Find the Cell Identifier from the Complete Layer3 Information and
store it for future reference. We could begin to verify that the
LAC/CI used really belongs to the BSC.
The name sccp_connection is used in the osmo-sccp code, sccp_connections
was used in the NAT for tracking a sccp_connection. Rename it so it is
obvious that the struct belongs to the nat.
The rename was done with sed:
$ sed -i s,"struct sccp_connections","struct nat_sccp_connection",g \
include/openbsc/*.h src/osmo-bsc_nat/* tests/*/*
Prepend the international number with a '+' and then do the normal
re-writing on it. There are a couple of ways to handle this:
\+([0-9]), \+[0-9][0-9]([0-9]), \+49([0-9])
Add a test case for the international re-write based on an already
internationalized number.
We want to send a TRAP with the MGCP statistics from the NAT and
the connected BSC. The BSC endpoint can be either released because
of a DLCX from the MGCP CallAgent or the SCCP Connection release on
the A-link.
This is why we need to queue the statistics when the deleting the
endpoint on the BSC. The processing is continued once the response
arrives. This code assumes that the response of the DLCX will be sent
by the remote side. The current amount of outstanding responses can be
seen on the VTY. This assumption is based on the fact that the BSC has
already responded to the CRCX and maybe to the MDCX.
The MGCP RFC is bended to prefix the transaction identifier with "nat-"
to easily detect the response and hand it to the handler. This will
then parse the response and generate the TRAP. The current version is
v1. We assume that the transaction space is big enough and we will
not re-assign the transaction identifier too early.
In preparation for another kind of black-list allow the filter code
to decide how the connection should be rejected. Introduce a new struct
that will carry the reject causes for certain operations.
This file is created in ./configure so we shouldn't remove it with make.
Otherwise ./configure && make clean && make check fails with:
make[3]: *** No rule to make target `atconfig', needed by `check-local'.
Stop.
We parse the load_config, take the ptrdiff_t from start and load_config
and from the previous array as the alignment can differ on different ABIs.
This was found by Daniel when executing the tests on a 64 bit userspace.
MGCP is used over UDP and a response might be lost. The MGCP RFC
asks for keeping a list of responses and then using the previous
response to answer a duplicate request. I tried to conserve memory
and just wanted to remember the last transaction identifier and
result-code and re-generate the result from that. This made the
code look bad and this is why the entire response will now be stored.
It sadly increases the memory usage but can not be avoided at this
time.
Remove the msg->l3h pointer for the RQNT callback as strtok has
modified the content of it.
Calculate the expected packages and packet loss as of RFC 3550.
The values should be clamped but our packet loss counter is 32
bits and not 24 and we should clamp at other values but I am
waiting for some issues first before dealing with that.
I saw the old copy of the "Appendix J" code too late and I have
discovered some quirks and I am more familar with my implementation.
Most noticable 'w' only needs to be as big as the input arfcn but
requires the 'w' to be initialized. The power_of_2 implementation
differs as well (mine matches the output of wirehsark).
The f0 could be chosen in a better way but right now picking
the lower bound is the easiest. It is not clear if to use
modulo if the range is chosen in the middle. This can be improved
in the future. Right now I have no bit fiddling for range128, 256
and 1024 as I was running out of time.
Instead of building complex manual byte-wise parsers, we simply use two
strtok_r loops: one iterating over all the lines, the next one
iterating over the invididual space-separated elements in the first line.
The benefit is that we now accept \r, \n or \r\n, or any multiple of
them as line ending. This works around incompliant MGCP implementations
like that of Zynetix MSC.
Addition: mgcp_analyze_header returns 0 when all out parameters have
been set.
Signed-off-by: Holger Hans Peter Freyther <zecke@selfish.org>
Introduce number rewriting of SMS-SUBMIT. Introduce a new list,
move code around to help with finding a new number, somehow the
number encoding for TP-DA is borked, 03.40 references 04.11 but
the length appears to be strlen(number) without taken the type
field into account.
gsm_data_shared.h includes e1_input.h of libosmo-abis, add the
LIBOSMOABIS_CFLAGS to Makefile.am, remove AM_LDFLAGS at the same
time as we only build .a archives.
Match IMSI and destination address against a set of entries, if it
is matching the header will be modified and no sender report will be
requested. Change the test case to request the sender report and then
verify that this bit is reset to 0.
GSM 04.64 8.4.2 asks to ignore UI frames if the DLCI is not known,
or if the "(V(UR)- 32) <= N(U) < V(UR)". E.g. if we want to have
V(UR) == 511 and this frame is dropped, we would ignore N(U)'s
0 to 510. Calculate the delta.
The code is based on Jonathan Santos's "LLC UI window" fix but the
issue was discovered independly.
Alexander Huemer
Holger Hans Peter Freyther
Harald Welte