subscr_name() was called from several places:
* either without a check for subscr being NULL, which for example
was causing a segfault if we hand-over a channel before identifying the
subscriber
* or with an explicit NULL check and the ternary operator (?).
We now simplify the code by checking for the NULL Subscriber in subscr_name()
itself.
Change-Id: Ide09f4a515222eb2ec6c25e7a6a8c5f6cc2ffd4b
Reviewed-on: https://gerrit.osmocom.org/92
Tested-by: Jenkins Builder
Reviewed-by: Holger Freyther <holger@freyther.de>
Drop unused linking of libmsc, and drop duplicate linking of libbsc.
Change-Id: If2d63adb832c72ff1a22c25a78e06b0c244628d2
Reviewed-on: https://gerrit.osmocom.org/88
Tested-by: Jenkins Builder
Reviewed-by: Holger Freyther <holger@freyther.de>
Previously *FULL measurements were always used for handover
decisions. Those are incorrect in case of DTX - check if it was enabled
and use *SUB instead.
Note: *SUB values have higher variance so there might be more "bad"
values compared to *FULL although real quality remains the same.
Change-Id: I95e8e544047a83a256e057a47458678f40a19a15
Related: OS#1701
Reviewed-on: https://gerrit.osmocom.org/66
Tested-by: Jenkins Builder
Reviewed-by: Harald Welte <laforge@gnumonks.org>
* Add per-BTS DTX settings
* Configure Uplink and Downlink DTX separately
* Deprecate global DTX option (it was never tested/used anyway)
* Use libosmocore function for DTX indicator in System
Information (previously it was incorrectly assigned for half-rate
channels)
Related: OS#22
Change-Id: I3d55168475ad47044b6238b55846ea22bdd518a4
Reviewed-on: https://gerrit.osmocom.org/40
Tested-by: Jenkins Builder
Reviewed-by: Holger Freyther <holger@freyther.de>
Move copy-pasted code into separate function to make writing more tests
easier.
Related: OS#1658
Change-Id: I9e39af85718514dd0f081d41c234c9dda77c4b27
Reviewed-on: https://gerrit.osmocom.org/43
Tested-by: Jenkins Builder
Reviewed-by: Holger Freyther <holger@freyther.de>
In the past, normal migration was possible only if the actual
schema version differed from the version used in DB by 1. For
example, if DB uses an old version 3 and you need to use it
with the code written for version 5, the check_db_revision()
will convert it to 4 and DB will still use incompatible schema
version during Osmo-NITB running time. After next run it will
be converted to version 5.
This patch replaces a set of 'else-if' checks by a 'switch'
without 'break' statements between 'case' labels (waterfall).
It makes you able to migrate from current version to the
latest despite any difference between them.
Change-Id: Ia9c2aa86f96b88ad8a710d0a23879ce219bc82dc
Reviewed-on: https://gerrit.osmocom.org/62
Tested-by: Jenkins Builder
Reviewed-by: Holger Freyther <holger@freyther.de>
In commit 4adb136da6 we introduced
a new authentication state SGSN_AUTH_AUTHENTICATE, but we didn't
add that to auth_state_names[] resulting in log messages printing
it abut 'unknown 0x1' rather than something more useful.
The existing GSUP code expected the subscriber data to be piggy-backed
onto the location update response, rather than a separate (and nested)
insert subscriber data request/response phase.
With this patch we should now support both the nested as well as the
piggy-backed version.
In general, if a function generates output data like a msgb (or in this
case filling an osmo_oap_message structure), the output argument
precedes the source. This is what we use all over libosmo*, and it is
modelled after memcpy(), where dst is the first argument, before src.
Let's align osmo_oap_decode(). Intestingly, osmo_oap_encode was already
correct, so the encode/decode functions used different conventions
before.
This rename is the first step of moving the associated functions into
libosmocore.
Also, rename gprs_match_* to osmo_match_shift_* to indicate that it is
not just matching the TLV, but also shifting the data portion.
This is a preparation to move the related code to libosmocore, whilst
at the same time generalizing it from GPRS Subscriber Update Protocol
to the Osmocom Generic Subscriber Update Protoco.
Rather than having a 'private' structure for kc, sres and rand, we
now finally (with 4 years delay) use osmo_auth_vector from libosmogsm,
which encapsulates authentication vectors that can be either GSM
triplets or UMTS quintuples or a combination of both.
gsm_auth_tuple becomes a wrapper around osmo_auth_vector, adding
use_count and key_seq to it.
key_seq is no longer initialized inside gprs_gsup_messages.c, as there
is no CKSN / key_seq inside the message anyway. If a usre of the code
needs key_seq, they need to manage it themselves.
In case both TCH/H and TCH/F or different codecs are configured and
internal MNCC handler is used we might end up in a situation where call
legs with incompatible channel types or codecs would be connected
resulting in a broken audio. Disconnect such calls with appropriate
error message.
Fixes: OS#1663
This adds a very basic, use once example in python on how to connect
and deal with the app specific payload and messages. The code is not
complete as the invokeId should be patched according to the initial
invoke. This excercise is left to future readers of that code.
* support for sending arbitrary static SI2quater.
* vty interface for neightbor EARFCNs specific to SI2quater.
* dynamic generation of SI2quater messages.
* unit test for SI2quater messages.
Fixes: OS#1630
Move define to header file.
Use inline functions where appropriate.
Change int variables which are used as boolean into actual bool to make
code easier to follow.
Use the simpler approach and just call encode('hex') on the str and
then convert it to lower case to keep the tests working.
reproduce:
Python 2.6.6 (r266:84292, Dec 27 2010, 00:02:40)
[GCC 4.4.5] on linux2
Type "help", "copyright", "credits" or "license" for more information.
>>> d = '\0\0'
>>> d
'\x00\x00'
>>> "".join("{:02x}".format(ord(c)) for c in d)
Traceback (most recent call last):
File "<stdin>", line 1, in <module>
File "<stdin>", line 1, in <genexpr>
ValueError: zero length field name in format
fixes:
======================================================================
ERROR: testBSCreload (__main__.TestVTYNAT)
----------------------------------------------------------------------
Traceback (most recent call last):
File "./vty_test_runner.py", line 658, in testBSCreload
b0 = nat_bsc_sock_test(0, "lol")
File "./vty_test_runner.py", line 1150, in nat_bsc_sock_test
ipa_handle_small(bsc, verbose)
File "./vty_test_runner.py", line 1116, in ipa_handle_small
s = data2str(x.recv(4))
File "./vty_test_runner.py", line 1100, in data2str
return "".join("{:02x}".format(ord(c)) for c in d)
File "./vty_test_runner.py", line 1100, in <genexpr>
return "".join("{:02x}".format(ord(c)) for c in d)
ValueError: zero length field name in format
----------------------------------------------------------------------
If we want to separate the BSCs we should separate based on
the source port and not the source ip (at least in the current
test setup).
Fixes:
======================================================================
ERROR: testBSCreload (__main__.TestVTYNAT)
----------------------------------------------------------------------
Traceback (most recent call last):
File "./vty_test_runner.py", line 658, in testBSCreload
b0 = nat_bsc_sock_test(0, "lol")
File "./vty_test_runner.py", line 1145, in nat_bsc_sock_test
bsc.bind(('127.0.0.1' + str(nr), 0))
File "<string>", line 1, in bind
error: [Errno 99] Cannot assign requested address
----------------------------------------------------------------------
Update the comment to reflect that the NAT itself will bind to port
5000 and then the mock MSC will fail to bind to it. Try to move the
mock MSC to another port.
Could fix:
======================================================================
ERROR: testBSCreload (__main__.TestVTYNAT)
----------------------------------------------------------------------
Traceback (most recent call last):
File "./vty_test_runner.py", line 654, in testBSCreload
msc = nat_msc_test(self, ip)
File "./vty_test_runner.py", line 1101, in nat_msc_test
msc.bind((ip, 5000))
File "<string>", line 1, in bind
error: [Errno 98] Address already in use
----------------------------------------------------------------------
Don't assume that one can just bind to a local address that has
not been configured. Remove the unspecific comment as I don't know
to which other tests it is referred to.
This should fix:
======================================================================
ERROR: testBSCreload (__main__.TestVTYNAT)
----------------------------------------------------------------------
Traceback (most recent call last):
File "./vty_test_runner.py", line 655, in testBSCreload
msc = nat_msc_test(self, ip)
File "./vty_test_runner.py", line 1102, in nat_msc_test
msc.bind((ip, 5000))
File "<string>", line 1, in bind
error: [Errno 99] Cannot assign requested address
----------------------------------------------------------------------
Add vty tests for BSC configuration reloading.
Load BSCs configuration on bscs-config-file command:
* remove all runtime configured BSC not in the config file
* close connections to all BSC with updated token value
Fixes: OS#1670
Sponsored-by: On-Waves ehf
Introduce new configuration option bscs-config-file which includes BSC
configuration from the given file. Both absolute and relative (to the
main config file) paths are supported.
Add 'show bscs-config' command to display current BSC configuration.
Note: it is still possible to have BSC configuration in the main
file (provided proper index number is used) and in runtime but BSC
configuration is no longer saved automatically. The management of
included configuration file is left to external tools.
Update configuration examples.
Fixes: OS#1669
Sponsored-by: On-Waves ehf
Factor out 2, add 3 functions. Those functions are simple wrappers
around hex strings specific to IPA protocol. Not all of them are
utilized at the moment but they were checked with wireshark while
working on the tests. It might come in handy if we'd like to further
expand related test harness in future. The same goes for optional
verbosity argument which is not used right now but will be handy for
future debugging.
Extend the existing ctrl command to be able to specify the
algorithm and Ki. In contrast to the VTY no size check is
done. Together with the VTY this code only supports a small
part of what is supported by libosmocore.
The algorithm and ki are considered optional but if a valid
algorithm other than "none" is passed, a KI must be passed as
well.
Extend the test coverage by passing the potential values. It
is not verified that the KI/algorithm is stored.
We should not return a subscriber in case it was not written to
the database. Instead free the memory allocated and return NULL.
Callers in gsm_04_08.c are prepared to have the creation fail.
Related: OS Issue #1657
The issue of db_create_subscriber updating an already existing subscr
is that the same subscriber will then have two entries in the active
subscribers list. In general this will break assumptions that a subscr
can be compared by comparing the pointer.
In the case of the VTY this was not an issue as the created subscr
was immediately destroyed again but it is better to avoid this problem.
Change the VTY command to find the subscriber and then call sync to
have the updated time set. The side-effect is we will now have two
queries for the subscriber. Once through subscr_get_by_imsi and once
through db_create_subscriber.
Change the db_create_subscriber to fail if a subscriber already exists,
and add a testcase for this behavior and do not updated the 'updated'
timestamp of an already existing subscriber.
Add a testcase for this behavior.
Related: OS Issue #1657
Add testcase to issue the subscriber create twice. db_create_subscriber
in db.c will first try to find the subscriber and if it exists, it will
update the "updated" column in the database.
Related: OS Issue #1657
The ip.access nanoBTS seems to have severe issues with BSSGP when
changing the country code and/or network code. It is unlikely that
the proprietary code is getting fixed so we extend the parameter
for the apply-configuration command to carry the 'restart' param.
The nanoBTS continues to be buggy and seems to have broken BSSGP
when changing SIs across new OML connections. Add an easy command
to force the reboot of the system through OML.
Make sure a new auth tuple is initialized after
db_get_lastauthtuple_for_subscr() returns an error, i.e. if no tuple is present
for the subscriber yet.
Before this patch, the first key_seq depended on the typically uninitialized
value that was present in auth tuple's key_seq upon calling
auth_get_tuple_for_subscr().
The very first key_seq used for a new subscriber will now always be 0. Before,
it used to be mostly 1 ("(0 + 1) % 7"), but depended on whether the key_seq was
indeed initialized with 0, actually by random.
In auth_get_tuple_for_subscr(), add missing condition to match incoming
key_seq with stored key_seq, so that re-authentication is requested for
mismatching key_seqs.
Add test for this issue.
Instead of using hardcoded -1 for errors, include -1 in the enum auth_action
type; apply its use.
In the mm_auth test, the string output changes from '(internal error)' to
'AUTH_ERROR', since now the proper enum value is used in auth_action_names[].
Test two situations for AUTH_DO_AUTH_THEN_CIPH:
- when no auth tuple is available
- when the key sequence from LU is marked invalid
Add convenience auth tuple comparison function using stringification.
Add basic MM Authentication test setup, with fake DB access and RAND_bytes().
So far implement simple tests for IO error during DB access and missing auth
entry.
To print the auth action during tests, add struct auth_action_names and
auth_action_str() inline function in auth.[hc].
Don't store an MSC index number in the vty->index void* value. Instead,
store the osmo_msc_data struct directly. Thus avoid warnings about
differences in int vs void* sizes, and save some index lookups.
In OpenBSC, we traditionally displayed a TMSI in its integer
representation, which is quite unusual in the telecom world. A TMSI is
normally printed as a series of 8 hex digits.
This patch aligns OpenBSC with the telecom industry standard.
Signed-off-by: Vadim Yanitskiy <axilirator@gmail.com>
mgcp_transcode.c: In function 'decode_audio':
mgcp_transcode.c:332:4: warning: format '%d' expects argument of type 'int', but argument 7 has type 'size_t' [-Wformat=]
LOGP(DMGCP, LOGL_ERROR,
^
mgcp_transcode.c:332:4: warning: format '%d' expects argument of type 'int', but argument 8 has type 'long unsigned int' [-Wformat=]
mgcp_transcode.c: In function 'encode_audio':
mgcp_transcode.c:390:4: warning: format '%d' expects argument of type 'int', but argument 7 has type 'size_t' [-Wformat=]
LOGP(DMGCP, LOGL_INFO,
^
mgcp_transcode.c:390:4: warning: format '%d' expects argument of type 'int', but argument 8 has type 'size_t' [-Wformat=]
mgcp_transcode.c: In function 'mgcp_transcoding_process_rtp':
mgcp_transcode.c:542:5: warning: format '%d' expects argument of type 'int', but argument 9 has type 'size_t' [-Wformat=]
LOGP(DMGCP, LOGL_NOTICE,
^
mgcp_transcode.c:571:4: warning: format '%d' expects argument of type 'int', but argument 7 has type 'size_t' [-Wformat=]
LOGP(DMGCP, LOGL_NOTICE,
^
There is no concurrency involved and if it failed the first time,
it will fail the second, third, ... time as well. Simply print that
we will leak the database instance.
libosmocore recently added inline functions to relieve callers from applying
bitmasks and bit shifts to access the transaction id of a GSM 04.08 header.
Apply these functions.
Replace hardcoded protocol discriminator and message type bitmasks with
function calls recently introduced in libosmocore.
Note that the release 98 bitmasks slightly differ from the release 99 bitmasks.
This patch uses the "default" gsm48_hdr_msg_type invocation, thus it depends on
libosmocore whether 98 or 99 bitmasks are used.
In some places, use of the bitmask was erratic. Fix these implicitly by
employing the bitmask functions:
* silent_call.c: silent_call_reroute(): add missing bitmask for MM.
* bsc_msg_filter.c: bsc_msg_filter_initial(): RR vs. MM messages.
* osmo_bsc_filter.c: bsc_find_msc() and bsc_scan_bts_msg(): RR vs. MM
messages.
* bsc_nat_rewrite.c: bsc_nat_rewrite_msg(): SMS vs. CC messages.
* bsc_ussd.c: no bitmask is applicable for the message types used here.
* gb_proxy.c: gbproxy_imsi_acquisition(): missing bit mask for pdisc.
In gprs_gb_parse.c: gprs_gb_parse_dtap(), add a log notice for unexpected
message types.
Make the SMPP bind address configurable (used to be harcoded as "0.0.0.0").
Add VTY command
smpp
local-tcp A.B.C.D <1-65535>
while keeping the old command 'local-tcp-port <1-65535>'. Both the old and the
new command immediately change the SMPP listening address and port.
Add a LOGL_NOTICE log when the SMPP listening address and/or port change.
However, to be useful, this patch has to go somewhat further: refactor the
initialization procedure, because it was impossible to run the VTY commands
without an already established connection.
The SMPP initialization procedure was weird. It would first open a connection
on the default port, and a subsequent VTY port reconfiguration while reading
the config file would try to re-establish a connection on a different port. If
that failed, smpp would switch back to the default port instead of failing the
program launch as the user would expect. If anything else ran on port 2775,
SMPP would thus refuse to launch despite the config file having a different
port: the first bind would always happen on 0.0.0.0:2775. Change that.
In the VTY commands, merely store address and port if no fd is established yet.
Introduce several SMPP initialization stages:
* allocate struct and initialize pointers,
* then read config file without immediately starting to listen,
* and once the main program is ready, start listening.
After that, the VTY command behaves as before: try to re-establish the old
connection if the newly supplied address and port don't work out. I'm not
actually sure why this switch-back behavior is needed, but fair enough.
In detail, replace the function
smpp_smsc_init()
with the various steps
smpp_smsc_alloc_init() -- prepare struct for VTY commands
smpp_smsc_conf() -- set addr an port only, for reading the config file
smpp_smsc_start() -- establish a first connection, for main()
smpp_smsc_restart() -- switch running connection, for telnet VTY
smpp_smsc_stop() -- tear down connection, used by _start() twice
And replace
smpp_openbsc_init()
smpp_openbsc_set_net()
with
smpp_openbsc_alloc_init()
smpp_openbsc_start()
I'd have picked function names like "_bind"/"_unbind", but in the SMPP protocol
there is also a bind/unbind process, so instead I chose the names "_start",
"_restart" and "_stop".
The smsc struct used to be talloc'd outside of smpp_smsc_init(). Since the smsc
code internally uses talloc anyway and employs the smsc struct as talloc
context, I decided to enforce talloc allocation within smpp_smsc_alloc_init().
Be stricter about osmo_signal_register_handler() return codes.
Add ctrl_vty_init() calls and feed the ctrl_vty_get_bind_addr() return value to
ctrl_interface_setup() in the following programs:
osmo-bsc
osmo-bsc_nat
osmo-nitb
osmo-sgsn
For osmo-sgsn, move the control interface setup invocation below the config
parsing, so that the ctrl_vty_get_bind_addr() can return the configured
address.
Abort upon unknown options and missing option arguments. This came to my
attention while rewiring the -m and -M options: passing -M without argument
would launch nitb with wrong configuration. So, rather exit immediately.
If there are legacy options that should be ignored, they deserve an own 'case:'
in the option switch. There are none that I'm aware of though.
Strictly speaking, the unix domain socket location is not a name but a path.
The MNCC socket is called path, so it is confusing to call the ctrl socket
a 'name'.
Following the 'line vty'/'bind A.B.C.D' command added in libosmocore, use the
configured address to set the telnet bind for the VTY line. It is now possible
to publish the VTY on a specific local interface (including 0.0.0.0 aka "any").
Implement in all of:
osmo-gbproxy
osmo-gtphub
osmo-sgsn
osmo-bsc
osmo-bsc_nat
osmo-bsc_mgcp
osmo-nitb
In some of these main programs, move the telnet initialization below the
configuration parsing.
Historically, this was not a good idea for programs using bsc_init.c (aka
bsc_bootstrap_network()), since they expected a gsm_network struct pointer in
((struct telnet_connection*)vty->priv)->priv, so that telnet had to be either
initialized or replaced by a dummy struct. In the meantime, the gsm_network
struct is not actually looked up in a priv pointer but in the static bsc_vty.c
scope (bsc_gsmnet), so this limitation is mere legacy (even though said legacy
is still there in an "#if 0" chunk).
In the other binaries I have briefly looked at the init sequence dependencies
and found no reason to initialize telnet above the config file parsing. In any
case, I have tested every single one of abovementioned binaries to verify that
they still parse the example config successfully and launch, allowing VTY
connections on the configured address(es). I hope this suffices.
In all of the above, log VTY address and port. LOGL_INFO is disabled by default
in some of the logging scopes, and since it is a single log message right at
program launch, I decided for the slightly more aggressive LOGL_NOTICE.
Remove unused talloc.h from bsc_vty.c.
In bsc_nat.c, use OSMO_CTRL_PORT_BSC_NAT instead of hardcoding port number, and
include ctrl/ports.h for that.
Fix comment typo "COMAMND"
If an MM context cannot be found based on BBSGP info and a RA UPDATE
REQUEST is received, try to find an MM context with an P-TMSI from
which the TLLI could have been derived. This also checks, whether the
routing area matches.
This is similar to the old behaviour removed by the commits
"sgsn: Only look at TLLIs in sgsn_mm_ctx_by_tlli" and
"sgsn: Remove tlli_foreign2local", except that this will only
be done for RA UPDATE REQUESTs now.
Sponsored-by: On-Waves ehf
Currently the MM context is just overwritten by a call to
sgsn_mm_ctx_by_tlli(msgb_tlli(msg), &old_ra_id) even if it
has already been found by using the BSSGP info. With the changes
made to sgsn_mm_ctx_by_tlli this will never find a MM context if
the routing area has changed. If the routing area has not changed,
the mmctx has already been found if it exists.
This commit splits searching for an MM context (if it hasn't been
found already) from checking, whether a found one can really be
used. The actual search is removed, so that the MS will be forced to
restart the attach procedure, which is less efficient but safe.
Sponsored-by: On-Waves ehf
Currently the code also matches the TLLI against LOCAL and FOREIGN
mappings of the P-TMSI, thus eventually finding MM contexts not
consistent with the TLLI (both tlli and tlli_new differ). On
the other hand, tlli_new is not checked at all.
This commit changes the function to only look at mmctx->tlli,
mmctx->tlli_new, and the routing area.
Sponsored-by: On-Waves ehf
The BSSGP cell identifier is used to get the RA for the TLLI lookup.
The send_0408_message function used in the tests does not set this,
so the RA identifier is always 0-0-0-0.
This commit adds a parameters to pass the RAID and adds missing
dummy RAIDs.
Note that the CI can still not be set and thus is always 0.
Sponsored-by: On-Waves ehf
Currently foreign TLLI are sometimes mapped to local TLLI in the
hope that they will match. This seems to sometimes introduce
inconsisties, possibly leading to a failing assertion in
_bssgp_tx_dl_ud.
This mapping should probably reduce the allocation of additional
LLME during routing area changes.
This commit removes tlli_foreign2local.
Sponsored-by: On-Waves ehf
This patch lets the build script for openbsc find the libsmpp34 installation
with the help of pkg-config instead of assuming the header files are in
/usr/include.
In 'show running-config', timeslot appears as a sub-element of rsl, but it is a
direct child of trx. Fix the timeslot section in vty_out by removing one space
of idention.
Adjust various config examples.
Rationale: it's not relevant for function, but confuses human operators. Fixing
it will save the next hacker some time.
Even if fclose fails the stream is inaccessible and the second fclose
might cause memory violation.
Linux manpage says:
Upon successful completion 0 is returned. Otherwise, EOF is returned
and errno is set to indicate the error. In either case any further
access (including another call to fclose()) to the stream results in
undefined behavior.
Fixes: CID#57958
memcpy has both the source and destination marked as non-null and
we were still passing NULL (with a zero size) to it. While this
makes sense it violates the constraints of the function. Add the
check to see if these values are NULL or not.
+db.c:583:2: runtime error: null pointer passed as argument 2, which is declared to never be null
+ #0 0x40d7f7 in get_equipment_by_subscr (/home/builder/jenkins/workspace/Osmocom_Sanitizer/source/openbsc/openbsc/tests/db/db_test+0x40d7f7)
+ #1 0x40f6d2 in db_get_subscriber (/home/builder/jenkins/workspace/Osmocom_Sanitizer/source/openbsc/openbsc/tests/db/db_test+0x40f6d2)
+ #2 0x40bfaa in sms_from_result_v3 (/home/builder/jenkins/workspace/Osmocom_Sanitizer/source/openbsc/openbsc/tests/db/db_test+0x40bfaa)
+ #3 0x40c847 in update_db_revision_3 (/home/builder/jenkins/workspace/Osmocom_Sanitizer/source/openbsc/openbsc/tests/db/db_test+0x40c847)
+ #4 0x40cbc3 in check_db_revision (/home/builder/jenkins/workspace/Osmocom_Sanitizer/source/openbsc/openbsc/tests/db/db_test+0x40cbc3)
+ #5 0x40cf85 in db_prepare (/home/builder/jenkins/workspace/Osmocom_Sanitizer/source/openbsc/openbsc/tests/db/db_test+0x40cf85)
+ #6 0x406f18 in main /home/builder/jenkins/workspace/Osmocom_Sanitizer/source/openbsc/openbsc/tests/db/db_test.c:179
+ #7 0x7fd625638a3f in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x20a3f)
+ #8 0x405598 in _start (/home/builder/jenkins/workspace/Osmocom_Sanitizer/source/openbsc/openbsc/tests/db/db_test+0x405598)
+
+db.c:590:2: runtime error: null pointer passed as argument 2, which is declared to never be null
+ #0 0x40da23 in get_equipment_by_subscr (/home/builder/jenkins/workspace/Osmocom_Sanitizer/source/openbsc/openbsc/tests/db/db_test+0x40da23)
+ #1 0x40f6d2 in db_get_subscriber (/home/builder/jenkins/workspace/Osmocom_Sanitizer/source/openbsc/openbsc/tests/db/db_test+0x40f6d2)
+ #2 0x40bfaa in sms_from_result_v3 (/home/builder/jenkins/workspace/Osmocom_Sanitizer/source/openbsc/openbsc/tests/db/db_test+0x40bfaa)
+ #3 0x40c847 in update_db_revision_3 (/home/builder/jenkins/workspace/Osmocom_Sanitizer/source/openbsc/openbsc/tests/db/db_test+0x40c847)
+ #4 0x40cbc3 in check_db_revision (/home/builder/jenkins/workspace/Osmocom_Sanitizer/source/openbsc/openbsc/tests/db/db_test+0x40cbc3)
+ #5 0x40cf85 in db_prepare (/home/builder/jenkins/workspace/Osmocom_Sanitizer/source/openbsc/openbsc/tests/db/db_test+0x40cf85)
+ #6 0x406f18 in main /home/builder/jenkins/workspace/Osmocom_Sanitizer/source/openbsc/openbsc/tests/db/db_test.c:179
+ #7 0x7fd625638a3f in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x20a3f)
+ #8 0x405598 in _start (/home/builder/jenkins/workspace/Osmocom_Sanitizer/source/openbsc/openbsc/tests/db/db_test+0x405598)
When a MNCC handler wants to issue the MNCC_BRIDGE primitive
overt the MNCC interface, this was not possible so far via the
MNCC socket. This primitive was so far only available from the
internal MNCC handler, more or less by accident I suppose. The reason
for this is in the way the array of two call references had been passed
into mncc_tx_to_cc().
The debug log prints the received/sent bytes in hex. When this data surpasses
the buffer size available for the log string (4096), the log is truncated
and lacks a newline character. Limit the amount of dumped bytes to 1000.
Sponsored-by: On-Waves ehi
Handle peer restart earlier, so that all the tunnels are deleted by the restart
code path, instead of the first one being deleted due to reused TEI. That
caused confusing logging messages.
Also, when receiving Delete confirmations from the peer that didn't restart,
don't complain about unknown peer, but acknowledge and remove the half
invalidated tunnel. This means that the pending delete entry from the restart
code path is not needed / not used, so don't bother to add pending delete
entries upon peer restart.
The test test_peer_restarted_reusing_tei() hits the situation where a tunnel is
removed because of a reused TEI rather than the restart counter. Adjust the
test to expect the "out-of-band" delete request earlier on, and to still see
the half invalidated tunnel around. Enhance the test by adding the delete
response from the peer that didn't restart, and add a final tunnels_are()
verification.
Sponsored-by: On-Waves ehi
Because the sender is known, one unique TEI per tunnel suffices to map the TEIs
that the peers are sending to gtphub, instead of previously 4 (SGSN<->GGSN
interaction on User and Ctrl plane, where each had an own unique TEI).
Also, previously, a tunnel's endpoints should also have been checked against
each other for TEI reuse, not only against the endpoints of other tunnels. This
simplification fixes that problem for free.
Thus simplify TEI reuse detection and improve VTY show readability and
debugging.
Adjust log and VTY output for tunnels.
Adjust tests accordingly.
Suggested-by: Holger Hans Peter Freyther <holger@moiji-mobile.com>
Sponsored-by: On-Waves ehi
Some logging was multiline to ease human reading of debug output. However,
in the VTY output, these newlines lack a CR motion. Split multiline logs into
separate lines.
Also add one missing space.
Sponsored-by: On-Waves ehi
We now store the pre-printed lchan name in lchan->name to avoid having
to call sprintf every time there is a debug statement somewhere,
particularly as most of those debug statements are going to be inactive
most of the time.
Don't route User message back by sequence number, rather test that a
completely unrelated User message is routed back properly.
Sponsored-by: On-Waves ehi
If an SGSN is behind NAT, we cannot rely on the default ports. Specifically,
if a GGSN sends a message, the forwarding to the SGSN should go to whichever
port the SGSN last sent from (whether sequence nr is known or not).
Add sgsn_use_sender config and VTY command, and store the sender instead
of the GSN Address IE and default port if set.
Sponsored-by: On-Waves ehi
Rather than passing a tunnel pointer as function arguments, keep it in the
gtp_packet_desc struct passed around anyway.
Reason: in the next commit (will add sgsn_use_sender), I need the tunnel to be
passed back out to gtphub_handle_buf(), and besides simplifying existing code,
this also makes passing the tunnel back out trivial.
Sponsored-by: On-Waves ehi
During the peer review session with Holger, these things were deemed fixable.
No need to have a static gtp_packet_desc in gtphub_handle_buf.
No need to memcpy, direct assignment does the job.
Remove obsolete comments.
Fix a stray space.
Sponsored-by: On-Waves ehi
If a GSN indicates that it has reset, tear down each known tunnel for that GSN
individually (don't send the GSNs on the other side a different restart
counter, because they represent more than just this GSN).
Sponsored-by: On-Waves ehi
During resolution of the header TEI, also return the tunnel struct that
resolved the TEI, so the Delete PDP Ctx code does not need to look it up
again.
Upon Delete PDP Ctx Request, remember the IEs and that a request was made.
Upon Delete PDP Ctx Response, find the pending delete and remove the
corresponding tunnel, iff the response indicates success.
Add a context deletion to regression tests, rename the test appropriately.
Sponsored-by: On-Waves ehi
gsn_addr_from_str(): return error upon NULL string.
Add some debug logging.
With an empty config, no bind addresses were set, and the address parser
did not check for a NULL pointer, resulting in a segfault.
Sponsored-by: On-Waves ehi
This is a mostly cosmetic change. Instead of separate buffer handling
functions, reduce some code duplication by using a side_idx just like the
plane_idx, with arrays.
Sponsored-by: On-Waves ehi
This could be done way better, discussion is pending/ongoing. It is indeed
quite unlikely that any user will ever hit this situation, so there is no
strong drive to invest effort in a more comprehensive implementation.
Sponsored-by: On-Waves ehi
There's no need to keep two separate number pools when both can be fed
from the same pool. User and Ctrl plane TEIs can technically overlap without
colliding, but it doesn't hurt if they don't overlap, either.
Sponsored-by: On-Waves ehi
Force passing a restart counter, by adding such arg to gtphub_start() (test
suite is not affected by this).
In gtphub_main.c, add -r,--restart-file <path> and next_restart_count() to
maintain the counter file. While at it, tweak the cmdline help to unify the
formatting (mostly commas and a missing line break).
Send gtphub's own restart counter. So far, the sender's restart counter was
copied through, which would break as soon as more than one GSN would talk to
the same peer with differing restart counters.
Also fix the in-mem restart counter data type (one octet, not two).
Sponsored-by: On-Waves ehi
So far, gtphub worked perfectly by only tracking single TEIs ... for probably
most uses. But a Ctrl plane tunnel may have expired despite a still active
corresponding User plane tunnel. The User plane would continue to work
indefinitely, but if any Ctrl messages followed after more than six hours of
Ctrl silence, they would have been dropped due to an expired TEI mapping.
We want to
- combine expiry of a user TEI with its ctrl TEI. (done in this patch)
- upon delete PDP context, remove both user and ctrl TEI mappings. (future)
- when a peer indicates a restart counter bump, invalidate its tunnels.
(future)
To facilitate these, track tunnels, complete with both SGSN's and GGSN's
address, original and replaced TEIs, all for both user and ctrl plane, in a
single struct. A single expiry entry handles the entire tunnel, instead of
previously four separate expiries for each endpoint identifier.
Add the concept of a "side", being either GGSN or SGSN, to index tunnel
endpoint structs, and so on.
Track the originating side in the gtp_packet_desc.
Add header_tei_rx: set_tei() overwrites header_tei, but the originally received
header TEI is still needed to match a Create PDP Context Response up with its
Request (and for logging).
Adjust the test suite to expect tunnel listing strings instead of TEI mappings,
with a bonus of making it a lot easier to grok, and including the IP addresses.
Add regression test for refreshing tunnel expiry upon use.
Note: the current implementation is as slow as can possibly be, iterating all
the tunnels all the time. Optimizations are kept for a future commit, on
purpose.
BTW, the sequence number mapping/unmapping structures remain unchanged.
Sponsored-by: On-Waves ehi
The expiry queues are already used for resolved GGSN addresses, and will
soon enlist tunnel structs. Hence the naming should be more general.
Sponsored-by: On-Waves ehi
Make 100% sure the user adds expiring_items in chronological order by asserting
that a newly added expiry is >= the last expiry in the queue. Add llist_last()
to facilitate.
Sponsored-by: On-Waves ehi
Instead of passing the current time around in function arguments ('now'),
rather store the current time once upon decoding a GTP packet in the
gtp_packet_desc passed around anyway ('p->timestamp').
Sponsored-by: On-Waves ehi
Harald Welte
Neels Hofmeyr
Max
Alexander Huemer