nat: Catch up with controlif_setup API change
We now save a control handle reference in the nat
osmo-bsc: Catch up with controlif_setup API change
We now save a control handle reference in the gsm network
We now have a lchan->csd_mode member that determines if RSL should
activate the channel in CSD transparent services or not. The previous
code always assumed CSD is non-transparent.
(This requires libosmocore >= eed26116c96f03c6128fac3dead9054714af6cab)
so far, osmo-bts/sysmobts used to be entered as "sysmobts" type in the
configuration file. However, there are some differences in the
protocol/behaviour and we should reflect that by a new BTS plugin (with
lots of code reuse from the nanobts driver).
The ip.access nanoBTS appears to send quite broken NTP timestamps in
the RTCP messages might confuse equipment that uses the sender report
of the BTS. Make it easy to experiment by adding an option to drop RTCP.
We want to have multiple MSCs but we also have some data
that is only present on a per BSC basis. Right now the
MSC data is not allocated with talloc, so we have some
change in the talloc contexts.
Instead of building complex manual byte-wise parsers, we simply use two
strtok_r loops: one iterating over all the lines, the next one
iterating over the invididual space-separated elements in the first line.
The benefit is that we now accept \r, \n or \r\n, or any multiple of
them as line ending. This works around incompliant MGCP implementations
like that of Zynetix MSC.
Addition: mgcp_analyze_header returns 0 when all out parameters have
been set.
Signed-off-by: Holger Hans Peter Freyther <zecke@selfish.org>
Introduce a SS_CCCH for the paging and the rach load. The paging
code could now start using the signal.
GCC warning:
abis_rsl.c: In function ‘rsl_rx_ccch_load’:
abis_rsl.c:1371:11: warning: variable ‘rach_access_count’ set but not used [-Wunused-but-set-variable]
abis_rsl.c:1370:11: warning: variable ‘rach_busy_count’ set but not used [-Wunused-but-set-variable]
abis_rsl.c:1369:11: warning: variable ‘rach_slot_count’ set but not used [-Wunused-but-set-variable]
RR Messages like STATUS, GPRS SUSPEND, HANDOVER COMPLETE/FAIL, ...
should be processed on the BSC side of things, not on the MSC side.
This is among other things required in preparation of intra-BSC
hand-over support in osmo-bsc.
Introduce number rewriting of SMS-SUBMIT. Introduce a new list,
move code around to help with finding a new number, somehow the
number encoding for TP-DA is borked, 03.40 references 04.11 but
the length appears to be strlen(number) without taken the type
field into account.
gsm_data_shared.h includes e1_input.h of libosmo-abis, add the
LIBOSMOABIS_CFLAGS to Makefile.am, remove AM_LDFLAGS at the same
time as we only build .a archives.
Increase the version number and send the sizeof of the gsm_mncc
and the gsm_data_frame structure. Include the offsets of some
members as well to maybe identify ABI problems.
The reason we go through this is that we want to benefit from
the native ABI and don't want to force packed structs.
Match IMSI and destination address against a set of entries, if it
is matching the header will be modified and no sender report will be
requested. Change the test case to request the sender report and then
verify that this bit is reset to 0.
GSM 04.64 8.4.2 asks to ignore UI frames if the DLCI is not known,
or if the "(V(UR)- 32) <= N(U) < V(UR)". E.g. if we want to have
V(UR) == 511 and this frame is dropped, we would ignore N(U)'s
0 to 510. Calculate the delta.
The code is based on Jonathan Santos's "LLC UI window" fix but the
issue was discovered independly.
The UTC offset from the operating system will be used by default to
calculate the NITZ in MM INFO. However, a "timezone" vty command is
added at the BTS level, allowing BTS-specific overrides, e.g. in case
BTSs are distributed accross multiple timezones.
The BSS-side of BSSGP requires quite a number of additional functions
for sending unidirectional messages that a SGSN never sends.
This is a first step into completing the BSSGP implementation and making
it ready to be used from osmo-bts and other BTS-side GPRS
implementations.
Send a hello packet down to the client with the version number
of the MNCC interface. The hello structure might be extended to
include the endianes, size of each structure, etc.
do_reset was not initialized anywhere anymore, so the reset was never
triggered. It's now fixed and we add an option to skip it in the
config so that when in production, you can restart without config
changes quickly.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Using LLGMM-RESET.req, the GMM can request the LLC of the MS to reset
all its parameters, particularly the sequence numbers. We don't yet do
XID RESET retransmissions, and we don't yet generate a LLGMM-RESET.conf
primitive back to GMM.
The libosmo-abis merge broke Ericsson RBS support, as it didn't get the
part right where the per-TRX OML sign_link is determined while
transmitting OM2000 messages.
As a result of this fix, we can remove the 'to_trx_oml' parameter to
_abis_nm_sendmsg(), which is a nice cleanup.
In order to have the MNCC application reliably decide on the codec type,
it needs to know if we are running on a TCH/F or TCH/H. Thus, we pass
lchan_mode as a new parameter to the 'struct gsm_mncc'
Remove the separation of half-rate and full-rate AMR. The used rate
can be found inside the AMR payload. The signalling of what kind of
traffic channel is used can be done with the GSM 08.08 Chosen
Channel IE in the Assignment Complete message.
This way I can use a fixed payload type in the MGCP GateWay but
have a mixed TCH/F and TCH/H config. E.g. use TCH/F FR3 for some
subscribers when connected to MSC A but use AMR5.9 on a TCH/F for
MSC B when all TCH/Hs are gone.
Move the regexp parsing code from the NAT to libcommon as it will
be used by the NAT and BSC code. This also adds the #include <regex.h>
include to gsm_data. This header should be split up.
This is a big patch that ports openBSC over libosmo-abis.
Sorry, the changes that are included here are all dependent
of libosmo-abis, splitting them into smaller pieces would
leave the repository in some intermediate state, which is
not desired.
The main changes are:
- The directory libabis/ has been removed as it now lives in
libosmo-abis.
- new configuration file format for nanoBTS and HSL femto, we
need to define the virtual e1_line and attach it to the OML
link.
- all the existing BTS drivers (nanoBTS, hsl femto, Nokia site,
BS11 and rbs2000) now use the new libosmo-abis framework.
- use r232 input driver available in libosmo-abis for bs11_config.
- use ipa_msg_recv instead of old ipaccess_read_msg function.
- delete definition of gsm_e1_subslot and input_signal_data.
These structures now lives in libosmo-abis.
Most of this patch are deletions of libabis/ which has been
moved to libosmo-abis.
This patch also modifies openBSC to use all the new definitions
available in libosmocore and libosmo-abis. In order to do that,
we have replaced the following:
- DINP, DMI, DMIB and DMUX by their respective DL* correspondences.
- SS_GLOBAL by SS_L_GLOBAL
- SS_INPUT by SS_L_INPUT
- S_GLOBAL_SHUTDOWN by S_L_GLOBAL_SHUTDOWN
- SS_INPUT by SS_L_INPUT
- S_INP_* by S_L_INP_* sub-signals
- E1INP_NODE by L_E1INP_NODE vty node
This patch has been tested with:
- one nanoBTS
- the HSL femto with the examples available under libosmo-abis
- BS11 with both dahdi and misdn drivers.
This patch modifies openBSC code to use msg->dst which stores the
pointer to the signalling link structure instead of the pointer to
the transceiver structure.
This patch prepares the introduction of libosmo-abis.
The timer callback will simply reset the lchan state to NONE in order
to prevent channels getting stuck in 'activation requested' or
'deactivation requested' states.
Scenario: BTS are configured and working, then the BSC stops working
for some reason (crash or administrative stop).
If the BSC comes back to life, LAPD among other things does not know
about the previous existing TEIs. Instead of ignoring these frames,
we notify the driver that we are seeing frames with unknown TEIs, so
it can try to recover, e.g. by resending the SABM message.
The MS Radio Access Capability IE can be _very_ long in some recent
high-end mobile phones, way beyond the old 14-byte limit. We increase
our array to 52 bytes, and make sure not to overflow that buffer.
The idea that MCC and MNC is enough to classify a subscriber
turns out to be wrong. Certain operatos license a number range
of IMSIs to others. When we see a '^' in the MCC field we treat
it as a regexp. The code now turns the MCC/MNC into a regexp
for the IMSI. It is not using extended POSIX regexp to match
the behavior of the access list.
This should not introduce any functional changes, it just re-arranges
some definitions in the header file, and introduces the ROLE_BSC
define that we enable for the BSC-specific fields.
The daemons set up nanoBTS and HSL femto sockets by default, ie. the
three sockets to support these two drivers are open even if we have
no BTS of that kind.
This patch enables on-demand socket creation, ie. we only enable them
if we have one BTS at least that requires it.
I added two new attributes to the gsm_bts object, they are:
* the start() function includes the code that we need to run to start
the BTS. This new function contains the socket creation in the
particular case of nanoBTS and HSL femto.
* the started boolean, which is used to know if we have already
started the BTS, ie. we have already invoked start().
Note that, I have splitted the bts_model_*_init() function into two
functions, the _init() functions that register the BTS driver
and the _start() functions that start BTS driver on-demand.
While I was at it, I added several changes/cleanups to this patch:
* Group all bts_model_*_init() calls into one function bts_init(),
which is called in the initialization path of osmo-nitb and
osmo-bsc.
* Add openbsc/bss.h that contains the declaration of
bsc_bootstrap_network, bsc_shutdown_net and bts_init.
* Add missing e1inp_init() in osmo-bsc.
* Fix missing declaration of hsl_setup in openbsc/e1_input.h
Introduce a paging group that a BSC can refer to and is used
during the LAC lookup. This way paging can be flooded through
the network and just filtered at the last element in the core.
The current code tries to find _one_ bsc for a paging message
and then continues. The new code will try to find multiple BSCs
for each LAC. This is done in preparation of having two BSCs
handle the same LAC. This code right now is O(m*n) but it will
be worse once paging groups are landed.
The code to test the function was reduced to just test the lac
lookup code as the other part can not be tested in a standalone
setup anymore.
The code to create the struct gsm_bts is in libcommon right now
and we can not call paging_init from there. Right now it appears
to be the easiest of doing the init internally.
Be able to configure a list of destinations (duplicates allowed)
that will be tried in a round robin fashion. The change is in
the bsc_msc_connection to operate on a list. We achieve the
round robin nature with the same trick used in the paging code
to delete and append the current entry. The nat code was updated
to compile but one can only configure one destination.
For restarting the NAT we can now block it, it will not accept
new connections and for existing connections it will attempt
to drop them over time. A blocked NAT will end up with no BSC
connections left and then can be safely restarted.
Keep track of the used transaction identifier and always forward
messages to the USSD provider. E.g. this can be used to have a
dialogue going. Right now it is still possible that the MSC will
close down the connection.
* include/openbsc/ipaccess.h: Reserve a protocol number for control
commands
* input/ipaccess.c: New function ipaccess_prepend_header_ext prepends
the extension header
This patch finishes the new ipaccess_send_*() functions and use them
in the ipaccess-proxy code.
I have also cleanup the definition of the PONG, ID_ACK and ID_REQ
messages (including some minor documentation about them).
I had to rename ipaccess_recvmsg() in ipaccess-proxy to avoid clashing
with the one defined in libabis.
For the USSD module we only want to handle requests that are
legitimate. This is achieved by looking for the CM Service Accept
or the BSSAP CIPHER MODE COMMAND.
This patch extends the make_sock() prototype so you can fully set
the fields priv_nr and data of the bsc_fd structure.
This is the first step to get rid of the internal make_sock()
implementation that ipaccess-proxy uses.
This patch includes a minor cleanup to pass INADDR_ANY instead
of zero, if you do not want to bind the socket to one specific
address.
libosmogsm is a new library that is distributed in the libosmocore.
Now, openbsc depends on it. This patch gets openbsc with this
change.
This patch also rewrites all include path to the new
osmocom/[gsm|core]
Signed-off-by: Pablo Neira Ayuso <pablo@gnumonks.org>
This change is required to finish the integration of the VTY and
the per-application logging categories that provides:
"vty: integration with logging framework"
in libosmocore.
It has been tested with osmo-nitb. The other just compiled tested.
Daniel Willmann
Harald Welte
Sylvain Munaut
Alexander Huemer
Dieter Spaar