
 		    		; for any reason, always reject with '401 Unauthorized'
 				; instead of letting the requester know whether there was
 				; a matching user or peer for their request

;g726nonstandard = yes		; If the peer negotiates G726-32 audio, use AAL2 packing
				; order instead of RFC3551 packing order (this is required
				; for Sipura and Grandstream ATAs, among others). This is
				; contrary to the RFC3551 specification, the peer _should_
				; be negotiating AAL2-G726-32 instead :-(

;
; If regcontext is specified, Asterisk will dynamically create and destroy a
; NoOp priority 1 extension for a given peer who registers or unregisters with
; us and have a "regexten=" configuration item.  
; Multiple contexts may be specified by separating them with '&'. The 
; actual extension is the 'regexten' parameter of the registering peer or its
; name if 'regexten' is not provided.  If more than one context is provided,
; the context must be specified within regexten by appending the desired
; context after '@'.  More than one regexten may be supplied if they are 
; separated by '&'.  Patterns may be used in regexten.
;
;regcontext=sipregistrations
;
;--------------------------- SIP DEBUGGING ---------------------------------------------------
;sipdebug = yes			; Turn on SIP debugging by default, from
				; the moment the channel loads this configuration
;recordhistory=yes		; Record SIP history by default 
				; (see sip history / sip no history)
;dumphistory=yes		; Dump SIP history at end of SIP dialogue
				; SIP history is output to the DEBUG logging channel


;--------------------------- STATUS NOTIFICATIONS (SUBSCRIPTIONS) ----------------------------
; You can subscribe to the status of extensions with a "hint" priority
; (See extensions.conf.sample for examples)
; chan_sip support two major formats for notifications: dialog-info and SIMPLE 
; Note: Subscriptions does not work if you have a realtime dialplan and use the
; realtime switch.
;
;allowsubscribe=no		; Disable support for subscriptions. (Default is yes)
;subscribecontext = default	; Set a specific context for SUBSCRIBE requests
				; Useful to limit subscriptions to local extensions
				; Settable per peer/user also
;notifyringing = yes		; Notify subscriptions on RINGING state (default: no)
;notifyhold = yes		; Notify subscriptions on HOLD state (default: no)
				; Turning on notifyringing and notifyhold will add a lot
				; more database transactions if you are using realtime.

;----------------------------------------- T.38 FAX PASSTHROUGH SUPPORT -----------------------
;
; This setting is available in the [general] section as well as in device configurations.
; Setting this to yes, enables T.38 fax (UDPTL) passthrough on SIP to SIP calls, provided
; both parties have T38 support enabled in their Asterisk configuration (either general or
; peer/user/friend sections)
;
; t38pt_udptl = yes            ; Default false
;
;----------------------------------------- OUTBOUND SIP REGISTRATIONS  ------------------------
; Asterisk can register as a SIP user agent to a SIP proxy (provider)
; Format for the register statement is:
;       register => user[:secret[:authuser]]@host[:port][/extension]
;
; If no extension is given, the 's' extension is used. The extension needs to
; be defined in extensions.conf to be able to accept calls from this SIP proxy
; (provider).
;
; host is either a host name defined in DNS or the name of a section defined
; below.
;
; A similar effect can be achieved by adding a "callbackextension" option in a peer section.
; this is equivalent to having the following line in the general section:
;
;	register => username:secret@host/callbackextension
;
; and more readable because you don't have to write the parameters in two places
; (note that the "port" is ignored - this is a bug that should be fixed).
;
; Examples:
;
;register => 1234:password@mysipprovider.com	
;
;     This will pass incoming calls to the 's' extension
;
;
;register => 2345:password@sip_proxy/1234
;
;    Register 2345 at sip provider 'sip_proxy'.  Calls from this provider
;    connect to local extension 1234 in extensions.conf, default context,
;    unless you configure a [sip_proxy] section below, and configure a
;    context.
;    Tip 1: Avoid assigning hostname to a sip.conf section like [provider.com]
;    Tip 2: Use separate type=peer and type=user sections for SIP providers
;           (instead of type=friend) if you have calls in both directions
  
;registertimeout=20		; retry registration calls every 20 seconds (default)
;registerattempts=10		; Number of registration attempts before we give up
				; 0 = continue forever, hammering the other server
				; until it accepts the registration
				; Default is 0 tries, continue forever

;----------------------------------------- NAT SUPPORT ------------------------
; The externip, externhost and localnet settings are used if you use Asterisk
; behind a NAT device to communicate with services on the outside.

;externip = 200.201.202.203	; Address that we're going to put in outbound SIP
				; messages if we're behind a NAT

				; The externip and localnet is used
				; when registering and communicating with other proxies
				; that we're registered with
;externhost=foo.dyndns.net	; Alternatively you can specify an 
				; external host, and Asterisk will 
				; perform DNS queries periodically.  Not
				; recommended for production 
				; environments!  Use externip instead
;externrefresh=10		; How often to refresh externhost if 
				; used
				; You may add multiple local networks.  A reasonable 
				; set of defaults are:
;localnet=192.168.0.0/255.255.0.0; All RFC 1918 addresses are local networks
;localnet=10.0.0.0/255.0.0.0	; Also RFC1918
;localnet=172.16.0.0/12		; Another RFC1918 with CIDR notation
;localnet=169.254.0.0/255.255.0.0 ;Zero conf local network

; The nat= setting is used when Asterisk is on a public IP, communicating with
; devices hidden behind a NAT device (broadband router).  If you have one-way
; audio problems, you usually have problems with your NAT configuration or your
; firewall's support of SIP+RTP ports.  You configure Asterisk choice of RTP
; ports for incoming audio in rtp.conf
;
;nat=no				; Global NAT settings  (Affects all peers and users)
                                ; yes = Always ignore info and assume NAT
                                ; no = Use NAT mode only according to RFC3581 (;rport)
                                ; never = Never attempt NAT mode or RFC3581 support
				; route = Assume NAT, don't send rport 
				; (work around more UNIDEN bugs)

;----------------------------------- MEDIA HANDLING --------------------------------
; By default, Asterisk tries to re-invite the audio to an optimal path. If there's
; no reason for Asterisk to stay in the media path, the media will be redirected.
; This does not really work with in the case where Asterisk is outside and have
; clients on the inside of a NAT. In that case, you want to set canreinvite=nonat
;
;canreinvite=yes		; Asterisk by default tries to redirect the
				; RTP media stream (audio) to go directly from
				; the caller to the callee.  Some devices do not
				; support this (especially if one of them is behind a NAT).
				; The default setting is YES. If you have all clients
				; behind a NAT, or for some other reason wants Asterisk to
				; stay in the audio path, you may want to turn this off.

				; This setting also affect direct RTP
				; at call setup (a new feature in 1.4 - setting up the
				; call directly between the endpoints instead of sending
				; a re-INVITE).

;canreinvite=nonat		; An additional option is to allow media path redirection
				; (reinvite) but only when the peer where the media is being
				; sent is known to not be behind a NAT (as the RTP core can
				; determine it based on the apparent IP address the media
				; arrives from).

;canreinvite=update		; Yet a third option... use UPDATE for media path redirection,
				; instead of INVITE. This can be combined with 'nonat', as
				; 'canreinvite=update,nonat'. It implies 'yes'.

;----------------------------------------- REALTIME SUPPORT ------------------------
; For additional information on ARA, the Asterisk Realtime Architecture,
; please read realtime.txt and extconfig.txt in the /doc directory of the
; source code.
;
;rtcachefriends=yes		; Cache realtime friends by adding them to the internal list
				; just like friends added from the config file only on a
				; as-needed basis? (yes|no)

;rtsavesysname=yes		; Save systemname in realtime database at registration
				; Default= no

;rtupdate=yes			; Send registry updates to database using realtime? (yes|no)
				; If set to yes, when a SIP UA registers successfully, the ip address,
				; the origination port, the registration period, and the username of
				; the UA will be set to database via realtime. 
				; If not present, defaults to 'yes'.
;rtautoclear=yes		; Auto-Expire friends created on the fly on the same schedule
				; as if it had just registered? (yes|no|<seconds>)
				; If set to yes, when the registration expires, the friend will
				; vanish from the configuration until requested again. If set
				; to an integer, friends expire within this number of seconds
				; instead of the registration interval.

;ignoreregexpire=yes		; Enabling this setting has two functions:
				;
				; For non-realtime peers, when their registration expires, the
				; information will _not_ be removed from memory or the Asterisk database
				; if you attempt to place a call to the peer, the existing information
				; will be used in spite of it having expired
				;
				; For realtime peers, when the peer is retrieved from realtime storage,
				; the registration information will be used regardless of whether
				; it has expired or not; if it expires while the realtime peer 
				; is still in memory (due to caching or other reasons), the 
				; information will not be removed from realtime storage

;----------------------------------------- SIP DOMAIN SUPPORT ------------------------
; Incoming INVITE and REFER messages can be matched against a list of 'allowed'
; domains, each of which can direct the call to a specific context if desired.
; By default, all domains are accepted and sent to the default context or the
; context associated with the user/peer placing the call.
; Domains can be specified using:
; domain=<domain>[,<context>]
; Examples:
; domain=myasterisk.dom
; domain=customer.com,customer-context
;
; In addition, all the 'default' domains associated with a server should be
; added if incoming request filtering is desired.
; autodomain=yes
;
; To disallow requests for domains not serviced by this server:
; allowexternaldomains=no

;domain=mydomain.tld,mydomain-incoming
				; Add domain and configure incoming context
				; for external calls to this domain
;domain=1.2.3.4			; Add IP address as local domain
				; You can have several "domain" settings
;allowexternalinvites=no	; Disable INVITE and REFER to non-local domains
				; Default is yes
;autodomain=yes			; Turn this on to have Asterisk add local host
				; name and local IP to domain list.

; fromdomain=mydomain.tld 	; When making outbound SIP INVITEs to
                          	; non-peers, use your primary domain "identity"
                          	; for From: headers instead of just your IP
                          	; address. This is to be polite and
                          	; it may be a mandatory requirement for some
                          	; destinations which do not have a prior
                          	; account relationship with your server. 

;------------------------------ JITTER BUFFER CONFIGURATION --------------------------
; jbenable = yes              ; Enables the use of a jitterbuffer on the receiving side of a
                              ; SIP channel. Defaults to "no". An enabled jitterbuffer will
                              ; be used only if the sending side can create and the receiving
                              ; side can not accept jitter. The SIP channel can accept jitter,
                              ; thus a jitterbuffer on the receive SIP side will be used only
                              ; if it is forced and enabled.

; jbforce = no                ; Forces the use of a jitterbuffer on the receive side of a SIP
                              ; channel. Defaults to "no".

; jbmaxsize = 200             ; Max length of the jitterbuffer in milliseconds.

; jbresyncthreshold = 1000    ; Jump in the frame timestamps over which the jitterbuffer is
                              ; resynchronized. Useful to improve the quality of the voice, with
                              ; big jumps in/broken timestamps, usually sent from exotic devices
                              ; and programs. Defaults to 1000.

; jbimpl = fixed              ; Jitterbuffer implementation, used on the receiving side of a SIP
                              ; channel. Two implementations are currently available - "fixed"
                              ; (with size always equals to jbmaxsize) and "adaptive" (with
                              ; variable size, actually the new jb of IAX2). Defaults to fixed.

; jblog = no                  ; Enables jitterbuffer frame logging. Defaults to "no".
;-----------------------------------------------------------------------------------

[authentication]
; Global credentials for outbound calls, i.e. when a proxy challenges your
; Asterisk server for authentication. These credentials override
; any credentials in peer/register definition if realm is matched.
;
; This way, Asterisk can authenticate for outbound calls to other
; realms. We match realm on the proxy challenge and pick an set of 
; credentials from this list
; Syntax:
;	auth = <user>:<secret>@<realm>
;	auth = <user>#<md5secret>@<realm>
; Example:
;auth=mark:topsecret@digium.com
; 
; You may also add auth= statements to [peer] definitions 
; Peer auth= override all other authentication settings if we match on realm

;------------------------------------------------------------------------------
; Users and peers have different settings available. Friends have all settings,
; since a friend is both a peer and a user
;
; User config options:        Peer configuration:
; --------------------        -------------------
; context                     context
; callingpres		      callingpres
; permit                      permit
; deny                        deny
; secret                      secret
; md5secret                   md5secret
; dtmfmode                    dtmfmode
; canreinvite                 canreinvite
; nat                         nat
; callgroup                   callgroup
; pickupgroup                 pickupgroup
; language                    language
; allow                       allow
; disallow                    disallow
; insecure                    insecure
; trustrpid                   trustrpid
; progressinband              progressinband
; promiscredir                promiscredir
; useclientcode               useclientcode
; accountcode                 accountcode
; setvar                      setvar
; callerid		      callerid
; amaflags		      amaflags
; call-limit		      call-limit
; allowoverlap		      allowoverlap
; allowsubscribe	      allowsubscribe
; allowtransfer	      	      allowtransfer
; subscribecontext	      subscribecontext
; videosupport		      videosupport
; maxcallbitrate	      maxcallbitrate
; rfc2833compensate           mailbox
;                             username
;                             template
;                             fromdomain
;                             regexten
;                             fromuser
;                             host
;                             port
;                             qualify
;                             defaultip
;                             rtptimeout
;                             rtpholdtimeout
;                             sendrpid
;                             outboundproxy
;                             rfc2833compensate
;                             callbackextension

;[sip_proxy]
; For incoming calls only. Example: FWD (Free World Dialup)
; We match on IP address of the proxy for incoming calls 
; since we can not match on username (caller id)
;type=peer
;context=from-fwd
;host=fwd.pulver.com

;[sip_proxy-out]
;type=peer          			; we only want to call out, not be called
;secret=guessit
;username=yourusername			; Authentication user for outbound proxies
;fromuser=yourusername			; Many SIP providers require this!
;fromdomain=provider.sip.domain	
;host=box.provider.com
;usereqphone=yes			; This provider requires ";user=phone" on URI
;call-limit=5				; permit only 5 simultaneous outgoing calls to this peer
;outboundproxy=proxy.provider.domain	; send outbound signaling to this proxy, not directly to the peer
				; Call-limits will not be enforced on real-time peers,
				; since they are not stored in-memory

;--- sample definition for a provider
;[provider1]
;type=peer
;host=sip.provider1.com
;username=4015552299		; how your provider knows you
;secret=youwillneverguessit
;callbackextension=123		; Register with this server and require calls coming back to this extension

;------------------------------------------------------------------------------
; Definitions of locally connected SIP devices
;
; type = user	a device that authenticates to us by "from" field to place calls
; type = peer	a device we place calls to or that calls us and we match by host
; type = friend two configurations (peer+user) in one
;
; For device names, we recommend using only a-z, numerics (0-9) and underscore
; 
; For local phones, type=friend works most of the time
;
; If you have one-way audio, you probably have NAT problems. 
; If Asterisk is on a public IP, and the phone is inside of a NAT device
; you will need to configure nat option for those phones.
; Also, turn on qualify=yes to keep the nat session open
;
; Because you might have a large number of similar sections, it is generally
; convenient to use templates for the common parameters, and add them
; the the various sections. Examples are below, and we can even leave
; the templates uncommented as they will not harm:

[basic-options](!)		; a template
	dtmfmode=rfc2833
	context=from-office
	type=friend

[natted-phone](!,basic-options)	; another template inheriting basic-options
	nat=yes
	canreinvite=no
	host=dynamic

[public-phone](!,basic-options)	; another template inheriting basic-options
	nat=no
	canreinvite=yes

[my-codecs](!)		; a template for my preferred codecs
	disallow=all
	allow=ilbc
	allow=g729
	allow=gsm
	allow=g723
	allow=ulaw

[ulaw-phone](!)		; and another one for ulaw-only
	disallow=all
	allow=ulaw

; and finally instantiate a few phones
;
; [2133](natted-phone,my-codecs)
;	secret = peekaboo
; [2134](natted-phone,ulaw-hone)
;	secret = not_very_secret
; [2136](public-phone,ulaw-hone)
;	secret = not_very_secret_either
; ...
;

; Standard configurations not using templates look like this:
;
;[grandstream1]
;type=friend 			
;context=from-sip		; Where to start in the dialplan when this phone calls
;callerid=John Doe <1234>	; Full caller ID, to override the phones config
				; on incoming calls to Asterisk
;host=192.168.0.23		; we have a static but private IP address
				; No registration allowed
;nat=no				; there is not NAT between phone and Asterisk
;canreinvite=yes		; allow RTP voice traffic to bypass Asterisk
;dtmfmode=info			; either RFC2833 or INFO for the BudgeTone
;call-limit=1			; permit only 1 outgoing call and 1 incoming call at a time
				; from the phone to asterisk
				; 1 for the explicit peer, 1 for the explicit user,
				; remember that a friend equals 1 peer and 1 user in
				; memory
				; This will affect your subscriptions as well.
				; There is no combined call counter for a "friend"
				; so there's currently no way in sip.conf to limit
				; to one inbound or outbound call per phone. Use
				; the group counters in the dial plan for that.
				;
;mailbox=1234@default		; mailbox 1234 in voicemail context "default"
;disallow=all			; need to disallow=all before we can use allow=
;allow=ulaw			; Note: In user sections the order of codecs
				; listed with allow= does NOT matter!
;allow=alaw
;allow=g723.1			; Asterisk only supports g723.1 pass-thru!
;allow=g729			; Pass-thru only unless g729 license obtained
;callingpres=allowed_passed_screen	; Set caller ID presentation
				; See README.callingpres for more information


;[xlite1]
; Turn off silence suppression in X-Lite ("Transmit Silence"=YES)!
; Note that Xlite sends NAT keep-alive packets, so qualify=yes is not needed
;type=friend
;regexten=1234			; When they register, create extension 1234
;callerid="Jane Smith" <5678>
;host=dynamic			; This device needs to register
;nat=yes			; X-Lite is behind a NAT router
;canreinvite=no			; Typically set to NO if behind NAT
;disallow=all
;allow=gsm			; GSM consumes far less bandwidth than ulaw
;allow=ulaw
;allow=alaw
;mailbox=1234@default,1233@default	; Subscribe to status of multiple mailboxes


;[snom]
;type=friend			; Friends place calls and receive calls
;context=from-sip		; Context for incoming calls from this user
;secret=blah
;subscribecontext=localextensions	; Only allow SUBSCRIBE for local extensions
;language=de			; Use German prompts for this user 
;host=dynamic			; This peer register with us
;dtmfmode=inband		; Choices are inband, rfc2833, or info
;defaultip=192.168.0.59		; IP used until peer registers
;mailbox=1234@context,2345      ; Mailbox(-es) for message waiting indicator
;subscribemwi=yes		; Only send notifications if this phone 
				; subscribes for mailbox notification
;vmexten=voicemail		; dialplan extension to reach mailbox 
				; sets the Message-Account in the MWI notify message
				; defaults to global vmexten which defaults to "asterisk"
;disallow=all
;allow=ulaw			; dtmfmode=inband only works with ulaw or alaw!


;[polycom]
;type=friend			; Friends place calls and receive calls
;context=from-sip		; Context for incoming calls from this user
;secret=blahpoly
;host=dynamic			; This peer register with us
;dtmfmode=rfc2833		; Choices are inband, rfc2833, or info
;username=polly			; Username to use in INVITE until peer registers
				; Normally you do NOT need to set this parameter
;disallow=all
;allow=ulaw                     ; dtmfmode=inband only works with ulaw or alaw!
;progressinband=no		; Polycom phones don't work properly with "never"


;[pingtel]
;type=friend
;secret=blah
;host=dynamic
;insecure=port			; Allow matching of peer by IP address without 
				; matching port number
;insecure=invite		; Do not require authentication of incoming INVITEs
;insecure=port,invite		; (both)
;qualify=1000			; Consider it down if it's 1 second to reply
				; Helps with NAT session
				; qualify=yes uses default value
;
; Call group and Pickup group should be in the range from 0 to 63
;
;callgroup=1,3-4		; We are in caller groups 1,3,4
;pickupgroup=1,3-5		; We can do call pick-p for call group 1,3,4,5
;defaultip=192.168.0.60		; IP address to use if peer has not registered
;deny=0.0.0.0/0.0.0.0		; ACL: Control access to this account based on IP address
;permit=192.168.0.60/255.255.255.0

;[cisco1]
;type=friend
;secret=blah
;qualify=200			; Qualify peer is no more than 200ms away
;nat=yes			; This phone may be natted
				; Send SIP and RTP to the IP address that packet is 
				; received from instead of trusting SIP headers 
;host=dynamic			; This device registers with us
;canreinvite=no			; Asterisk by default tries to redirect the
				; RTP media stream (audio) to go directly from
				; the caller to the callee.  Some devices do not
				; support this (especially if one of them is 
				; behind a NAT).
;defaultip=192.168.0.4		; IP address to use until registration
;username=goran			; Username to use when calling this device before registration
				; Normally you do NOT need to set this parameter
;setvar=CUSTID=5678		; Channel variable to be set for all calls from this device

;[pre14-asterisk]
;type=friend
;secret=digium
;host=dynamic
;rfc2833compensate=yes		; Compensate for pre-1.4 DTMF transmission from another Asterisk machine.
				; You must have this turned on or DTMF reception will work improperly.