This commit doesn't change internal logic of any model, only the API to
be able to return result of connect TS asyncrhonously since some models
(like osmo-bts-trx) require some time to process the result. This way
PDCH ACT/DEACT (N)ACK can be sent once the result of this long process
is known. For instance, nowadays in osmo-bts-trx we PDCH (DE)ACT ACK
before getting the result from SETSLOT on the TRX iface.
With this new API, bts_model_ts_connect doesn't return any value
synchronously. Instead, it is expected to always end up calling
cb_ts_connected with the return code from the TS activation process. 0
is considered a successs, while any other value is considered an error.
Change-Id: Ie073a4397dd2f1a691968d12b15b8b42f1e1b0cf
No need to pass -t num_trx anymore to specify number of TRX to use. It
is calculated based on dynamic allocation from VTY config.
Using parameter -t is flagged as deprecated and is transformed into a
NOOP por backward compatibility.
As a result, TRX now are allocated after the BTS is allocated and
initial config (pre-VTY) is applied.
A new function bts_trx_init() is added, to set default config on each
TRX during allocation and before setting VTY config on it.
A new per BTS model function bts_model_trx_init() is added, to allow
per model specific default configuration of each TRX.
Change-Id: Iab1a754ab12a626759f9f90aa66f87bdce65ac9c
* we have to use modulo 51, not 50
* the check for FACCH/SCH has to be applied to to the fn % 51 result
Change-Id: I540a7eeef3ea3ed7347f0f1b5a5a6fe7ce0ec8bb
The unit test that tests lchan_meas_process_measurement() only inputs
test data to lchan_meas_process_measurement() but it is not checked if
the interval end could be detected or not.
- Add a return code to lchan_meas_process_measurement()
- Ensure that the return code is checked in the unit-test
Change-Id: I9e00ce683e8c44528804f65181dbfed9e85e3aed
Related: OS#2975
The function is_meas_overdue() was introduced to allow
lchan_meas_process_measurement() to detect when the end of a measurement
interval has been missed. Interval ends may be missed when the SACCH
block of the related measurement interval gets lost. This is due to the
fact that the SACCH block is used as a trigger to start the measurement
result computation.
The idea behind is_meas_overdue() was to check the frame number of the
current measurement against the frame number of the previous measurement
in order to see if there was a measurement for SACCH in between or not.
Unfortunately SACCH and TCH Voice data is not necessarly processed in
order by each phy. Depending on the phy there may be a jitter between
the timing of SACCH and TCH Voice. Depending on the phy this jitter may
be enough to mess up the timing so that we see a SACCH block earlier
than expected. So we can not use the current frame number of TCH Voice
measurements to check for missed SACCH blocks.
Change-Id: Idfdbf64c1f965f35c12559b3995e2b746c74ee9e
Related: OS#3502
Related: OS#2975
The parameter bs_ag_blks_res, which is loaded into the BTS via the SI3
setting, defines how many of the CCCH blocks shall be used for AGCH. The
remaining CCCH blocks will then be available as PCH for paging.
Unfortunately there is no unit-test yet that verifies that all of the 8
different settings for bs_ag_blks_res.
- Separate the the decision logic that checks if a given fn is part of
an AGCH into a function to have it available in the unit-test.
- Add a test that checks all possible bs_ag_blks_res settings.
Change-Id: Ib9652f4013a4da3766852f8f03ce9ec5590f6989
Related: OS#1575
The unit-test function test_lchan_meas_process_measurement() does not
tag measurements as SUB. Lets make the test function more realistic by
setting the is_sub flag at the correct positions.
- Add SUB-Measurements in the correct position
- Print log lines when adding measurements for sub, also fix
minor bugs in the log printing.
Change-Id: I25c361b21a406c0017ee586f0492c38f2e737e57
Related: OS#3502
Related: OS#2975
At the moment the measurement calculation of osmo-bts works by
collecting the measurement reports the phy emits during a measurement
interval. Normally one would expect a well defind fixed number here, but
some phys will not emit a measurement report for lost blocks. Also
blocks and their reports may get lost because of cpu overload etc.
The computation that is executed at the end of the measurement interval
computes over all received measurement. This evenutally means that
missing measurements will not taken into account and the result will
look better than it is in reality.
To fix this, the interval must be of a defined size and in cases where
less measurements as expected were collected, the algorithm must assume
they have been received with a 100%BER and take that into account.
However, all RSSI and TA/TOA related computations should continue to
rely on actual measurement data.
- make sure the algorithm works over a fixed interval
- replace missing measurements with 100%BER
- fix and extend unit-tests
Change-Id: Idd30fc07603ad7d042c1fb416e247c3bf7d35c8b
Related: OS#2987
The function is_meas_overdue() does not use is_meas_complete() anymore
and therefore the related log output is wrong. Lets correct this.
Change-Id: I9b7aa2f7a7c75bc3eed0c94b6ef9d17e7e36ce96
Related: OS#2975
The tests TC_meas_res_sign_sdcch4 and TC_meas_res_sign_sdcch8 are
failing mainly because lchan->ts->nr is confused with lchan->nr.
There is also a small problem with one of the formulas that compute
fn_missed_end.
- Add explainatory comment to the lookup tables on what the index
is refering to
- use lchan-nr instead of lchan->ts->nr when dealing with SDCCH/4/8
- simplfy and fix the formula
- increase the testcoverage of the unit tests, give SDCCH/4/8 also
a thorough check.
Change-Id: I5d555a21003943bf720c53f3a611029ba45339a9
Related: OS#2975
The function ts45008_83_is_sub() is an integral part of the measurement
calculation as it automatically tags incoming measurements as SUB
measurements. This is important in the context of DTX. Unfortunately
there is no unit test for this function yet.
- Add unit test for ts45008_83_is_sub()
Change-Id: Ia26774859f4bf31baee075896905079368bddd42
Related: OS#3502
We do not test is_meas_complete() individually yet, but it is an
integral part of the measurement processings since this function decides
where a measurement interval ends.
- Add unit tests that test TCH/F, TCH/H, SDCCH/4 and STDCH/8
Change-Id: I8f89d9e7092cd65ba4d5c5649140692dcc20bdd6
Related: OS#2987
the measurement interval end is detected by using the measurement
indication that is related to the SACCH block as a trigger to start the
computation. If the measurement indication for the SACCH gets lost
because the block could not be received then the processing is not
executed. This may cause wrong results or when it happens condecutively
an overflow of the measurement sample buffer.
- Store the frame number of the last received measurement indication
- Use the stored frame number to check if an interval was crossed when
the next measurement indication is received. If we detect that we
missed the interval, catch up by running the computation and
start the next interval.
Change-Id: I3a86cd8185cc6b94258373fe929f0c2f1cf27cfa
Related: OS#2975
the testcase definitions in meas_test.c that define different test
situations for uplink measurement are quite large. Lets have them in a
separate file so that the code meas_test.c is easier to maintain.
- Move all mtc* and ulm* structs as well as the struct definitions
to meas_testcase.h.
Change-Id: I90139ec535056d2cea6de10e77f435d807ce496e
Related: OS#2987
All code in osmo-bts goes through APIs in libosmotrau (osmo_ortp.h),
hence direct dependency is not needed. Fixes OBS warnings:
dpkg-shlibdeps: warning: package could avoid a useless dependency if debian/osmo-bts-trx/usr/bin/osmo-bts-trx was not linked against libortp.so.9 (it uses none of the library's symbols)
dpkg-shlibdeps: warning: package could avoid a useless dependency if debian/osmo-bts-virtual/usr/bin/osmo-bts-omldummy debian/osmo-bts-virtual/usr/bin/osmo-bts-virtual were not linked against libortp.so.9 (they use none of the library's symbols)
Change-Id: I96a9b5f0678331dcf66c007928866a124d8700de
This patch adds extended processing of the high-resolution TOA256
measurement values. It adds reporting of the following values
for each RSL MEAS REP for uplink measurements:
* minimum TOA256 value during reporting period
* maximum TOA256 value during reporting period
* standard deviation of TOA256 value during reporting period
Change-Id: Iea4a4781481f77c6163d82dcd71a844a5be87bf2
We saw in a recent prod setup a BSC with saturated channels. Further
investigation lead to a AGCH queue of 1000 (previous hard_limit)
messages, most of them being regular IMM ASSIGN (non REJ). Hence, we
also want to get rid of other messages in the AGCH queue (like regular
IMM ASSIGN).
Furthermore, In this scenario, sending IMM ASS REJ is as important as other
messages given than nowadays we support dynamic wait indicatior
(calculated based on chan load), which means if we reach the MS, we can
tell it to wait for a long time to reach us again, which is desirable.
Change-Id: I022b8948da8be13fb8f4bc36e7c9dab11c35fddb
In a prod setup, complete channel saturation at the bsc was detected,
and Immediate Assignments were not being answered by the MS once sent by
the BTS.
Further investigation showed that the BTS was all the time printing
messages like this:
"bts.c:540 AGCH: too many messages in queue, refusing message type 0x3f, length = 1001/10"
So it seems the AGCH queue was becoming incredibly full (1000, hard
limit triggered the log), while acgch_queue.max_length was set to 10.
As a result, most probably the Immediate Assignments being sent to the
MS are super old in time, and the MS doesn't known about them anymore
once they are receivied, so no answer is sent back.
Let's try to avoid that by decreasing the hard limit so we never reach
that big queue_len scenario.
The number 100 is selected from data gatherered in agch_test.c which
prints a table of max_length values based on different setups. Some
values can reach around 80 messages, so let's use a slightly bigger hard
limit.
Related: SYS#2695
Change-Id: I272798c959abec123776d2fa8dad5685ec512fbd
Completely drop bts_log_init(), call osmo_init_logging2() directly instead: all
callers of bts_log_init() passed NULL as category string, so all it ever did
was call osmo_init_logging(). The bts_log_info is already declared in the .h.
Here and there also define a proper talloc root context instead of using NULL.
Change-Id: Ic049f77bef74123b95350bcae182a468e0086b9c
gsm_bts_role_bts was introduced at a time when we still shared
gsm_data_shared.[ch] between BSC and BTS, and where we then subsequently
needed a BTS-private structure. Since that sharing was abandoned quite
some time ago, we can merge gsm_bts_role_bts into gsm_bts and do away
with the bts/btsb dualism in a lot of the code.
Change-Id: I4fdd601ea873d9697f89a748cc77bcf7c978fa3e
Rathert han have 11 direct members of gsm_bts_role_bts, group them
into a sub-struct as ew do for other parts like interference, laod, ...
Change-Id: Iefecf4b70c1b11c650913f2ae3783718ffb8a36c
osmo-bts has a table of pchan/channel mode combinations for every
bts. This table models the codec capabilitys of the BTS hardware.
However, having the speech codec apabilities modeled inside the
BTS feature list would be much more comfortable and since the
feature list is communicated back to the BSC we would get the
codec capabilities inside the BSC domain as well.
- remove the pchan/channel mode tables
- set speech codec variants for each BTS type
- fix bts_supports_cm so that it queries the feature list
Change-Id: I977dc729ba856631245aedf76afd48eac92166f7
When the BSC sends a MODE MODIFY request with an unsupported
codec, the BTS must respond with a negative acknowledge.
Currently the codec parameter is not checked at all, which may
lead into malfunction or crash of the BTS.
- Introduce a mechanism to check the codec/rate against a
table that is set up in the phy specific code.
- Add tables with supported codec/rate combinations for
octphy, sysmobts, and trx.
Change-Id: Id9b222b7ab19ece90591718bc562b3a8c5e02023
Related: SYS#3212
Previouslywe could end-up passing empty '-I' to compilerif corresponding
_INCDIR variable was not defined during the ./configure step. This is
apparently tolerated by gcc but still seems like a wrong thingto
do. Let's fix this by moving -I inside of *_INCDIR.
Change-Id: I80915e5756d1bf64d789cfd5341fdd417ca8eed9
Add missing LIBOSMOABIS_CFLAGS and LIBOSMOTRAU_CFLAGS.
Pair the _LIBS below the _CFLAGS in LDADD above (cosmetic).
Fixes the stow-enabled jenkins builds are currently failing like below:
In file included from ../../include/osmo-bts/gsm_data.h:136:0,
from ../../include/osmo-bts/bts.h:4,
from misc_test.c:23:
../../include/osmo-bts/gsm_data_shared.h:21:35: fatal error: osmocom/abis/e1_input.h: No such file or directory
#include <osmocom/abis/e1_input.h>
Change-Id: I94ea8bad8b410550f72ee6a0408f42f6bd8b6cac
The unittest module meas_test.c contains a lot of unused header
files as the result of a cut and paste error made earlier. Also
the reference to stdio.h is missing.
remove all header file references that are not needed.
add missing header reference to stdio.h
Change-Id: I167be096ed25a86b1114de1ada955822a0b42856
Power control loop test outputs next to nothing which is not very
helpful. Make it more verbose. While at it, also move duplicated code
into static function to make test cases less cluttered.
Change-Id: I0a5e65e23e62442ef8758ecbcf8e7820b4f15d7b
Related: OS#2223
There's nothing sysmobts specific in this test so let's move it into
separate directory and run unconditionally. The test itself is unaltered
except for intro text.
Change-Id: I0d1957cd9cf5497826be095c7a42b7bb4fa10397
Related: OS#2223
* copy-paste gsm_data_shared.* from OpenBSC master
* remove corresponding configure check and option
* remove .deb dependency
Actual refactoring with removal of unnecessary structures/parts, moving
common OpenBSC/OsmoBSC parts into libraries etc. are left for further
patches.
Current patch will make coexistence with *BSC easier and will simplify
our build infrastructure.
Change-Id: I9f004fb5c4c1db29d4792dfd281d388c7063da13
Related: OS#1923
In openbsc.git Change-Id I61c18a7f021fcb1ec00d34a745f4e3ab03416c2d
we changed the gsm_bts_alloc() function signature to include
a second argument (the BTS number). This broke omso-bts, and this
commit is intended to make it build again.
Change-Id: I7ef7654d48c1cfc7e4ecb0b771553ec0740ce2bf
The end of the measurement reporting period is not aligned with the
SACCH block where the results are reported. The tables that are
used to detect the end of the measurement period are therefore
wrong. The frame number of the SACCH block must be used and not the
TDMA frame number (modulo 104) of the measurement reporing interval.
The tables are oriented to the frame number of the first SACCH block,
at the beginning of an interval. However, when a SACCH block is received
it will always contain the result of the recently passed measurement
reporting period.
To match the tables, introduce another lookup table to remap each
SACCH block that ends to the matching beginning block number.
Change-Id: I1eef894e6f15b4449fc8926bebb118624efc7924
After switching to libosmocoding there's no need in low-level bursts
test which is part of libosmocoding anyway.
Change-Id: Icb8caf62ac653a39a7a82f2225e8edeab7f5afb5
SI2quater support as per 3GPP TS 44.018 will require chnages to the way
System Information is stored because it uses 1:n instead of 1:1 mapping
between SI type and generated SI content. This should not affect other
SI types though. To facilitate this transition:
* convert the code to always use GSM_LCHAN_SI helper instead of
accessing buffer directly
* move duplicated code to inline function
* add logging for buffer truncation and corresponding length values
Requires I74e4e3cb86364cec869a1472a41b4a95af0d50dd in OpenBSC.
Change-Id: Ie97be6ead6ce6d2d425fbfac8429bb90afb95acc
Related: RT#8792
In case a system has a high-gain external PA (like a 40dB PA) connected
externally, we cannot simply switch the transceiver to 0 dBm in
trx_init() only to then start the ramping at much lower levels once the
PHJ completes in trx_init_compl_cb(). The result would be a short
0 + 40 dBm spike followed by later ramping. We want to avoid that
spike, particularly its associated inrush current, so let's bring up the
board with smething very conservative like -50 dBm, and then ramp from
there.
Change-Id: I0ad91fce64f65e0213c9fcfde3390ace519055db
Fixes: SYS#3259
Log error when handover RACH is detected on wrong channel: according to
3GPP TS 44.018 it can only be seen on SACCH and DCCH.
Change-Id: Iacbcc8441d6cfbb8f808948a8baddde1ebca488a
Related: OS#1898
According to Table 4 in 3GPP TS 45.003 j=11, b=3 case corresponds to
k=91 and not j=12 as was previously used.
Change-Id: Iad3cf545b2f7e16276466cc37dd7a1e7858467e5
This tests the computations of the tx_power.c code using sysmoBTS 1002,
1020, 1100 and 2050 values, as well as the power ramping code.
Change-Id: I1cc88d4c6edff326e2e67d4f869aa02c9b2b1ac5