Move to the control command handling out of the main file into
a dedicated module. There are still some calls embedded into the
main code but it will be moved soon.
Use a usec timestamp for the local time. The seconds to usec will
swap over to the lower bits but this appears to be correct. The
CLOCK_MONOTONIC is used to fulfill the RFC 3550 requirement even
if it is a bit slower than the gettimeofday.
Make sure to initialize transit in a way that the first transit
time will be 0. Otherwise the jitter will contain the difference
of the localtime and the remote time.
Calculate the expected packages and packet loss as of RFC 3550.
The values should be clamped but our packet loss counter is 32
bits and not 24 and we should clamp at other values but I am
waiting for some issues first before dealing with that.
This is missing the probation and the dealing with a remote
restart. For the remote restart we will simply write a log
statement as this is unlikely to happen during a call or if
it does happen the call will be taken down by the BSC anyway.
Align the naming inside the mgcp_rtp_state with the naming inside
the 'source' struct of the appendix. Make first_seq_no/base_seq
a uint16_t. This is removing rules for alignments and reduces the
struct from 40 bytes to 36.
Count the received octets. This is encouraged by the MGCP specification.
Use a 32bit counter that is good enough for more than 12 hours of a EFR
call. This limit is good enough for the current configuration.
The RFC 3435 specifies a different formula for calculating the lost
packages. It involves the number of received packages and the delta
of the sequence number.
The previous code didn't work as expected. The trx and dst pointer
are located in an union and in the case of the Abis code the dst
is used to point to the signalling link timeslot and not the TRX.
The is_ipaccess_bts always returned false because the dst was casted
to a trx while it was no trx.
This fix was tested with the nack_test/NACKTest.st of the test repo.
The test cases were failing on 64bit systems because the sizeof
code operated on the pointer size which is 8 and longer than the
size that was intended to be used for comparing it.
It is a bad idea to detach a subscriber. The subscriber will not
be reachable until the next periodic updating cycle. In case we have
too many failed deliveries we will need to reduce the period for the
LU and implement a subscriber purging task.
This is a preparation for the 29C3 and a problem Jolly experience with
his type writer system.
I saw the old copy of the "Appendix J" code too late and I have
discovered some quirks and I am more familar with my implementation.
Most noticable 'w' only needs to be as big as the input arfcn but
requires the 'w' to be initialized. The power_of_2 implementation
differs as well (mine matches the output of wirehsark).
The f0 could be chosen in a better way but right now picking
the lower bound is the easiest. It is not clear if to use
modulo if the range is chosen in the middle. This can be improved
in the future. Right now I have no bit fiddling for range128, 256
and 1024 as I was running out of time.
alpha=0 (the new value) doesn't reduce MS transmission power during GPRS
as much as we did with alpha=10. This is to optimize for coverage and
to keep GPRS working at all cost, and not care about MS battery life
time or uplink interference in surrounding cells.
FIXME: This should be made configurable via the VTY and the normal
default (unless configured otherwise by vty/config file) should be '6'.
In order to keep mobile at PACCH as long as possible the timer T3192 is
set to 1500ms. This reduces the probablity of long lasting assignment
process on CCCH for subsequent downlink TBFs.
Inspect the message and see if it is a paging response,
then try to find the MSC that has paged this subscriber
and select this as the target MSC, also move the MSC to
the back of the list for 'load balancing'.
The lines 461 and 303 were producing unaligned memory access as
the BVCI was not aligned properly. Introduce a tlvp_val16_unal to
read 16bit from the data, use memcpy to the stack to make sure
that it is working in the aligned and unaligned case.