* keep track of site_id/bts_id in struct gsm_bts
* dynamically match incoming OML/RSL over TCP connections by BTS Unit ID
* introduce new debug category DINP (separate from DMI for hexdumps)
* remove ia_config() as it is no longer needed
*
* ensure that signalling links / E1 line information is correctly printed
* when bootstrapping RSL or OML, tell us for which BTS it is being doen
* separate bootstrap_bts() out from bootstrap_network()
* statically configure two ip.access BTS, one with unit id's 1800/0/0 and 1801/0/0
Patch by Andreas Eversberg to automatically release
layer2 on exit of the application. Made the naming of
the variables consistent (only release_l2 and not both
release_l2 and l2_release).
Kill mi_set_pcap_fd from the header, introduce e1_set_pcap_fd
and call it from bsc_hack.c. Hook into abis_rsl_sendmsg and
_abis_nm_sendmsg for sending and e1inp_rx_ts for reading. It compiles
and should not cause a regression.
* gsm_util now uses caller-allocated data (rather than callee-allocated)
* correctly parse destination address
* parse (but not transcode) non-default encodings of SMS
* reject SMS to unknown destination number
* resolve target subscriber id and store incoming SMS (without header) in 'sms' table
What we're now missing is the sending part, i.e. a regular task iterating over
all pending SMS and trying to deliver them. Also, check for pending SMS once
we get a LOCATION UPDATE.
* initialize some data structures before using them in RSL
* DATA_REQ is a transparent message
* more elaborate DEBUGP statements here and there
* don't call 04.08 with zero-length RSL DATA INDICATION
* reject 04.08 CC HOLD and RETRIEVE, as we don't support them yet
* correctly lchan_put the second lchan of a call at teardown
* map the RTP streams of ip.access onto each other
* fix bug that prevented a CONNECt message to ever reach the 'B' side
* initiate phone calls from one MS
* look-up the subscriber based on dialled extension
* page the called subscriber
* send the SETUP to the called subscriber, including CLIP/CLIR
* get ALERTING notification back to caller
* relay DISCONNECT from either side to the other
This is still far from being complete, but it at least works for the most common case
* introduce new notion of subsystem in addition to signal number
* no need for bitmasks of 'areas' (aka subsystems)
* pass subsystem/signal_nr/... per argument rather than by data structure
* implement TLV type descriptions for NM
* add operational/administrative/availability state keeping logic to abis_nm
* explicitly print all NACK's in abis_nm
* make sure we produce [not just for BS-11] valid channel attributes
This will be used for generic registration and dispatching
of any kind of event. We will have different areas (like
with the debug interface) and each layer can define their
own struct for the event message... This is not tested yet
Start with a large number of available slots. It is guranteed
that we will - at some point - get a paging load and will properly
update the counter and keep it updated.
channel to another one (simple voice call switching)
* add a way more generic E1 input layer, abstracting out the misdn
low-level interface. This also adds infrastructure for multiple TRX
in one BTS, as well as multiple BTS on one E1 link
* add a E1 subchannel multiplexer for sending multiple 16kbit sub-channels
one one 64kBps E1 channel
* add TRAU IDLE frame generation
* terminate bsc_hack in case there is a E1 / mISDN init error
* introduce 'e1_config.c' file with static configuration of our
E1 setup (which TRX/BTS is configured for which TEI/SAPI/E1). This should
later become a config file rather than a compiled C file.
WARNING: all this compiles but is not tested yet. Expect fix-up committs over
the next hours or so
After auto releasing a channel the next paging request will
not be immediately answered. The hypothesis was that we do
not release the channel properly. Implementing Channel Release
of GSM 04.08 should have fixed it, but it didn't. According
to the wireshark dissectors the message is correct though.
- Add the RR cause values to gsm_04_08.
- Implement the Channel Release message
- Invoke the release channel function before deallocating
the lchan.
There is a 1:1 relationship between gsm_bts and the paging
operation. Move the paging state into the gsm_bts which is
simplfying the code a lot. This was hinted by LaF0rge.
(I'm not happy with the names of the structs)
Harald Welte
Holger Freyther