This introduces a new LOGP() macro together with LOGL_* definition to
support multiple log levels (severities) throughout the codebase.
Please note that the actual logging system does not use them yet,
in this patch we simply introduce the new macros at the caller site.
With this commit, we can successfully hand over a channel from one cell to
another cell. We implement asynchronous intra-BSC (but inter-BTS) handover.
Changes:
* introduce new DHO log category
* extend rsl_chan_activate_lchan() with argument for HO reference
* introduce actual minimal handover decision making in handover_decision.c
* various fixes to bsc_handover_start() in handover_logic.c
With ip.access, in case of TCH/H, we have one RTP stream for each half-slot
(lchan), not just one per on-air timeslot. This is quite different from
a classic BTS where the TRAU frames of the two TCH/H channels would be
part of the same 16k sub-slot in a E1 timeslot.
Before this commit, OpenBSC used templates for the SYSTEM INFO
1, 2, 3, 4, 5 and 6 messages. Those templates were patched in
various places to reflect the network config like ARFCN.
Now, we actually generate those SI messages ourselves, using
values from the configuration file, and even calculating neighbor
cell lists.
All bts'es that you have configured in OpenBSC will end up in
the neighbor cell list - which should be more than sufficient for
the current small-single-site networks.
This introduces the signals S_LCHAN_ACTIVATE_{ACK,NACK} and
S_LCAN_HANDOVER_{FAIL,COMPL,DETECT} as well as code that actually issues
those signals. The signals are relevant for a yet-to-be-written handover
control logic.
This patch extends struct gsm_meas_rep into a complete structure containing all
information from both uplink and downlink measurement results/reports.
This is a first step to provide this complete measurement data as a C structure
into a to-be-implemented handover decision algorithm.
Both GSM 04.08 RR and GSM 08.58 RSL need the multirate config
in the channel modify. Place the config in the lchan, change
the gsm48 methods to not take the argument, change the RSL
implementation to make use of it with the right IE.
The other code should use the t(l)v_put routines as well but
were left untouched for now.
IPA is naming these functions CRCX, MDCX, DLCX to follow
the naming of the MediaGatewayControlProtocol. Change the
code to go from BIND to CRCX (create connection) and from
CONNECT to MDCX (modify connection).
Connect indicates that it is only possible to call it once
while it is possible to call it more than once to modify
the audio parmaters and such. So the IPA terminology is
making a bit more sense here (now that we know it).
Keep track of which SAPIs have been established either by the
BTS (from the MS) or by us. This can be used by the on-waves
BSC code to figure out if a new request should be made.
Add code to generate an assignment command for a given lchan. It
is expected that the lchan is modified already and the mode will
be picked up from their. Currently only the mandantory items
are supported.
If we have a dynamic TCH/F / PDCH channel configuration, then
we can either ACTIVATE CHANNEL it for a TCH/F, or we need to send
this vendor-specific PDCH ACTIVATE command to use it as a PDCH.
As opposed to a fixed configuration, this allows an intelligent
BSC channel allocator to use otherwise idle channels as PDCH
as long as no more TCH's are needed.
This just adds the 04.08 and RSL bits for A5, but not the logic
for performing authentication.
The caller would first set lchan->encr and then call
gsm48_send_rr_ciph_mode(lchan), which encapsulates the 04.08
CIPHERING MODE COMMAND into a RSL ENCRYPTION COMMAND and sends it
to the BTS for execution + forwarding.
This fixes the 'only first call works' problem that some of us were
having with the nanoBTS.
(the field just happenned to be 0 == GSM48_CMODE_SIGN after startup)
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
SMS related messages are all sent over SAPI=3. But in addition
to that, we also need to send it over the correct link identifier,
i.e. SACCH or main signalling channel
This is only relevant for TRX1, since TRX0 will always opwerate at constant
power. However, when channels on TRX0 are activated, we should provide
a reasonable BS poewr level.
A caller can call rll_establish(lchan, link_id) and a callback to the GSM RLL
code. He will get called back if the RLL link is established or receives some
error message, or the establishment times out.
We need this for proper SMS implementation, where we need to restablish a SAPI3
RLL link before transmitting the actual CP-DATA messages.
So far, we immediately disable the RF channel without following a proper
RLL RELEASE procedure. This patch changes this.
If we locally terminate the connection, the channel allocator now triggers a
RLL RELEASE REQuest, which is responsed by the MS with a RLL RELEASE CONFirm,
based on which we send the RF CHANnel RELease to the BTS.
If the MS terminates the connection, we receive a RLL RELEASE INDication,
based on which we trigger RF CHANnel RELease to the BTS.
* we only need one piece of code to calculate rsl_ie_chan_mode from
our run-time data structures (gsm_lchan)
* add some more channel modes for TCH/H and data
* use enum's to make the compiler warn us about unhandled enum values
* make sure the caller determines the (signalling,speech,data) mode
Harald Welte
Harald Welte
Sylvain Munaut