Both power_ramp_start() and power_ramp_force() are now small macros
around _power_ramp_start()
The new behavior is:
* ramp down power when stopping bts through Ctrl-C
* the other shutdown causes skip power ramping
This will cause the bts to reconnect faster when the oml link is
dropped and power ramping is enabled.
Change-Id: Ida1d7bbf094958b9142af306dbf84206729a609e
Related: SYS#6237
There is no reason why they should have different initial
states. Keep it consistent with the other MOs.
Change-Id: I9fd744ec79da9fc26d3ebe9857b2b0bbd5fcd1ff
This reverts commit c96d34f828.
Reason for revert: This breaks ramping up power since the power ramp logic still assumes the output is full power.
Change-Id: I47a16a4b3ba02d74473569c0f4350a41fc12a464
For the other shutdown causes power ramping doesn't make sense. Instead
shutdown quickly so we can reconnect faster
Change-Id: I71c46478b8f3b236dba3e959fc75e58c0409517f
Related: SYS#6237
The array of trx in gsm_pcu_if_info_ind can hold trx 8 items. Lets use a
define constant to specify the size of that array.
Change-Id: I5fdd5b9e59865fabd0340650ecb347d52208ebe9
The pointer variable l1sap is only used to determine the size of the
related struct but for nothing else. We can use the struct name in
sizeof also directly and get rid of it.
Change-Id: I93abdce1dec60d53ddceb1fce6e9e7451ba6283a
Before this patch, the free CID with the smallest number was always
selected to be used. This caused more or less the same subset of CIDs to
be used all the time, while the CIDs with bigger numbers were mostly
unused.
Let's distribute the use so that all CIDs are used roughly the same.
This has the advantage, among others, that the same CID will not be
re-used immediatelly after being freed if a new call is established.
It is useful to leave the CIDs unused for some time since the other end
peer may know of the call being tear down with some delay.
Hence if a new call is established immediately after the CID was
released, the same CID would be allocated and passed at the peer, which
would then detect that the old call (in its view still active) would
already make use of that remote CID.
Related: SYS#6161
Change-Id: I72803fb172accbabfc81923572890f8ecb06cefd
The scheduler is now using the lookup tables instead of these
functions. The only part using them is the AMR unit test.
Change-Id: I1a9c80dd12252e7befe9c9bc8e8f7ee8648b5465
The number of NSVCs is fixed but lets not use magic numbers to define
the sizes of the arrays that hold the config values. In osmo-pcu there
is already a define constant, so lets use a define here as well.
Change-Id: If7fa44abb86c18900110d7ee81fe6140c8c4635b
Some osmo-bts varieties have a method to make an immediate change to
TX power from the vty. In osmo-bts-trx there does not seem to be any
way, so lets start the power ramp loop when the parameter
osmotrx tx-attenution is changed on a running TRX.
Change-Id: I1fa5e8130202fb509593db4132863b762b0f40b7
The parameter l3_len in rsl_tx_meas_res() is defined as int, even though
it can't be negative. Lets use unsigned int for l3_len.
Change-Id: I99068a36e74a557000f406154dce32300615086c
We request the length using msgb_l2len() in two locations where whe
cannot be sure that l2h is populated. Lets check this first.
Change-Id: Ie13d0724f183ff240714dcdbd24e5a21b4276bfe
Related: OS#5645
The function lchan_meas_handle_sacch() calls msgb_l3len without checking
if l3h is even populated. Lets add a check to be sure.
Change-Id: Ie5a9fe1ba880e68edb74f5f4ca559ac191330d4f
The PCU may poll the MS requesting an ACKnowledgment message to be
sent in form of four Access Bursts instead of Normal Bursts. The
BTS has no prior knowledge of the Uplink burst type, so a new MTS
value was specified in order to prevent the BTS from trying to
decode Access Bursts as a PDTCH block.
This patch implements parsing of the new MTS value 0b0110.
Signalling RACH.ind to the PCU is to be implemented.
Change-Id: I0fbb63006797e6be386d1f76ed97fff098c036fc
Related: OS#4006, SYS#4794
Checking if (bi->chan != TRXC_RACH) is not enough to detect HANDOVER
ACCESS. Receiving this message is only possible on CS channels.
Change-Id: Ice1674fd4fed8c54d605ff19d568f6e46b4c5783
Lchans which are marked as non-connected have not yet received
information about its remote peer, hence they may not have some fields
available yet. Let's skip them to avoid accessing such fields
(lchan->abis_ip.osmux.in).
Related: SYS#5987
Change-Id: Id53822c4a0486b0090df2db3d185e047d14fc90a
This is actually quite common, since our peer may be sending some osmux
packets to us a while after we have closed the conn on our side,
specially if latency is high in the network (eg satellite links).
Related: SYS#598
Change-Id: I102047685b9b9f4cba43970945f955c4fe9c4c95
This way we have no more access to internal osmux structures.
If those counters are needed in the future they can be counted by
osmo-bts by means of adding rate counters to the caller of
osmux_xfrm_input() and deliver_cb.
Change-Id: Ib952437ea3aa2770c96bddb667491e7675a6a06e
Otherwise some shared variables used by both Osmux and RTP was left set,
like connect_ip and connect_port, and next time the lchan was selected,
those were already configured even if they didn't come in IPAC CRCX.
This is specially bad if the channel was reused to set up an Osmux call,
since the osmux code path relied on those fields being properly reset
until set by IPAC CRCX.
Change-Id: I414bd0bc801451357bb45b89197a95e51b7c97f1
when something fails in osmo-bts during startup and it goes into SHUTDOWN state,
it is desirable to close new RSL links (sockets) which are in progress to connect,
while it waits for a while to complete shutdown (power ramping down, etc.).
This way we don't end up with new interactions and new state against a BSC if we
are shutting down.
The new libosmo-abis API is used since the higher layer struct e1inp_sign_link assigned
to each struct gsm_bts_trx is not provided to the osmo-bts code layer by libosmo-abis API
until the TCP+IPA handshake in the socket becomes fully established (sign_link_up()
callback).
Depends: libosmo-abis.git Ia6418321f3b6f1f7274efd414625a4b10a09a362
Change-Id: I599d074f51f490b43c9a89b105d1823391926947
It's not immediately obvious what numeric values mean for CPU scheduling policy.
Let's document this and add doc reference.
Related: OS#4107
Change-Id: Ib047762a336851e6205d77c83068a99d8a868e8b
Previously osmo-bts created /var/run/osmo-bts.pid which
isn't used by anything and makes it hard to run as non-root
user. Let's get rid of this pre-systemd relic.
Related: OS#4107
Change-Id: I86bcaedbc8cb1297476ad741eaa45585fea3c380
By default systemd will execute service with root directory
(or home directory for user instance) which might result in
attempts to create files in unexpected place. Let's set it
to 'osmocom' subdir of state directory
(/var/lib for system instance) instead.
Related: OS#4821
Change-Id: I4b7bcd441e5da81c4c5267715675041171a1ce1e
This helps understand the origin/purpose of those 2 bytes and
what's contained in them.
Related: SYS#5987
Change-Id: I607fdf6d627242e010fba35be1b9b0ffde820d08
This library will be used soon when adding Osmux support to osmo-bts.
Furthermore, it nice to have it available to make use of other general
interfaces to create connections, primitives, RTP and AMR related
functionalities, etc.
Related: SYS#5987
Change-Id: I49db4de715065c083e1249cbeae6298d6868e229
The PRIM_INFO_MODIFY is sent on receipt of the RSL MODE MODIFY message,
which may optionally contain new ciphering parameters. Before this
patch, osmo-bts-trx would ignore the new parameters and continue using
the old ciphering key/algorithm.
* Modify l1if_set_ciphering() to allow updating ciphering params.
* Call l1if_set_ciphering() when handling PRIM_INFO_MODIFY.
This problem was uncovered by BTS_Tests.TC_rsl_modify_encr, which has
been failing ever since it was introduced [1]. This patch makes it pass.
Change-Id: I2278703b487374c0de4cfc42b22e70aaf6548589
Related: [1] I4cbea499bb6a331d314e6573548a4540945208b5 osmo-ttcn3-hacks.git
Related: OS#3750
It will be used too by osmux code present in another file. This is a
preparation commit to simplify the one adding osmux support.
Change-Id: Ie7fa57bb04db9ad9b03971467e12ee7b8e4c190a
The function is long/complex enough, so having one extra struct in_addr
declared the function top only used in one specific small path to print
the variable is unnecesary.
Let's move it to the conditional path where it is used to print the
ip address.
Change-Id: I4c16bbca6a6779537517b6b196828b47eddaa516
There's no need to maintain a duplicate msgb_queue_flush(), which
returns the amount of freed messages (feature not used at all by the
callers).
Change-Id: I9841e18ca0b7b852130bbb02a510e43a3b3fd93f
The queue_limit_to method iterates the entire list of messages every
time a new message is added. Let's use msgb_{enqueue,dequeue}_count()
APIs to do that in constant time. It is true that since the queue is
limited to 1, there's usually at most 1 item in the queue so it's not a
real problem. However, when we add Osmux in the future, we may need to
tweak the amount of messages which can be in the list, due to Osmux
batching mechansim which may be more bursty sometimes.
In any case, this change doesn't make things worse for sure.
The patch also takes the chance to group the queue_limit_to + enqueue
into one function to avoid having the code spread several times.
Change-Id: I61818a3bb521c27bd21a8b6fa70581d27638ec9b
Daniel Willmann
Alexander Couzens
Philipp Maier
Pau Espin
Harald Welte
Vadim Yanitskiy
Keith Whyte