Remove the built time resampling selection and link both options.
Move the normal push/pullBuffer() calls back to the base class and
overload them in the inherited resampling class.
USRP2/N2xx devices are the only devices that require resampling so
return that resampling is necessary on the device open(), which is
the point at which the device type will be known.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
The GSM transceiver only operates at a whole number multiple of
the GSM rate and doesn't care about the actual device rate and
if resampling is used. Therefore GSM specific portion of the
transceiver should only need to submit the samples-per-symbol
value to the device interface.
Then, the device should be able to determine the appropriate
sample rate (400 ksps or 270.833 ksps) and if resampling is
appropriate.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
The transceiver only uses a single integer oversampling value,
which is more simply referred to as samples-per-symbol.
mRadioOversampling --> mSPS
mTransceiverOversampling (removed)
Signed-off-by: Thomas Tsou <tom@tsou.cc>
Previously, two timing correction values were used for UHD devices
depending on the sample rate of 270.833e3 or 400e3 for native GSM or
resampled device rate respectively. The correction values compensate
for residual timing effects due to analog component delays, filters
lag times, and general fudge factors. These values are device
specific and over-generalized by the two value configuration.
This patch adds the following struct to store these correction
values by device type and sample rate - through samples-per-symbol.
struct uhd_dev_offset {
enum uhd_dev_type type;
int sps;
double offset;
};
Signed-off-by: Thomas Tsou <tom@tsou.cc>
Set optional transmit and receive antennas from database configuration
file. Use default antenna values on empty string or if option does not
exist.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
Without this patch, if SAMPSPERSYM is set bigger than 1, then
erratic behaviour will occur.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@4633 19bc5d8c-e614-43d4-8b26-e1612bc8e597
UHD accepts optional 'args' that can be used for device descriptions
such as IP address, device type, etc. Allow these to be passed in on
the transceiver command line as the third argument (number of supported
carriers is the second argument). This option benefits those who may
have multiple UHD devices attached to a single system.
This option is not yet supported by GSM core and requires starting the
transceiver independently on the command line. This option has no
effect when USRP1 is used.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@4315 19bc5d8c-e614-43d4-8b26-e1612bc8e597
Device errors regarding properties such as sample
rate or frequency tuning are almost always fatal and
lead to the common error "assuming TRX is dead".
Make sure that these errors are clearly presented to
the user.
Signed-off-by: Thomas Tsou <ttsou@vt.edu>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2700 19bc5d8c-e614-43d4-8b26-e1612bc8e597
For network based devices (USRP2, N200, etc.), increase the
latency from 2 to 3 frames, which effectively buffers more
samples on the host in front of the Ethernet interface.
USB devices (USRP1 and B100) utilize an adaptive mechanism
so they are less effected by this value.
Signed-off-by: Thomas Tsou <ttsou@vt.edu>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2685 19bc5d8c-e614-43d4-8b26-e1612bc8e597
The low-level RadioDevice interface is agnostic to libusrp
or uhd based devices. 'make' allocates and returns a
pointer to a generic RadioDevice implemented for whatever
class of device determined at compile time.
Signed-off-by: Thomas Tsou <ttsou@vt.edu>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2684 19bc5d8c-e614-43d4-8b26-e1612bc8e597
Thomas Tsou