when they are greater than 0 they are written as config paramter.
if they are -1 they are disbaled and automatic gain calibration is
used.
Change-Id: I473ff3ae679784178574d2f76b612dbf77180490
we've provided only all_log_level so far but sometimes it's needed
to select the level per layer. This patch adds the ability
to do so for the NAS layer in the UE.
Change-Id: Iab2bce65e8af81f6d344849c97952e6441cb2846
srsENB now supports PDCP discard so we set it to a sane value.
Also enable status reporting for UL.
Change-Id: Ib6ad0ff57b95a1f220f87c1ede0f6eacc5fb21ff
we've detected a possible race condition during the Msg3
transmission that caused the thread that sets the Msg3 grant
to be delayed. The PHY worker that executed TTI+2 finished
by that time already and didn't even see the pending UL grant.
This is issue is more likely to happen on loaded system,
for example when running parallel ZMQ jobs. We therefore decided
to reduce the number of parallel PHY workers to 2 so the issue
is circumvented.
Change-Id: Ibdb42a1705d87b6d343201458c8fe397398802bc
we've already incrased the t3413 value in 9c7fd618d2
but realized it may still be too low in some cases.
we set it to 12s now.
Change-Id: I9c3c59c0ff8f539a44b420f8ba31eea016c211ce
This patch enables setting cipher and integrity algorithms
in Amarisoft eNB and srsENB via scenario files. If no
settings are defined following defaults are applied:
- Cipher algorithm: EEA0, EEA2, EEA1
- Integrity algorithm: EIA2, EIA1, EIA0
Example of setting cipher algorithms:
- 4g:srsue-rftype@uhd+srsenb-rftype@uhd+mod-enb-cipher@eea1+mod-enb-cipher@eea0+mod-enb-nprb@6
Change-Id: I595206b7d49016fb6d0aec175c828d9537c53886
this executed the PRACH search in the main thread so
PHY workers and PRACH processing don't diverge in loaded
scenarios
Change-Id: I97eddb5f9ca682251ded1f73093c2d0a49462bd6
we've seen that the default value of 2s might be a bit tight.
the value is network dependent so no real default value exists.
however, 6s seems to be a good compromise.
Change-Id: Icc75ee048c2cc605ab26c4c87a039519998f7e57
since ZMQ runs are not using wall clock anyway, measuring
TTI execution isn't useful, disable it therefore to avoid
misleading warnings.
Change-Id: I5c2cb0abcfce0ee67806f6611356f4d5d180541d
the order of checks needs to go from high to low, i.e. the higher
release feature (e.g. qam256) needs to be checked and set first.
in theory it should also be possible to have a CA-capable UE
that does not support QAM256, but for srsUE we announce both anyway.
Change-Id: I2fa49f0cb5d80db412a811ceeb380359c8ad67a7
this patch fixes some regressions in the Amarisoft UE class,
the config template, etc. that have been undetected bc we never
executed tests with it.
Change-Id: I397e675a4018acf3372a3b7e29fd864703b2b919
* add new UE feature
* enable in srsue.conf.templ
* add new table for maximum rates
* add config scenario to enable SIB option for QAM64
Change-Id: I6ac2c9989a761e91b93d76c2507f55f0140b202d
Due to the integration of DL-QAM256 another table for DL max rates is needed.
Therefore, I added the parameter 'qam256' to the feature list in the resource.cfg.
The patch also enables the correct UE settings in the config file.
Change-Id: I2d34395449cdcfb31db66ea887d9adbee551e757
make sure to insert cell specific TAC, PCI and root seq ind
into cell config and do not depend on cell index for a particular
enb. This causes issues in multi-eNB setups.
Change-Id: I6642128a449a0562dd23f7fa393ff48ae2503006
this patch adds the basic notion of FDD and TDD duplexing modes
to the eNB object. So far we've always assume FDD.
Since only Amarisoft eNB supports TDD, the required config
template changes, etc. are only applied there.
The patch also adds a scenario to enable the default TDD config.
Change-Id: I37216b5bfdf527d221913283b6c41d3c8fd6b500
Otherwise osmo-trx with a B200 seems to be having issues receiving some
data from the MS otherwise, making "sms" test fail. In general LU works
fine, and when MS sends the SMS, CM Service Request+Accept also works
fine, but then the BTS never sees the CP-DATA afterwards probably due to
MS power loop.
Change-Id: I5f7e3d22a142521ab83db81635ded252dabcf111
So far we only support setting cell IDs from same ENB. Support for
handover to other ENB will come later, probably by adding some API to be
called during the test to add own's CellID's to other ENB's config.t
Change-Id: I1780bda130cde0faab15d4032117e0aa2b9c5dbe
pass-through the option so they can be used in templates
just concatenate with rf_dev_args for srsLTE eNB/UE, arguments
parsing will handle them
Change-Id: I3818026c159780f29968888f547163cdf730afad
seperate the root sequence index for each cell a bit more to
avoid detection of a single PRACH in both cells
Change-Id: I5aea1a27939c880944779c282e902465ab513715
this avoids the eNB from releasing the UE too early if the UL channel
stays very bad for a longer time but many PUSCH are scheduled
Change-Id: Ib82616e920eecc70fbded12433e54bd90ae1bcd4
this is the default TAC used in the EPC. A recent EPC patch
will reject the S1 setup request if the TACs don't match
Change-Id: I94fdb96631ce3ae35a1b2a9f90d1101df9161233
we've added the modifier to configure Amarisoft eNB channel
model. This patch enables it for srsENB.
Change-Id: I30e65d0431b2d2792986128287caf8b23a22b2c1
Power ramping features were implemented recently for osmo-bts-trx. We
don't want to enable them because it makes phones take longer (if even
at all) to find the network.
Change-Id: I35e2f560b28eddef886ad3b2f8ffb4ff79be77da
this gives higher UL throughput because less resources are reserved for
SR/CQI. For more users we may have to make the value configurable again.
Change-Id: If6c313a1deafffda26e9effeb807ca71064c46bc
we use the otherwise unused QCI 8 as a slightly modified
version of QCI 7 (default RLC UM) with a PDCP discard
timer set to infinity to avoid dropping PDCP SDUs if
packets arive faster than can be processed in the DL
Change-Id: I06b7b583701f90827fba36564f969b5d58c9b9ad
same as for srsEPC this is also required for Amarisoft MME and eNB to support, i.e. 001/01
Note that the 3 digit MNC isn't covered by this.
Change-Id: I80a84e01ec9530c285634452d7c18c17bdd595ce
srsEPC expect zero-padding MNC/MCC in config file. However,
001 and mcc will end up as 1 in the rendered template.
Therefore, they need to be formatted correctly.
Change-Id: Ie63cd1b15b961e493a6dcbd7e5a4fbabe0bb6f33
Andre Puschmann
Pau Espin