a3b46c9ac0
mgcp: Fix the signature of the change_cb to not carry the port.
2010-08-05 07:09:14 +08:00
e602cd6988
mgcp: Separate recv from net/bts and remove autodetection
...
This allows a more strict check on the source of RTP messages
and we can more easily reject those. For the BTS without an ip
address we will also update the ip address.
2010-08-05 06:57:29 +08:00
1fc432984c
mgcp: Move the loopback code into the common send as well.
2010-08-05 06:57:29 +08:00
b615164d75
mgcp: Remove the receive code into a new method.
2010-08-05 06:57:29 +08:00
84e1c47f74
mgcp: Move the selection of the right source port to a new method
2010-08-05 06:57:28 +08:00
314584ab44
mgcp: Allocate a different port for the networking...
...
Use the right source port when sending the message.
2010-08-05 06:12:02 +08:00
196349dda1
mgcp: Rename the base port to bts_base as it will be used for the bts
2010-08-05 06:10:58 +08:00
c49212778f
mgcp: Move the bfd for rtp/rtcp into the port
...
Stop using the memset in the mgcp_rtp_end_reset as we
will reset the list pointers and then have a mess..
2010-08-05 06:10:58 +08:00
217d712012
mgcp: Rename the bind method to show it is only binding for the bts port
2010-08-05 06:10:57 +08:00
f1a168dc20
mgcp: Only use early bind for the BTS socket.
...
Simplify the code by onlt allowing one way to allocate
a socket.
2010-08-05 06:10:57 +08:00
58ff219c85
mgcp: Attempt to separate the RTP/RTCP port for the Network and for the BTS
...
We plan to have two different ports for the network and for the
BTS to avoid detecting the BTS and to dynamically allocate the
port to have old data not go to a new socket.
2010-08-05 06:10:57 +08:00
a17d701a70
mgcp: Group the state for bts/net into a struct and have two instances
...
Group the data that each end (network/bts) have into a struct and use
this struct throughout the sourcecode.
2010-08-05 06:10:54 +08:00
8b5772ebe4
mgcp: Remove the forwarding mode as it was not used.
2010-08-05 06:10:13 +08:00
7f8aec2b2b
mgcp: Fix the payload_type... it broke in 7cdc62c012
2010-08-05 06:10:10 +08:00
e66cac359e
nat: Fix the spelling of that comment.
2010-08-05 06:04:13 +08:00
7cdc62c012
mgcp: Fix the reversed net/bts... which has not cause any issue..
2010-08-04 22:21:40 +08:00
c02f11a04f
mgcp: Pass the whole endpoint to the patch method.
2010-08-04 22:20:34 +08:00
f1f6bba16d
mgcp: Fix the order of the arguments...
2010-08-04 22:14:46 +08:00
aaf8301a19
mgcp: Print the conn mode as well
2010-08-04 21:52:11 +08:00
bb14e62a7f
mgcp: Disable the actual patching... this is a temporary hack
2010-08-04 21:52:11 +08:00
2f10458831
mgcp: Print the system for the duplicate SSRC...
2010-08-04 21:52:11 +08:00
Harald Welte
6526ca720c
ipaccess-config / NWL: Decode + print neighbor cell ARFCNs
2010-08-04 13:14:34 +02:00
cbfd09843a
nat: Show if we are connected to the MSC.
2010-08-04 02:34:10 +08:00
a99c5b9d0f
nat: Count the number of connects to the MSC.
2010-08-04 02:31:55 +08:00
03a0ad08cf
nat: Indent the connected... to make it belong to the BSC group
2010-08-04 02:29:03 +08:00
62abaded39
bsc_msc: Fix the naming of this function.
2010-08-04 02:27:34 +08:00
5c1e6cf5fc
mgcp: Only patch the header if we had a change in SSRC
2010-08-03 23:57:16 +08:00
89976e8285
mgcp: Style issue... add a space.
2010-08-03 23:57:16 +08:00
6aa882b515
mgcp: Allow switching the audio streams, patch the header
...
Patch the sequence number, the SSRC and the timestamp to
allow to mix various voice streams, e.g. toggling the loop
during the call.
2010-08-03 23:57:16 +08:00
3186892771
mgcp: Move the rtp state into a struct
...
Use a struct to group the rtp state for the up and the down
link of the bts.
2010-08-03 23:57:16 +08:00
ebc824cd2e
mgcp: Fix the documentation entry for the parameters
2010-08-03 23:57:16 +08:00
Harald Welte
d5db12c160
Use new include paths of libosmo-sccp 0.0.2
2010-08-03 15:11:51 +02:00
c597a4eba1
mgcp: Allow to change the receive (the loopback part) via the VTY
2010-08-03 03:04:31 +08:00
98a3877e97
mgcp: Implement the "loopback" mode for a connection endpoint.
2010-08-03 02:27:21 +08:00
c2b31ed9cd
nat: Fix compilation with nat not being enabled.
...
common_vty.c was including bsc_nat.h which tried to
get the sccp/sccp_types.h which is not required to be
installed. Move all structs using/embedding SCCP structures
into the bsc_nat_sccp.h and include. This should fix
the compilation.
2010-07-31 05:20:31 +08:00
5654c5b090
vty: Handle end for NAT and BSC NAT.
2010-07-31 05:20:31 +08:00
Harald Welte
a780a3dc9f
network-listen: The BSIC flag is not set as expected
2010-07-30 22:35:31 +02:00
Harald Welte
e1d1f45034
ipaccess-config: Don't dump the Rxlevel statistics
2010-07-30 22:35:31 +02:00
Harald Welte
59509630df
ipaccess-config: Terminate program after running BCCH INFO test
2010-07-30 22:35:30 +02:00
Harald Welte
1e194a304f
network_listen: dump BSIC as part of BCCH INFO test
2010-07-30 22:35:30 +02:00
Harald Welte
1ef7ce4fe8
ipaccess-config: Add option to disable color in log output
2010-07-30 22:35:30 +02:00
4b85a32360
chan_alloc: Change Channel Release to release SAPIs, then the channel
...
Currently every SAPI release indication will trigger the channel. It
was possible that we had SAPI=3 and SAPI=0 allocated and we tried to
release the channel by sending a RF Channel Release, the BTS answered
with a RF Channel Release ACK but also sent the SAPI Release Indication
which triggered a channel release here. So it was possible that we
would have released a newly allocated channel because of the SAPI
release of the old connection.
This code now works by releasing all SAPIs from highest to lowest,
then sending a SACH Deactivate and finally releasing the channel. This
approach is in use on the on-waves/bsc-master.
2010-07-31 04:09:38 +08:00
aeb45f5186
chan_alloc: After freeing set the pointer to NULL.
2010-07-31 04:09:38 +08:00
30e1ae923d
sccp: Use the external libosmo-sccp as sccp implementation
...
Add --enable-nat and --enable-osmo-bsc to build applications
requiring the Osmo SCCP library to be installed. We are not
using autodiscover as this is out of fashion.
2010-07-31 04:09:38 +08:00
c44db4a534
abis_rsl: Reduce level from notice to debug for measurement reports
...
It can happen that OpenBSC decides to close the lchan but we
still receive some measurement reports until the BTS has decided
to close the channel.
2010-07-31 04:09:38 +08:00
Harald Welte
290aaed6e4
[BSC] use correct 0x2B padding for user-specified SI
2010-07-30 11:53:18 +02:00
Harald Welte
9fbff4adac
[BSC] Add support for configfile-hardcoded System Information messages
2010-07-30 11:50:09 +02:00
Harald Welte
5f827f4ede
Add more RSL <-> Osmo SI type mappings, export osmo_sitype_strs[]
2010-07-30 11:17:13 +02:00
Harald Welte
88f9d98ccc
Use hexparse() from libosmocore >= 0.1.14
2010-07-30 10:39:26 +02:00
417920a660
mgcp: Attempt to count lost packets better...
2010-07-29 03:04:57 +08:00
Holger Hans Peter Freyther
Harald Welte