The SS_LCHAN signals now always include the lchan_sig_data. For
the measurement report it will optionally include the measurement
report as well. Attempt to update all handlers of this signal as well
Check the signal and only continue if it is any of the
signals we want to handle. In the case of measurement
reports we would cast some random code to a lchan.
The release might release the lchan we want to send the response
on. Reorder the code to first send the message and then give up
the security operation which might release the lchan.
According to the specs (GSM 04.08 Table 9.9), the only possibility
if neci=1 and this cause is used is "Originating call and TCH/F is
needed"
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
With the old code it was possible that we first saw SMS that
we have already in the queue. In that case we had free slots
available but have not filled them. With his new loop we try
harder to find SMS we can send, it attempts (and should work)
to detect a loop to break the loop before finding SMS to deliver.
Increase the number of SMS we will try to send at a time and
decrease the failures we handle before going to the next item. With
the default timeout we will attempt to page the subscriber for 60
seconds and we can increase the queue speed by going to the next
item faster.
The sms queue will attempt to send one SMS per subscriber
to fill all the available slots. It will handle the case
where paging has not started, timed out or if there was
any kind of other failure. It is also retransmitting SMS
in case of failures.
The SMSqueue will be responsible of sending to the user. It will
do so in a loop and will also try not to overload the BTS. This
means the throughput of SMS will be limited.
This is providing access to the paging result, the sms,
the transaction. This will allow the SMS queue to do
decisions based on the source of the failure.
The signal_data was inconsistent. Sometimes we passed the transaction
and sometimes we passed the sms. Change it to always pass the sms. The
S_SMS_SMMA is a bit special as it does not involve any SMS.
This is creating 1000 subscribers and 30 SMS each. The SMS
itself is badly formatted (not a valid 7bit encoding) but
it should be enough for a stress test.
If a signal handler accesses the database he will still see
the old lac. Make sure he is seeing the new one. Update the
subscriber from the database in case the query failed or other
things have changed.
Start counting the attempts of each paging request and call
the callback with the PAGING_BUSY type when the paging request
timed out but the subscriber was not paged at all. This can
only happen with a huge paging backlog.
In case the system has so many pending paging
Introduce a method that will remove all subscribers that have a
zero use count. This is useful if someone wants to purge subscribers
from memory or wants to disable the everything in RAM feature.
This is implemented by not freeing the subscriber when the
reference count becomes smaller than zero. We hope that this
will save many database accesses during the congres.
As we do not yet use the HLR from the SGSN, we allow all MS to
attach to our GPRS network. However, if this is running in a public
environment, it could cause service interruption to users of commercial
GPRS networks.
Thus, we now check if the first 5 digits of the IMSI match the MCC/MNC
of the cell that they want to register to. Thus, any subscribers with
SIM cards from real operators will no longer be accepted.
LOGL_ERROR will make this message shpw up in everey default log
config. However, as it seems, this is commonly observed in case
a MS still sends a MS STATUS (in respons to the MM INFO) at the
end of a location area update.
It might be best to actually change the channel release procedure
to make sure we can still pass such 'late' data to the MSC until
the time the Layer2 has been completely released.
Holger Hans Peter Freyther
Sylvain Munaut
Harald Welte