From d1c6d6bc72d697c015407a83bd213ab232db8d6b Mon Sep 17 00:00:00 2001
From: Andreas Eversberg <jolly@eversberg.eu>
Date: Fri, 9 Dec 2016 16:42:19 +0100
Subject: [PATCH] work on docs

---
 docs/amps.html  | 3 +++
 docs/index.html | 2 --
 docs/setup.html | 4 ++--
 3 files changed, 5 insertions(+), 4 deletions(-)

diff --git a/docs/amps.html b/docs/amps.html
index 6ec13fb..6656883 100644
--- a/docs/amps.html
+++ b/docs/amps.html
@@ -10,6 +10,8 @@
 
 <center><img src="amps.jpg"/></center>
 
+<center><h1>*this doc is under construction*</h1></center>
+
 <ul>
 	<li><a href="#history">History</a>
 	<li><a href="#howitworks">How it works</a>
@@ -24,6 +26,7 @@ History
 <p>
 *TBD*
 
+
 The Advanced Mobile Phone Service (AMPS) was an analog cellular mobile phone system developed by Bell Labs.
 From 1968 to 1983 the Bell Labs worked out the system, while Motorola was developing the cellular phone.
 Dr. Martin Cooper produced the first handheld phone "DynaTAC8000x", the famous Brick Phone.
diff --git a/docs/index.html b/docs/index.html
index 14d7500..ab3e4fb 100644
--- a/docs/index.html
+++ b/docs/index.html
@@ -55,8 +55,6 @@ This project is pure software that requires a transmitter and a receiver connect
 A second sound card or ISDN card is used to route calls from and to the mobile phone.
 </p>
 
-<center><h1>*this doc is under construction*</h1></center>
-
 <center>
 <ul>
 	<li><a href="setup.html">Radio setup</a></li>
diff --git a/docs/setup.html b/docs/setup.html
index 9ba8353..cae6034 100644
--- a/docs/setup.html
+++ b/docs/setup.html
@@ -40,7 +40,7 @@ This image shows a two-band amateur radio receiver without limitations for the f
 <p>
 I built several transmitters out of modified taxi radios.
 It features a simple digital PLL (configurable by jumpers) and allows to directly connect the audio signal to the oscillator.
-This is highly recommended for the C-Netz, because signaling is done by sifting the carrier directly.
+This is highly recommended for the C-Netz, because signaling is done by modulating (shifting) the carrier directly.
 One unit has a switch to change between A-Netz and B-Netz (2-meter version) and the other units to change between C-Netz and NMT (70-cm version).
 I added an input to switch between two channels for the B-Netz.
 (Whenever a B-Netz phone is paged, the channel must be temporarily switched to the paging channel.)
@@ -135,7 +135,7 @@ I use 10 K resistor for connecting radio output (discriminator) to microphone in
 Connect the ground of input and output to one end of the resistor. (shown in the picture as 'Masse')
 Select this side to which the slider moves, if the knob turned all the way left (or moved all the way down).
 Connect the input signal ('Signaleingang') to the other end of the resistor.
-At least connect the output signal ('Signalausgang') to the slider of the resistor.
+Finally connect the output signal ('Signalausgang') to the slider of the resistor.
 </p>
 
 <p>