This patch extends the test_messages test to show the number of dummy
packets that has been passed to sendto(). This way, dummy packets are
even being counted when sendto() itself failes (e.g. due to the fd
being -1).
Sponsored-by: On-Waves ehf
This modifies the test MGCP messages to include M:recvonly (CRCX),
M:sendrecv (MDCX) and M:sendonly (MDCX) outputs the resulting
output_enabled flags and the conn_mode after processing the message.
Sponsored-by: On-Waves ehf
Currently, all timestamps are force to SeqNo*d + C which is more than
required by the nanoBTS which seems to be sensitive to alignment
errors only (dTS != k*d, d = ptime * rate = 160).
This patch replaces the force_constant_timing feature by a
force_aligned_timing feature. The timestamp offset will only be
changed (and timestamp errors counted) when the alignment does not
match to the raster based on ptime (default 20ms).
The VTY interface does not change.
Sponsored-by: On-Waves ehf
Currently the counter and output timestamp values are written out for
each packet. This makes it difficult to see in the diffs what has
been changed significantly.
This patch changes this by showing differences for those
values. The absolute input values are also shown now. In addition,
the sequence numbers (the difference for the output value) are
written, too.
Sponsored-by: On-Waves ehf
This adds two test cases:
1. Packet repetition (dSeq=0, dTS=0)
2. Broken seqNo (dSeq=0, dTS=160)
The second had been already present in the test cases, but it was a
mere copy&paste mistake which turned out to be rather helpful. This
patch therefore turns it into a documented test case.
Sponsored-by: On-Waves ehf
Currently the SDP 'ptime' media attribute is never set in generated
MGCP responses.
This patch optionally includes the 'ptime' attribute if
packet_duration_ms is != 0. This behaviour can be enabled/disabled
by using the VTY command "sdp audio-payload send-ptime" (enabled by
default).
Sponsored-by: On-Waves ehf
This patch parses the 'ptime' and 'maxptime' SDP attributes, and the
SDP rate information and sets up packet_duration_ms accordingly. If
the packet duration is unknown or allows for different values (e.g.
because 'ptime' uses a range or 'maxptime' allows for more than one
frame) the duration is set to 0.
Sponsored-by: On-Waves ehf
Currently the local connection options have been stored as a string.
This patch replaces this string by a struct (that still contains a
string) along with the parsed fields (only the packetization period
at the moment).
It also re-adds the calls to set_local_cx_options() to the
handle_create_con() and handle_modify_con() functions. Except for
the test program this has no side effects, since the LCO values
aren't used yet.
This also adds additional MDCX tests (based on MDCX4) to test the
analysis of different combinations of 'p' and 'ptime' fields.
Sponsored-by: On-Waves ehf
This forces the output timing to fulfill
dTS = dSegNo * fixedPacketDuration
where dSegNo = seqNo - lastSeqNo.
If timestamp patching is enabled, the output timestamp will be set
to lastTimestamp + dTS. This kind of relative updating is used to
handle seqNo- and timestamp-wraparounds properly.
The updating of timestamp and SSRC has been separated and the patch
field of mgcp_rtp_state has been renamed to patch_ssrc to reflect
it's semantics more closely. The offset fields are now used always
and will change the corresponding header field if they are != 0.
Ticket: OW#1065
Sponsored-by: On-Waves ehf
The ssrc has been used without respect to proper byte ordering in
mgcp_patch_and_count(). This only affected log messages.
This patch introduces a new variable 'ssrc' that takes the value of
the SSRC in proper byte order.
Sponsored-by: On-Waves ehf
This adds datastructures and a VTY frontend to configure the
different type of RTP header patching: SSRC and timestamp.
Note that timestamp patching is not yet implemented.
Sponsored-by: On-Waves ehf
The tsdelta computation and error detection didn't handle the
intialisation phase properly.
This patches fixes this by skipping the output timing validation
when the SSRCs don't match.
Sponsored-by: On-Waves ehf
This patch extends the existing RTP error check test by adding a
check for timestamp errors after SSRC changes and a check for a
segno delta of 2 (with a timestamp delta of 320).
To test SSRC patching too, a corresponding line will be written on
each SSRC change that has been detected in the output stream.
In addition there is now support for selectively enabling/disabling
SSRC and timestamp patching. The RTP test sequence is repeated for
all combinations thereof.
Sponsored-by: On-Waves ehf
So far the SDP part of the CRCX message has been ignored by the MGW.
This patch adds SDP parsing for this case, eventually updating the
net end's payload type and connection parameters.
Sponsored-by: On-Waves ehf
This patch add the for_each_line macro based on a strline_r()
function (similar to strtok_r()), that is also part of this patch.
This strline_r() function is tolerant with respect to line endings,
it supports CR-only, CRLF, and LF-only and any combinations thereof
(note that a CRLF is always detected as a single line break).
Similar to for_each_non_empty_line (the former for_each_line) where
the 'save' pointer needed to be initialised by a call to strtok_r(),
the new for_each_line macro expects, that the 'save' pointer has been
initialised by a call to strline_r(). Also note, that
for_each_line/strline_r and for_each_non_empty_line/strtok_r may use
the 'save' pointer differently, so calls to them can not be mixed.
Sponsored-by: On-Waves ehf
The current implementation increments the seqno but does not increment
the RTP timestamp, leading to two identical timestamps following one
after the other.
This patch fixes this by adding the computed tsdelta when the offset
is calulated. In the unlikely case, that a tsdelta hasn't been
computed yet when the SSRC changes, a tsdelta is computed based on
the RTP rate and a RTP packet duration of 20ms (one speech frame per
channel and packet). If the RTP rate is not known, a rate of 8000 is
assumed.
Note that this approach presumes, that the per RTP packet duration
(in samples) is the same for the last two packets of the stream being
replaced (the first one).
Sponsored-by: On-Waves ehf
This patch adds a test case to check, whether RTP timestamps are
generated properly after SSRC changes and whether the error counters
work properly.
Sponsored-by: On-Waves ehf
This patch modifies the patch_and_count() function to check for RTP
timestamp inconsistencies. It basically checks, whether dTS/dSeqNo
remains constant. If this fails, the corresponding counter is
incremented. There are four counter for this: Incoming and outgoing,
each for streams from the BTS and the net.
Note that this approach presumes, that the per RTP packet duration
(in samples) remains the same throughout the entire stream. Changing
the number of speech frames per channel and packet will be detected
as error.
In addition, the VTY command 'show mgcp' is extended by an optional
'stats' to show the counter values, too.
Ticket: OW#964
Sponsored-by: On-Waves ehf
We want to send a TRAP with the MGCP statistics from the NAT and
the connected BSC. The BSC endpoint can be either released because
of a DLCX from the MGCP CallAgent or the SCCP Connection release on
the A-link.
This is why we need to queue the statistics when the deleting the
endpoint on the BSC. The processing is continued once the response
arrives. This code assumes that the response of the DLCX will be sent
by the remote side. The current amount of outstanding responses can be
seen on the VTY. This assumption is based on the fact that the BSC has
already responded to the CRCX and maybe to the MDCX.
The MGCP RFC is bended to prefix the transaction identifier with "nat-"
to easily detect the response and hand it to the handler. This will
then parse the response and generate the TRAP. The current version is
v1. We assume that the transaction space is big enough and we will
not re-assign the transaction identifier too early.
MGCP is used over UDP and a response might be lost. The MGCP RFC
asks for keeping a list of responses and then using the previous
response to answer a duplicate request. I tried to conserve memory
and just wanted to remember the last transaction identifier and
result-code and re-generate the result from that. This made the
code look bad and this is why the entire response will now be stored.
It sadly increases the memory usage but can not be avoided at this
time.
Remove the msg->l3h pointer for the RQNT callback as strtok has
modified the content of it.
Calculate the expected packages and packet loss as of RFC 3550.
The values should be clamped but our packet loss counter is 32
bits and not 24 and we should clamp at other values but I am
waiting for some issues first before dealing with that.
Instead of building complex manual byte-wise parsers, we simply use two
strtok_r loops: one iterating over all the lines, the next one
iterating over the invididual space-separated elements in the first line.
The benefit is that we now accept \r, \n or \r\n, or any multiple of
them as line ending. This works around incompliant MGCP implementations
like that of Zynetix MSC.
Addition: mgcp_analyze_header returns 0 when all out parameters have
been set.
Signed-off-by: Holger Hans Peter Freyther <zecke@selfish.org>
Use the libosmocore code to ignore certain signals by
default (e.g. SIGHUP, SIGPIPE) and use the new code to
create a default stderr logging target and initialize
it properly.
libosmogsm is a new library that is distributed in the libosmocore.
Now, openbsc depends on it. This patch gets openbsc with this
change.
This patch also rewrites all include path to the new
osmocom/[gsm|core]
Signed-off-by: Pablo Neira Ayuso <pablo@gnumonks.org>
Jacob Erlbeck
Alexander Huemer
Harald Welte