Instead of calling DEBUGPC() over and over, compose a string using
osmo_strbuf and then log it once.
Rationale:
a) DEBUGPC() is a bad idea for gsmtap_log, because each DEBUGPC()
dispatches a separate gsmtap_log packet, fragmenting the actual log line
in wireshark.
b) DEBUGPC() is a bad idea because it checks the logging categories for
every DEBUGPC() invocation.
c) using a separate function with osmo_strbuf and OTC_SELECT, we can
actually skip the entire string composition in case the DMEAS logging
category is disabled, with a single logging category check.
Change-Id: I4cb607ff43a1cb30408427d99d97c103776b6e69
The RSL BS Power IE in measurement reports is encoded as dB / 2.
Instead of using this coding all over the code, converting to dB and
often printing confusing values in logging etc, store as plain dB.
The conversions should be at the points where a "weird" format is
defined: the RSL encoding needs divided-by-two, so apply it there. The
meas_vis is (now unfortunately) defined as div-two, and so on. But
internally we now just store the plain dB value and calculate with it
without duplicating the wire decoding step everywhere.
Rename to bs_power_db to clarify the unit of the stored value.
Change-Id: I229db1d6bcf532af95aff56b2ad18b5ed9d81616
chan_mode_to_rsl_cmod_spd() may actually return negative on error. To be
able to check for that, handle the returned value as a signed rc before
assigning to the unsigned spd_ind.
Related: SYS#5315 OS#4940 CID#236231
Change-Id: I52e13b24ce67e288ff32dbdaa1c1759089926f5c
lchan->modify.info.ch_mode_rate should remain unchanged, it is the
immutable request data. However, for VAMOS, we will want to
automatically see that the chan_mode is chosen correctly.
As a first step, place a mutable ch_mode_rate copy at
lchan->modify.ch_mode_rate, i.e. not in .modify.info, but in
.modify. Use that everywhere.
This is a non-functional change, preparing for a subsequent patch that
adds handling of VAMOS shadow lchans.
Change-Id: I8a3daac0287f15a59d3688388bb13e55facb2cea
Both VAMOS- and non-VAMOS speech modes should result in indentical voice
handling. So make sure that all chan_modes are converted to non-vamos
before comparing / evaluating in switch statements.
Change-Id: I791e7966b1f8eaa3299a8a46abeb313cf5136e0b
So far we have a couple of macros iterating a specific number of lchans,
depending on dynamic timeslot state etc. With addition of VAMOS lchans,
this would become more complex and bloated.
Instead of separate iteration macros for each situation, only have one
that takes a number of lchans as argument. That allows to more clearly
pick the number of lchans, especially for non-trivial VAMOS scenarios.
Related: SYS#5315 OS#4940
Change-Id: Ib2c6baf73a81ba371143ba5adc912aef6f79238d
Activating / modifying to a VAMOS mode will require picking specific TSC
Set / TSC. It is a bad idea to pick the TSC in each message encoding
function, rather make this choice centrally.
So far we pick the training sequence code to use based on the timeslot
configuration, and this TSC is determined only upon encoding the RSL
messages.
Instead, pick the TSC to use upon the initial lchan activation /
modification request; store this in the request structs and pass through
the activation / modification code paths.
For VAMOS modes, we also need to pick a TSC Set. Do so also upon activ /
modif request. Note that the TSC Set is not yet applied in this patch,
it will be applied in upcoming VAMOS patches.
The activ / modif request may pass -1 for tsc_set and/or tsc to indicate
no specific choice of TSC Set and TSC, resulting in the same behavior as
before this patch.
For example, lchan->activate.info.tsc* may be passed as -1. The exact
choice for tsc_set and tsc is then stored in lchan->activate.tsc*, i.e.
one level up (the .info sub-struct is considered as immutable input
args). The lchan->activate.tsc* are the values actually encoded in RSL
messages. After the ACK, the lchan->activate.tsc* is stored in
lchan->tsc* to indicate the TSC actually in use. Same for modif.
Note that in 3GPP TS 45.002, the TSC Set are numbered 1 to 4, while the
TSC are numbered 0 to 7. On the wire, though, TSC Set is sent as 0 to 3
value. This is a weird discrepancy, odd choice made by the spec authors.
For conformance with the spec wording, I decided to pass the TSC Set
number as a 1-4 ranged value, and only convert it to the 0-3 on-the-wire
format upon message encoding. So log messages and VTY output will
indicate the first TSC Set as "1", but the first TSC as "0", as defined
in 3GPP TS 45.002, even if that is somewhat weird.
Related: SYS#5315 OS#4940
Change-Id: Ic665125255d7354f5499d10dda1dd866ab243d24
Expose the training sequence code used in the RSL Channel Description IE
as an input parameter.
So far the Channel Description IE is always composed with a training
sequence code from gsm_ts_tsc(). For RSL commands enabling VAMOS mode,
specific training sequence codes are required.
So far, all callers still use gsm_ts_tsc(), making this a patch without
any functional change. Upcoming patches will pass specific TSC as
configured for VAMOS instead, in specific places.
Related: SYS#5315 OS#4940
Change-Id: I49503a6f5d25bb3bc9a0505bd79ed1d5c4f50577
Prepare for VAMOS, where there will be secondary "shadow" lchans serving
secondary MS on the same timeslots. For those, RSL messages will need to
reflect a different stream ID aka TEI, via an rsl_link_vamos.
Make sure that every code path that sends an RSL message for a specific
lchan selects the RSL link via the new function rsl_chan_link(). When
VAMOS is implemented, this function can select the proper RSL stream.
Rename gsm_bts_trx.rsl_link to rsl_link_primary. This makes sure I'm not
missing any uses of the RSL link, and clarifies the code.
Related: SYS#5315 OS#4940
Change-Id: Ifbf16bb296e91f151d19e15e39f5c953ad77ff17
Firstly, do not store the encoded AMR length-value bits in gsm_lchan->*
before an activation/modify has actually succeeded.
And secondly, do not store the AMR LV structure in struct gsm_lchan at
all, but only generate the TLV exactly when a message is being composed.
In gsm48_multirate_config(), generate the LV directly to a msgb instead
of a static buffer first. gsm0408_test.c expected output verifies that
the generated LV bytes remain unchanged.
In lchan_mr_config(), introduce a target mr_conf argument, so that Chan
Act and Mode Modify may generate the filtered AMR config to different
locations (lchan->{activate,modify}.mr_conf_filtered).
Only after receiving an ACK for Activate/Modify, set
lchan->current_mr_conf from lchan->{activate,modify}.mr_conf_filtered.
Use the properly scoped lchan->activate.mr_conf_filtered for Chan Act,
lchan->modify.mr_conf_filtered for Mode Modify and
new_lchan->current_mr_conf for Handover Command as appropriate.
Related: SYS#5315 OS#4940 OS#3787 OS#3833
Change-Id: Ie57f9d0e3912632903d9740291225bfd1634ed47
The GSM48_CMODE_DATA_* rates are completely unused in OsmoBSC anyway,
but there is some code in abis_rsl.c checking its value, and if we were
to start using it that is the place where it should be.
Related: SYS#5315 OS#4940 OS#3787 OS#3833
Change-Id: Ie0e065a5dca5f4a31d5d81e3528a539214a74170
I noticed during testing that an lchan used as TCH/F in fact still had
its channel mode set to Signalling -- because on Assignment, the Speech
mode used to be placed in the *previous* lchan and the new lchan was
never updated after the Activ ACK. This is unbearable confusion which I
complained about numerous times, so far mostly for cosmetic reasons. But
implementing re-assignment properly actually requires this to be cleaned
up.
Keep all volatile chan mode settings in lchan->activate.* or
lchan->modify.*, and only update lchan->* members when an ACK has been
received for those settings. So a failed request keeps a sane state.
Make sure that those settings are in fact updated in the proper lchan,
upon an ACK, so that subsequent re-assignment or mode-modify know the
accurate lchan state.
Related are upcoming patches that sort out the AMR multirate
configuration in a similar fashion, see
Iebac2dc26412d877e5364f90d6f2ed7a7952351e
Ia7519d2fa9e7f0b61b222d27d077bde4660c40b9
Ie57f9d0e3912632903d9740291225bfd1634ed47.
Related: SYS#5315 OS#4940 OS#3787 OS#3833
Change-Id: Ie0da36124d73efc28a8809b63d7c96e2167fc412
Soon, there will also be enums with ASSIGNMENT_FOR_* and MODIFY_FOR_*
naming. Add the ACTIVATE_ prefix to the existing enum to clarify.
Change-Id: I12190d4d154a1da6a9ebc9a755ccc2fe382ff188
From 3GPP TS 48.008 sec 3.1.30 "Common ID":
"""
If the SCCP connection is established due to CSFB from E-UTRAN and the MSC supports
return to the last used PLMN after CS fallback, then it should send the COMMON ID message
to the BSS including the Last used E-UTRAN PLMN ID information element if available at
the MSC immediately following the successful SCCP connection setup.
"""
Furthermore, 3GPP TS 48.008 version 16.0.0 Release 16 "3.2.1.21 CLEAR COMMAND",
for field CSFB Indication, states:
"""
NOTE: This information element doesn't serve any useful purpose. MSCs should not send the
information element unless it is required by the recipients (due to the need to interwork
with older versions of the protocol). It is expected that in future versions of the present
document, this information element will be deleted from this message.
"""
Hence, build up the EUTRAN neighbor list based on whether we received
the Last E-UTRAN PLMN ID IE during Common Id. In the future, we should
probably filter the list while populating it based on the received IE.
This change will also allow reusing same mechanism for SRVCC
EUTRAN->GERAN support, where te Last E-UTRAN PLMN ID IE can be found
inside "Old BSS to New BSS information" IE in msg HANDOVER REQUEST.
Related: SYS#5337
Change-Id: I5d290ac55eca5adde1c33396422f4c10b83c03d5
It is observed that a CHANnel ReQuireD with access delay
greater than 63 can be received from the Ericsson RBS.
This results in osmo-bsc sending back a CHANnel ACTIVation with
a Timing Advance IE containing the access delay value.
The RBS NACKs this, leading to a BORKEN Channel.
This patch makes the maximum acceptable access delay vty-configurable
and Ignores CHANnel ReQuireD RSL Messages with Access Delay IE greater
than that configured. Default value is 63.
Related: OS#5096
Change-Id: Ie8987bcc0e43921bc753162b77a0efc68799b3ce
On lchan activation, we already know the Timing Advance in most
situations: from the Channel Request RACH, or from a previous lchan in
the same cell. Place this information in lchan->activate.info.ta.
So far, the lchan->last_ta (until recently called rqd_ta) was used to
store the initial TA for channel activation -- move the initial TA to
lchan->activate.info.ta, for proper scoping.
Only an inter-cell handover does not yet know a Timing Advance (until
the Handover Detection RACH is received), so indicate
activate.info.ta_known = false for that case.
If ta_known is false, do not include an Access Delay IE in the Channel
Activation message, ensuring that the BTS does not use an arbitrary TA
that is likely inaccurate.
The effect for OsmoBTS is that we will *not* start the downlink SACCH on
channel activation for inter-cell handover, but will wait for a HO RACH
first, and then use the correct TA when enabling downlink SACCH.
Related: OS#4008 SYS#5192
Change-Id: I986bf93e8acd6aef7eaf63ac962480b680aa894f
Originally, the lchan stored only the Timing Advance from the initial
channel request, hence it was called rqd_ta.
Since quite a while now, rqd_ta also stores the most recent Timing
Advance from each received Measurement Report. So rename to last_ta.
This is cosmetic preparation for an upcoming patch that clarifies
whether the Timing Advance is already known for Channel Activation.
Change-Id: I1049526a173819baeb4978db5bf018ba3f1006a0
If an emergency call arrives at the BSC while all TCH are busy, one TCH
is cleared in favor of the emergency call. However, if emergency calls
are disabled (system information), it is still possible that an MS might
try an emergency call anyway or that due to interference a regular call
might look like an emergency call (channel request reason). In those
cases the preemption must not happen and the emergency call must be
rejected.
Change-Id: I1af1f4fefcbe6a886bb5396901ce0cb2368a0e19
Related: OS#4976
Add bool log argument to lchan_avail_by_type() and omit logging when
passed as false. From handover_decision_2.c, pass 'log' as false, from
all other callers pass true, i.e. for unchanged behavior.
Rationale:
Usually, we use lchan_avail_by_type() to select a new lchan to initiate
actual service. For that, it is interesting to see how osmo-bsc decides
which lchan will be used.
For handover decision 2, we since recently call lchan_avail_by_type()
for each and every handover candidate, to determine whether it will
occupy a dynamic timeslot or not (to know whether we would congest the
other TCH kind). So this happens for each permutation of source lchan
and target cell. That produces a lot of logging, out of proportion of
being useful to the maintainer.
Change-Id: Ia403f8fc853ca9ea9e81f7a7395df6b23845ebed
In order to activate FACCH/SACCH repetition on the BTS, the classmark 3
IE in the CLASSMARK CHANGE message must be parsed and depending on the
Repeated ACCH Capability bit the RSL_IE_OSMO_REP_ACCH_CAP is added to
the RSL CHAN ACT und RSL CHAN MODE MODIFY. Since
RSL_IE_OSMO_REP_ACCH_CAP is a propritary IE, it may only be added for
BTS type osmo-bts.
Change-Id: I39ae439d05562b35b2e47774dc92f8789fea1a57
Related: OS#4796 SYS#5114
The function reduce_rach_dos() only removes the tossed channel requests
from the list, but does not free them.
Change-Id: I0a62fc897c07e118dd637b156b6f2822c44db731
Related: OS#4549
At the moment expired channel requests are dropped silently, however, it
might help to know when this happens - not only for debugging.
Change-Id: Ib49df551a4cd7d5652e85c8ce29ef132385d4ae4
Related: OS#4549
when an emergency call arrives while all TCH are busy, the BSC should
pick an arbitrary (preferably the longest lasting) call / lchan and
release it in favor of the incoming emergancy call.
The release of the existing call is a process that can not be done
synchronously while the ChanRQD is handled sonce multiple messages are
exchanged between BTS and MSC and multiple FSMs need to do their work.
To be able to release one lchan while handling a ChanRQD a queue is
implemented in which the incomming channel requests are collected. If
an emergency call is established while all channels are busy, an
arbitrary lchan is picked and freed. When freeing the lchan is done,
the queue is checked again and the emergency call is put on the free
lchan (TCH/H or TCH/F).
Change-Id: If8651265928797dbda9f528b544931dcfa4a0b36
Related: OS#4549
osmo-nitb supports the modification of an lchan if the lchan is
compatible but in the wrong mode. This feature was dropped in the
transition to AoIP/bsc-split. However, osmo-bsc still has code to
generate and parse the messeages, but the FSMs do not support a mode
modify yetm
Lets add handling for mode-modify to the lchan_fsm and assignment_fsm in
order to support mode modify again
Change-Id: I2c5a283b1ee33745cc1fcfcc09a0f9382224e2eb
Related: OS#4549
Currently osmo-bsc encodes the IAR Rest Octets as follows:
IAR Rest Octets
0... .... = Extended RA: Not Present
.0.. .... = Extended RA: Not Present
..1. .... = Extended RA: Present
...0 1011 = Extended_RA: 11
0... .... = Extended RA: Not Present
.L.. .... = Additions in Rel-13: Not Present
Padding Bits: default padding
This is not really critical, but still may look confusing as this
is only relevant for the PS domain (11-bit RA), while osmo-bsc is
responding to a CHANNEL REQUEST in the CS domain.
Change-Id: I30a43efc70345a4bb0571127c239a24422b7fd2c
If a CHAN RQD indicates an emergency call on a BTS that does not allow
emergency calls, then respond with an IMMEDIAGE ASSIGNMENT REJECT
message to deny the emergency call early.
Related: OS#4548
Change-Id: I148c540269bffd703f38233a1e689e863c175e97
Place all code related to the object into the related file.
Having all the data model in one file made sense in early stage of
development to make progress quickly, but nowadays it hurts more than
helps, due to constantly growing size and more and more bits being
added to the model, gaining in complexity.
Currently, having lots of different objects mixed up in gsm_data.h is a hole
of despair, where nobody can make any sense were to properly put new stuff
in, ending up with functions related to same object in different files
or with wrong prefixes, declarations of non-existing functions, etc.
because people cannot make up their mind on strict relation to objects
in the data model.
Splitting them in files really helps finding code operating on a
specific object and helping with logically splitting in the future.
Change-Id: I00c15f5285b5c1a0109279b7ab192d5467a04ece
According to 3GPP TS 48.058 (version 15.0.0), section 9.3.5, the
3GPP TS 24.008 "Mobile Allocation" shall for compatibility reasons
be included but empty, i.e. the length shall be zero. Therefore,
no matter if frequency hopping is in use or not, send it empty.
Change-Id: Ie224a45f10522332eac653fa371564f022108c3f
Related: OS#4545, OS#4546
If the BTS downlink CCCH (PCH + AGCH) queue is full, it sends
us an RSL DELETE INDICATION. So far, osmo-bsc logs this as
<0004> abis_rsl.c:2026 Unimplemented Abis RSL TRX message type 0x14
which is not very helpful. Instead, make the log message more
descriptive and add a rate counter for monitoring.
Change-Id: I9bd2966db90e39ccca442d6bc9abc91e9a9147d4
Closes: OS#3190
Not sure why this specific message is ERROR while similar ones around
are DEBUG. So let's fix this disparity by demoting this message level.
Change-Id: I655d4555f037def354aacbc5f089794f5fe811ed
The "CHAN RQD: reason" message is purely informational and is a part
of normal operation. Nothing to NOTICE there. Let's demote this to
DEBUG.
Change-Id: I325f2beb3248ed8eb25d1d8494c3868c5be4b758
Lots of times, the MS power class is unknown until after the first
channel has been activated, at which point the MS power class is
received in messages such as LU update or CM Service Requet.
Since the MS Power level is sent upon CHAN ACT, the only way to
communicate the change of maximum MS Power (based on MS power class)
after CHAN ACT is to send a MS Power Control msg. Let's do that.
Related: OS#4244
Change-Id: I3d6b75578e5cb9b2ad474a0ad01362d846ebe135
Since MS Power Param IE content is operator dependant, it's currently
not known which kind of content non-osmocom BTS support/allow, so let's
avod possibily breaking those BTS until each BTS has been checked
separately.
Related: OS#1622
Change-Id: If44121222042bdac06c2a5e70f7b35a88b00b27c
Further accesses will be addter in forthcoming commit, so let's first
store the pointers in variables to clean up the code.
Change-Id: Ie5ea0f44dfb5731cab7e8e5a3dd3d791ee703df7
TS 48.058 sec 8.4.1 CHANNEL ACTIVATION and state:
"""
The BS and MS Power Parameters elements are included to indicate that BS
and/or MS power control is to be performed by BTS. The maximum power to
be used is indicated in the BS and MS Power elements respectively.
"""
Since we always want the BTS to do autonomous MS power control, let's
add it.
Related: OS#1622
Change-Id: Icaaa61b363b093f00b6653c3df64d3e66583b9f8
In addition to transmission of the ETWS Primary Notification via all
dedicated channels, we also need to send it to the BTS for transmission
via PCH (P1 Rest Octets) and for forwarding to PCU for PACCH
transmission.
Change-Id: I7e45b0373458a4348b12b92dd92861062532548b
This adds code to handle CBSP (Cell Broadcast Service Protocol)
from the CBC (Cell Broadcast Centre), as well as BSC-internal data
structures for scheduling the various SMSCB on the CBCH of each BTS.
There are currently one known shortcoming in the code: We don't yet
verify if keepalives are received within repetition period.
Change-Id: Ia0a0de862a104d0f447a5d6e56c7c83981b825c7
Neels Hofmeyr
Pau Espin
Keith Whyte
Philipp Maier
Vadim Yanitskiy
Harald Welte
Daniel Willmann
Martin Hauke